Dynex Outdoor Cart DX WD1239 User Manual

ASSEMBLY INSTRUCTIONS

DX-WD1239

TV Cart

Safety information and specifications ............2

Tools needed............................................................3

Package contents ...................................................3

Assembly instructions...........................................5

DX-WD1239

Tools needed

No. 2 Phillips screwdriver

Hammer

Caution: Do not

use an electric drill

or screwdriver

Package contents

Package contents: hardware

Make sure you have all the hardware necessary to assemble your new TV cart:

Label

Hardware

Qty.

Label

Hardware

Qty.

Hidden cam

Metal pin

Rubber sleeve

Cam dowel

Warning

label

Swivel caster

Non-swivel

caster

Using a screw that is too long will cause damage your TV cart. Before beginning assembly, separate each

type of screw. Carefully study the screw table below. You can use the ruler at the bottom of the screw

table to measure screws. Pay close attention to the color of each screw.

You may receive extra hardware with your TV cart.

Letter

Description

Qty. Letter

Description

Qty.

Black 1 7/8" (47.75 mm) flat head screw

Black 9/16" (14.22 mm) large

head screw

4in

100mm

Need help? Call 800-305-2204

DX-WD1239

Package contents: parts

Note: All parts except for the stop molding (H) have a lettered sticker to make identifying parts easier.

Letter

Description

Right end

Qty. Letter

Description

Bottom

Qty.

Left end

Upright

Top

Adjustable shelf

Valance

Stop molding

Need help? Call 800-305-2204

DX-WD1239

Assembly instructions

Step1:

Assemble your TV cart on a carpeted floor or on the empty carton to avoid scratching your TV cart or the

floor.

Push nine hidden cams (I2) into the ends (A and B), upright (C), and top (D), then insert the metal end of a

cam dowel (J2) into each hidden cam.

Do not tighten the hidden cams in this step.

Arrow

You’ll need:

I2 (9)

J2 (9)

Need help? Call 800-305-2204

DX-WD1239

Step 2:

Insert two metal pins (M) into the two holes beside the hidden cam on the right end (A).

Repeat this step for the left end (B).

You’ll need:

M (4)

Need help? Call 800-305-2204

DX-WD1239

Tightening hidden cams

In the remaining steps, use these illustrations for instructions on tightening hidden cams.

Warning: Risk of damage or injury. Hidden cams must be completely tightened. Hidden cams that are not

completely tightened will loosen, and parts may separate.

Arrow

Make sure that you turn the

hidden cam a minimum of

190° to a maximum of 210°.

Note the position of the arrow

on the hidden cam.

Arrow

210°

In the illustration below,

the hidden cam has not

been tightened enough.

190°

You’ll need:

Phillips screwdriver

Need help? Call 800-305-2204

DX-WD1239

Step 3:

Fasten the stop molding (H) to the top (D). Use a Phillips screwdriver to tighten three hidden cams. See

“Tightening hidden cams” on page 7.

Unfinished

surface

Arrow

Maximum210°

Minimum 190°

You’ll need:

Phillips screwdriver

Need help? Call 800-305-2204

DX-WD1239

Step 4:

Fasten the left end (B) to the top (D). Use a Phillips screwdriver to tighten two hidden cams. See “Tightening

hidden cams” on page 7.

Finished

edge

Arrow

Maximum 210°

Minimum 190°

You’ll need:

Phillips screwdriver

Need help? Call 800-305-2204

DX-WD1239

Step 5:

Slide the valance (G) onto the two metal pins (M) in the left end (B).

Unfinished

surface

Finished

edge

Need help? Call 800-305-2204

DX-WD1239

Step 6:

Fasten the right end (A) to the top (D). Use a Phillips screwdriver to tighten two hidden cams. See “Tightening

hidden cams” on page 7.

Note: Make sure that the metal pins in the right end (A) insert into the holes in the valance (G).

Finished

edge

Arrow

Maximum 210°

Minimum 190°

You’ll need:

Phillips screwdriver

Need help? Call 800-305-2204

DX-WD1239

Step 7:

Fasten the upright (C) to the top (D). Use a Phillips screwdriver to tighten two hidden cams. See “Tightening

hidden cams” on page 7.

Fasten the bottom (E) to the ends (A and B) and upright (C). Use a Phillips screwdriver and six black 1 7/8" flat

head screws (P).

Screw holes

Long finished edge

Unfinished

surface

Finished edge

Arrow

Maximum 210°

Minimum 190°

You’ll need:

P (6)

Phillips screwdriver

Need help? Call 800-305-2204

DX-WD1239

Step 8:

Fasten the swivel casters (K) and the non-swivel casters (L) to the bottom (E). Use a Phillips screwdriver and

16 black 9/16" large head screws (Q) (four screws per caster).

The tabs on the

non-swivel casters (K)

must insert into these

holes.

You’ll need:

Phillips screwdriver

Q (16)

Need help? Call 800-305-2204

DX-WD1239

Step 9:

Carefully stand your TV cart upright.

Push the rubber sleeves (N) on the metal pins (N), then insert the metal pins into the hole locations of your

choice in the right end (A) and upright (C). Set the adjustable shelf (F) onto the metal pins (M).

Apply the warning label (O) to the top (D). You should be able to read the label when the TV is removed from

your TV cart. When the TV is in place, it should hide the label. Peel off the backing and apply the label as

shown.

Caution: This is a permanent label intended to last for the life of the product. Once applied, do not try to

remove it. You may damage the finish on the top.

Warning: Never use this

furniture with a TV that is too

large or too heavy. Severe

injury or death can occur. The

TV and furniture will be

unstable and may tip.

•

The TV must weigh less

than 95 lbs.

The base of the TV must

be able to sit completely

on this shelf.

•

95 lbs

(43 kg)

25 lbs

(11 kg)

30 lbs

(13 kg)

Metal pin

with

rubber

sleeve

You’ll need:

M (4)

N (4)

Need help? Call 800-305-2204

DX-WD1239

Still need help?

For customer service, call: 800-305-2204 (U.S./Canada markets)

Distributed by Best Buy Purchasing, LLC

7601 Penn Avenue South, Richfield, MN USA 55423-3645

products and brand names are trademarks of their respective owners.

Need help? Call 800-305-2204

Certificate of Conformity

1. This certificate applies to the Sauder

Woodworking Product identified by this

instruction booklet.

2. This certificate applies to the compliance of this

product with the CPSC Ban on Lead-Containing

Paint (16 CFR 1303).

3. This product was manufactured by:

Sauder Woodworking Company

502 Middle Street

Archbold, Ohio 43502

(419) 446-2711

4. Date of Manufacture: ____________

Lot number: 346230

www.dynexproducts.com (800) 305-2204

Distributed by Best Buy Purchasing, LLC

7601 Penn Ave. South, Richfield, MN 55423 U.S.A.

DYNEX is a trademark of BBY Solutions, Inc. Registered in some countries. All other products and

brand names are trademarks of their respective owners.

12-0784

ENGLISH

Cisco Systems Network Hardware BC 281 User Manual
Craftsman Lawn Mower 1072777 User Manual
D Link Network Router DWR 116 User Manual
Dyson Patio Heater AM 04 User Manual
Edimax Technology Server PS 1206MF User Manual
Electro Voice Microphone RE98 User Manual
Electro Voice Portable Speaker S 152 User Manual
EverFocus Car Video System EN 7517C User Manual
Fitness Quest Home Gym 95e User Manual
Global Machinery Company Trimmer RM1000 User Manual