|
GE Monogram
®
Use and Care Guide
Stainless Steel
Professional
48″ Gas Cooktop
Read this guide carefully. It is intended to help If you don’t understand something or need
Before
using
your
you operate and maintain your new cooktop
properly.
more help, call:
GE Answer Center®
800.626.2000
Keep it handy for answers to your questions.
cooktop
24 hours a day, 7 days a week
You’ll find them on a label in the rear of the
burner box below the burner grates.
Before sending in this card, please write these
numbers here:
Write
down the
model &
serial
These numbers are also on the Consumer
Product Ownership Registration Card
included in this guide.
Model Number
numbers
Serial Number
Use these numbers in any correspondence or
service calls concerning your cooktop.
Immediately contact the dealer (or builder)
that sold you the cooktop.
If you
received a
damaged
cooktop
Before you request service, check the Problem
Solver in the back of this guide.
It lists causes of minor operating problems that
you can correct yourself.
Save time
& money
To obtain service, see the Consumer Services
page in the back of this guide.
NEXT, if you are still not pleased, write all the
details—including your phone number—to:
If you
need
service
We’re proud of our service and want you to be
pleased. If for some reason you are not happy
with the service you receive, here are three
steps to follow for further help.
Manager, Consumer Relations
GE Appliances
Appliance Park
Louisville, KY 40225
FIRST, contact the people who serviced your
appliance. Explain why you are not pleased. In
most cases, this will solve the problem.
FINALLY, if your problem is still not resolved,
write:
Major Appliance Consumer
Action Program
20 North Wacker Drive
Chicago, IL 60606
3
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY NOTICE
• The California Safe Drinking Water and
Toxic Enforcement Act requires the
• Gas appliances can cause minor exposure to
four of these substances, namely benzene,
carbon monoxide, formaldehyde and soot,
caused primarily by the incomplete
Governor of California to publish a list of
substances known to the state to cause birth
defects or other reproductive harm, and
requires businesses to warn customers of
potential exposure to such substances.
combustion of natural gas or LP fuels.
Properly adjusted burners, indicated by a
bluish rather than a yellow flame, will
minimize incomplete combustion. Exposure
to these substances can be minimized by
venting with an open window or using a
ventilation fan or hood.
SAFETY PRECAUTIONS
When using your appliance, follow basic safety • Be sure your cooktop is correctly adjusted
precautions, including the following:
by a qualified service technician or installer
for the type of gas (natural or LP) that is
to be used.
• Have the installer show you the location of
the cooktop gas cut-off valve and how to shut
it off if necessary.
WARNING: These adjustments must be
made by a qualified service technician in
accordance with the manufacturer’s
instructions and all codes and requirements
of the authority having jurisdiction. Failure to
follow these instructions could result in
serious injury or property damage. The
qualified agency performing this work
assumes responsibility for the conversion.
• Be sure all packing materials are removed
from the cooktop before operating it to
prevent fire or smoke damage should the
packing material ignite.
• Locate the cooktop out of kitchen traffic path
and out of drafty locations and areas with
poor air circulation.
• Do not attempt to repair or replace any part
of your cooktop unless it is specifically
recommended in this guide. All other
servicing should be referred to a qualified
technician.
• Use this appliance only for its intended use as
described in this guide.
• Be sure your appliance is properly installed
and grounded by a qualified technician in
accordance with the provided installation
instructions.
4
SAFETY PRECAUTIONS
• Before performing any service,
• When cooking, do not touch the burners,
burner grates, grille or griddle (on some
models) or the surrounding areas.
DISCONNECT THE COOKTOP POWER
SUPPLY AT THE HOUSEHOLD
DISTRIBUTION PANEL BY REMOVING
THE FUSE OR SWITCHING OFF THE
CIRCUIT BREAKER.
These surfaces may be hot enough to burn.
During and after use, do not touch, or let
clothing or other flammable materials
contact, the burners, grille or griddle (on
some models) or areas near the burners;
allow sufficient time for cooling first.
• Do not leave children alone—children should
not be left alone or unattended in an area
where an appliance is in use. They should
never be allowed to sit or stand on any part of
the appliance.
Potentially hot surfaces include the cooktop,
areas facing the cooktop and the drip tray
handles.
• Do not allow anyone to climb, stand or hang
on the drip tray handles or cooktop. They
could damage the cooktop and even tip it
over, causing severe personal injury.
The drip trays can get hot. Do not remove the
drip trays until they are cool.
• Do not store flammable materials near
the cooktop.
• Keep the ventilator hood and grease filters
clean to maintain good venting and to avoid
grease fires. Turn the ventilator OFF in case
of fire or when intentionally “flaming” liquor
or other spirits on the cooktop. The blower, if
in operation, could spread the flames.
