HEAT GUN KIT
HG 1800K
OPERATING INSTRUCTIONS
Thank you for purchasing the Earlex HG1800K Heat Gun Kit,
this is a highly versatile kit that can be used in a
variety of applications.
BEFORE USE - PLEASE READ THE SAFETY &
OPERATING INSTRUCTIONS
Please retain for future reference
Heat Settings
Suggested Ratings
The heat gun
has a variable
heat setting in
order to give
greater control
over the
working
temperature.
Paint Stripping
Bending Plastic
Defrosting Pipes
Heat shrinking plastic Low Setting
Nozzles
The kit is supplied with 4 different
shaped nozzles, which can be used
as follows.
High Setting
Medium Setting
Low Setting
To adjust the heat setting move the
wheel at the back of the gun. The
five red lights on the left hand side
of the gun show the temperature
range selected.
Concentrator Nozzle
This nozzle directs
a concentrated
heat flow to the
workpiece. It is
To increase the temperature, move
the wheel up on the left hand side
of the gun, and to decrease the
temperature move the wheel down
on the left hand side of the gun.
The approximate temperature
setting is also shown on the dial at
the back of the gun.
ideal for use when
removing paint in
awkward corners,
crevices,
mouldings, beading, architrave’s or
whenever precise paint removal is
required.
Concentrator Nozzle
Deflector Nozzle
This nozzle directs
a long narrow
heat pattern to the
workpiece, and is
OPERATION
Before starting the job it is
advisable to test the workpiece for
the ideal temperature to use. The
table below gives an indication of
the likely heat settings required but
always start with the low heat
setting.
The distance between the nozzle
and the workpiece will vary
according to the material being
worked on but this should always
be at least 50mm (2”).
All applications, with the exception
of removing paint from the window
frames, can be performed without
using a nozzle, however for best
results nozzles are recommended.
ideal for removing
paint or varnish
Deflector Nozzle
from large flatsurfaces such as
skirting boards, doors, stairs etc. It
should be used in conjunction with
a flat scraper. Vinyl tiles can be
removed by softening the adhesive.
Glass Protection Nozzle
This nozzle
deflects the heat
away from glass
or other fragile
areas and back
onto the
workpiece.
Glass Protection
Nozzle
3
Hook Nozzle
This nozzle
disperses the
heat flow
evenly around
the whole
workpiece. It is
ideal for
defrosting frozen pipes, soldering
pipe work, bending plastics and
heat-shrinking electrical parts.
Removing Paint
Choose the required nozzle and fit
onto the heat outlet. Select the
scraper or shavehook required.
Hold the gun with the nozzle
approximately 50mm (2”) from the
surface of the paintwork and
starting with the lower heat setting
move it slowly backwards and
forwards until the paint blisters and
bubbles. Immediately remove the
paint with the scraper or
Hook Nozzle
Shavehooks
Select the required blade from the
set. Take the
shavehook
handle from the
set, remove the
nut from the end,
fit the required
blade then fix in
place by refitting
shavehook. Aim to heat the paint
just ahead of the scraper so that
you can develop a continuous
action. Do not heat the paint for too
long, as this will burn the paint
making it difficult to remove.
Most stickers can also be removed
from paintwork by using the heat to
soften the adhesive. Be careful not
to direct the heat for too long if you
are trying just to remove the
Triangular Shavehook
and tightening the
nut.
stickers, as this will blister the paint.
Use the triangular
shavehook for
stripping paint
from flat wooden
surfaces and
edges, use the
combination or
heart shavehooks
for mouldings in
convex or concave
profiles.
Removing paint from window
frames
Always use the glass protection
nozzle. Ensure you have the nozzle
facing the correct way to deflect the
heat away from the glass before
you switch on. Rotate the gun or
nozzle 90o as you move to
horizontal or vertical bead. Allow
nozzle to cool before attempting to
turn it. Paint can be removed from
profile surfaces by using a
Combination
Shavehook
Heart Shavehook
Remember to
clean the blade
after use with
wirewool and
lightly oil before
storing.
shavehook and/or a soft wire brush.
WARNING: Be careful Glass can
break easily due to sudden
temperature change!
Assembly
of Shavehook
Not suitable for PVC frames!
4
the tube, fill the tube with dry sand
and seal at both ends. Heat the
tube evenly by moving from side to
side and bend to required shape.
