GE Monogram
®
Use and Care Guide
Stainless Steel
Professional
24,″ 27,″ 36″ & 48″
Outdoor
Cooking Center
Safety Precautions
Stainless Steel Outdoor Cooking Center
FOR YOUR SAFETY
If you smell gas:
WARNING
Do not try lighting this appliance
without reading the lighting
instructions contained in this
Use and Care Guide.
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. Open lid.
4. If odor continues, immediately call
your gas supplier or your fire
department.
FOR YOUR SAFETY
1. Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
2. An LP cylinder not connected for use
shall not be stored in the vicinity of
this or any other appliance.
POUR VOTRE SÉCURITÉ
AVERTISSEMENT
Si vous sentez une odeur de gaz :
Ne pas essayer d’allumer cet appareil
sans lire les instructions d’allumage
contenues dans ce Guide d’utilisation
et d’entretien.
1. Fermer l’alimentation de gaz vers
l’appareil.
2. Éteindre toute flamme nue.
3. Ouvrir le couvercle.
4. Si l’odeur persiste, téléphoner
immédiatement à votre fournisseur
de gaz ou à votre service d’incendie.
POUR VOTRE SÉCURITÉ
1. Ne pas remiser ou utiliser de
l’essence ou autres vapeurs et
liquides inflammables près de cet
appareil ou de tout autre appareil.
2. Un cylindre de gaz propane non
relié pour l’utilisation ne doit pas
être remisé près de cet appareil ou
de tout autre appareil.
3
Consumer Information
Stainless Steel Outdoor Cooking Center
Read this guide carefully. It is intended to help If you do not understand something or need
Before
you operate and maintain your new cooking
center properly.
more help, call:
using your
cooking
center
GE Answer Center®
Keep it handy for answers to your questions.
800.626.2000
24 hours a day, 7 days a week
1.888.880.3030 in Canada.
Write
On 36″ or 48″ models you will find them on a
label in the rear of the burner box below the
burner grates.
Before sending in this card, please write these
numbers here:
down the
model &
serial
On 27″ models you will find them in the back
right corner of the cooking center.
Model Number
numbers
On 24″ models, you will find them on the
angled surface beneath the grill controls.
Serial Number
Use these numbers in any correspondence or
service calls concerning your cooking center.
These numbers are also on the Consumer
Product Ownership Registration Card
included in this guide.
Immediately contact the dealer (or builder)
that sold you the cooking center.
If you
received a
damaged
cooking
center
Before you request service, check the Problem
Solver in the back of this guide.
It lists causes of minor operating problems that
you can correct yourself.
Save time
& money
To obtain service, see the Consumer Services
page in the back of this guide.
NEXT, if you are still not pleased, write all the
details—including your phone number—to:
If you
need
service
We are proud of our service and want you to be
pleased. If for some reason you are not happy
with the service you receive, here are steps to
follow for further help.
Manager, Consumer Relations
GE Appliances
Appliance Park
Louisville, KY 40225
FIRST, contact the people who serviced your
appliance. Explain why you are not pleased.
In most cases, this will solve the problem.
4
Important Safety Instructions
Stainless Steel Outdoor Cooking Center
IMPORTANT SAFETY NOTICE
• The California Safe Drinking Water and
Toxic Enforcement Act requires the
Governor of California to publish a list of
substances known to the state to cause
cancer, birth defects or other reproductive
harm, and requires businesses to warn
customers of potential exposure to such
substances.
• Gas appliances can cause minor exposure to
four of these substances, namely benzene,
carbon monoxide, formaldehyde and soot,
caused primarily by the incomplete
combustion of natural gas or LP fuels.
Properly adjusted burners, indicated by a
bluish rather than a yellow flame, will
minimize incomplete combustion. Exposure
to these substances is minimized because this
is an outdoor unit.
SAFETY PRECAUTIONS
When using your appliance, follow basic safety • Do not try lighting this appliance without
precautions, including the following:
reading the lighting instructions in this guide.
• Be sure your appliance is properly installed
and grounded by a qualified technician in
accordance with the provided installation
instructions.
• Read this guide carefully and completely
before using your cooking center to reduce
the risk of fire, burn hazard or other injury.
Please retain this guide for future reference.
• Do not attempt to repair or replace any
part of your cooking center unless it is
specifically recommended in this guide.
All other servicing should be referred
to a qualified technician.
• This outdoor cooking gas appliance is not
intended to be installed in or on recreational
vehicles and/or boats.
• Never allow anyone to sit, stand or play on or
around the cooking center at any time. When
in use, portions of the cooking center get hot
enough to cause severe burns.
• Have the installer show you where the gas
shut-off valve is located so that you know
where to shut off the gas to the cooking center.
• Do not store items of interest to children
around or below the cooking center, in the
cart or built-in enclosure.
• If you smell gas, the installer has not done a
proper job of checking for leaks. You can have
a small leak and therefore a faint gas smell if
the connections are not completely tight.
• Never allow children to crawl inside a cart
or enclosure.
Finding a gas leak is NOT a do-it-yourself
procedure. Some leaks can only be found with
the burner control in the ON position and for
your protection it must be done by a qualified
service technician. Never use an open flame to
locate a leak.
• Never let clothing, pot holders or other
flammable materials come in contact with or
too close to any grate, burner or hot surface
until it has cooled. Fabric may ignite and
result in personal injury.
• Do not use water on grease fires. Never pick up
a flaming pan. Turn the controls off. Smother a
flaming pan on a burner by covering the pan
completely with a well-fitting lid, cookie sheet
or flat tray. Use a multi-purpose dry chemical
or foam-type fire extinguisher.
• This cooking center is for outdoor use only.
Tested in accordance with ANSI Z21.58,
Latest Edition standard for outdoor cooking
gas appliances.
• Check your local building codes for the
proper method of installation. In the absence
of local codes, this unit should be installed in
accordance with the National Fuel Gas Code
No. Z223.1, Latest Edition and the National
Electrical Code ANSI-NFPA No. 70, Latest
Edition.
Flaming grease outside a pan can be put out by
covering it with baking soda or, if available, by
using a multi-purpose dry chemical or foam-
type fire extinguisher.
5
Important Safety Instructions
Stainless Steel Outdoor Cooking Center
SAFETY PRECAUTIONS
• Use this appliance only for its intended use
• When using the range-top burners always use
flat-bottomed pans which are large enough to
cover the burner. Adjust the flame so that it
heats only the bottom of the pan to avoid
ignition of clothing. Position handles inward
away from open edges of the unit to avoid
burns associated with spillovers. Hold the
handle of the pan with a pot holder when
turning or stirring food.
as described in this guide.
• Children should not be left alone or
unattended in an area where the cooking
center is being used.
• For personal safety, wear proper apparel.
Loose fitting garments or sleeves should
never be worn while using this appliance.
Some synthetic fabrics are highly flammable
and should not be worn while cooking.
• Do not use the grill for cooking excessively
fatty meats or products which promote
flare-ups.
• Only certain types of glass, heat-proof glass
ceramic, earthenware, or other glazed
utensils are suitable for grill use. Unsuitable
types of materials may break with sudden
temperature changes. Use only on low or
medium heat settings according to the
manufacturer’s directions.
• Never grill without the drip pan in place and
pushed all the way to the back of the grill.
Without it, hot grease could leak downward
and produce a fire or explosion hazard.
• Never rotisserie cook without the basting
pan in place and pushed all the way to the
back of the grill. Without it, hot grease
could leak downward and produce a fire
or explosion hazard.