• CAUTION: ITEMS OF INTEREST TO
CHILDREN SHOULD NOT BE STORED
IN CABINETS ABOVE A COOKTOP—
CHILDREN CLIMBING ON THE
COOKTOP TO REACH ITEMS COULD
BE SERIOUSLY INJURED.
• DO NOT obstruct the flow of combustion or
ventilation air to the appliance. Be sure a
fresh air supply is available.
• For your safety, never use your appliance for
warming or heating the room.
• Never wear loose-fitting or hanging garments
while using the appliance. Be careful when
reaching for items stored over the cooktop.
Flammable material could be ignited if
brought in contact with burners or burner
grates and may cause severe burns.
• Use only dry pot holders—moist or damp pot
holders on hot surfaces may result in burns
from steam. Do not let pot holders touch
burners or burner grates. Do not use a towel
or other bulky cloth.
5
IMPORTANT SAFETY INSTRUCTIONS
SAFETY PRECAUTIONS
• Do not use water on grease fires. Never pick up • Do not heat unopened food containers; a
a flaming pan. Turn the controls off. Smother a
flaming pan on a surface unit by covering the
pan completely with a well-fitting lid, cookie
sheet or flat tray. Use a multi-purpose dry
chemical or foam-type fire extinguisher.
build-up of pressure may cause the container
to burst.
• Set the burner control so that the flame heats
only the bottom of the pan and does not extend
beyond the bottom of the pan. Excessive flame
is hazardous. The high BTU burners can easily
melt cookware handles.
Flaming grease outside a pan can be put out by
covering it with baking soda or, if available, by
using a multi-purpose dry chemical or foam-
type fire extinguisher.
• Hold the handle of the pan, using a dry pot
holder, to prevent movement of the utensil
when stirring or turning food.
• DO NOT STORE OR USE COMBUSTIBLE
MATERIALS, GASOLINE OR OTHER
FLAMMABLE VAPORS AND LIQUIDS IN
THE VICINITY OF THIS OR ANY OTHER
APPLIANCE.
• Always heat fat slowly, and watch as it heats.
• Always use the LITE position when igniting the
burners and make sure the burners have
ignited, including the center simmer flame.
• Do not let cooking grease or other flammable
materials accumulate in or near the cooktop.
Clean drip trays and liners after every use.
• Never leave the burners unattended at high
flame settings. Boilovers cause smoking and
greasy spillovers that may catch on fire. If the
burner flames are smothered by a severe
boilover which affects the ignitor, unburned
gas will escape into the room.
• If you smell gas, the installer has not done a
proper job of checking for leaks. You can have
a small leak and therefore a faint gas smell if
the connections are not completely tight.
• Do not let pot holders come near open flames
when lifting cookware. Do not use a towel or
other bulky cloth in place of a pot holder.
Finding a gas leak is NOT a do-it-yourself
procedure. Some leaks can only be found with
the burner control in the ON position and for
your protection it must be done by a qualified
service technician. Never use an open flame to
locate a leak.
• To minimize the possibility of burns, ignition
of flammable materials and spillage, turn
cookware handles toward the side or back of
the cooktop without extending over adjacent
burners.
• If by some chance a burner goes out and gas
escapes, open a window or a door to let the
room air out. Do not attempt to use the
appliance until the gas has had time to
dissipate. Follow the instructions in What
to do if You Smell Gas.
• Never block the vents (air openings) of the
cooktop. They provide the air inlet and outlet
that are necessary for the cooktop to operate
properly with correct combustion. Air
openings are located at the drip tray and drip
tray handle area.
• Do not use aluminum foil to line any part of the
cooktop. Using a foil liner could result in a fire
hazard or the obstruction of the flow of
combustion and ventilation air. Foil is an
excellent heat insulator and heat will be
trapped underneath it. This trapped heat can
upset the cooking performance and can
damage the finish of the cooktop.
6
SAFETY PRECAUTIONS
• Always turn the burners to OFF before
• Keep all plastics away from the burners.
removing cookware.
• Do not leave plastic items on the cooktop—they
• Carefully watch foods being fried at a high
flame setting.
may melt if left too close to the vent.
• To avoid the possibility of a burn, always be
certain that the controls for all burners are at
the OFF position and all grates are cool before
attempting to remove them.
• Foods for frying should be as dry as possible.
Frost on frozen foods or moisture on fresh
foods can cause hot fat to bubble up and over
the sides of the pan.
• When flaming foods are under the hood, turn
the fan off. The fan, if operating, may spread
the flames.
• Use the least possible amount of fat for
effective shallow or deep fat frying. Filling the
pan too full of fat can cause spillovers when
food is added.
