M107-N501-001
HIGH PERFORMANCE
Super Night Vision Camera
OPERATION MANUAL
Thank you for choosing our high quality camera. Before attempting
to connect operate this unit,please read and follow these instructions.
CONTENTS
1. CAUTIONS
2. IMPORTANT SAFETY INSTRUCTIONS
3. FEATURES
4. COMPONENTS
5. NAME AND FUNCTION
6. INSTALLATION
7. DIMENSIONS
8. SPECIFICATION
9. OSD MENU STRUCTURE
3
1. CAUTIONS
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions;
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
Note
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.”
WARNING
This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
Caution
Any changes or modifications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
1. A regulated DC12V 1A power supply is recommended for use with this camera
for the best picture and the most stable operation.
An unregulated power supply can cause damage to the camera.
When unregulated power supply is applied, product warranty will be
out of subject.
2. It is recommended that the camera is used with a monitor that has a CCTV quality
75 video impedance level.
If your monitor is switched to high impedance then please adjust accordingly.
3. Do not attempt to disassemble the camera to gain access to the internal componets.
Refer servicing to your dealer.
4. Never face the camera towards the sun or any bright or reflective light, which may
cause smear on the picture and possible damage to the CCD.
5. Do not remove the serial sticker for the warranty service.
4
1. CAUTIONS
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with
separate collection systems)
This marking shown on the product or its literature, indicate that it should not
be disposed with other household wastes at the end of its working life. To
prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.
This product should not be mixed with other commercial wastes purchased this
product, or their local government office, for details of where and how they can
take item for environmentally safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract.
Household users should contact either the retailer where they for disposal.
5
2. IMPORTANT SAFETY INSTRUCTION
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide blade or the third prong are
provided for your safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus combination to
avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long
periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when
the apparatus has been damaged in any way, such as power-supply cord or plug
is damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.
6
3. FEATURES
• 1/3 960H SONY EXview HAD CCD II
• High Resolution of 700TV Lines
• OSD Function
• Multi Language
(ENGLISH / JAPANESE / GERMAN / FRENCH / RUSSIAN / PORTUGUESE / SPANISH / CHINESE)
• 2DNR
• Privacy Zone / Motion Detect
• Invisible IR
• DC12V / AC24V Dual Voltage
• ATR(Adaptive Tone-curve Reproduction / Digital WDR)
The function provides gradation compensation to improve the contrast of subjects both
low-luminance areas and high luminance areas exist in the same picture
4. COMPONENTS
SUPER NIGHT VISION CAMERA
SUNSHIELD
VIDEO OUTPUT
TEST CABLE
L-WRENCH /
SCREW - 3ea /
SUNSHIELD FIXING BOLT
OPERATION MANUAL
7
5. NAME AND FUNCTION
①
②
①
③
④
⑤
⑧
⑥
⑦
① Sunshield Fixing Bolt
② Sunshield
③ Mounting Bracket
④ LED : 20ea
⑤ Photo cell
⑥ Body
⑦ Body Fixing Ring
⑧ External Zoom and Focus adjustment
8
6. INSTALLATION
• MOUNTING POSITION
360˚
90˚
After adjusting zoom and focus,
to prevent water infiltration, firmly
tighten the zoom and focus lever.
360˚
9
6. INSTALLATION
• MONITOR CONNECTION
(1) DC12V
DC12V POWER SUPPLY
DC12V
BNC FEMALE
VIDEO IN
(2) DUAL(DC12V/AC24V)
DC12V /AC24V POWER SUPPLY
DC12V/AC24V
BNC FEMALE
VIDEO IN
When you install the camera, please glue up the end of cable to
keep it stable in order to protect the camera from the humidity problems.
10
7. DIMENSIONS
82
145
120
224
M12 XP1.0
Ф65
11
8. SPECIFICATION
Signal Format
NTSC
1/3˝ 960H SONY EXview HAD CCD II
2 : 1 Interlace
PAL
Image Device
Scanning System
Scanning Frequency
Total Pixels
15.734KHz(H), 59.94Hz(V)
1020(H) X 508(V)
976(H) X 494(V)
1/60 sec
15.625KHz(H), 50Hz(V)
1020(H) X 596(V)
976(H) X 582(V)
1/50 sec
Effective Pixels
Electronic Shutter Speed
H.Resolution
700TV Lines
S/N Ratio
More than 50dB(AGC OFF)
LED Off : COLOR (0.05Lux / F1.2), BW (0.02 Lux / F1.2)
LED On : 0 Lux
Min.Illumination
Sync System
Gamma
Video Output Level
OSD
Internal
r= 0.45
1.0 Vp-p Composite(75Ω)
Built in (Inner Key / Joystick)
OFF/BLC/HLC
BLC
2DNR
OFF/ON(Level adjustable)
OFF/ON(Level adjustable)
ATR
Function
ATW / PUSH / USER1 / USER2 / ANTI CR / MANUAL / PUSH-LOCK
White Balance
ATW / PUSH / USER1 / USER2 / ANTI CR / MANUAL / PUSH-LOCK
Privacy Masking
Motion Detection
Day & Night(ICR)
4 Zones
4 Zones
AUTO
ENGLISH / JAPANESE / GERMAN / FRENCH / RUSSIAN /
PORTUGUESE / SPANISH / CHINESE
Language
IP Rating
IP66 (Weatherproof)
940nm, 20ea
IR LED
IR LED Distance
Operating Temperature
Up to 25M
14°F~122°F(-10°C~+50°C)
Storage Temperature
Humidity
-4°F~140°F(-20°C~+60°C)
Less than 80%
Power
DC12V Only : DC12V (±10%), Max.270mA
Consumption
Dual : DC12V (±10%) Max.360mA , AC24V (±10%) Max.4.9W
Lens
Varifocal Lens
82.0(W) x 79.3(H) x 145(D)
Approx. 900g
Dimension
Weight
Specifications and designs are subject to change for improving the functionality of this product without notice.