• Do not heat unopened food containers as a
build-up of pressure may cause the container
to burst.
• Use a pot holder when opening the roll top
lid. Open the lid slowly to allow heat and
steam to escape.
• Do not leave the cooking center unattended
while cooking.
• For proper lighting and performance of the
burners it is necessary to keep the ports clean.
• Use only dry pot holders—moist or damp pot
holders on hot surfaces may result in burns
from steam. Do not use a towel or other bulky • Clean the grill with caution. To avoid steam
cloth in place of a pot holder. Do not let pot
holders touch hot portions of the grill rack or
burner grates.
burns, do not use a wet sponge or cloth to
clean the grill while it is hot. Some cleaners
produce noxious fumes or can ignite if
applied to a hot surface.
• Never lean over an open grill.
• Do not operate the cooking center under
unprotected combustible construction.
Use only in well ventilated areas. Do not
use in buildings, garages, sheds, breezeways
or other such enclosed areas. This unit is for
outdoor use only.
• Pay close attention when lighting a burner.
Be certain you are rotating the igniter labeled
for the burner you intend on using.
• When using the grill, do not touch the grill
rack, burner grate or immediate surrounding
areas as these areas become extremely hot
and could cause burns. Keep children away!
• Do not locate the cooking center where
the grill exhaust is directed at combustible
materials, windows (open or closed),
doorways, etc. The grill vents combustion
gases and smoke to the back of the appliance.
• Grease is flammable. Let hot grease cool
before attempting to handle it. Avoid letting
grease deposits collect in the drip pans. Clean
the drip pans often. (On some models)
• Keep the area surrounding the cooking center
free from combustible materials, trash, or
combustible fluids and vapors such as gasoline
or charcoal lighter fluid. Do not obstruct the
flow of combustion and ventilation air.
• Do not use aluminum foil to line drip
pans or grill racks. This can severely upset
combustion air flow or trap excessive heat in
the control area. The result of this can be
melted knobs or rotary igniters.
6
SAFETY PRECAUTIONS
• At least once a year, the unit should be
• The 27˝, 36˝ and 48˝ professional grills are
designed for a single layer of lava rock to
be spread evenly over the stainless steel
radiant tray above the grill burners. To avoid
blocking off the area for the grill burners to
vent, do not use more than a single layer of
lava rock. Adding excess rock can damage
ignition components and knobs and void
the warranty.
inspected for the presence of spiders, spider
webs or other insects. The burner area is a
common and desired spider haven and can
present a dangerous condition which can
damage the cooking center and render it
unsafe for use. The presence of spiders,
spider webs or other insects can cause the gas
to flow from the front of the burner. This is a
very dangerous condition which can cause a
fire to occur behind the valve panel. Check
the cooking center immediately if any of the
following conditions exist:
• If a cart unit is stored indoors ensure
that it is cool before attempting to move it.
If LP, the cylinder must be unhooked and
the LP cylinder stored outside in a well
ventilated area, out of the reach of children.
From the caster side of the cooking center
push, never pull, the cooking center.
1. The smell of gas in conjunction with
extreme yellow tipping of the burner
flames.
2. The grill or range-top burners do not
• Never use a dented or rusty LP tank. See the
requirements in the installation instructions.
reach temperature.
3. The grill or range-top burners heat
• Never put more than one LP cylinder below
a cart-mounted cooking center. Never modify
the cart to house a larger cylinder or more
than one cylinder at a time. Do not store
spare tanks in a built-in enclosure.
unevenly.
4. The burners make popping noises.
• Do not use charcoal on the grill.
• Keep any electrical supply cord, or the
rotisserie motor away from the heated
areas of the cooking center.
• Keep the ventilation openings of the LP
cylinder enclosure free and clear from debris.
• LP units require an LP tank equipped
with a type 1 connector and an over-fill
protection device. If you use a tank
exchange system, be sure to exchange this
tank for a similarly equipped tank.
• Never use the cooking center in windy
conditions. If located in a consistently windy
area (oceanfront, mountaintop, etc.) a wind
break will be required. Always adhere to
the specified clearances listed in the
installation instructions.
• Cook meat and poultry thoroughly—meat to
at least an INTERNAL 160°F. and poultry
to at least an INTERNAL 180°F. Cooking
to these temperatures usually protects
against foodborne illness.
• The 24˝ professional grill is designed for
single rows of ceramic briquettes to be
placed in the stainless steel radiant trays
above the grill burners. To avoid blocking
off the area for the grill burners to vent, do
not place the ceramic briquettes over the
holes in the stainless steel radiant trays.
Placing the ceramic briquettes over the
holes in the stainless steel radiant trays can
damage ignition components and knobs
and void the warranty.
SAVE THESE INSTRUCTIONS
7
Features of Your Cooking Center
Stainless Steel Outdoor Cooking Center
10
11 12 13
18
19
Design
information
9
(Not all features
are on all models.
Appearance may vary
throughout this Guide.)
12
8
7
14
15
6
5
7
5
16
4
3
1
1
17
17
2
1
2
1
17
With Rotisserie
Without Rotisserie
With Rotisserie
Without Rotisserie
ZGG48L31
ZGG48N31
ZGG48L42
ZGG48N42
ZGG48L30
ZGG48N30
ZGG48L40
ZGG48N40
ZGG36L21
ZGG36N21
ZGG36L31
ZGG36N31
ZGG36L20
ZGG36N20
ZGG36L30
ZGG36N30
Feature Index
Page
16
12
11
1
2
3
4
5
6
7
Grill Control(s)
11
17
—
Rotisserie Control(s)
LP Gas Cylinder Enclosure
Drip Tray
15
20
14
17
—
7
1
2
Range-Top Burner Controls
Safety Valve Button
Lighting Instructions
(location may vary)
17
8
9
Range-Top Burners
(on some models)
14
Burner Cover
14
—
With Rotisserie
Without Rotisserie
10 Rotisserie Electrode Cover
11 Insulated Handle
ZGG27L21
ZGG27N21
ZGG27L20
ZGG27N20
—
12 Model and Serial Numbers
13 Grill Rack(s)
4, 30
9–12
11, 17, 19
16
11
14
15
13
14 Roll Top Lid
15 Rotisserie Motor Assembly
16 Smoker System
19
17 Smoker Control
19
1
7
18 Rotisserie Basting Pan
19 LP Tank (on some models)
17
10
12
With Rotisserie
Grill covers are available from our Parts and Accessories.
Call 800.626.2002
ZGG24L20
8
The Grill
Stainless Steel Outdoor Cooking Center
The grill section consists of a large cast iron
burner or burners (depending on model), a
series of stainless steel heat baffles (on some
models), a bed of natural lava rocks or ceramic
briquettes and a porcelain enameled heat
retaining grill rack(s).
General
information
Grill rack
Lava rocks
Each burner is rated at 15,000 BTU for
24″models.
Each burner is rated at 20,000 BTU for
27,″ 36″ and 48″ models.
Stainless steel
radiant tray
Below each burner is a stainless steel heat
baffle (on some models) which reflects usable
heat upward into the cooking area and reduces
the temperature of the drip pan below (on
some models).
Burner
The cast iron grill burner encompasses the
entire cooking area and is top ported to
operate cooler and last longer.
Heat baffle
On some models, the burners in the cooking
area are side ported.
Ceramic
briquettes and
stainless steel
radiant trays
(on 24″
Above the burner(s) is a stainless steel radiant
tray(s) which supports the lava rock or ceramic
briquettes and protects the grill burner ports
from blockage.
models)
Burners
(on 24″
models)
9
The Grill
Stainless Steel Outdoor Cooking Center
The grill is supplied with natural lava rock
(on some models). Because of the porosity of
natural lava rock it is superior in its ability to
capture heat as it rises from the grill burners.
