Fujitsu LifeBook
N Series
BIOS Guide
LifeBook N Series Models:
N3530
Document Date: 03/28/2006
Document Part Number: FPC58-1486-01
F U J I T S U C O M P U T E R S Y S T E M S
1
B I O S S e t u p U t i l i t y
3. If an error message is displayed on the screen, and
you want to enter the setup utility, press the [F2] key.
4. When the setup utility starts with a fault present, the
system displays the following message:
Warning!
Error message
[Continue]
5. Press any key to enter the setup utility. The system
will then display the Main Menu with current
parameters values.
3
L i f e B o o k
N
S e r i e s N o t e b o o k B I O S
INFORMATION MENU - DISPLAYS BASIC SYSTEM INFORMATION
The Information menu is a display-only screen that
provides the configuration information for your note-
book.
The information, including CPU type and
speed, and total memory, displayed on this
screen varies according to the unit you
purchased.
The following table shows the names of the menu fields
for the Information menu and the information
displayed in those fields. These fields are for information
purposes only, and cannot be modified by the user.
InsydeH20 Setup Utility
Information
System
BIOS Version:
BIOS Date:
BIOS Area:
1.09
03/13/2006
E000h - FFFFh
CPU
Genuine Intel(R) CPU
L1 Cache RAM:
L2 Cache RAM:
T2300 @ 1.66GHz
128 KB
2048 KB
Memory
Total:
Slot 1:
Slot 2:
512 MB DDR2
512 MB DDR2
None
Up/Dn Select Boot Device
<>
Select Screen
Select Item
Asset Number:
None
Enter Select
F1 = Help
Submenu
F9 = Setup Defaults
F10 = Save and Exit
Esc = Exit
Figure 1. Information Menu
Table 1: Fields, Options and Defaults for the Information Menu
Note that the parameters listed in the following table may be different, depending upon the system configuration.
Menu Field
BIOS Version:
BIOS Date:
BIOS Area:
CPU:
Default
Menu Field
L2 Cache RAM:
Total (Memory):
Slot 1:
Default
1.XX
2048 KB
01/XX/2006
E000h – FFFFh
512 MB DDR2
512 MB DDR2
None
Genuine Intel(R) CPU T2300 @ 1.66GHz Slot 2:
128 KB Asset Number:
L1 Cache RAM:
None
4
M a i n M e n u
MAIN MENU – SETTING STANDARD SYSTEM PARAMETERS
The Main Menu allows you to set or view the current
system parameters. (See Navigating Through The Setup
Utility on page 2 for more information.)
the field’s function and any special information needed
to help understand the field’s use.
System Time and System Date can also be
set from your operating system without
using the setup utility. Use the Date and
Time icon on your Windows Control panel
or type time or date from the MS-DOS
prompt.
The following tables show the names of the menu fields
for the Main menu and its submenus, all of the options
for each field, the default settings and a description of
InsydeH20 Setup Utility
Information
Main
Advanced
Security
Boot
Exit
Adjust calendar clock.
System Time:
System Date:
[14:57:01]
[03/28/2006]
<Pg Up> and <Pg Dn>
keys increase and
decrease setting.
Drive0
<Auto>
[FUJITSU MHV2100BH
Drive1
[DV-W28EAD
]
Press <Tab> to change
next item.
<Auto>
]
Language:
<English>
Up/Dn Select Boot Device
<>
Select Screen
Select Item
Enter Select
F1 = Help
Submenu
F9 = Setup Defaults
F10 = Save and Exit
Esc = Exit
Figure 2. Main Menu
Table 2: Fields, Options and Defaults for the Main Menu
Note that the parameters listed in the following table may vary depending upon your system’s configuration.
Menu Field
Options
Default
Description
System Time:
–—
–—
Sets and displays the current time. Time is in a 24 hour format
of hours:minutes:seconds with 2 digits for each. (HH:MM:SS). Example: 16:45:57.
You may change each segment of the time separately. Move between the seg-
ments with the [Tab] key. Change the setting using the Page Up and Page Down
buttons.
System Date:
–—
–—
Sets and displays the current date. Date is in a month/day/year numeric format
with 2 digits each for month and day and 4 digits for year. (MM/DD/YYYY) for
example: 03/20/1998. You may change each segment of the date separately.
