PAPER SHREDDER
Personal Series
DESTRUCTEUR DE DOCUMENTS
Série usage personnel
DESTRUCTORA DE DOCUMENTOS
Serie de uso personal
MODELS / MODÈLES / MODELOS
S70C-2, P600C-2
USE AND CARE MANUAL
MANUEL D’EMPLOI ET D’ENTRETIEN
MODO DE EMPLEO Y DE CUIDADO
PLEASE READ AND SAVE THIS MANUAL WITH YOUR ORIGINAL RECEIPT
Customer Service: 1-800-955-0959
VEUILLEZ LIRE CE MANUEL ET LE CONSERVER AVEC LE TALON D’ACHAT
Service clientèle (Canada) : 1-800-665-4339
POR FAVOR, LEA Y GUARDE ESTE MANUAL CON EL RECIBO ORIGINAL
Dpto. de Atención al Cliente: 1-800-955-0959
IMPORTANT SAFEGUARDS
PARTS OF THE SHREDDER
A
C
• NEVER insert hands or fingers into paper entry as serious personal
injury may result.
D
• THIS MACHINE IS NOT A TOY. Keep children and pets away from
shredder AT ALL TIMES as serious injury may result. Always unplug
shredder when not in use.
• Keep loose objects (jewelry, ties, long hair) away from shredder.
These items and others like them may cause serious injury if they
accidentally fall into the paper entry.
E
B
F
• Confetti cut shredders contain sharp edges on the underside of the
machine. Use caution when positioning the shredder head onto the
basket.
• Do not exceed recommended sheet capacity.
• Do not shred plastic, continuous forms, adhesive labels, transparen-
cies, newsprint, or cardboard.
A. Paper entry
B. Basket
C. Auto-start sensor
D. Power switch
E. Shredder head
F. Viewer
• This personal shredder is intended for paper only. Do not attempt
to shred paper clips or other hard materials (except staples).
• Do not place shredder near or over a heat source or water.
• Always turn off and unplug unit before moving or cleaning and
when not in use.
• Do not insert aerosol cleaners into or around the shredder. Some
agents may combust, causing serious injury.
• Never use flammable synthetic oil, petroleum-based or aerosol
lubricants to oil the cutting blades. Some agents may combust,
causing serious injury. Use only a recommended oil in a non-
aerosol container. See "MAINTENANCE."
ASSEMBLY
NOTE: This shredder will operate only when used with the supplied
basket. The supplied basket has a built-in safety feature which pre-
vents the shredder from operating if used with any other basket or if
improperly assembled.
To assemble shredder:
• Do not use this product if it or the cord has been damaged in any
way.
• Do not open the cover for any reason. Doing so can expose you to
dangerous voltages and will void your warranty.
These shredders contain sharp edges on the
underside of the shredder head. Use caution
when positioning the shredder head onto the basket.
1. Position shredder head over basket as shown in Figure 1.
2. Align slot on back of shredder head with the tab on the inside rear
of the basket.
Power Cord Care
• Place power cord in an easily accessible position, because it is the
main disconnect switch.
• Do not place machine where adults, children or animals may walk
on the cord.
3. Lower shredder head onto basket (while maintaining tab/slot
alignment).
• Do not rest anything on the power cord.
• If an extension cord is used, be sure that all products plugged into
the extension cord do not exceed the extension cord ampere rat-
ing.
REAR VIEW
Figure 1
2
Cool-Down Cycle
OPERATION
This shredder is protected with a special safety feature which prevents
the motor from overheating with extensive use. When shredding is
attempted beyond the machine's maximum running time, the
shredder will automatically shut off its motor until it has cooled
to an acceptable operating level. This is normal and the shredder
will return to operation after the “cool-down” period. See “Product
Usage Guide” (page 1) for maximum running time and related cool-
ing or “off” time.
This product features an auto-start sensor. This
sensor will turn on the cutting blades whenever
anything is inserted into the paper entry (while the power switch is in
the AUTO (I) position). For the safety of pets and children, we rec-
ommend always moving the power switch to OFF (O) and unplugging
whenever the shredder is unattended or not in use.
1. Assemble shredder (see "ASSEMBLY").
2. Remove any paper clips or other foreign objects (except staples)
from paper. If folding paper to fit paper entry, adjust sheet capaci-
ty appropriately.
Do not attempt to shred paper clips or other hard
materials (except staples) with this machine.
Extensive use of paper clips or other hard materials will result in dam-
age to the cutting system and will void the manufacturer's warranty.
3. Be sure power switch is in OFF (O) position. Plug shredder into
proper power supply outlet.
Clearing a Jam
If the shredder sheet capacity is exceeded or paper is not put in
straight, a jam may result. See “Product Usage Guide” (page 1) for
maximum sheet capacity for your shredder. In the case of a jam, the
machine will “bog down” and fail to shred the paper.
To clear a jam:
1. Move the power switch to the REVERSE (R) position. (If waste bas-
ket is full, empty it before clearing jam.) The shredder will reverse
the paper to clear the jam.
2. If the shredder jams in reverse, move the power switch to AUTO
(I) and allow to run for about five seconds. If jam does not clear,
move power switch to REVERSE (R) again and allow to run for
about five seconds. Repeat this procedure until the jam is cleared.
If necessary, use care to grasp the paper carefully and pull out to
clear the jam.
4. Move power switch to AUTO (I) position. To clear the cutting
blades, the shredder will "run" for about 1 second immediately
after switching to AUTO (I). When the unit is turned on and in
standby mode, the shredder is ready to be fed paper through the
paper entry.
NEVER insert hands or fingers into
paper entry as serious personal injury may result.