• Grease is flammable. Let hot grease cool
before attempting to handle it. Avoid letting
grease deposits collect in the container under
the cooktop burners, the grille or the griddle.
Clean these areas after each use or boilover.
• Use a deep fat thermometer whenever possible
to prevent overheating fat beyond the smoking
point.
• Never try to move a pan of hot fat, especially a
deep fat fryer. Wait until the fat is cool.
• For proper lighting and performance of the
burners, keep the burner ports clean. It may be
necessary to clean these when there is a
boilover or when the burner does not light,
even though the electronic ignitors click.
• When using glass cookware, make sure it is
designed for cooktop use.
• If a combination of oils or fats will be used in
frying, stir together before heating or as fats
melt slowly.
• Clean the cooktop with caution. Avoid steam
burns; do not use a wet sponge or cloth to clean
the cooktop while it is hot. Some cleaners
produce noxious fumes if applied to a hot
surface. Follow manufacturer’s directions.
• Do not leave any items on the cooktop. The hot
air from the vent may ignite flammable items
and will increase pressure in closed containers,
which may cause them to burst.
• Do not use the grille for cooking excessively
fatty meats or products which promote
flare-up.
• Use proper pan size—avoid pans that are
unstable or easily tipped. Select cookware
having flat bottoms large enough to properly
• DO NOT use cookware on the grille.
contain food and avoid boilovers and spillovers • If cooktop is located near a window, do not
and large enough to cover burner grate. This
will both save cleaning time and prevent
hazardous accumulations of food, since heavy
spattering or spillovers left on the cooktop can
ignite. Use pans with handles that can be easily
grasped and remain cool.
hang long curtains that could blow over the
burners and create a fire hazard.
•Be sure all the controls are turned off and the
appliance is cool before using any type of
aerosol cleaner or cooking spray on or around
the appliance. The chemical that produces the
spraying action could, in the presence of heat,
ignite or cause metal parts to corrode.
7
Features of Your Cooktop
Stainless Steel Cooktop
Design
information
3
2
4
1
(Not all features
are on all models.
Appearance may vary.)
5
6
7
ZGU48N6R
ZGU48L6R
6
8
3
9
2
4
1
5
10
7
ZGU48N4G
ZGU48L4G
6
8
9
2
4
1
5
6
10
ZGU48N6D
ZGU48L6D
6
Feature Index
Page
1
2
Burner Assemblies
9, 16
3, 24
Model and Serial Numbers
(in rear of burner box below grates—can be seen when
grates and areation pans are removed)
3
4
5
6
7
8
9
Grille
12–14, 16
17
Drain Tubes
Drip Trays
12, 17
9, 16
Burner Control Knobs
Grille Control Knob
Griddle Flue Cover (Vent)
Griddle
12, 16
14
14, 15, 17
15, 16
10 Griddle Control Knob
8
Using Your Cooktop
Stainless Steel Cooktop
The control knobs are in front of the burner,
grille or griddle (on some models) they control.
Control
knobs
HI
LITE
The burners have an infinite number of heat
settings as there are no fixed positions between
HI and LO.
To turn ON a burner, push the control in, then
turn it counterclockwise to the LITE position.
Check to be sure the burner you turned on is the
one you want to use.
You will hear the ignitor click. When the gas is
ignited all around the burner and into the central
simmer burner below the simmer cap, turn the
knob back to the desired setting.
Push the control in and turn it counterclockwise
to the LITE position.
When using the simmer burner always ensure
that it lights from the main burner.
Your new professional gas cooktop is equipped
with burners typical of those used in restaurants.
These burners are designed in three pieces for
easy cleaning and control.
Burners
Simmer cap
Simmer burner
The center, smaller cap covers and protects the
simmer burner from boilovers that could put the
flame out. This cap also spreads the simmer
burner heat out to avoid too much heat being
concentrated on the center of the pan.
The simmer burner is always on when the burner
is in use. The burner should never be operated if
the simmer cap is not in place.
Brass port ring
Outer ring
The outer cap and brass port ring constitute the
main burner and are in operation between the HI
and LO settings.
The burners have electronic spark ignition to
eliminate continuously burning pilots. When the
outer ring is on and the flame is blown out, it will
relight. The burners are rated at 15,000 BTU
around the outer ring. When turned to the
simmer setting, only the center of the burner is
lit, and it is rated at 500 BTU.
9
Using Your Cooktop
Stainless Steel Cooktop
NOTE: Keep the ignitor, ignitor cap and burner
ports clean.
Electronic
ignitors
Ignitor
If a burner does not ignite, listen for the
clicking sound. If the ignitor is not clicking,
turn off the burner. Check the circuit breaker
for a blown fuse or a tripped circuit breaker. If
the ignitor still fails to operate, check the
Problem Solver in the back of this guide or the
Power Failure information in this section.