Move between the segments with the [Tab] key. Change the setting using the
page Up and Page Down buttons.
5
L i f e B o o k
N
S e r i e s N o t e b o o k B I O S
Table 2: Fields, Options and Defaults for the Main Menu
Note that the parameters listed in the following table may vary depending upon your system’s configuration.
Menu Field
Options
Default
Description
■
Drive0
Auto
Disabled
[Auto]
{Auto] automatically selects the Drive0 ATA/ATAPI device type. To change the
selection, press the [Enter] key to display the selections. Select [Auto] to have the
type automatically configured by the BIOS at POST. Select [Disabled] if you don’t
want to select a primary master.
■
■
Drive1
Auto
Disabled
[Auto]
{Auto] automatically selects the Drive1 ATA/ATAPI device type. To change the
selection, press the [Enter] key to display the selections. Select [Auto] to have the
type automatically configured by the BIOS at POST. Select [Disabled] if you don’t
want to select a primary master.
■
Language:
[English]
The default setting is English.
___
Exiting from Main Menu
When you have finished setting the parameters on this menu, you can either exit from the setup utility, or move to
another menu. If you wish to exit from the setup utility, press the [Esc] key or use the cursor keys to go to the Exit
menu. If you wish to move to another menu, use the cursor keys.
6
A d v a n c e d M e n u
ADVANCED MENU – SETTING DEVICE FEATURE CONTROLS
The Advanced Menu allows you to:
(See Navigating Through The Setup Utility on page 2 for
more information.)
■
Set the keyboard Numlock feature.
Select between the display panel and an external
■
The following tables show the names of the menu fields
for the Advanced Menu and its submenus, all of the
options for each field, the default settings and a descrip-
tion of the field’s function and any special information
needed to help understand the field’s use.
CRT display or video projector.
Enable or disable compensation for your display.
Enables or disables the internal controllers.
Configure CPU and USB features in your system.
■
■
■
InsydeH20 Setup Utility
Advanced Security Boot
Information
Main
Exit
Keyboard Numlock
Video Features
<Disabled>
Selects Power-On State
for Numlock.
Internal Device Configurations
CPU Features
USB Features
Miscellaneous Configurations
Event Logging Menu
Up/Dn Select Boot Device
<>
Select Screen
Select Item
Enter Select
F1 = Help
Submenu
F9 = Setup Defaults
F10 = Save and Exit
Esc = Exit
Figure 3. Advanced Menu
Table 3: Fields, Options and Defaults for the Advanced Menu
Note that the parameters listed in the following table may vary depending upon your system’s configuration.
Menu Field
Options
Default
Description
■
Keyboard Numlock
Disabled
Enabled
[Disabled]
When enabled or disabled, turns NumLock on and off, respectively.
■
Video Features
–—
–—
–—
–—
When selected, opens the Video Features submenu, which allows setting of
the display parameters, including routing of video signals to different displays.
Internal Device
Configurations
When selected, opens the Internal Device Configuration submenu, which
allows enabling or disabling the Serial ATA, IDE, and WLAN Controllers.
7
L i f e B o o k
N
S e r i e s N o t e b o o k B I O S
Table 3: Fields, Options and Defaults for the Advanced Menu
Note that the parameters listed in the following table may vary depending upon your system’s configuration.
Menu Field
Options
Default
Description
CPU Features
–—
–—
When selected, opens the CPU Features submenu to allow you to enable or
disable the Core Multi-Processing feature and XD Bit functionality.
USB Features
–—
–—
–—
–—
–—
–—
When selected, opens the USB Features submenu to allow you to enable or
disable the legacy support and SCSI SubClass support (e.g., floppy disk drive,
external optical drive).
Miscellaneous
Configurations
When selected, opens the Miscellaneous Configurations submenu to allow you
to enable or disable the power button and the Wake Up On LAN and USBfea-
tures, and to set the System Beep.
Event Logging Menu
When selected, opens the event logging submenu.
8
A d v a n c e d M e n u
Video Features Submenu of the Advanced Menu
The Video Features Submenu is for setting the display parameters.
