Extron electronic Universal Remote KP 6 User Manual

User’s Guide  
KP 6 Keypad Remote  
Keypad Remote Controls  
68-694-01 Rev. A  
Printed in the USA  
07 02  
 
Installation and Operation  
Pin  
1
Contact closure Function  
Wire color  
Brown  
Introduction  
In#1  
Input #1  
The KP 6 is designed to control MSW 4 Series, SW AV Series (4 and 6  
input models only), SW VGA/Ars Series, and SW RGBHV/ A Series  
switchers, or other Extron products with contact closure ports or  
ports labeled as “Remote.”  
2
Not used  
Not used  
1
5
3
4
In#2  
Gnd  
In#3  
In#4  
In#5  
In#6  
Input #2  
Red  
5
Signal ground Black  
The KP 6 is a contact closure remote for selecting the switcher’s input.  
When a number key is pressed, the wire associated with that input is  
momentarily shorted to ground, making the switcher switch to that  
input.  
6
Male  
9
6
Input #3  
Input #4  
Input #5  
Input #6  
Orange  
Yellow  
Green  
Blue  
7
8
9
The KP 6 can control up to 6 inputs and requires no power.  
Figure 2 — 9-pin Sub-D connector pinout  
Installation  
Installation with a captive screw connector  
Installation with a 9-pin D-sub connector  
Some switchers, such as the MSW 4 Series, are not equipped with  
9-pin D-sub connectors and have a 3.5mm, 5-pole captive screw  
connector (labeled “Contact”) instead. In order to use the KP 6  
Keypad Remote Control with these switchers, a captive screw  
connector (included with the switcher) must be used. To use a captive  
screw connector, the existing 9-pin D-sub connector must be removed  
from the cable and a captive screw connector installed.  
Many switchers, such as the SW6 VGA Ars Switcher, come equipped  
with a 9-pin D-sub connector. To use the KP 6 Keypad Remote  
Control on this type of switcher, install it as follows:  
1.  
2.  
Power down the switcher.  
Connect the KP 6 adapter’s 9-pin plug to the contact closure  
connector on the switcher’s rear panel.  
To install the captive screw connector, remove the wire from the 9-pin  
D-sub connector, then strip the wires and insert them into the new  
connector (supplied with the switcher). Wire the connector as shown  
here. Tighten the screws to secure the wires. Clip off the green and  
blue wires.  
3.  
4.  
Position the KP 6 Keypad for the most convenient operation.  
Power up the switcher.  
25 foot  
cable  
Do not tin the stripped wire leads before installing the  
captive screw connector. Tinned wires are not as secure  
in the captive screw connectors and could pull out.  
100-240V 0.2A  
REMOTE  
OUTPUT  
INPUTS  
3
SW6VGAArs  
OUTPUT  
1
2
5
4
6
L
R
50-60Hz  
Install the KP 6 Keypad Remote Control on this type of switcher as  
follows:  
SW6 VGA Ars Switcher  
1.  
2.  
3.  
Rewire the connector on the KP 6 Keypad Remote Control.  
Power down the switcher.  
3
4
1
2
KP 6 Keypad  
Remote Control  
Connect the KP 6 adapter’s captive screw connector to the  
“Contact” connector on the switcher’s rear panel.  
4.  
5.  
Position the KP 6 Keypad for the most convenient operation.  
Power up the switcher.  
Figure 1 — Typical KP 6 application (with 9-pin D-  
sub connector)  
2
Keypad Remote Controls • Installation and Operation  
Keypad Remote Controls • Installation and Operation  
3
 

Electro Voice Microphone PL91 User Manual
Excalibur electronic Video Games 908 EFG User Manual
Extron electronic Network Cables 26 672 06 User Manual
FieldServer Computer Drive FS 8704 13 User Manual
Fusion Marine GPS System MS AV600 User Manual
Garmin GPS Receiver 1210 User Manual
GE Dust Collector MM300 User Manual
Gemini Stereo System XL 500II User Manual
GE Monogram Computer Monitor JV535H User Manual
GE Range ZGU364LD User Manual