It also possesses the thermal mass needed for
professional results. Flare-ups are controlled
because the lava radiant keeps grease from
getting to the flames and igniting.
Place lava rocks in a single layer on top of the
stainless steel radiant tray located under the
grill rack. It is important to distribute the rocks
evenly over the tray without leaving any large
gaps. Uneven distribution of the rocks and air
gaps can cause localized “hot” and “cold” spots
which could result in unsatisfactory cooking
performance.
Lava rock
(on some models)
The intense heat produced by this system
produces true grilled flavor as fats and juices
are brought to the surface of the food and
caramelized.
The intense radiant heat from the ceramic
briquettes caramelizes the fats and juices that
are brought to the surface of the food, giving it (See the Rotisserie section for placement when
racks. The small tray is to be placed in the back
and the large tray is to be placed in the front.
Ceramic
briquettes
(on some models)
the barbecued flavor.
rotisserie cooking.)
The ceramic briquettes are in two separate
stainless steel trays located under the grill
Make sure the briquettes are in place in the trays
so that they do not cover the holes in the trays.
WARNING: IMPORTANT!
Before
lighting
the grill
Inspect the gas supply piping or hose prior to
turning the gas on. If there is evidence of cuts,
wear or abrasion, it must be replaced prior to
use. Any replacement pressure regulators or
hose assembly must be the type specified by
the manufacturer.
If the grill uses LP gas, connect the regulator to
the LP tank and check the hose and regulator
connections for leaks with a soap and water
solution before operating the grill.
Keep a spray bottle of soapy water near the gas
supply valve and check the connections for gas
leaks before each use.
For LP use, the pressure regulator and hose
assembly supplied with the unit must be used.
Turn all knobs to OFF then turn on the gas
supply.
This LP tank is equipped with overfill
protection. When you refill or trade in your
tank, make sure the one you receive also has
overfill protection.
Do not use the grill if the odor of gas is present.
AVERTISSEMENT : IMPORTANT!
Si le gril utilise du gaz propane, connecter le
régulateur au réservoir de gaz propane et
vérifier les connexions du tuyau et du
régulateur pour les fuites, avec une solution
de savon et d’eau avant de faire fonctionner
le gril.
Inspecter la canalisation d’alimentation de gaz
ou le tuyau avant d’allumer le gaz. S’il existe
un indice de coupure, usure ou abrasion, cette
canalisation doit être remplacée avant
l’utilisation de l’appareil. Tous les régulateurs
de pression ou montage de tuyau de
Garder une bouteille de vaporisation d’eau
remplacement doivent être du type spécifié par savonneuse près du robinet d’alimentation de
le fabricant.
gaz et vérifier les connexions pour les fuites de
gaz avant chaque utilisation.
Pour l’utilisation avec le gaz propane, le
régulateur de pression et le montage de tuyau
fournis avec l’appareil doivent être utilisés.
Tourner tous les boutons à OFF (ARRÊT)
ensuite ouvrir l’approvisionnement de gaz.
Ce réservoir de gaz propane est muni d’un
dispositif de protection contre le remplissage
excessif. Lorsque vous remplissez de nouveau
ou échangez votre réservoir, s’assurer que celui
que vous recevez a aussi une protection contre
le remplissage excessif.
Ne pas utiliser le gril s’il existe une odeur
de gaz.
10
Always keep your face and body as far away from the
grill as possible when lighting.
Make sure that the match is adjacent to the
burner ports. (On 24″ models, open the lid
and use the lighting hole on the left top
edge.)Push and turn the control knob, which is
centered on the burner you wish to light, to
LITE. If the burner does not light in 4 seconds
turn the knob OFF. Wait 5 minutes and try
again. If the burner will not light after several
attempts, see the Problem Solver in the back of
this guide.
To light
the grill
Open the lid, push and turn the grill control
knob to the LITE position and immediately
turn the rotary igniter knob of the spark igniter
next to the grill control knob. You will hear a
snapping sound. At the same time a spark will
be provided at the grill burner.
It may be necessary to turn the rotary igniter
knob several times until the burner is lit.
If the burner does not light in 4 seconds,
turn both knobs to OFF and wait 5 minutes,
for any accumulated gas to dissipate, before
trying again.
NOTE:
• Do not attempt to light the grill if the odor
of gas is present. Call for service.
• Always wait 5 minutes before relighting a
hot grill.
If the burner will not light after several
attempts the burner can be match lit. Remove
the grill rack over the burner(s) you wish to
light. If you’ve just attempted to light the
burner with the igniter, allow 5 minutes for any
accumulated gas to dissipate. Keep your face as
far away from the grill as possible and pass a lit,
long stem match through the lava radiant tray
and position it near the burner ports.
Grill control knob
Bouton de commande
Rotary igniter knob
Bouton d’allumage
rotatif
Toujours garder le visage et le corps aussi loin que possible
du gril lors de l’allumage.
Allumage
du gril
Each grill burner has its own rotary igniter.
Chaque brûleur du gril a son propre allumeur rotatif
Ouvrir le couvercle, appuyer et tourner le bouton
de commande du gril à la position LITE (allumage)
et tourner immédiatement le bouton d’allumage
rotatif de l’allumeur à étincelle, près du bouton de
commande du gril. Un bruit sec se fait entendre. En
même temps, une étincelle sera fournie au brûleur
du gril.
Match lighting hole
on 24″ models
Trou d’allumage
sur les modèles de
24 pouces
Il peut être nécessaire de tourner le bouton
d’allumage rotatif plusieurs fois jusqu’au moment
où le brûleur s’allume. Si le brûleur ne s’allume pas
en moins de 4 secondes, tourner les deux boutons à
OFF (arrêt) et attendre 5 minutes pour que tout le
gaz accumulé se dissipe, avant d’essayer de nouveau
l’allumage.
que vous désirez allumer, à la position LITE
(allumage). Si le brûleur ne s’allume pas en quatre
secondes, tourner le bouton à OFF (arrêt).
Attendre 5 minutes et essayer de nouveau. Si le
brûleur ne s’allume pas après plusieurs essais, voir
la solution pour résoudre le problème au verso de
ce guide.
Si le brûleur ne s’allume pas après plusieurs essais,
le brûleur peut être allumé par une allumette.
Enlever la grille du gril au dessus du (des)
brûleur(s) que vous désirez allumer. Si vous venez
juste d’essayer d’allumer le brûleur avec l’allumeur,
attendre 5 minutes pour que tout le gaz accumulé se
dissipe. Garder votre visage aussi loin que possible
du gril et passer une longue allumette allumée à
travers le plateau radiant de lave et la placer près
des orifices du brûleur. S’assurer que l’allumette
soit adjacente aux orifices du brûleur. (Sur les
modèles de 24 pouces, ouvrir le couvercle et utiliser
le sur le bord supérieur à gauche.) Appuyer et
tourner le bouton de commande, vis-à-vis le brûleur
REMARQUE :
• Ne pas essayer d’allumer le gril si une odeur de gaz
existe. Faire venir le service d’entretien.
• Toujours attendre 5 minutes avant de réallumer un
gril chaud.
11
The Grill
Stainless Steel Outdoor Cooking Center
Grilling requires high heat for searing and
proper browning. Most foods are cooked at the
HI heat setting for the entire cooking time.