InsydeH20 Setup Utility
Information
Main
Advanced
Security
Boot
Exit
Select Display Terminal.
[Video Features]
*This setting is not
effective after
operating system starts
up.
Display:
Compensation:
<Auto>
<Enabled>
Up/Dn Select Boot Device
<>
Select Screen
Select Item
Enter Select
F1 = Help
Submenu
F9 = Setup Defaults
F10 = Save and Exit
Esc = Exit
Figure 4. Video Features Submenu
Table 4: Fields, Options and Defaults for the Video Features Submenu of the Advanced Menu
Menu Field
Options
Default
Description
■
Display:
Auto
Internal Flat Panel
External
[Auto]
Selects where the video signal will be routed.
Note: The Windows video driver overrides this setting.
■
■
■
■
Compensation:
Disabled
Enabled
[Enabled]
Enables or disables compensation which controls spacing on the
display. When enabled, displays with less than pixel resolution
1024 x 768 or 800 x 600 will still cover the entire screen. A resolu-
tion below 800 x 600 will fill the screen, but due to the low resolu-
tion, will appear blocky and may not be acceptable.
9
L i f e B o o k
N
S e r i e s N o t e b o o k B I O S
Internal Device Configurations Submenu of the Advanced Menu
The Internal Device Configuration submenu allows the user to configure other internal devices.
InsydeH20 Setup Utility
Information
Main
Advanced
Security
Boot
Exit
[Disabled]
[Internal Device Configurations]
Serial ATA port is
disabled.
Serial ATA Controller:
AHCI Configuration:
IDE Controller:
<Enabled>
<Enabled>
<Enabled>
[Enabled]
Serial ATA port is
enabled.
Up/Dn Select Boot Device
<>
Select Screen
Select Item
Enter Select
F1 = Help
Submenu
F9 = Setup Defaults
F10 = Save and Exit
Esc = Exit
Figure 5. Internal Device Configuration Submenu
Table 5: Fields, Options and Defaults for the Internal Device Configuration Submenu of the Advanced Menu
Menu Field
Options
Default
Description
■
Serial ATA Controller:
Disabled
Enabled
[Enabled]
Enables or disables the Serial ATA port.
■
■
AHCI Configuration:
IDE Controller:
Disabled
Enabled
[Enabled]
[Enabled]
Enables or disables the AHCI (Advanced Host Controller Interface).
Enables or disables selected IDE devices.
■
■
Disabled
Enabled
■
10
A d v a n c e d M e n u
CPU Features Submenu of the Advanced Menu
The CPU Features Submenu provides options for enabling or disabling the SpeedStep® Technology feature.
InsydeH20 Setup Utility
Information
Main
Advanced
Security
Boot
Exit
Select Core
[CPU Features]
Multi-Processing
enabled or disabled.
Core Multi-Processing:
XD Bit functionality:
<Enabled>
<Enabled>
Up/Dn Select Boot Device
<>
Select Screen
Select Item
Enter Select
F1 = Help
Submenu
F9 = Setup Defaults
F10 = Save and Exit
Esc = Exit
Figure 6. CPU Features Submenu
Table 6: Fields, Options and Defaults for the CPU Features Submenu of the Advanced Menu
Menu Field
Options
Default
Description
Core Multi-
Processing
• Disabled
• Enabled
[Enabled]
Enables or disables the multi-processing functionality of
the Core processor.
XD Bit
functionality:
[Enabled]
• Disabled
• Enabled
Allows the user to enable and disable the Execute
Disable Bit functionality. Execute Disable Bit allows the
processor to classify areas in memory where application
code can and cannot execute. In the event an internet
worm attempts to insert code in the buffer, the processor
disables code execution to prevent damage or worm
propagation.
11
L i f e B o o k
N
S e r i e s N o t e b o o k B I O S
USB Features Submenu of the Advanced Menu
The USB Features Submenu provides options for enabling or disabling legacy USB support.
InsydeH20 Setup Utility
Information
Main
Advanced
Security
Boot
Exit
[Disabled]
[USB Features]
The feature is
disabled.
Legacy USB Support:
<Enabled>
SCSI SubClass Support: <Enabled>
[Enabled]
Legacy USB Emulation is
enabled and USB devices
are available without
USB aware OS.