Simmer
ignition
channels
NOTE: If you are using propane gas, a slight pop
or flash may occur at the burner ports a few
seconds after the burner has been turned off.
This “extinction pop” is normal for propane gas.
Burner base
Your new professional gas cooktop has
The flame travels through the simmer ignition
channels and crosses over onto the simmer
burner located just beneath the simmer cap.
When lighting only the simmer burner, always
Simmering
exceptionally low simmering capabilities. The
center simmer cap serves as a heat diffuser to
spread out the heat to avoid having a center hot
spot. Keep in mind that because of the high heat light the main burner first. This will in turn
capacity of the outer burner, and the mass of the provide the ignition source for the simmer
cast iron burner grates (they retain heat longer
than lighter, conventional grates), some foods
may continue to cook by retained heat after the
burner has been turned off.
burner. Ensure that the simmer ports are lit
before turning the control knob down to the
simmer position. Should a strong draft or
boilover extinguish the simmer flame it will not
relight automatically as the outer burner would.
The simmer burner is lit from the outside burner
flame.
The burner flame should burn completely
around and within the burner with no excessive
noise or lifting. The flame should be blue in
color and stable with no yellow tips.
During initial use, foreign particles in the gas
line, or dust in the air or around the appliance
may cause an orange flame. This will disappear
with use.
Burner
efficiency
and flame
characteristics
An improper air-gas mixture may cause either
a burner flutter or a yellow-tipped flame.
A technician should adjust the flame.
10
Incorrect
Correct
The correct height of the flame mainly depends
on the size of the bottom of the cooking utensil,
the material of the cooking utensil, the amount
and type of food and the amount of liquid in
the utensil.
Flame
height
For safe handling of cookware, never let the
flame extend up the sides of the cookware. Any
flame larger than the bottom of the cookware is
wasted heat and only serves to heat the handle.
Note: The flame size on a gas burner should match the
Watch the flame, not the knob, as you reduce
the heat.
cookware you are using.
• For safety reasons the flame must never extend
beyond the bottom of the cooking utensil.
Never allow flames to curl up the side of the
pan.
• Be very careful if the pans have plastic handles,
as these large professional-size burners can
flame up on the outside of the pan and melt or
bubble the handles.
3″
• Utensils which conduct heat slowly (such as
glass-ceramic) should be used with medium to
low flames. If you are cooking with a large
amount of liquid a slightly larger flame can
be used.
The electric ignition that lights the surface
burners will not operate during a power
failure.
It is necessary to light each burner separately
each time you want to use it during a power
failure.
Power
failure
To light the surface burners during a power
failure, turn the control knob for the burner
you want to light to LITE while holding a
lighted match to the outer ring. After the
flame is burning all the way around the burner,
adjust the flame.
The grille and griddle (on some models) can
not be used during a power failure.
11
Using Your Cooktop
Stainless Steel Cooktop
Do not operate a burner for an extended
period of time without cookware on the grate.
The finish on the grate may chip without
cookware to absorb the heat.
Glass: There are two types of glass cookware—
those for oven use only and those for surface
cooking (saucepans, coffee and teapots). Glass
conducts heat very slowly.
Cookware
Aluminum: Medium-weight cookware is
recommended because it heats quickly and
evenly. Most foods brown evenly in an
aluminum skillet. Use saucepans with tight-
Heatproof Glass-Ceramic: Can be used for
either surface or oven cooking. It conducts
heat very slowly and cools very slowly. Check
cookware manufacturer’s directions to be sure
fitting lids for cooking with minimum amounts it can be used on gas cooktops.
of water.
Stainless Steel: This metal alone has poor
Cast Iron: If heated slowly, most skillets will
give satisfactory results.
heating properties, and is usually combined
with copper, aluminum or other metals for
improved heat distribution. Combination
metal skillets generally work satisfactorily if
they are used at medium heat as the
manufacturer recommends.
Enamelware: Under some conditions, the
enamel of some cookware may melt. Follow
cookware manufacturer’s recommendations
for cooking methods.
Before starting to cook on the grille, be sure the
drip tray and liners are in place and that you
have the grille racks turned to the side you want
for cooking.
Using the
grille
HI
LITE
(on some models)
Preheat the grille for 15 minutes with the
control knob set on HI. When the grille is
preheated, place the food on the grille. Cook it
to the desired doneness.
NOTE: The longer you preheat the grille, the
darker the grille marks will be on your food.
During cooking it may be necessary to adjust the
heat setting. The control knob may be set to any
position between HI and LO.
For proper searing and browning the grille
requires high heat.