However, when grilling large pieces of meat or
poultry, it may be necessary to turn the heat to
a lower setting after the initial browning. This
cooks the food through without burning the
outside.
1. Check to be certain the drip tray is in place.
Using the
grill
2. Light the grill using the instructions in the
To light the grill section of this guide.
3. Turn the control knob to HI and preheat the
grill for 10–15 minutes. The roll top lid is to
be closed during preheating.
4. Place the food on the grill and cook to the
desired doneness. The control knob may be
set to any position to adjust the heat setting
if necessary.
Foods cooked for a long time or basted with a
sugary marinade may need a lower heat setting
near the end of the cooking time.
Do not leave the grill unattended while
cooking.
NOTE: The hot grill sears the food, sealing in
the juices. The longer you preheat the grill, the
faster the meat browns and the darker the grill
marks will be.
• When turning the meat over, always use a
spatula as it will not puncture the meat
allowing the juices to run out. This will help to
keep the meat juicy. Turn the meat only once,
as juices are lost when the meat is repeatedly
turned. Season or salt the meat after it has
been cooked; these procedures have a
tendency to dry the meat out.
• The U. S. Department of Agriculture says,
“Rare beef is popular, but you should know
that cooking it to only 140°F. means some
food poisoning organisms may survive.”
(Source: Safe Food Book. Your Kitchen
Guide. USDA Rev. June 1985.)
Grilling
hints
• When defrosting meats it is recommended
that it be done overnight in the refrigerator
as opposed to a microwave. This in general
yields a juicier cut of meat.
• Be sure to trim any excess fat from meat or
poultry. To prevent steaks or chops from
curling while they are being cooked, slit the
fat around the edges at about 2-inch intervals.
To test for doneness, make a small cut in the
center of the meat.
• Always ensure that the meat is thoroughly
cooked by using a meat thermometer.
• The doneness of meat is affected by the
thickness of the cut. It is impossible to cook a
thin piece of meat to a rare doneness. A steak
should be at least 1-inch thick to have it turn
out rare and juicy. The cooking time is
affected by the temperature of the meat
when you start to cook it, the size and shape
of the cut and the kind of meat you are
cooking. The degree of doneness desired
also affects the time.
12
This is a suggested guide only. There are many variables that will affect cooking performance. These include
wind, temperature, humidity and cut of meat.
Grilling
guide
Weight/
Flame
Size
Approximate
Time
Food
Thickness
Comments
Fresh Vegetables
Beets, carrots, turnips
Medium
12 to 20 min.
Slice. Dot with butter or margarine.
Wrap in heavy duty foil.
Turn occasionally.
Onion
1/2″ slices
Medium
Medium
High
8 to 20 min.
40 to 60 min.
45 to 60 min.
Brush occasionally with melted
butter or margarine. Turn once.
Sweet potatoes
White potatoes
Whole
Wrap individually in heavy
duty foil. Rotate occasionally.
6 to 8
ounces
Wrap individually in heavy
duty foil. Rotate occasionally.
Frozen Vegetables
Asparagus, broccoli,
brussels sprouts, green
beans, peas
Medium
15 to 30 min.
Dot with butter or margarine and a
small amount of water. Wrap in
heavy duty foil. Turn occasionally.
Beef
Hamburgers
1/2″ to 3/4″ Medium
10 to 18 min.
6 to 15 min.
Turn once when juices rise to the
surface. Do not leave unattended.
A flare-up could occur.
High
Steaks—rare (140°)
1″
High
High
Medium
to High
Medium
Medium
8 to 14 min.
11 to 18 min.
12 to 22 min.
16 to 27 min.
18 to 30 min.
16 to 35 min.
Remove excess fat from edge.
Slash remaining fat at 2″ intervals.
Turn once.
1
1 ⁄2
″
Steaks—medium (160°)
Steaks—well done (170°)
1″
1
1 ⁄2
″
1″
1
1 ⁄2
″
Lamb Chops/Steaks
Rare (140°)
1″
High
High
Medium
to High
Medium
10 to 15 min.
14 to 18 min.
13 to 20 min.
18 to 25 min.
17 to 30 min.
Remove excess fat from edge.
Slash remaining fat at 2″ intervals.
Turn once.
1
1 ⁄2
″
Medium (160°)
1″
1
1 ⁄2
″
Well done (170°)
1″
Pork
Chops
1″
Medium
Medium
15 to 40 min.
25 to 60 min.
Remove excess fat from edge.
Slash remaining fat at 2″ intervals.
Turn once. Cook well done.
1
1 ⁄2
″
Ribs
Medium
40 to 60 min.
Turn occasionally. During the last
few minutes, brush with barbecue
sauce, turn several times.
Precooked ham steaks
Hot dogs
1/2″
High
4 to 8 min.
Remove excess fat from edge. Slash
remaining fat at 2″intervals. Turn once.
Medium
5 to 10 min.
Slit skin. Turn once.
Poultry
Broiler fryer, halved
or quartered
1
2 to 3 lbs.
Low
Medium
1 to 1 ⁄2 hours
Place skin side up. Turn frequently
brushing with melted butter,
margarine, oil or marinade.
40 to 60 min.
30 to 45 min.
8 to 15 min.
12 to 20 min.
Breasts
Medium
Fish and Seafood
Steaks: halibut,
salmon, swordfish
3/4″ to 1″
Low to
Medium
Turn once. Brush with melted butter,
margarine or oil to keep moist.
Whole catfish,
rainbow trout
4 to 8 ounces
Low to
Medium
Turn once. Brush with melted butter,
margarine or oil to keep moist.
13
Range-Top Burners
Stainless Steel Outdoor Cooking Center
Some cooking centers are equipped with heavy
cast iron burners. Each is rated at 15,000 BTU
and has a rotary spark igniter for efficient lighting.
Range-top
burners
(on some models)
The burner grates are porcelain enamel over
cast iron for durability.
Each cooking center comes with a stainless steel
cover which doubles as a work surface. When
using the grill burners with the work surface in
place, be careful as heat can conduct from the
grill section and cause the work surface to heat up.
Never attempt to light the range-top burners
with the work surface in place.
Cover the range-top burners with the stainless
steel cover when not in use.
First remove the burner cover, by lifting up and
to the side, or any cooking utensils from the
burner grate.
To light a
range-top
burner
CAUTION: The burner cover may be hot if the
grill burners are in operation.
(on some models)
MISE EN GARDE : Le couvercle du brûleur
peut être chaud si les brûleurs du gril sont en
fonctionnement.
If the burner will not light after several
attempts, wait 5 minutes. The burner can
be lit by holding a lit match next to the
burner ports and turning the control
knob to LITE.
Push and turn the control knob to the LITE
position and immediately turn the rotary igniter
knob (between the rear and front burner
knobs) until the burner is lit or 4 seconds pass.
If the burner doesn’t ignite wait 5 minutes for
any accumulated gas to dissipate then try again.
Correct
Incorrect
The correct height of the flame depends on the
size and material of the pan being used, the
food being cooked and how much liquid is in
the pan.
Flame
height
• The flame should never extend beyond the
bottom of the pan.
• Pans that conduct heat slowly (such as glass-
ceramic) should be used with low or medium
flame unless you are cooking with a large
amount of liquid.
Note: The flame size on a gas burner should match the
cookware you are using.
14
The rotisserie system is designed to cook items
from the back of the grill using infrared heat.
The rotisserie burner (on some models) is an
infrared type which provides intense searing
radiant heat. This intense heat is magnificent
for searing in the natural juices and nutrients
found in quality cuts of meat.