Up/Dn Select Boot Device
<>
Select Screen
Select Item
Enter Select
F1 = Help
Submenu
F9 = Setup Defaults
F10 = Save and Exit
Esc = Exit
Figure 7. USB Features Submenu
Table 7: Fields, Options and Defaults for the USB Features Submenu of the Advanced Menu
Menu Field
Options
Default
Description
■
Legacy USB Support:
Disabled
Enabled
[Enabled] When Enabled is selected, Legacy USB Emulation is enabled
and the USB devices are available without a USB-aware OS.
When Disabled is selected, Legacy USB support is disabled.
■
■
■
SCSI SubClass Support:
Disabled
Enabled
[Enabled] When Enabled is selected, USB devices that belong to the
SCSI subclass in the mass storage class (e.g., USB Memory
Key) are enabled. Note that enabling this feature may cause
the system to hang during POST, depending on the device
that is connected.
12
A d v a n c e d M e n u
Miscellaneous Configurations Submenu of the Advanced Menu
The Miscellaneous Configurations Submenu provides options for enabling or disabling the power button and the
Wake Up On LAN or USB features, and for setting the System Beep.
InsydeH20 Setup Utility
Information
Main
Advanced
Security
Boot
Exit
Configures the power
button.
[Miscellaneous Configurations]
*ACPI OS ignores this
setting.
Power Button:
<Disabled>
<Disabled>
<Disabled>
<Enabled>
Wake up on LAN:
Wake up on USB Device:
System Beep:
Up/Dn Select Boot Device
<>
Select Screen
Select Item
Enter Select
F1 = Help
Submenu
F9 = Setup Defaults
F10 = Save and Exit
Esc = Exit
Figure 8. Miscellaneous Configurations Submenu
Table 8: Fields, Options and Defaults for the Miscellaneous Configurations Submenu of the Advanced Menu
Menu Field
Options
Default
Description
■
Power Button:
Disabled
Enabled
[Disabled]
Selecting Disabled disables the power button. Selecting Enabled
allows you to turn off system power with the power button.
■
■
Wake up on LAN:
Wake up on USB Device:
System Beep:
Disabled
Enabled
[Disabled]
[Disabled]
[Enabled]
Selecting Enabled allows the system to wake up when the internal
LAN device receives a specific signal while in power-off state.
Selecting Disabled disables this feature.
■
■
Disabled
Enabled
Selecting Enabled allows the system to be awakened from Standby
mode by a USB device on a specific port. Selecting Disabled disables
this feature.
■
■
Disabled
Enabled
Allows you to set or disable the system beep. This item is enabled by
default.
■
13
L i f e B o o k
N
S e r i e s N o t e b o o k B I O S
Event Logging Submenu of the Advanced Menu
The Event Logging Submenu configures event logging features for DMI events.
InsydeH20 Setup Utility
Information
Main
Advanced
Security
Boot
Exit
Press <Enter> key to
view the Contents of
the Event Log.
[Event Logging Menu]
Event Log Capacity:
Event Log Validity:
Space Available
Valid
View Event Log:
<Enter>
Event Logging:
<Enabled>
System Boot Event:
<Disabled>
<No>
Clear All Event Logs:
Mark Events as Read:
Up/Dn Select Boot Device
<Enter>
<>
Select Screen
Select Item
Enter Select
F1 = Help
Submenu
F9 = Setup Defaults
F10 = Save and Exit
Esc = Exit
Figure 9. Event Logging Submenu
Table 9: Fields, Options and Defaults for the Event Logging Submenu of the Advanced Menu
Menu Field
Options
Default
Space Available
Valid
Description
Event Log Capacity:
Event Log Validity:
View Event Log:
Event Logging:
Display only
Display only
■
Enter
[Enter]
Allows you to view content of event log
Turns event logging on and off for all DMI events.
■
Disabled
Enabled
[Enabled]
■
■
System Boot Event:
Clear All Event Logs:
Mark Events as Read:
Disabled
Enabled
[Disabled]
[Yes]
Turns event logging on and off for DMI system boot events.
