ZIF360NX
GE Monogram® 36" Built-In Custom All-Freezer
Dimensions and Installation Information
ZIF360NXRH, Freezer
Handle on the left side, the door swings left to right.
35"
Case Width
25-3/8" Framed Models
Case Depth
ZIF360NXLH, Freezer
Handle on the right side, the door swings right to left.
*84" From
Floor to
Top Frame
*83-1/2"
at
Caution
Rear
These units are top-heavy and must be secured to prevent the
possibility of tipping forward. Anti-Tip protection is required.
36" Frame to
Frame Width
Depth Including Handles:
26-7/8" Framed Models
*Shipping height. The freezer can be adjusted to fit into
a cutout 83-1/2" min. to 84-1/2" max. height. Note: the
top case trim at the front is 1/2" higher and will overlap
upper cabinetry or soffit. Use leveling legs and wheels for a
maximum 1" height adjustment.
Product Clearances
These units are equipped with a 2-position door stop. The fac-
tory set 130˚ door swing can be adjusted to 90˚ if clearance
to adjacent cabinets or walls is restricted. Order WX14X99
door stop for precise settings between 90˚and 130˚.
25"
Minimum
to Wall
23-7/8"
Behind Frame
90ϒDoor Swing
130ϒDoor Swing
36-3/4"
The water and electrical supply must be located as shown.
The finished cutout width must be 35-1/2".
Note: The case trim overlaps cabinets at the top and
sides. Frameless cabinets may require filler strips to
prevent interference with cabinet door swing. The opening
width must allow for filler strips.
4" Min.
to Wall
Allow 25" minimum clearance for a full 130˚ door swing.
Allow 15" for pan removal. for a 90˚ door swing, allow 4"
minimum clearance for professional models. If the 90˚
doorstop position is used, pan access is maintained but
pan removal is restricted.
For answers to your Monogram,® GE Profile™
or GE® appliance questions, visit our website
at ge.com or call GE Answer Center® service,
800.626.2000.
Listed by
Underwriters
Laboratories
Specification Created 6/08
110153
ZIF360NX
GE Monogram® 36" Built-In Custom All-Freezer
Dimensions and Installation Information
All-Refrigerator,
5/16"
All-Freezer 1/4" Framed
Trim
Door/
Drawer
Reveal
Panel
If you choose to install framed
panels, they must be cut to the
dimensions shown. The panels
will slide into the frame on the
door and grille.
1/4"
Panel
If the panel is less than 1/4" thick,
it must be backed up with filler
material or foam tape to improve
the fit.
1/4" Framed Panel Dimensions
A (Width)
ZUG2 Grille Panel Dimensions
The ZUG2 unified grille panel kit provides for the installation of
a framed or overlay grille panel.
B (Grille Height) C (Door Height)
8-7/8" 69-5/16"
Framed Panel
33-7/8"
A
IMPORTANT NOTE: Maximum weight
for the door panel is 67 pounds.
Maximum total weight for the
A
Grille Panel
B
B
Grille Panel
assembled grille panel is 11 pounds.
Panel Dimensions
A (Width)
B (Grille Height)
1/4" Framed Panel
69-7/8"
8-7/8"
Door
Panel
C
Panel Dimensions
A (Width)
69-7/8"
68-1/2"
B (Grille Height)
1/4" Framed Panel
0.10" Spacer Panel
3/4" Overlay Panel
8-7/8"
7-5/8"
9"
3/4" Overlay Panel Dimensions
70-1/8"
A (Width)
33-7/8"
32-1/2"
34-1/8"
B (Grille Height) C (Door Height)
1/4" Backer Panel
0.10" Spacer Panel
3/4" Overlay Panel
8-7/8"
7-5/8"
9"
69-5/16"
67-15/16"
69-9/16"
IMPORTANT:
Grille panel maximum total weight is 25 lbs..
For answers to your Monogram,® GE Profile™
or GE® appliance questions, visit our website
at ge.com or call GE Answer Center® service,
800.626.2000.
Listed by
Underwriters
Laboratories
Specification Created 6/08
110153
ZIF360NX
GE Monogram® 36" Built-In Custom All-Freezer
Dimensions and Installation Information
All-Refrigerator, All-Freezer 3/4" Overlay Panel
Overlay panels may be installed on trimmed units.
Door/
The overlay panel must be secured to a 1/4" thick backer
Drawer
Overlay
Panel
panel which slides into the trim. A 0.10" thick spacer panel
must be placed between the custom and backer panel.
Assemble overlay panels with glue and screws.
• Center spacer panel on the backer panel left to right and
top to bottom. Secure the panels with glue.
• Center the spacer/backer panel on the overlay panel and
secure with glue and screws. Screws must be countersunk
into the backer panel.
Note: Left-to-right offset is not always equal to top-to-bottom
offset.
1/4"
.10"
Spacer
Backer
Panel
Optional Accessories
Order these accessories from your Monogram supplier.
Overlay Panel
Spacer Panel
Backer Panel
ZKHPSS2, Professional Handle Kit
Professional stainless steel tubular handle designed to fit 3/4"
overlay panels. Note: Kit includes one Professional handle,
31" long.
ZKHSS2 Tubular Handle Kit
Monogram stainless steel tubular handle designed to fit 3/4"
overlay panels. Note: Kit includes two tubular handles, 62-3/8",
3/4" diameter.
ZUG2 Unified Grille Panel Kit
For side-by-side installation of trimmed units. This kit provides
for a unified custom grille panel to span the width of two units
using a 1/4" framed or 3/4" overlay panel.
ZPBS360, Black and ZPSS360 Stainless Steel Accessory Panel Kits
These accessory panels are cut to size and ready to install.
For answers to your Monogram,® GE Profile™
or GE® appliance questions, visit our website
at ge.com or call GE Answer Center® service,
800.626.2000.
Listed by
Underwriters
Laboratories
Specification Created 6/08
110153
ZIF360NX
GE Monogram® 36" Built-In Custom All-Freezer
Features and Benefits
• Custom Panel Model - Can be personalized with
cabinet-matching panels and handles
• Enhanced Temperature Management System - With
precise electronic controls and thermistors, maintains
ideal storage conditions for frozen foods
• Concealed Halogen Lighting System - Illuminates
contents without compromising space
• Concealed Ice Drawer - Provides quick and easy
access to filtered ice
• GE Water Filtration System - Provides clean, fresh-
tasting water to the freezer's icemaker
• ENERGY STAR® Qualification - As an ENERGY STAR
partner, GE has determined that Monogram all-
freezers meet the ENERGY STAR guidelines for energy
efficiency
• Adjustable Spillproof Glass Shelves, Gallon-Size Door
Bins and Pullout Baskets - Allow cutomizable storage
for foods and containers of varying sizes
• Model ZIF360NXRH – Custom Panel (right-handed
door swing)
• Model ZIF360NXLH – Custom Panel (left-handed
door swing)
For answers to your Monogram,® GE Profile™
or GE® appliance questions, visit our website
at ge.com or call GE Answer Center® service,
800.626.2000.
Specification Created 6/08
110153
|