Rotisserie
system
The rotisserie motor is equipped with metal
gears and is capable of turning up to a 12, 15
or 20 lb. cut of meat or poultry, depending on
the model. The actual capacity is limited by
clearance and motor torque.
(on some models)
Once lit, the rotisserie burner will reach cooking
temperatures in about 1 minute. The orange/red
glow will even out in about 5 minutes.
Maximum 24″ model . . . . . . . . . . . . . 12 lb. turkey
Maximum 27″ model . . . . . . . . . . . . . 15 lb. turkey
Maximum 36″, 48 ″ models . . . . . . . . . 20 lb. turkey
WARNING: Electrical Grounding Instructions
This appliance rotisserie motor is equipped
with a three-prong (grounding) plug for your
The rotisserie motor must be electrically
grounded in accordance with local codes or,
protection against shock hazard and should be in the absence of local codes, with the National
plugged directly into a properly grounded
three-prong receptacle. Do not cut or remove
the grounding prong from the plug.
Electrical Code, ANSI/NFPA 70-1990.
If an extension cord is required to operate the
rotisserie motor, use only a grounded cord
approved for outdoor use. Use as short of cord
as possible and avoid wet areas.
AVERTISSEMENT : Instructions de mise à la terre électrique
Ce moteur de la rôtisserie de l’appareil est
muni d’une fiche à trois broches (mise à la
terre) pour votre protection contre le risque
de choc et doit être branché directement dans
une prise de courant à trois alvéoles dûment
reliée à la terre. Ne pas couper ni enlever de
la fiche la broche de liaison à la terre.
Si une rallonge est requise pour faire
fonctionner le moteur de la rôtisserie,
utiliser un cordon relié à la terre et approuvé
pour utilisation en plein air. Utiliser un
cordon aussi court que possible et éviter les
endroits mouillés.
Le moteur de la rôtisserie doit être relié à la
terre électriquement conformément aux codes
locaux ou, à défaut de codes locaux, selon le
Code électrique national, ANSI/NFPA 70-1990.
15
The Rotisserie System
Stainless Steel Outdoor Cooking Center
On 24″ models the motor is mounted by sliding
it down into place in the metal channel attached
to the right side of the grill. The skewer is
connected to the motor assembly by placing
the pointed end through the motor access hole
in the grill and into the motor. The left side of
the skewer rests in the grill groove.
Assembly
On 27″ models the motor is mounted to a metal
channel which attaches to the left side of the
grill and is tightened into place with a thumb
screw. Ensure that the motor is straight prior to
tightening the thumb screw.
24″ model rotisserie assembly
The rotisserie motor on 36″ and 48″ models is
secured down to a cast rotisserie block with the
black screw-down knob. The rotisserie block is
in turn bolted to the right side panel.
On 36″ and 48″ models, the skewer or the
rotisserie is attached to the motor assembly by
placing the pointed end into the motor and
resting the threaded end on the support at the
left side (right side on 24″ and 27″ models) of
the grill.
With the skewer pushed as far as possible into
the motor, the grooved skewer bushing should
rest on the left side bracket.
27″ model rotisserie assembly
The removable black handle should only be in
place when handling the skewer. Remove the
handle when cooking to allow the lid to close
and avoid melting the handle with heat from
the range-top burners (on some models).
36″ and 48″ model rotisserie assembly
16
1. Open the lid.
To setup the
grill for
2. Remove the grill racks.
3. Remove the front large stainless steel
rotisserie
radiant tray with briquettes.
(24″models only)
4. Remove the back small stainless steel radiant
tray with briquettes and place it into the
rotisserie cooking position by sliding it into
the rotisserie cooking slots.
5. Place the basting pan, on the grill floor,
inside the grill compartment, against the
bottom of the stainless steel radiant tray.
Basting Pan
24″ model rotisserie
6. Assemble the rotisserie motor and skewer.
7. Use only the small, stainless steel radiant
tray with briquettes in the rotisserie cooking
position. The large stainless steel radiant
tray with briquettes is not used during
rotisserie cooking.
7. Use the REAR GRILL control only, for
rotisserie cooking.
The location of the burner allows the
placement of the rotisserie basting pan
(included) beneath the food to collect
juices and drippings for basting and gravy.
To flavor the contents of the basting pan, you
can add herbs, onion, garlic or spices. Hams
are especially good with the addition of
pineapple slices and brown sugar to the
basting pan.
Basting
pan
1. To load the skewer begin with the handle in
place and slide one of the meat holders, with
the prongs facing away from the handle,
onto the skewer.
4. Tighten the wing nuts with pliers. It may be
necessary to wrap the food with butcher’s
string to secure any loose portions. Never
use nylon or plastic string.
To load the
skewer
2. Push the skewer through the center of the
food, then slide the second meat holder with
the prongs toward the food, onto the skewer.
5. Once the food is secure, insert the skewer
into the motor. If needed, remove the grill
racks. Place the basting pan beneath the
food. It is normal for the skewer to flex
when larger cuts of meat are being cooked.
3. Center the food on the skewer. Push the meat
holders firmly together. (Some models have
grooves on the skewer to indicate the burner 6. Use the motor switch (on some models) to
position. Use them to position the meat
holders.) When cooking foods such as multiple
chickens, always place the thickest portion
of the food nearer the center of the skewer.
turn the rotisserie motor on or off.
17
The Rotisserie System
Stainless Steel Outdoor Cooking Center
Open the lid. Push the control knob to the
LITE position.
To light the
rotisserie
burner
Press the safety valve button, hold in, and
begin turning the rotary ignitor button located
next to the control knob. It may be necessary to
turn the ignitor knob several times until the
burner lights. You will hear a snapping sound.
At the same time, a spark will be provided at
the safety probe. Once the burner ignites, hold
the safety valve button in for about 10 seconds
or until the burner remains lit.
(on some models)
NOTE: The location of the rotisserie burner
makes it susceptible to strong wind conditions,
more so than the protected grill burners.
For this reason you should avoid utilizing the
rotisserie burner during windy conditions.
As an added precaution we’ve equipped the
burner with an automatic safety valve which
will not allow gas to flow to the rotisserie
burner unless the following conditions are
present with the knob on:
This is the only burner on the grill with a safety
valve. Once lit, turn the control knob to the
desired setting.
If the burner does not light within 4 seconds,
release the safety valve button and turn the
control knob to OFF.
If the ignitor does not function, the burner can
be lit by holding a lit match to the burner (with
the control knob at LITE and the safety valve
button pressed).
1. The safety valve button is pressed.
2. The safety probe is sufficiently heated to
Wait 5 minutes before relighting a hot
rotisserie burner.
open the valve.
Food
Setting
Med. High
High
Approx. Time
40 minutes
50 minutes
To help you in planning your rotisserie
cooking, these are representative cooking
times. Refer to a cookbook for suggested
marinade and menu ideas.
Cooking
times
Large chicken thighs/kabobs
Rack of spare ribs
12–15 lb. Turkey
10 lb. Pork roast
High
3 hours
1
2
High
1 ⁄ –2 hours
8–12 Lamb chops
Med. High
20–25 minutes
18
The Smoker System
Stainless Steel Outdoor Cooking Center
Tiles
For the 27″ models, the smoke flavor tray is
located directly beneath the rotisserie burner.
It is a stainless steel tray which is designed to
hold wood chips or herbs for adding a smoke
flavor to foods.