When set to [Yes] all event logs will be cleared at next boot.
■
■
No
Yes
■
■
Enter
[Enter]
Allows you to mark all events currently in the event log as having
been read.
14
S e c u r i t y M e n u
SECURITY MENU – SETTING THE SECURITY FEATURES
The Security menu allows you to set up the data security
features of your notebook to fit your operating needs
and to view the current security configuration. (See
Navigating Through The Setup Utility on page 2 for more
information.)
■
If you make an error when re-entering
the password a [Warning] will be dis-
played on the screen. To try again press
the Enter key and then retype the pass-
word. Press the Esc key to abort the
password setting process.
The following tables show the names of the menu fields
for the Security menu and its submenus, all of the
options for each field, the default settings and a
description of the field's function and any special
information needed to help understand the field's use.
The default condition is no passwords required and no
write protection.
■
Entering a password incorrectly 3 times
in a row will cause the keyboard and
mouse to be locked out and the warning
[System Disabled]to be displayed.
If this happens restart the computer by
turning off and on the power with the
power switch and use the correct pass-
word on reboot.
If you set a password, write it down and
keep it in a safe place. If you forget the
password you will have to contact your
support representative to regain access to
your secured functions and data.
■
If the Power Management Security is
Enabled and the Password on Boot is
Disabled you will not have to type your
password upon resuming the system
from the Suspend or Save-to-Disk
modes. Power Management Security
will work only if Password boot is
enabled.
InsydeH20 Setup Utility
Advanced Security
Information
Main
Boot
Exit
Press <Enter> key to set
Supervisor Password to
enable any password
features.
Supervisor Password
User Password
:Clear
:Clear
Set Supervisor Password
Set User Password
Set User Password Length:
Password on Boot:
On Automatic Wake up:
KB Lock on Resume:
Boot from Removable Media:
Flash Write:
<Enter>
<Enter>
<0>
<Disabled>
<Disabled>
<Disabled>
<All>
Then password entry is
required to enter BIOS
Setup.
<Enabled>
Up/Dn Select Boot Device
Hard Disk Security
Owner Information
<>
Select Screen
Select Item
Enter Select
F1 = Help
Submenu
F9 = Setup Defaults
F10 = Save and Exit
Esc = Exit
Figure 10. Security Menu
15
L i f e B o o k
N
S e r i e s N o t e b o o k B I O S
Table 10: Fields, Options and Defaults for the Security Menu
Menu Field
Options
Default
Description
Supervisor
Password is:
–—
Clear
A display-only field. Set is displayed when the system supervisor password
is set and Clear when it is not.
User Password is:
–—
–—
Clear
A display-only field. Set is displayed when the general user
password is set, and Clear when it is not.
Set Supervisor
Password
[Enter]
Sets, changes or cancels the Supervisor Password. Supervisor’s Password
may be up to seven characters long and must include only letters or num-
bers (no symbols). Passwords are NOT case- sensitive. To cancel a pass-
word press the Enter key instead of entering characters in the Enter New
Password field and in the Re-enter New Password field. When a Supervi-
sor Password is set it must be used to access the BIOS setup utility.
Set User Password
–—
[Enter]
This field can only be accessed if the Supervisor Password is set. Sets,
changes or cancels the User Password. The User Password may be up to
seven characters long and must include only letters or numbers (no
symbols). Passwords are NOT case-sensitive. To cancel a password press
the Enter key instead of entering characters in the Enter New Password
field and in the Re-enter New Password field. When a User Password is
set it must be used to access the BIOS setup utility.
Set User
Password Length:
–—
[0]
Supervisor can set password length (0 to 8) for user password.
User cannot set a password shorter than the minimum length.
■
Password on Boot:
Disabled
First Boot
Every Boot
[Disabled]
When set to First Boot, a password (User or Supervisor) is required just
once after the Power On Self Test (POST) before the operating system
will be read from a disk. When set to Every Boot, a password (User or
Supervisor) is required every time after the Power On Self Test (POST)
before the operating system will be read from a disk. When set to Dis-
abled no password is required.
■
■
■
■
On Automatic
Wake up:
Disabled
Enabled
When set to Disabled, it is not necessary to enter a password to wake up
from LAN or Real Time Clock (RTC). When Enabled, it is still necessary to
enter a password after automatic wake-up.