WARNING: Protect hands from
heat.
Defrosting frozen pipes
Choose the Hook nozzle and fit
over the heat outlet. Always heat
from one or other end of the frozen
portion, not from the middle.
WARNING: Do not attempt to
defrost PVC pipes. Always check
that it is a water pipe and not a
gas pipe. Do not heat a gas pipe.
Shrink sealing electrical cables
Choose the Hook nozzle and fit
over heat outlet. Select a heat-
shrinkable sleeve with a diameter
matching that of the workpiece.
Evenly heat the sleeve.
Bending Plastic Tubing
Welding plastics
Choose the Concentrator or
Deflector nozzle and fit over heat
outlet. The materials being welded
together must be of exactly the
same type of plastic. The areas
being welded must be clean and
grease-free. Heat the seam until the
plastic becomes tacky, then apply
the other surface.
Cooling
The nozzle of the heat gun can
become very hot during use.
Always allow
the heat gun
to cool after
use. Switch
off the heat
gun and
WARNING: Plastic can very
quickly change from being tacky
into becoming liquid. Beware of
burns from hot plastic. Do not
remove molten plastic from a
burn. Run under cold water and
seek medical advice.
disconnect
form the
power supply.
Stand the heat gun upright as
shown to allow convection currents
to cool the nozzle.
To speed up the cooling time, set
the heat setting to the minimum and
run the heat gun for 2-3 minutes.
Always allow at least 30 minutes for
the heat gun to cool after switching
off.
Bending plastic tube
Choose the Hook nozzle and fit
over heat outlet. Turn the gun
upside down and place on it’s
stand so that it is resting on a
secure bench with the nozzle
pointing upwards; see picture
below. To avoid buckling or kinking
Always make sure that the heatgun
cannot be pulled by the mains
cable whilst cooling.
5
If an extension cable is used it must
be fully unwound and rated at least
10amps capacity.
Maintenance
The heat gun should be cleaned
before being stored away by wiping
over with a clean damp cloth after
ensuring that the gun has cooled;
do not use any chemicals. Ensure
that the ventilation slots are not
blocked.
If unit has over heated allow unit to
cool further before operating, this
may take up to 20 minutes. - see
cooling section
IF YOU REQUIRE FURTHER
ASSISTANCE PLEASE CONTACT
OUR HELPLINE NO.
Trouble Shooting
If a problem occurs always
switch the unit off immediately.
Unit fails to work:
Check the fuse in the plug is sound
and rated 13amps.
01483 454666
(www.earlex.co.uk)
Monday - Friday 08:30 - 17:00
(Excluding Bank Holidays)
MAINS CONNECTION
Your unit has been supplied with a mains lead with a fitted moulded plug. This is
identified by the fuse holder in the base of the plug. Please read the following
safety instructions before use.
If the moulded plug is cut off from the mains lead then the plug must be disposed
of safely.
1
NEVER under any circumstances insert such a plug into a 13 amp socket.
NEVER under any circumstances use the appliance without the fuse cover fitted.
This is the little cover fixed into the base of the plug to hold the fuse in place.
If you lose the fuse cover then please contact any electrical dealer for a
replacement or ring our helpline.
2
3
A replacement fuse must be rated at 13amp. The fuse must be manufactured and
approved to BS1362.
IF IN ANY DOUBT PLEASE CONTACT AN ELECTRICIAN.
If you need to fit a plug to the mains lead, this should be fitted in accordance with
the wiring instructions as shown below, and will need to be used with a 13 amp
fuse. If in doubt consult an electrician.
4
5
If you are using an extension lead it must be rated at a minimum of 10 amps and
fully unwound. Do not operate with a lead rated at less than 10 amps as this will
cause premature failure of the element which is not covered by the guarantee.
As the colours of the wires in the mains lead of this appliance may not
correspond with the coloured markings identifying the terminals in your plug,
proceed as follows:
The wire which is coloured blue must be connected to the terminal which is
marked with the letter N or coloured black.
The wire which is coloured brown must be
connected to the terminal which is marked with the letter
L or coloured red.
6
GUARANTEE
This heat gun is guaranteed for a period of 2 years against faulty
manufacture or materials. It is not guaranteed for industrial or hire
purposes. The scraper, shavehooks and nozzles are classed as
consumables and are not covered by guarantee. This guarantee does
not affect your statutory rights.