Rotisserie
burner
The smoke
flavor tray
(on some models)
For the 36″ and 48″ models, the smoke flavor
tray is located above a 5,000 BTU burner. The
burner is controlled by a precision brass valve
which is capable of being turned down to very
low heat levels. The smoker system may be used
alone for low temperature roasting and
smoking or in conjunction with any
Smoke flavor tray
Because of the location of the smoke flavor tray on 27″ models,
the rotisserie burner acts as the burner for the smoke flavor tray.
Smoke flavor tray (36″ and 48″ models)
combination of other burners.
The tray may also be filled with water to
produce steam. Whether smoking or steaming
the lid should remain closed as much as
possible to maximize the effect.
There are many wood chips available for
purchase and selection is based on personal
taste. The most common wood chips used are
mesquite or hickory. Mesquite has a sweeter
taste and is commonly used with poultry and
seafood. Hickory is best suited for red meats.
Use of oak, cherry, maple, aspen or apple is
also common while aromatic herbs like sage,
bay leaves, thyme or basil may also be of use.
If the wood chips do flame up, add a small
amount of water to extinguish the flame. This
should be done carefully through the top of
the grill area, or by pulling the tray out slightly.
Wood chips
To avoid steam burns, use caution when
adding water to a hot tray. Never completely
remove a hot tray.
During extended roasting periods it is normal
to add fresh wood chips to the tray several
times.
Always soak the chips in water prior to putting
them into the tray. In the beginning you may
want to use the HI position to start the chips
smoking, then reduce the heat to a lower level
to prevent them from drying out and flaming.
To minimize the possibility of burns do not
remove the smoker tray when hot.
Open the lid and remove the smoker tray. Locate
the burner visually by looking through the cut-
out in the valve panel. Push and turn the control
knob to the LITE position and immediately
turn the smoker rotary ignitor knob (for 36″ or
48″ cooking centers) or the rotisserie rotary
ignitor knob (for the 27″ cooking centers) until
the burner is lit or 4 seconds pass. If the burner
doesn’t ignite, wait 5 minutes for any accumulated
gas to dissipate, then try again. If the burner will
not light after several attempts, wait 5 minutes
then match light using a long stemmed match
or lighter through the cut-out in the valve panel.
Once lit, fill the smoker tray and replace.
To light the
smoker burner
(on some models)
On 36″ and 48″ cooking centers
When using the smoker system in conjunction
with the optional infrared rotisserie burner
you’ll find it helpful to use the low setting of the
smoker burner to minimize the heat rising up to
the rotisserie basting pan. Staggering the meat
away from the smoker burner also helps.
On 27″ cooking centers
19
Care and Cleaning
Stainless Steel Outdoor Cooking Center
The easiest way to clean the grill is immediately For harder baked-on food particles, remove the
Grill rack(s)
after cooking is completed and after turning
off the flame. Wear a barbeque mitt to protect
your hand from the heat and steam. Dip a
brass bristle barbeque brush in tap water and
scrub the hot grill. Drip the brush frequently in
the bowl of water. Steam, created as water
contacts the hot grill, assists the cleaning
process by softening any food particles. The
food particles will fall onto the hot lava rocks
or ceramic briquettes and burn or fall into the
drip tray (on some models). If the grill is
allowed to cool before cleaning, cleaning will
be more difficult.
grill rack and soak for about one hour in warm
water. Lightly scrub with a Scotch Brite® pad.
The full width drip trays will collect grease from Allow the pan and its contents to cool before
Drip trays
(on some models)
the grill section as well as boilovers and spills
from the range-top burners (on some models).
attempting to clean. Clean the grease from the
pan often to avoid the possibility of a grease fire.
It is not necessary to remove the lava rocks for
cleaning. They burn themselves clean during
the next cooking operation. Periodically the
rocks need to be turned over for a thorough
cleaning. How often you use the grill and the
amount and type of food cooked will determine
when it is necessary to turn the lava rocks.
If grease can be seen on the top of the rocks
or if you get a lot of flare-ups during cooking,
the rocks need to be turned over and heated
on HIGH for about 30 minutes, longer for
heavy soil.
Lava rocks
(on some models)
The layer of ceramic briquettes, under the grill
rack(s), will last for many years with proper care. may occur as they may get brittle with age,
Chipping or cracking of the briquettes
Ceramic
briquettes
(on some models)
depending on the frequency of use. This is
normal and does not affect the performance.
Burned-on food particles and ash can be
emptied off the stainless steel radiant trays
when cool by shaking over a waste receptacle.
Do not replace the stainless steel radiant trays
with alternates. Should the ceramic briquettes
ever need to be replaced, purchase them
locally, wherever outdoor cooking centers
are sold.
After emptying the ash from the trays, replace
them with the small tray in the back and the
large tray in the front. Make sure the briquettes
do not cover the holes in the tray.
20
The range-top burner grates are porcelain
enamel over cast iron for durability. To avoid
burns do not clean a hot grate. They may be
wiped while in place with hot, soapy water,
rinsed and wiped dry. Never immerse a hot
grate in water.
Burner
grates
(on some models)
Due to rapid temperature changes the
porcelain may pop off the edges of the grates.
Do not be concerned as the base metal, cast
iron, soon darkens to blend with the porcelain
enamel. Use care when wiping areas where the
enamel has popped off. The edges may be sharp.
If you remove the grates for cleaning, care should be taken
in lifting them. They are very heavy. Place the grates on a
protected surface.
Do not use a steel wool pad; it will scratch the
stainless steel surface.
For hard to clean soil, or film layers of grease,
use a stainless steel cleaner such as Bon-Ami®.
Apply cleaner with a damp sponge, rinse
thoroughly and dry. Always scrub lightly in
the direction of the grain.
Stainless
steel
Inside and outside stainless steel can be
cleaned easily and quickly with a stainless steel
cleaner such as Revere Copper and Stainless
Steel Cleaner®.
Before replacing an igniter perform this
simple test.
If there is a spark, examine the wire of the
electrode for cracks and cuts. Also examine
the electrode for grease and debris or see if the
electrode tip is bent. Is the tip sparking to the
top of the electrode bracket?
Replacing
a rotary
igniter
1. Remove the drip tray (on some models).
2. From underneath the valve panel, look
upwards and locate the end of the igniter
wire, where it is connected. Disconnect the
wire and place the metal blade of a
screwdriver about 1/8″ from the terminal
of the rotary igniter.
The rotary igniter may be replaced from the
front by removing the drip pan (on some
models) and reaching behind the valve panel
to unplug the igniter wire. Remove the igniter
knob and the two mounting screws. (Reverse
the procedure to replace.) If removing the
valve panel is necessary begin by removing all
the control knobs, then remove the 4 corner
screws of the valve panel.
3. Turn the igniter knob. If the igniter is good,
a spark will jump across to the screwdriver.
If there is no spark, replace the igniter.
Spiders and insects can nest in the burners or
orifices of this or any outdoor gas appliance.
The presence of spiders, spider webs or other
insects can cause the gas to flow from the
front of the burner. This is a very dangerous
condition which can cause a fire to occur
behind the valve panel, damaging the cooking
center and making it unsafe for use.
You should inspect the burners at least once a
year or immediately if any of the following
conditions occur:
Spider and
insect
warning
1. The smell of gas in conjunction with the
burner flames appearing yellow.
2. The grill or range-top burners do not reach
temperature.
3. The grill or range-top burners heat unevenly.
4. The burners make popping noises.
If blockage exists, clean the burners immediately.
21
Care and Cleaning
Stainless Steel Outdoor Cooking Center
Ensure the gas supply is off, the knobs are in the
OFF position and all surfaces are cool before
removing a burner.