[Disabled]
[Disabled]
■
■
KB Lock on
Resume:
Disabled
Enabled
When set to Enabled, the PS/2 mouse and keyboard inputs are locked out
upon Resume from Suspend or Save to Disk mode until you enter the
password. When set to Disabled no password is required. If no Supervisor
Password is set, this feature is not available and no password is required.
■
■
Boot from
Removable Media:
All
[All]
When All is selected, booting from removable media is not restricted.
When Supervisor Only is selected, only the Supervisor (i.e., the user who
enters Supervisor password), can boot from removable media.
Supervisor only
■
■
Flash Write:
Disabled
Enabled
[Enabled]
When set to [Disabled], the BIOS Flash memory is write protected.
Hard Disk Security:
–—
–—
–—
–—
Configures hard disk security features
Sets Owner information.
Owner
Information:
Exiting from the Security Menu
When you have finished setting the parameters on the Security Menu, you can either exit from setup utility or move to
another menu. If you wish to exit from setup utility, press the Esc key to go to the Exit Menu. If you wish to move to
another menu, use the cursor keys.
16
S e c u r i t y M e n u
Hard Disk Security Submenu of the Security Menu
The Hard Disk Security Submenu is for configuring hard disk security features.
InsydeH20 Setup Utility
Information
Main
Advanced
Security
Boot
Exit
Press <Enter> key to set
Hard Disk Password. The
hard disk is locked
with the password. Data
in the locked disk
cannot be read on other
systems.
[Hard Disk Security]
Drive0 Password:
Set Drive0 Password
Clear
<Enter>
Password Entry on Boot
<Enabled>
Up/Dn Select Boot Device
<>
Select Screen
Select Item
Enter Select
F1 = Help
Submenu
F9 = Setup Defaults
F10 = Save and Exit
Esc = Exit
Figure 11. Hard Disk Security Submenu
Table 11: Fields, Options and Defaults for the Hard Disk Security Submenu of the Security Menu
Menu Field
Options
Default
Description
Drive0 Password Is:
Clear
The default is Clear. When the Drive0 Password has been set in the field below, the
field changes to Set.
---
Set Drive0
Password:
[Enter]
When the Drive0 Password has been set, the field can be changed. When enabled,
the hard disk is locked with the password. Data in the locked disk cannot be read on
any systems other than the original system on which it is locked or systems that
have the identical password setting.
---
■
Password Entry
on Boot:
Disabled
Enabled
[Enabled]
When disabled, the master password entry is not required before booting the oper-
ating system, but the hard disk is still password-protected without password entry.
■
17
L i f e B o o k
N
S e r i e s N o t e b o o k B I O S
Owner Information Submenu of the Security Menu
The Owner Information Submenu is for setting owner information. Note that the owner information cannot be set
without having entered a Supervisor password.
InsydeH20 Setup Utility
Information
Main
Advanced
Security
Boot
Exit
Press <Enter> key to set
owner information. Up
to 80 characters can be
set. Available
characters are ASCII
codes from 32 through
126.
[Owner Information]
Owner Information:
Clear
Set Owner Information
<Enter>
Foreground Color
Background Color
<Gray>
<Black>
The owner information
is always displayed at
the bottom line of the
screen during POST.
Up/Dn Select Boot Device
<>
Select Screen
Select Item
Enter Select
F1 = Help
Submenu
F9 = Setup Defaults
F10 = Save and Exit
Esc = Exit
Figure 12. Owner Information Submenu
Table 12: Fields, Options and Defaults for the Owner Information Submenu of the Security Menu
Menu Field
Options
–—
Default Description
Owner Information Is:
Set Owner Information:
Clear
Display only.
–—
[Enter]
Field to write owner
information, (i.e., name).
■
■
■
■
■
■
■
■
■
■
■
Foreground Color:
Background Color:
Black
Blue
Green
Cyan
Red
Magenta
Brown
White
Gray
Light Blue
Light Green
Light Cyan
Light Red
Light Magenta
Yellow
[Gray]
[Black]
Set foreground color.