Do not exceed recommended sheet capacity (see
"Product Usage Guide" on page 1).
3. Once the jam is cleared, move the power switch to AUTO (I) for
continued shredding or OFF (O) if shredding is complete.
5. Slide paper straight into paper entry until the shredder automati-
cally begins shredding.
The shredder automatically stops a few seconds after shredding is
complete.
Continue shredding as desired to a MAXIMUM shredding time
of 5-7 minutes. At this time, the machine MUST be allowed to
"cool down" for a MINIMUM of 15 minutes. (See "Cool-Down
Cycle" for more information.)
If the shredder jams or shuts off before the maximum shredding
time, see "Clearing a Jam" section for further instructions.
6. Move power switch to OFF (O) position when shredding is com-
plete.
MAINTENANCE
Confetti cut shredders require regular (monthly) oiling of the cutting
blades to maintain proper operation. Failure to oil the blades regu-
larly could result in reduced sheet capacity performance, excessive
noise during operation, paper jams and possibly shredder failure.
We recommend using only Powershred Lubricant #35250
(available by contacting Fellowes) or a vegetable-based oil
(such as corn or canola) in a non-aerosol container with an
extension nozzle.
Never use flammable synthetic oil, petroleum-
7. Unplug power cord from outlet whenever shredder is unattended
or not in use.
8. Look through viewer to see if basket is full. If full, remove shred-
der head and empty basket contents. Replace shredder head onto
basket.
based, or aerosol lubricants to oil the cutting
blades. Some agents may combust, causing seri-
ous injury.
To oil the cutting blades:
1. From the top of the shredder, squeeze the recommended lubricant
across the full width of the blades.
2. Move the power switch to AUTO (I) position and allow the blades
to run at least 3 seconds.
3. Move the power switch to REVERSE (R) position and allow it to
run for at least 3 seconds.
4. Repeat steps 2-3 above at least 3 times.
3
TROUBLESHOOTING
LIMITED WARRANTY
Fellowes Manufacturing Company (the “Company”) warrants the cut-
ting cylinders of the machine to be free from defects in material and
workmanship for 3 years from the date of purchase by the original
consumer. Fellowes warrants all other parts of the machine to be free
of defects in material and workmanship for 1 year from the date of
purchase by the original consumer. If any part is found to be defec-
tive during the warrant period, your sole and exclusive remedy will
be repair or replacement, at Fellowes’ option and expense, of the
defective part.
Shredder will not
operate.
a. Shredder is not plugged in.
b. Power switch is in the OFF (O) position.
Move switch to AUTO (I) position.
c. Shredder is jammed. See "Clearing a
Jam" section.
d. Shredder has exceeded the maximum
run time and requires a "cool-down"
time. See "Product Usage Guide" (page
1).
e. Shredder is not assembled properly.
See "Assembly."
This warranty does not apply in cases of abuse, mishandling or unau-
thorized repair. ANY IMPLIED WARRANTY, INCLUDING THAT OF MER-
CHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY
LIMITED IN DURATION TO THE APPROPRIATE WARRANTY PERIOD SET
FORTH ABOVE. In no event shall Fellowes be liable for any consequen-
tial or incidental damages attributable to this product. This warranty
gives you specific legal rights. You may have other legal rights that
vary from state to state.
Shredder makes a
loud squeaking or
rubbing noise.
Cutting blades need to be oiled
REGULARLY.
See "MAINTENANCE" section.
Shredder suddenly
stops while
shredding.
a. Shredder has exceeded the maximum
run time and requires a "cool-down"
time. See "Product Usage Guide" (page
1).
For more detail or to obtain service under this warranty, please con-
tact Fellowes Customer Service at 1-800-955-0959, Monday through
Friday, 8 AM - 5 PM (Central Standard Time).
b. Shredder is jammed. See "OPERATION -
Clearing a Jam."
For specific instructions on obtaining service under this warranty on
machines purchased outside the USA, contact the appropriate location
listed in the Contact for Service section of this instruction manual.
Shredder shreds less
than capacity.
Cutting blades need to be oiled
REGULARLY.
See "MAINTENANCE" section.
Warrantor: Fellowes, Inc.
Shredder operates
only in REVERSE.
A small piece of paper may be blocking the
auto-start sensor of this shredder. Move the
power switch to the OFF (O) position and
unplug the shredder. Turn shredder over
and use a toothpick (from the underside
of the unit) to clear the paper blockage at
the auto-start sensor (center) location.
Shredder runs contin-
uously when in
AUTO.
A small piece of paper may be causing the
auto-start feature to run continuously. Move
the power switch to the OFF (O) position and
unplug the shredder. Use a toothpick
(from the top of the unit) to clear the
paper blockage at the auto-start sensor
(center) location.
Shredder runs for a
few seconds after
the paper has cleared
the cutters.
This is normal. The shredder runs a few sec-
onds longer than the paper in order to keep
the cutters clear of paper particles and reduce
the chances of a jam.
4
Contact For Service
Vos Contacts Fellowes
Sus Contactos Fellowes
United States
Canada
Australia
1-800-955-0959
1-800-665-4339
1-800-33-11-77
1789 Norwood Avenue • Itasca, Illinois 60143-1095
630-893-1600
®
Australia
Benelux
Canada
France
Germany
Italy
Japan
Poland
United Kingdom
Doncaster, S. Yorks.
Tullamarine, Vic
Vianen, NL
Markham, Ont.
Rennes, I-V
Garbsen, Han.
Camerano, AN
Tokyo
Warsaw
© 2001 Fellowes. Printed in China. Form No. 30108
|