Burner
removal
(on some models)
Flash tubes
Venturi tube
The grill and range-top burners are cast iron
coated with porcelain enamel. Occasionally
it will be necessary to remove surface rust to
ensure proper performance. Frequency of
cleaning will depend on the climate and
location and how often you use the cooking
center. The walls of the burners are thick so
they can withstand many years of use.
Lighter
ports
Igniter
Burner hanger
Air shutters
To remove the grill burner(s), remove the grill
rack(s), then lift out the stainless steel radiant
tray(s) with the lava rocks or ceramic briquettes
still on it. Remove wire shipping ties if present.
Grasp the burner, pull it up and slightly to the
rear of the unit so the burner head comes off
the brass orifice at the front. Angle the burner
sideways and remove.(24″ models have two
grill burners.)
Range-top burner
To remove the range-top burners (on some
models), remove the top grates. Lift out
aeration pan from around the burners. Lift and
remove the front and rear range-top burners.
Grill burner for 27,″ 36″ and 48″ models
The smoker burner (on some models) can be
removed and cleaned by unplugging the igniter
wire and lifting out the burner.
To reassemble the burners, replace the burner
by sliding the air shutters over the brass orifice,
centering it in the hole. It is extremely important
to center the burner on the orifice properly.
Be careful not to upset the air shutters’ original
position (unless readjusting). Lower the rear
of the burner into the cutouts on the support
channel and make sure the locating hole in the
burner end is seated over the pin in the burner
box. Make sure all burners are level and do
not rock.
Grill burners for 24″ model
On 24″ models, to double check if the two
burners are properly seated over the brass
orifices, you can visually inspect them.
Replace the stainless steel radiant tray so that
the slots in the corners of the tray align with
the projections on the top of the burner. (On
24″ models the stainless steel radiant trays sit
level on the side supports.) Make sure that it
sits level and does not rock.
1. Remove the two outer control knobs.
2. Remove the two screws underneath the
control knobs and the two screws underneath
the control panel.
Light all of the burners and check for proper
flame characteristics. (Do not attempt to light
the burners prior to replacing radiant trays,
grills and aeration pans.) If adjustments are
necessary refer to the Installation Instructions.
3. Rotate the control panel forward. (Do not
remove it.)
4. Shine a flashlight in the gap to make sure the
burners are over the brass orifices. Replace
screws and knobs.
22
Keep the rotisserie motor electric cord away
from the heated surface of the grill. When not
in use remove and store the motor in a dry
location.
Rotisserie
Clean the skewer in warm sudsy water.
Clean the exterior of the burner(s) with a wire
brush.
Burner
cleaning
Be sure burner ports are clear and free from
debris. Clear any clogged ports with a
straightened paper clip. Never use a wooden
toothpick as it may break off and clog the port.
Never enlarge the burner ports. Shake out any
debris through the air shutter.
Grill burner for 27,″ 36″ and 48″ models
Use a flashlight to inspect the burner inlet to
ensure it is not blocked. If obstructions can be
seen, use a metal wire coat hanger that has been
straightened out to clear them.
NOTE: To ensure warranty coverage and proper
performance of the grill and range-top burners,
monthly inspection and cleaning of all the grill
and range-top burner orifices is recommended.
Grill burners for 24″ model
With the burner(s) removed, remove the
orifice and shine a flashlight through the
opening to ensure there is no blockage.
Use a needle to clear any debris. Be extremely
careful not to enlarge the hole or break off
the needle.
Orifice
cleaning
Clean up spatters with a damp cloth. Remove
heavier soil with warm, soapy water.
Control
panel and
knobs
Do not use abrasives of any kind on the control
panel.
The control knobs may be removed for easier
cleaning. To remove a knob, pull it straight off
the stem. Wash the knobs in soap and water but
do not soak.
23
The Problem Solver
Stainless Steel Outdoor Cooking Center
PROBLEM
POSSIBLE CAUSE
Questions?
Use this
problem
solver!
GRILL WON’T LIGHT •Check to see if other burners on the unit operate.
WHEN THE ROTARY
IGNITER IS TURNED
•Remove the grill rack and the stainless steel radiant tray, and watch
the igniter tip. You should see a spark jump from the tip of the igniter
when the knob is turned. If there is no spark check to ensure there is
gas supplied to the unit.
•Use a match to light the burner. (See the “To light the grill” section).
•Visually check the electrode and wire while turning the igniter.
The only place a spark should appear is at the electrode tip.
If the electrode or wire leaks voltage, remove and replace.
•Purge the gas line of any air.
•Check the orifice for blockage.
•Inspect the igniter tip to make sure it is clean and free from debris.
Clean the area. Readjust for 1/8″ gap.
BURNER FLAME IS
YELLOW OR ORANGE
IN CONJUNCTION
WITH THE ODOR
OF GAS
•Check the burner inlet for obstructions.
•Check the air shutter for proper adjustment.
(See the “Installation Instructions”).
•Placement of the cooking center is important for proper burner
operation. Do not place the cooking center in a dusty area.
LOW HEAT WITH
CONTROL KNOB IN
THE HI POSITION
•Inspect the fuel hose to ensure it is not bent or kinked.
•Adequate gas supply may not be available. Check to make sure there
is gas in the LP tank (on some models).
•If it is only one burner that appears low, the burner or burner orifice
may need cleaning.
•The air shutter may need adjustment.
•Preheat the grill for 15 minutes with the lid closed.
ROTISSERIE BURNER •Check for a spark at the igniter.
WON’T LIGHT
(on some models)
•Use a match to light the burner.
OPTIONAL
•Readjust the thermocouple so that it is not bent or kinked, but
lies flat against the burner.
ROTISSERIE LIGHTS
BUT WILL NOT HOLD
FLAME ONCE
•Hold the safety valve button in until the burner remains lit.
BUTTON IS RELEASED
(on some models)
24
Notes
Stainless Steel Outdoor Cooking Center
25
Notes
Stainless Steel Outdoor Cooking Center
26
27
Consumer Services
Stainless Steel Outdoor Cooking Center
With the purchase of your new Monogram appliance, receive the
assurance that if you ever need information or assistance from GE,
we’ll be there. All you have to do is call—toll- free!
Whatever your question about any Monogram major appliance, GE Answer Center®
information service is available to help. Your call—and your question—will be answered
promptly and courteously. And you can call any time. GE Answer Center® service is open
24 hours a day, 7 days a week.
GE Answer
Center®
In the USA:
800.626.2000
In Canada, call 1.888.880.3030.
A GE consumer service professional will provide expert repair service, scheduled at a time
that’s convenient for you. Many GE Consumer Service company-operated locations offer
you service today or tomorrow, or at your convenience (7:00 a.m. to 7:00 p.m. weekdays,
9:00 a.m. to 2:00 p.m. Saturdays). Our factory-trained technicians know your appliance
inside and out—so most repairs can be handled in just one visit.
In-Home Repair
Service
In the USA:
800.444.1845
In Canada:
1.888.880.3030
GE offers, free of charge, a brochure to assist in planning a
barrier-free kitchen for persons with limited mobility.
For Customers
With Special
Needs…
Consumers with impaired hearing or speech who have access to a
TDD or a conventional teletypewriter may call 800-TDD-GEAC
(800-833-4322) to request information or service.
In the USA:
800.626.2000
You can have the secure feeling that GE Consumer Service will still be there after your
warranty expires. Purchase a GE contract while your warranty is still in effect and you’ll
receive a substantial discount. With a multiple-year contract, you’re assured of future
service at today’s prices.