■
■
■
■
Bright White
■
■
■
■
■
■
■
■
■
■
■
■
Black
Blue
Green
Cyan
Red
Magenta
Brown
White
Gray
Light Blue
Light Green
Light Cyan
Light Red
Light Magenta
Yellow
Set background color.
■
■
■
■
Bright White
■
18
B o o t M e n u
BOOT MENU – SELECTING THE OPERATING SYSTEM SOURCE
The Boot Menu is used to select the order in which the
BIOS searches sources for the operating system. (See
Navigating Through The Setup Utility on page 2 for more
information.)
The following tables show the names of the menu fields
for the Boot menu and its submenu, all of the options
for each field, the default settings and a description of
the field's function and any special information needed
to help understand the field's use.
InsydeH20 Setup Utility
Information
Quick Boot
Diagnostic Screen
Boot Menu
Main
Advanced
Security
Boot
Exit
<Enabled>
<Disabled>
<Enabled>
<Enabled>
[Disabled]
All Diagnostic Tests
will be done.
PXE Boot to LAN
[Enabled]
Boot Device Priority
Hard Disk Drive
CD/DVD-ROM Drive
Network Boot Device
Some diagnostic tests
may be skipped while
booting to speed up.
Up/Dn Select Boot Device
<>
Select Screen
Select Item
Enter Select
F1 = Help
Submenu
F9 = Setup Defaults
F10 = Save and Exit
Esc = Exit
Figure 13. Boot Menu
Table 13: Fields, Options and Defaults for the Boot Menu
Menu Field
Options
Default
Description
■
QuickBoot
Disabled
Enabled
[Enabled]
Turns on and off booting with a truncated set of Power On Self Test. (Fewer
tests mean faster turn on.)
■
■
Boot-time
Diagnostic Screen
Disabled
Enabled
[Disabled]
[Enabled]
Turns on and off display of test results instead of Fujitsu logo screen during
Power On Self Test.
■
■
Disabled
Enabled
Boot Menu
This field is not active unless the Supervisor’s Password has been set. When
disabled, access to the Boot Menu with the [F12] key is disabled. When
enabled, the Boot Menu is enabled and the [F12] key will allow you to dis-
play it..
■
■
PXE Boot to LAN
Disabled
Enabled
[Enabled]
—
Turns on and off the preboot execution environment feature.
■
Boot Device Priority
—
This menu allows setting up the source for the operating system.
See “The Boot Device Priority Submenu” in the following section.
19
L i f e B o o k
N
S e r i e s N o t e b o o k B I O S
Table 13: Fields, Options and Defaults for the Boot Menu
Menu Field
Options
Default
Description
Hard Disk Drive
—
—
This menu allows you to select which hard disk drive to use for booting up (in
cases in which there are multiple hard disk drives). See “The Boot Device Priority
Submenu” in the following section.
CD/DVD-ROM
Drive
—
—
—
—
This menu allows you to select which optical drive to use for booting up (in cases
in which there are multiple optical drives).. See “The Boot Device Priority Sub-
menu” in the following section.
Network Boot Drive
This menu allows you to select which network boot drive drive to use for boot-
ing up (in cases in which there are multiple network boot drives).See “The Boot
Device Priority Submenu” in the following section.
20
B o o t M e n u
Boot Device Priority Submenu of the Boot Menu
The Boot Device Priority Submenu is for setting the order of checking of sources for the operating system.
InsydeH20 Setup Utility
Information
Main
Advanced
Security
Boot
Exit
Boot Device Priority
Floppy Drive
Hard Disk Drive
CD/DVD-ROM Drive
Network Boot Device
Up/Dn Select Boot Device
<>
Select Screen
Select Item
Enter Select
Submenu
F1
F9
=
=
Help
Setup Defaults
F10 = Save and Exit
Esc = Exit
Figure 14. Boot Device Priority Submenu
■
■
Be aware of the operating environment when booting from a CD-ROM/DVD-ROM or you may over-
write files by mistake.