In the event of any problem occurring please contact us on our
Helpline no.
01483 - 454666
Monday - Friday 08:30 - 17:00 (Excluding Bank Holidays)
email:[email protected]
EC Declaration of Conformity
We declare that the unit: HG1800 conforms to: 73/23/EEC
EN60335-1, EN60335-2-45 & 89/336/EEC EN61000-3-2,
EN61000-3-3 & EN55014
Tim Hopper - Technical Director
7
OTHER PRODUCTS FROM EARLEX
Steam Wallpaper Strippers: Designed to
remove all types of wallpaper, multi-layered
papers and artex®.
life. Kit includes 0.6mm & 1mm nozzles &
3-IN-ONE®oil. Check the Earlex website for
up - to-date information on what you can
spray.
SS100 - 2300W 4.5 ltr steam wallpaper
stripper
SS50 - 2000W 4.5 ltr steam wallpaper
stripper
SG75-Super Sprayer 75- 85W Electric
Airless Spray Gun. The motor size and
larger additional nozzle (0.8mm) allows
thicker viscosity liquids such as emulsions,
latex, laquers and impregnating agents to be
sprayed. Includes a flexible extension nozzle
that is ideal for spraying overhead and at
different angles. Supplied with 2 nozzle sizes
and a spares kit.
A range of steam cleaning accessories are
also available to be used in conjunction with
the steam wallpaper strippers. The
accessories can be used to clean and
rejuvenate carpets, floor tiles, unblock sinks
or waste outlets, clean work surfaces,
defrost fridges and freezers, clean windows
and tiles, remove soiling from upholstery and
curtains.
Alternatively the CombiSteam combines the
versatility of the steam wallpaper stripper
with a selected range of the accessories
providing you with a complete steam
cleaning kit and wallpaper stripper.
SC165 - 1500W 4.5 ltr steam cleaning kit,
incl. carpet cleaner, window/tile cleaner, jet
nozzle cleaner, upholstery cleaner / small
steamplate, large wallpaper stripping plate.
SG85-Super Sprayer 85- 85W Electric
Airless Spray Gun. The SG85 is a heavy
duty spray gun designed for the semi-
professional/tradesman with a tungsten
carbide piston and a die-cast aluminium
head. These allow the product to deal with
abrasive materials such as exterior wall
paints (non-grit), latex, pottery glazes and
similar materials that may be sprayed.
Includes a remote suction cup that clips onto
the paint can, so that there is no need to
keep refilling the paint container. Supplied
with 2 nozzle sizes and a spares kit.
PR9 - The Autofeed Paint Roller is a
portable battery operated paint rolling
system. It has a 3 litre paint reservoir and
230mm (9”) roller and automatically feeds
the paint to the roller head. No trays need to
be refilled or moved. Easy to use the PR9
provides enough capacity for one coat of a
3.6m x 2.7m (12’ x 9’) room without having
to refill.
WD1000 CombiVac Wet’n’Dry & Blower-
The 1000W motor provides a powerful
suction and blowing facility which is ideal for
use around the workshop, garage, caravan,
car, garden and home. The 20 litre recovery
tank has 12 litres wet capacity and is
designed for the rough and tumble of
everyday use. The Combivac has on board
storage facilities for its accessories, 6 metres
of working length and a two year guarantee.
There is also a variety of additional
ASG55 Super Sprayer - Sprays a 6’x6’
fence panel in 5 minutes!
55W Electric Airless Spray Gun, ideal for
spraying wood preservatives, shed & fence
treatments, water and solvent based paints.
Ideal for shed, fences and trellis. It has a 1
litre capacity, easy-grip handle that provides
good balance and control. Hardened steel
cylinder and stainless steel piston for longer
accessories available for use with the
Combivac.
If you require further information on any of
our other products, please telephone or write
to the address below, or visit our website at
Earlex Ltd.,
19 Moorfield Road, Slyfield Industrial Estate,
Guildford, Surrey. GU1 1RU. ENGLAND.
Tel: +44(01) 01483 - 454666. Fax: +44(01) 01483 - 454548.
email:[email protected]
G31 09/01
© Earlex Ltd. 2001
8
|