With large pieces of meat or poultry you may
need to turn the heat to a lower heat setting
after the food has been seared. This lower heat
setting will allow the food to cook through
without burning the outside.
Marinades and barbecue sauce should be added
toward the end of cooking time. The heat
should be turned to low when sauces are added.
Do not leave the grille unattended while it is on.
When you are finished cooking allow the grille
and the drip trays to cool before cleaning them.
They should be cleaned each time they are used.
12
Occasionally grease drippings ignite. These
drippings will create minor puffs of flame for a
second or two. This is normal when cooking on use hamburger that is lean, remove the fat
a barbecue. You may find it handy to have a
spray bottle filled with water to lightly spray the
flare-up.
To prevent flare-ups from happening, trim the
fat from around the edges of steaks and chops,
Excessive
grille flare-
ups and
from poultry, etc.
flaming
When turning any kind of meat or poultry, the
melting fat will drop onto the briquettes and it
may create a flare-up. If this happens, use a
long-handled spatula to move the food to
another area.
If the flame becomes excessive, remove the
food from the grille. Lower the heat setting.
Replace the food when the flare-up subsides.
The two-piece rack is reversible. Place the side
with the two grooved tabs toward the back of the
cooktop. The grille rack is made of cast iron and
has a black porcelain finish.
Grille rack
One side of the grille (side A) is ridged and
should be used for foods where you want the fat
to run off, such as steak or hamburger patties.
The ridges are sloped so the fat runs toward the
front of the grille and can easily run down to the
cooler area of the drip tray and away from the
intense heat of the burner.
The other side of the grille (side B) was
designed for foods that need more support
while cooking, such as fish.
Food cooked on this grille achieves the same
flavor as food cooked on an outdoor grille. The
intense radiant heat from the ceramic
briquettes caramelizes the fats and juices that
are brought to the surface of the food, giving it
the barbecued flavor.
Side A
Side B
This gas grille may cook slightly faster than you
are used to.
13
Using Your Cooktop
Stainless Steel Cooktop
• When turning the meat over, always use a
spatula as it will not puncture the meat
allowing the juices to run out. This will help to
keep the meat juicy. Turn the meat only once,
as juices are lost when the meat is repeatedly
turned. Season or salt the meat after it has
been cooked; these procedures have a
tendency to dry the meat out.
• The doneness of meat is affected by the
thickness of the cut. It is impossible to cook a
thin piece of meat to a rare doneness. A steak
should be at least 1-inch thick to have it turn
out rare and juicy. The cooking time is
affected by the temperature of the meat when
you start to cook it, the size and shape of the
cut and the kind of meat you are cooking. The
degree of doneness desired also affects the
time.
Grilling
hints
• Be sure to trim any excess fat from meat or
poultry. To prevent steaks or chops from
curling while they are being cooked, slit the
fat around the edges at about 2-inch intervals.
To test for doneness, make a small cut in the
center of the meat.
• The U. S. Department of Agriculture says,
“Rare beef is popular, but you should know
that cooking it to only 140°F. means some
food poisoning organisms may survive.”
(Source: Safe Food Book. Your Kitchen
Guide. USDA Rev. June 1985.)
Remove the center shipping
screw. Leave the two outer
leveling screws in place.
The built-in griddle is made from Type 304
stainless steel, highly polished to provide a
smooth cooking surface. It is normal for it to
darken with use as oils cook onto the surface to
provide a stick-resistant base or “seasoning.”
Since the griddle is made from stainless steel
the surface will not rust.
Before
using the
griddle
Shipping screw
(on some models)
Griddle flue cover
Outer leveling
screws
The griddle is thermostatically controlled and
cycles on and off to maintain the set temperature.
The “HEATING” light indicates that the burner
is on.
The griddle assembly is not to be removed for
cleaning and is held in place by three rear screws.
These screws keep the griddle from shifting in
transit, and are also used for positioning to avoid
breaking ignition components.
Once the unit is in position, the rear center
shipping screw can be removed. It is located
beneath the griddle flue cover. Remove the flue
cover by lifting it straight up.
The two outer screws are leveling screws. Do not
remove these two screws. They can be turned to
level the griddle or to provide a forward slope to
help grease and oils to drain away from the food
being cooked. After using the griddle a few
times you will be able to judge the slope best for
the foods you are cooking and your personal
preference.
When replacing the griddle flue cover ensure
that the cover slips to the outside of the front
and back metal flanges of the fixed griddle
assembly. This will ensure a tight fit of the
flue cover.
14
Before using the griddle for the first time it
must be seasoned.
4 Turn the control knob to a medium setting
(350°F.). Turn the heat off when the oil
begins to smoke. Allow the griddle to cool.
Seasoning
the griddle
If the griddle has not been used for a period of
time, it should be reseasoned.