A bootable CD-ROM/DVD-ROM has either a floppy disk format or a hard drive format. When the
bootable CD-ROM/DVD-ROM is used, the drive allocations change automatically without changing the
BIOS setup. If a floppy disk format is used, the CD-ROM/DVD-ROM becomes Drive A. The CD-ROM/
DVD-ROM will only take drive C: (hard drive format) if the internal hard drive is not present or is
disabled. The bootable CD-ROM/DVD-ROM can never use a C: designation if a formatted internal hard
drive is present since the C: designator is always reserved for the internal hard drive. The boot sequence
ignores the new drive designations, however, your application software will use the new designations..
Table 14: Fields, Options and Defaults for the Boot Device Priority Submenu of the Boot Menu
Menu Field
Description
Floppy Drive
The boot selections determine the order in which the BIOS searches for the operating system during a startup
sequence. To change the order, highlight one source by using the [up] or [down] cursor keys and then press the
[+] or [-] key to change the order number. The selections that appear above may be different for your system,
depending upon configuration.
Hard Disk Drive
CD/DVD-ROM Drive
Network Boot Drive
There may be cases in which you have multiple drives of a single type. In those cases, go to the submenu related
to the drive on the main Boot menu, and select which of the devices you wish to use. For example, if you have
two hard disk drives in your system, go to Boot -> Hard Disk Drive, and select the device you wish to use for
booting.
NOTE: Be aware that if you use the CD-ROM drive as the first boot device, certain files may be overwritten,
depending upon your operating environment.
Exiting from Boot Menu
When you have finished setting the boot parameters with the Boot menu, you can either exit from the setup utility or
move to another menu. If you wish to exit from the setup utility press the Esc key to go to the Exit menu. If you wish to
move to another menu, use the cursor keys.
21
L i f e B o o k
N
S e r i e s N o t e b o o k B I O S
EXIT MENU – LEAVING THE SETUP UTILITY
The Exit Menu is used to leave the setup utility. Follow
the instructions for Navigating Through the Setup
Utility to make any changes. (See Navigating Through
The Setup Utility on page 2 for more information.)
The following table shows the names of the menu fields
for the Exit menu, the default settings and a description
of the field's function and any special information
needed to help understand the field's use.
InsydeH20 Setup Utility
Information
Main
Advanced
Security
Boot
Exit
Exit System Setup and
save your changes.
Exit Saving Changes
Exit Discarding Changes
Load Setup Defaults
Discard Changes
Save Changes
Save Change and Power Off
Up/Dn Select Boot Device
<>
Select Screen
Select Item
Enter Select
F1 = Help
Submenu
F9 = Setup Defaults
F10 = Save and Exit
Esc = Exit
Figure 15. Exit Menu
Table 15: Fields, Options and Defaults for the Exit Menu
Menu Field
Description
Exit Saving
Changes
Exit Saving Changes will store the entries on all setup utility menus to the BIOS memory and then exit the setup utility.
A confirmation message Save Configuration changes and exit now? [Yes] [No] will be displayed.
Exit Discarding
Changes
Selecting Exit Discarding Changes will exit the setup utility with out writing to the BIOS memory. When the BIOS recog-
nizes this selection it will load the operating system and begin operation.
Load Setup
Defaults
Selecting Load Setup Defaults will load the factory preset default values for all menu fields, then display the message
Load default configuration now? [Yes] [No]. When confirmed the setup utility will return to the Exit
Menu. To return to another menu follow the directions in the Navigating Through the Setup Utility Section.
Discard
Changes
Selecting Discard Changes will load the previous values in BIOS memory for all menu fields. The message Load pre-
vious now? [Yes] [No] will be displayed. When confirmed the setup utility will return to the Exit menu. To return
to another menu, follow the directions in the Navigating Through the Setup Utility Section.
Save Changes
Selecting Save Changes will cause the new settings in all menus to be written to the BIOS memory. The message Save
configuration changes now? [Yes] [No] will be displayed. When confirmed, the setup utility will return to
the Exit menu. To return to another menu, follow the directions in the Navigating Through the Setup Utility section.
Save Changes
and Power Off
Selecting Save Changes and Power Off will cause the new settings in all menus to be written to the BIOS memory, after
which the system will power itself off. The message Save configuration changes and power off now?
[Yes] [No] will be displayed. When confirmed, the setup utility save the settings and the system will power off.
22
|