Service Contracts
In the USA:
800.626.2224
In Canada:
1.888.880.3030
Individuals qualified to service their own appliances can have parts or accessories sent directly
to their home. The GE parts system provides access to over 47,000 parts…and all GE Genuine
Renewal Parts are fully warranted. VISA, MasterCard and Discover cards are accepted.
Parts and
Accessories
User maintenance instructions contained in this guide cover procedures intended to be
performed by any user. Other servicing generally should be referred to qualified service
personnel. Caution must be exercised, since improper servicing may cause unsafe operation.
In the USA:
800.626.2002
In Canada:
1.888.880.3030
28
o d a y M a i l T
I m p o r t a n t
e g i s t r a t i o n O w n e r s h i p
C o n s u m e r P
G E A p p l i a n c e s
Place
1st Class
Letter
Stamp
Here
General Electric Company
Warranty Registration Department
P.O. Box 34070
Louisville, KY 40232-4070
29
Consumer Product Ownership Registration
Dear Customer:
Thank you for purchasing our product and thank you for placing your confidence in us. We are proud to
have you as a customer!
Follow these three steps to protect your new appliance investment:
Complete and mail
your Consumer
After completing this
registration, write your
Read your “Use and Care
Guide” carefully. It will
help you operate your new
appliance properly. If you
have questions, or need
more information call
Product Ownership
Registration today.
Have the peace of mind
of knowing we can
contact you in the
unlikely event of a
model and serial numbers
in this guide. You will
need this information
should you require
service. Our service
the GE Answer Center
®
number is 800-444-1845.
800.626.2000.
1
safety modification.
2 3
Important: To ensure that your product is registered, fold and mail this form. No envelope is needed.
Consumer Product Ownership Registration
Product
Model
Serial
Outdoor Cooking Center
Mr. l Ms. l Mrs. l Miss l
First
Name
Last
Name
Street
Address
Apt. #
Zip
Code
City
State
Date Placed
In Use
Month
Phone
Number
Day
Year
GE Appliances
General Electric Company
Louisville, Kentucky 40225
CUT HERE
30
Warranty for customers in Canada
Stainless Steel Outdoor Cooking Center
YOUR MONOGRAM OUTDOOR COOKING CENTER WARRANTY
Staple sales slip or cancelled check here. Proof of original purchase
date is needed to obtain service under warranty.
FULL ONE-YEAR WARRANTY
WHAT IS
COVERED
For one year from date of original purchase, we will provide, free of charge, parts and service
labor in your home to repair or replace any part of the cooking center that fails because of a
manufacturing defect.
LIMITED FIVE-YEAR WARRANTY
For five years from the date of original purchase, we will provide, free of charge,
replacement cast iron burners, stainless steel radiant tray, upper and lower heat shields, grill
racks and drip pans if they fail in normal use. You pay for the service trip to your home and
all service labor charges.
This warranty is extended to the original purchaser and any succeeding owner for products
purchased for ordinary home use in Canada.
All warranty service will be provided by our Factory Service Centers or by our authorized
Customer Care® servicers during normal working hours.
Should your appliance need service, during warranty period or beyond, call 1.888.880.3030.
• Service trips to your home to teach you how • Failure of the product if it is used for other
WHAT IS NOT
COVERED
to use the product.
than its intended purpose or used
commercially.
Read your Use and Care material.
• Improper installation.
If you then have any questions about
operating the product, please contact your
dealer or our Consumer Affairs office at
the address below, or call, toll free:
1.888.880.3030
• Replacement of rotary igniters.
If you have an installation problem, contact
your dealer or installer. You are responsible
for providing adequate electrical, gas,
exhausting and other connecting facilities
as described in the Installation Instructions
provided with the product.
• Chipping of porcelain enamel grates or
burners.
WARRANTOR IS NOT RESPONSIBLE
FOR CONSEQUENTIAL DAMAGES.
• Replacement of house fuses or resetting of
circuit breakers.
• Damage to the product caused by accident,
fire, floods or acts of God.
Some provinces do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you. This warranty gives
you specific legal rights, and you may also have other rights which vary from province to
province. To know what your legal rights are in your province, consult your local or
provincial consumer affairs office.
Warrantor: Camco, Inc. If further help is needed concerning this warranty, write: Manager—
Consumer Relations, Inc., 1 Factory Lane, Suite 310, Moncton, N.B. E1C 9M3.
31
Warranty for customers in the USA
Stainless Steel Outdoor Cooking Center
YOUR MONOGRAM OUTDOOR COOKING CENTER WARRANTY
Staple sales slip or cancelled check here. Proof of original purchase
date is needed to obtain service under warranty.
FULL ONE-YEAR WARRANTY
WHAT IS
COVERED
For one year from date of original purchase, we will provide, free of charge, parts and service
labor in your home to repair or replace any part of the cooking center that fails because of a
manufacturing defect.
LIMITED FIVE-YEAR WARRANTY
For five years from the date of original purchase, we will provide, free of charge,
replacement cast iron burners, stainless steel radiant tray, upper and lower heat shields, grill
racks and drip pans if they fail in normal use. You pay for the service trip to your home and
all service labor charges.
This warranty is extended to the original purchaser and any succeeding owner for products
purchased for ordinary home use in the 48 mainland states, Hawaii and Washington, D.C. In
Alaska the warranty is the same except that it is LIMITED because you must pay to ship the
product to the service shop or for the service technician’s travel costs to your home.
All warranty service will be provided by our Factory Service Centers or by our authorized
Customer Care® servicers during normal working hours.
Should your appliance need service, during warranty period or beyond, call 800-444-1845.
• Service trips to your home to teach you how • Damage to the product caused by accident,
WHAT IS NOT
COVERED
to use the product.
fire, floods or acts of God.
Read your Use and Care material.
• Failure of the product if it is used for other
than its intended purpose or used
commercially.
If you then have any questions about
operating the product, please contact your
dealer or our Consumer Affairs office at
the address below, or call, toll free:
GE Answer Center®
800.626.2000
consumer information service
• Replacement of rotary igniters.
• Chipping of porcelain enamel grates or
burners.
• Improper installation.
If you have an installation problem, contact
your dealer or installer. You are responsible
for providing adequate electrical, gas,
exhausting and other connecting facilities
as described in the Installation Instructions
provided with the product.
WARRANTOR IS NOT RESPONSIBLE
FOR CONSEQUENTIAL DAMAGES.
• Replacement of house fuses or resetting of
circuit breakers.
Some states do not allow the exclusion or limitation of incidental or consequential damages,
so the above limitation or exclusion may not apply to you. This warranty gives you specific
legal rights, and you may also have other rights which vary from state to state.
To know what your legal rights are in your state, consult your local or state consumer affairs
office or your state’s Attorney General.
Warrantor: General Electric Company. If further help is needed concerning this warranty,
write: Manager—Consumer Affairs, GE Appliances, Louisville, KY 40225
ZGG24L20
ZGG27L20
ZGG27N20
ZGG27L21
ZGG27N21
ZGG36L20
ZGG36N20
ZGG36L21
ZGG36N21
ZGG36L30
ZGG36N30
ZGG36L31
ZGG36N31
ZGG48L30
ZGG48N30
ZGG48L31
ZGG48N31
ZGG48L40
ZGG48N40
ZGG48L42
ZGG48N42
10600-01RV.2
Monogram®
Part No. 164D3333P192
Pub No. 49-8965-1
9-99 JR
General Electric Company
Louisville, KY 40225
Printed in the United States
|