5 Repeat step 3. Be sure to cover the entire
surface with the oil.
To season the griddle:
6 Repeat step 4. Allow the griddle to cool.
Wipe the entire surface of the griddle
using a heavy cloth. Apply a very thin layer of
vegetable oil. The griddle is now ready to use.
1 Clean the griddle thoroughly with hot, soapy
water to remove any protective coating.
2 Rinse with a mixture of 1 quart water and 1
cup white vinegar. Dry thoroughly.
3 Pour 1 teaspoon vegetable oil into the center
of the griddle. Do not use corn oil as it gets
sticky. Rub the oil over the entire surface of
the griddle using a heavy cloth.
Before starting to cook on the griddle, be sure
the drip tray and liners are in place. Preheat
the griddle for 15 minutes with the control
knob set to the temperature suggested on the
Griddle Cooking Chart. When the griddle is
preheated, the HEATING light will turn off.
Place the food on the griddle and cook to the
desired doneness.
NOTE: When the griddle is properly seasoned
it can be used without any additional
shortening. However, shortening can be used
for flavor. A light mist of a non-stick vegetable
spray, applied before cooking to a cool griddle,
makes delicate foods easier to turn.
Using the
griddle
15
Care and Cleaning
Stainless Steel Cooktop
Clean up spatters with a damp cloth. Remove
heavier soil with warm, soapy water.
Control
panel and
knobs
Do not use abrasives of any kind on the control
panel.
The control knobs may be removed for easier
cleaning. To remove a knob, pull it straight off
the stem. Wash the knobs in soap and water but
do not soak.
Clean the grille immediately after cooking.
Turn off the burner. To protect your hand from
steam and heat, wear a barbecue mitt. Scrub the
grille by dipping a brass bristle barbecue brush
frequently into a bowl of water.
Grille
(on some models)
The steam created softens the food particles
and assists the cleaning process. The food
particles will drop into the drip tray or into the
radiant tray holding the ceramic briquettes. Be
sure to clean the drain tube, drip tray and liner
after they have cooled.
The layer of ceramic briquettes, under the
grille racks, will last for many years with proper occur as they may get brittle with age,
care.
Chipping or cracking of the briquettes may
Ceramic
briquettes
(on some models)
depending on the frequency of use. This is
normal and does not affect the performance.
Burned-on food particles and ash can be
emptied off the radiant tray when cool by
shaking over a waste receptacle.
Do not replace the radiant tray/briquettes with
alternates.
Do not use a steel wool pad; it will scratch the
surface.
For hard to clean soil use a standard stainless
steel cleaner such as Bon-Ami,® Cameo® or Bar
Keepers Friend.® Apply cleaner with a damp
sponge, rinse thoroughly and dry. Always scrub
lightly in the direction of the grain.
Stainless
steel
Clean with hot soapy water. Rinse and dry.
If food soil remains, try a general kitchen
cleaner, such as Fantastik®, Simple Green®
or Formula 409.®
After cleaning, use a stainless steel polish such
as Stainless Steel Magic®.
16
Drain tubes
Located beneath the cooktop are two drip trays.
If you have a griddle or a grille there will also be
a tray liner. The drip trays and liners are made
of stainless steel. The drip trays are on rollers so
they are easy to remove and replace.
Drip trays,
drip tray
liners and
drain tubes
CONV
BAKE
OFF BAKE BROIL PROOF
OVEN
O
F
F
B
A
K
E
BROIL CLEAN
FRONT
REAR
FRONT
REAR
GRILL
GRIDDLE
OVEN
OVEN ON
HEATING
To remove the drip tray, pull it forward. If
something has spilled into the tray it should be
cleaned up as soon as possible to prevent
“baked on” food soil.
OVEN ON
HEATING
DOOR LOCKED
Grease from the griddle or the grille drains
through the drain tubes into the tray and into
the liner below.
Drip trays
Liner
Do not allow the grease to accumulate in the
drip tray or liner as it can be a fire hazard. Clean
the drip tray and liner as soon as they are cool.
Clean with hot soapy water.
To clean the drain tube use a soapy bottle
brush. A mild abrasive cleaner such as Bon-
Ami® or Soft Scrub® can be used. For stubborn
stains, use a soap-filled steel wool pad or a harsh
abrasive cleaner such as Comet® or Ajax®,
rubbing lightly. Rinse all parts thoroughly.
Thoroughly clean the griddle of grease and
food particles, using a square-edged spatula,
while it is still hot.
Griddle
(on some models)
Wipe the griddle with a dry heavy coarse cloth
to remove any remaining residue and food
particles.
Wash with hot soapy water, rinse and dry.