12
9. OSD MENU STRUCTURE
MAIN
1st Sub
2nd Sub
MENU
3rd Sub
4th Sub
MENU
MENU
MENU
MENU
MANUAL
TYPE
DC
AUTO,OPEN,CLOSE
(000 255)
LENS
MODE
SPEED
AUTO
AUTO
~
RETURN
MODE
SHUT,AUTO IRIS, SHUT+AUTO IRIS
HIGH LUMINANCE
BRIGHTNESS
MODE
(000
~
255)
AGC,OFF
LOW LUMINANCE
BRIGHTNESS
x0.25,x0.50,x0.75,x1.00
RETURN
MODE
SHUTTER
AGC
SHUT+AGC
/
1/50(PAL),1/100(NTSC)
1/60(NTSC),1/120(PAL)
1/250,1/500,1/1000
SHUTTER
MANUAL
1/2000,1/4000,1/10000
AGC
6,12,18,24,30,36,42,44.8
RETURN
SPEED
(000
(000
~
~
255)
255)
DELAY CNT
ATW FRAME
ENVIRONMENT
RETURN
x0.50,x1.00,x1.50,x2.00
INDOOR,OUTDOOR
ATW
PUSH
B-GAIN
R-GAIN
RETURN
B-GAIN
R-GAIN
RETURN
(000
(000
~
~
255)
255)
USER1
WHITE
BAL
(000
(000
~
~
255)
255)
USER2
ANTI CR
LEVEL
24
~
103
MANUAL
RETURN
PUSH LOCK
BACK LIGHT OFF,BLC,HLC
MIRROR
OFF,ON
(000
(000
(000
(000
(000
~
~
~
~
~
255)
255)
255)
255)
255)
BRIGHTNESS
CONTRAST
PIC
ADJUST
SHARPNESS
HUE
GAIN
RETURN
LUMINANCE
CONTRAST
RETURN
LOW,MID,HIGH
LOW,MIDLOW,MID,MIDHIGH,HIGH
ON
ATR
OFF
*SHUT+IRIS: Both the Shutter and the Mechanical Iris are automatically adjusted according to brightness.
*Auto Iris(Default): The Shutter stays at the manually selected value and only the Mechanical Iris adjusts to brightness.
13
9. OSD MENU STRUCTURE
MAIN
1st Sub
2nd Sub
MENU
3rd Sub
4th Sub
MENU
MENU
MENU
MENU
(000
~
255)
DETECT SENSE
BLOCK DISP
OFF,ON,ENABLE (CONTROLER)
ON,OFF
1/4, 2/4, 3/4, 4/4
TOP
MONITOR AREA
ON
NTSC:(000 ~ 244) / PAL: (000 ~ 288)
NTSC:(000 ~ 244) / PAL: (000 ~ 288)
NTSC:(000 ~ 474) / PAL: (000 ~ 468)
NTSC:(000 ~ 474) / PAL: (000 ~ 468)
MOTION
DET
AREA SEL
RETURN
BOTTOM
LEFT
RIGHT
OFF
NEXT
EXIT
SAVE ALL
1/4, 2/4, 3/4, 4/4
TOP
NTSC:(000 ~ 244) / PAL: (000 ~ 288)
NTSC:(000 ~ 244) / PAL: (000 ~ 288)
NTSC:(000 ~ 474) / PAL: (000 ~ 468)
NTSC:(000 ~ 474) / PAL: (000 ~ 468)
AREA SEL
BOTTOM
LEFT
RIGHT
ON
PRIVACY
(1
~
8)
COLOR
0.00, 0.50, 0.75, 1.00
OFF,ON
TRANSP
MOSAIC
RETURN
OFF
NR MODE
OFF,Y,C,Y/C
C
Y
LEVEL
LEVEL
(000
(000
~
~
015)
015)
NR
RETURN
ON
EDIT MODE
RETURN
CAMERA
ID
OFF
LANGUAGE
ENGLISH, 日本語, DEUTSCH, FRANCAIS, Русский, PORTUGUÊS, ESPAÑOL, 中文
CAMERA
RESET
BACK
EXIT
SAVE ALL
*Important Note :
• Any changes made to the camera settings must be saved prior to
exiting the OSD menu. Else all changes will be discarded.
• By changing the lens option in the OSD from MANUAL to AUTO will automatically
change the SHUTTER/AGC setting from AUTO IRIS to SHUT+AUTO IRIS.
(Default:AUTO IRIS)
14
|