BATTERY DRIVE, FTP-608 Series
3" HIGH SPEED THERMAL PRINTER
FTP-638MCL101/103, Easy Loading Method
■ OVERVIEW
The easy loading FTP-608 MCL Series is ultra compact high
speed, battery driven thermal printer, printing 3-inch wide
paper (80mm) where platens are removable. Our original
platen removal mechanism improved paper loading and
maintenance.
The FTP-608 MCL series can be used for a variety of
applications, such as portable terminals, POS, ticket issuing
terminals, label printers, banking terminals, and
measurement and medical equipment.
■ HIGHLIGHTS
• Easy loading type
Our original platen removal mechanism improved paper
loading and maintenance.
• Ultra compact
Height 15.5 mm, width 92.3mm, depth 33.0 mm for the 3
inch model.
•
High speed printing
It can print at 60 mm/s (480 dotlines/s) maximum by using
Fujitsu's unique head drive control.
• High resolution printing
8 dots/mm of resolution printing is possible.
1
FTP-638MCL101/103
■ SPECIFICATIONS
Specification
Item
FTP-638MCL101/103
Interface
Conforms to RS232C / Centronics
4.2 VDC to 8.5 V, average current 1.37A (1.53) peak value
Printing ratio: 12.5%, printing speed 50mm/sec., 7.2 V
For print head
Operating
For motor
4.2 VDC to 8.5 V, 1 A maximum
2.7 to 5.25 VDC, 0.1 A maximum
92.3 x 33.0 x 15.5 mm (WxDxH)
69.3 x 52.0 x 15.0 mm (WxDxH)
Approximately 52g
Voltage
For logic
Printer mechanism
Interface board
Printer mechanism
Interface board
Dimensions
Weight
Approximately 20g
Pulse resistance: 100 million pulses/dot (under our
standard conditions). Abrasion resistance: paper traveling
distance 50km (print ratio: 25% or less)
Head life
Operating temperature*
Operating humidity
Storage temperature
Storage humidity
0˚ C to +50˚ C
20 to 85% RH (no condensation)
-20˚ C to +60˚ C (paper not included)
5 to 95% RH (no condensation)
Operating
environment
Head temperature
detection
Detected by thermistor
Detection
function
Paper out/mark detection Detected by photo-interrupter
High sensitive paper:
TF50KS-E4 (Nippon Paper)
TK50KS-E (Nippon Paper)
PD150R (Oji Paper)
Standard paper:
FTP-030P0701 (80mm)
TK60KS-F1 (Nippon Paper)
PD170R (Oji Paper)
AFP220VBB-1 (Mitsubishi)
FTP-030P0102 (80mm)
Recommended thermal sensitive paper
Medium life storage paper:
Long life storage paper:
PD160R-N (Oji Paper)
AFP-235 (Mitsubishi Paper)
TP50KJ-R (Nippon Paper)
HA220AA (Nippon Paper)
*+5˚C to +40˚C printing density assurance rance (-25 to 70˚C capability)
3
FTP-638MCL101/103
■ FUNCTION
Item
Item
8. Motor power saving function
9. Mark detection function
1. Test print function
2. Paper out detection
3. Paper near end detection
4. Platen open detect
10. MCU operation abnormality detection
11. Power ON/OFF sequence protection
Thermal head temperature abnormality
detection
5.
12. Motor over-current protection
13. Hardware timer
6. Blow-out fuse detection
7. Head voltage abnormality detection
4
FTP-638MCL101/103
■ DIMENSIONS
1. Printer mechanism: 3 inch
FTP-638MCL101
FTP-638MCL103
center of paper
center of paper
87.8
80.0
80.
35(paper end sensor)
35(paper end sensor)
10.7
10.7
15.5
15.5
4.6
44.7
4.6
44.7
84.2
86.7
87.6±0.1
84.2
86.7
87.6±0.1
Note: 1. Dimensions are nominal value (tolerance ±5 unless otherwise specified).
Unit: mm
2. Dimension listed in ( ) is for reference
2. Interface board
Unit: mm
5
FTP-638MCL101/103
FTP-638 MCL101/103
Thermal head, control circuit side connector: 5597-21CPB Molex or equivalent product
No
1
Signal
I/O Contents
PHK
—
I
Cathode for photo interruptor
2
VSEN
PHE
Paper sensor power
3
O
Emittor for photo interruptor
4
N.C. (101)/ SW1 (103) —/O Platen release switch
N.C. (101)/ SW2 (103) —/I Platen release switch
5
6
VH
VH
DI
—
—
I
Head drive power
7
8
Data in
9
CLK
I
Synchronous clock for communication
10 GND
11 GND
12 STB5
13 STB4
14 STB3
15 VDD
16 TM
—
—
I
Ground power supply for thermal head
Thermal head energizing control signal
I
I
I
Logic power
O
I
Thermally sensitive resistor input termnial 1
17 STB2
18 STB1
19 AEO2
20 AEO1
21 GND
22 GND
23 LAT
24 DO
Thermal head energizing control signal
---
I
I
I
—
—
I
Ground power supply for thermal head
Data latch
Data out
O
I
25 VH
Power supply for thermal head
26 VH
I
27 MT/A
28 MT/A
29 MT/B
30 MT/B
I
I
Stepping motor excitation signal
I
I
6
FTP-638MCL101/103
Europe
Japan
Fujitsu Components Europe B.V.
Diamantlaan 25
2132 WV Hoofddorp
Netherlands
Fujitsu Component Limited
Gotanda-Chuo Building
3-5, Higashigotanda 2-chome, Shinagawa-ku
Tokyo 141, Japan
Fujitsu Components
International
Headquarter
Offices
Tel: (31-23) 5560910
Fax: (31-23) 5560950
Email: [email protected]
Tel: (81-3) 5449-7010
Fax: (81-3) 5449-2626
Email: [email protected]
Asia Pacific
North and South America
Fujitsu Components America, Inc.
250 E. Caribbean Drive
Sunnyvale, CA 94089 U.S.A.
Tel: (1-408) 745-4900
Fujitsu Components Asia Ltd.
102E Pasir Panjang Road
#04-01 Citilink Warehouse Complex
Singapore 118529
Tel: (65) 6375-8560
Fax: (1-408) 745-4970
Fax: (65) 6273-3021
Email: [email protected]
Email: [email protected]
© 2004 Fujitsu Components America, Inc. All company and product names are trademarks or registered
trademarks of their respective owners. Rev. 11/15/2004.
7
|