Once the griddle has cooled rub the surface
lightly with vegetable oil. Do not use corn oil as
it gets sticky.
If the griddle is cleaned with anything other
than a dry heavy coarse cloth, it will need to be
reseasoned.
Never flood the hot griddle with cold water.
This could cause the griddle to crack or warp.
17
Care and Cleaning
Stainless Steel Cooktop
Ignitor
Burner
cap
The burner assemblies should be washed
regularly and, of course, after spillovers.
Burner
assembly
Turn all the controls to OFF before removing
the burner parts.
The electrode of the spark ignitor is exposed
beyond the top of the burner. When cleaning
the burner trays, be careful not to snag the
electrode of the spark ignitor with your cleaning
cloth. Do not hit the spark ignitor. Be careful not
to turn on any surface controls while cleaning
the burner trays. A slight electrical shock might
result which could cause you to knock over hot
cookware.
Burner
ports
CAUTION:
The burner grates, burner tops and trim rings
can be lifted off, making them easy to clean.
Removing them gives you access to the burner
bodies and burner trays.
Do not operate the burner without all burner parts in place.
To avoid snagging cloth on spark ignitors, leave
burner caps in place when cleaning burner
trays.
The burners have been designed in three pieces
for ease of cleaning. When the burner grate and
the burner are cool, remove the grate. The
center ring, the burner cap and the port ring
can easily be lifted off. Wash these parts in hot
soapy water, rinse and dry thoroughly.
The burner grates, center ring and the burner
cap are porcelain enamel. When cool they may
be wiped clean using hot soapy water, then
rinsed and wiped dry. When lifting the burner
grates be careful as they are heavy. Place them
on a protected surface, so they won’t scratch the
surface of the cooktop.
The port ring is brass; a bristle brush can be
used to clean out the toothed burner ports, if
necessary.
After cleaning, it is important to make sure the
locating pin on the bottom side of the brass port
ring is properly aligned with the corresponding
hole in the burner base. Incorrect alignment
will produce a potentially dangerous flame and
poor burner performance.
18
The Problem Solver
Stainless Steel Cooktop
PROBLEM
POSSIBLE CAUSE
Questions?
Use this
problem
solver!
BURNERS DO
NOT LIGHT
•Burners assembled incorrectly after cleaning. Make sure the burner
assembly is put together correctly and that the port ring is aligned.
•Clean the ignitor orifice.
•Inspect the manual cut-off valve to insure that it is not closed.
•Make sure the electrical plug is plugged into a live power outlet.
•Check for a power outage.
BURNER FLAMES
VERY LARGE
OR YELLOW
•Improper LP gas connection. See the Installation Instructions.
TICKING SOUND
OF SPARK IGNITOR
AFTER BURNER
LIGHTS
•The spark ignitor is not deactivated. Turn the burner OFF and
relight. Some ticking is normal. If ticking is excessive call for service.
STRONG ODOR
•Improper air/gas ratio in burners. Adjust the air shutters.
If you need more help…call, toll free:
GE Answer Center®
800.626.2000
consumer information service
19
Notes
Stainless Steel Cooktop
20
Consumer Services
With the purchase of your new Monogram appliance, receive the
assurance that if you ever need information or assistance from GE,
we’ll be there. All you have to do is call—toll- free!
Whatever your question about any Monogram major appliance, GE Answer Center®
information service is available to help. Your call—and your question—will be answered
promptly and courteously. And you can call any time. GE Answer Center® service is open
24 hours a day, 7 days a week.
GE Answer
Center®
800.626.2000
A GE consumer service professional will provide expert repair service, scheduled at a time
that’s convenient for you. Many GE Consumer Service company-operated locations offer
you service today or tomorrow, or at your convenience (7:00 a.m. to 7:00 p.m. weekdays,
9:00 a.m. to 2:00 p.m. Saturdays). Our factory-trained technicians know your appliance
inside and out—so most repairs can be handled in just one visit.
In-Home Repair
Service
800-444-1845
GE offers, free of charge, a brochure to assist in planning a barrier-
free kitchen for persons with limited mobility.
For Customers
With Special
Needs…
2’ 6"
TBXTOLITE
ON WALL
SINGLE CONTROL
FAUCET
6’ 10"
Consumers with impaired hearing or speech who have access to a
TDD or a conventional teletypewriter may call 800-TDD-GEAC
(800-833-4322) to request information or service.
8"
5"
6"
5"
7"
1’ 0"
1/8
3’
"
FLUORESCENT
FIXTURE
THIS LIGHT CAN
BE INSTALLED
IN BOTTOM OF
WALL CABINETS
800.626.2000
2’ 10"
SECTION A-A
R SHALLOW DEPTH SINKS (6") WITH REAR DRAIN.
SINK SHOULD ALSO BE UNDERCOATED
SCALE 1’ 1"
=
You can have the secure feeling that GE Consumer Service will still be there after your
warranty expires. Purchase a GE contract while your warranty is still in effect and you’ll
receive a substantial discount. With a multiple-year contract, you’re assured of future
service at today’s prices.
Service Contracts
800-626-2224
Individuals qualified to service their own appliances can have parts or accessories sent directly
to their home. The GE parts system provides access to over 47,000 parts…and all GE Genuine
Renewal Parts are fully warranted. VISA, MasterCard and Discover cards are accepted.
Parts and
Accessories
User maintenance instructions contained in this guide cover procedures intended to be
performed by any user. Other servicing generally should be referred to qualified service
personnel. Caution must be exercised, since improper servicing may cause unsafe operation.
800-626-2002
21
WARRANTY
YOUR MONOGRAM COOKTOP WARRANTY
Staple sales slip or cancelled check here. Proof of original
purchase date is needed to obtain service under warranty.
FULL ONE-YEAR WARRANTY
WHAT IS
COVERED
For one year from date of original purchase, we will provide, free of charge, parts and
service labor in your home to repair or replace any part of the cooktop that fails because
of a manufacturing defect.
This warranty is extended to the original purchaser and any succeeding owner for products
purchased for ordinary home use in the 48 mainland states, Hawaii and Washington, D.C.
In Alaska the warranty is the same except that it is LIMITED because you must pay to ship
the product to the service shop or for the service technician’s travel costs to your home.
All warranty service will be provided by our Factory Service Centers or by our authorized
Customer Care® servicers during normal working hours.
Should your appliance need service, during warranty period or beyond, call 800-444-1845.
• Service trips to your home to teach you how • Failure of the product if it is used for other
WHAT IS NOT
COVERED
to use the product.
than its intended purpose or used
commercially.
Read your Use and Care material.
• Improper installation.
If you then have any questions about
operating the product, please contact your
dealer or our Consumer Affairs office at
the address below, or call, toll free:
If you have an installation problem, contact
your dealer or installer. You are responsible
for providing adequate electrical, gas,
exhausting and other connecting facilities
as described in the Installation Instructions
provided with the product.
GE Answer Center®
800.626.2000
consumer information service
WARRANTOR IS NOT RESPONSIBLE
FOR CONSEQUENTIAL DAMAGES.
• Replacement of house fuses or resetting of
circuit breakers.
• Damage to the product caused by accident,
fire, floods or acts of God.
Some states do not allow the exclusion or limitation of incidental or consequential damages,
so the above limitation or exclusion may not apply to you. This warranty gives you specific
legal rights, and you may also have other rights which vary from state to state.
To know what your legal rights are in your state, consult your local or state consumer affairs
office or your state’s Attorney General.
Warrantor: General Electric Company. If further help is needed concerning this warranty,
write: Manager—Consumer Affairs, GE Appliances, Louisville, KY 40225
ZGU48N4G
ZGU48L4G
ZGU48N6R
ZGU48L6R
ZGU48N6D
ZGU48L6D
22
o d a y M a i l T
I m p o r t a n t
e g i s t r a t i o n O w n e r s h i p R
C o n s u m e r P r
G E A p p l i a n c e s
Place
1st Class
Letter
Stamp
Here
General Electric Company
Warranty Registration Department
P.O. Box 34070
Louisville, KY 40232-4070
23
Consumer Product Ownership Registration
Dear Customer:
Thank you for purchasing our product and thank you for placing your confidence in us. We are proud to
have you as a customer!
Follow these three steps to protect your new appliance investment:
Read your “Use and Care
Guide” carefully. It will
help you operate your new
appliance properly. If you
have questions, or need
more information call
Complete and mail
your Consumer
After completing this
registration, write your
model and serial numbers
on page 2 of this guide.
You will need this
Product Ownership
Registration today.
Have the peace of mind
of knowing we can
contact you in the
unlikely event of a
information should
you require service.
Our service number is
800-444-1845.
the GE Answer Center
®
800.626.2000.
3
1
safety modification.
2
Important: To ensure that your product is registered, fold and mail this form. No envelope is needed.
Consumer Product Ownership Registration
Product
Model
Serial
Mr. l Ms. l Mrs. l Miss l
First
Name
Last
Name
Street
Address
Apt. #
Zip
Code
City
State
Date Placed
In Use
Month
Phone
Number
Day
Year
GE Appliances
General Electric Company
Louisville, Kentucky 40225
CUT HERE
10653
Part No. 164D3333P027
Pub No. 49-8773
9-96 CG
Monogram®
General Electric Company
Louisville, KY 40225
Printed in the United States
|