™
Monogram.
ZIR36ND–GE Monogram 36" Built-In All-Refrigerator
Product Dimensions (in inches)
Design Information
10-3/4" Max.
10" Min.
24-3/4"
35" Case
Designed to be installed flush or semi-flush with surrounding cabinetry. Cutout
dimensions, clearances and side panel sizes are determined by the many
installation options available. Side panels must be used whenever the sides of
the refrigerator will be exposed. Side panels are not required when installed
into an enclosure or between pantry and oven cabinets. IMPORTANT - Side
panels, 1/2" minimum thickness are required when using FRAMELESS
CABINETS.
36" Overall
• Field installed custom panels, Lexan® or stainless steel panels are required.
The door and grille panel sizes vary to accommodate the kit being used.
• The supplied toekick is vented and must remain unobstructed for proper
air circulation.
26-3/4"
84-1/2" Max.
83-1/2" Min.
73-1/2"
Optional Panel Kits:
• ZWBR36: Black Lexan® Panel Kit
• ZWWR36: White Lexan® Panel Kit
• ZWSR36: Stainless Steel Panel Kit
Optional Custom Trim Kits:
• ZKHR1: For installation of a custom handle of your choice onto a 1/4" Panel.
• ZKTR36LH or ZKTR36RH: For installation of a 3/4" thick custom panel.
• ZKHTR1: For installation of a custom handle of your choice onto a 3/4" thick
panel. (This kit must be used in combination with ZKTR36LH or ZKTR36RH).
• ZKHRSS1: Tubular Stainless Steel handle for 1/4" thick panel.
• ZKHTRSS1: Tubular Stainless Steel handle for 3/4" thick panel.
• ZGC2: 1/4" grille panel frame side pieces for 83-1/2" and 84-1/2" installation
heights. (Factory set for 84").
4"
*Finished Width
• ZWT1: White toekick (supplied toekick is black).
Electrical
Area
Wall View
• ZFC1: Trim strip for side-by-side installation of
two products.
7 1/2"
7"
Additional Specifications
• A 115 volt 60Hz., 15 or 20 amp power supply is required. An individual
properly grounded branch circuit or circuit breaker is recommended. Install a
properly grounded 3-prong electrical receptacle recessed into the back wall.
Electrical must be located on rear wall as shown.
• Water line can enter opening through the floor or back wall. The water line
should be 1/4" O.D. copper tubing between the cold water line and water
connection location, long enough to extend to the front of the refrigerator.
Installation of an easily accessible shut off valve is recommended.
5"
24 3/4" Total
Depth
84 1/2" max
83 1/2" min
Finished
74" From Floor
to Bottom
of Electrical
Opening
5"
5" Water Supply
3 1/2"
3 1/2"
Clearances:
• If the refrigerator or freezer is installed in a corner:
A 4" clearance is required on the hinge side for a 90° door opening and
access to fresh food drawers. A 10" clearance is required on the hinge side to
remove pans.
* 36" Min. for a flush installation into an enclosure.
* 35-1/2" Min. for a semi-flush installation into an enclosure.
Note: Additional cutout width may be required when side panels
are used. Add side panel thickness to the finished cutout width to
calculate rough-in width.
®
For answers to your Monogram,
GE Profile Performance Series,™
GE Profile™ or GE appliance questions, call
GE Answer Center® service, 800.626.2000.
Listed by
Underwriters
Laboratories
R
Specification Created 8/00
™
Monogram.
ZIR36ND–GE Monogram 36" Built-In All-Refrigerator
Side By Side Installation of Freezer and Refrigerator
*Finished Width
Electrical
7"
Wall View
7 1/2"
23 1/2"
84"
7"
5"
5"
24 3/4" Total
Depth
84 1/2" max
83 1/2" min
Finished
74" From Floor
to Bottom
of Electrical
Opening
36"
5"
Water Supply
24-3/4"
36"
26"
Freezer
For a complete food storage center, install a Monogram
Freezer and Refrigerator side by side. For even more
capacity, install two refrigerators and one or two
freezers. Order ZFC1 Trim Kit to cover the side trim
and/or gap between the two products.
3 1/2"
Refrigerator
*72" min. for a flush installation
71-1/2" min. for a semi-flush installation
Note: Additional cutout width may be required when side
panels are used. Add side panel thickness to the finished
cutout to calculate rough-in width.
• The electrical and water locations must be located as
shown for either type of installation. A separate 115V,
60Hz. 20 amp power supply is recommended for each
product.
Installation Between Base and Wall Cabinet
1/4" Thick
Side Panels
Refrigerator
Cabinet
Finished Dim.
Rough-In Dim.
35-1/2"
36"
Refrigerator door
Cabinet
Refrigerator or Freezer
Note: 1/4" thick side panels
can be inserted into the case
trim, making the rough-in the
1/4" Thick
Side Panels
same as the outside trim
width, 36”.
Finished Dim.
Rough-In Dim.
71-1/2"
72"
®
For answers to your Monogram,
GE Profile Performance Series,™
GE Profile™ or GE appliance questions, call
GE Answer Center® service, 800.626.2000.
Refrigerator and Freezer
installed side-by-side
ZFC1 Trim Kit is recommended to cover side trim
and/or gap between the two products.
Listed by
Underwriters
Laboratories
R
Specification Created 8/00
™
Monogram.
ZIR36ND–GE Monogram 36" Built-In All-Refrigerator
Installation at End of Run
Refrigerator
Cabinet
Refrigerator door
Cabinet
Note: 1/2" thick side panels shown. Side
panels can be any thickness. Add side panel
thickness to outside trim width, (36” or 72" for
two models) to calculate the rough-in
dimension. The leading (front) edge must be
finished to match surrounding cabinetry.
Refrigerator and Freezer
Refrigerator or Freezer
installed side-by-side
1/2" Thick
1/2" Thick
Side Panels
Side Panels
Finished Dim.
72"
36"
37"
Finished Dim.
Rough-In Dim.
73"
Roughed-In Dim.
Frameless Cabinets
Side panels, 1/2" minimum thickness are required when using frameless cabinets. The side
panel acts as a spacer between the cabinet and the case trim and prevents interference
with cabinet door swing. The leading (front) edge must be finished to match surrounding
cabinetry.
Refrigerator
Cabinet
1/2" To 3/4" Side Panels. Leading
Edge Flush With Cabinet
Refrigerator door
Accessory Panel Kits
A wide range of custom appearance options can be created with
optional trim kits.
These refrigerators and freezers require field installed door and
grille panels.The factory installed trim will accept accessory panel
kits. White or black Lexan® and stainless steel kits are available.
Panels are cut to size and ready to install. These panel kits must be
ordered separately.
ZWBR36, Black Lexan® Panels
ZWWR36, White Lexan® Panels
ZWSR36, Stainless Steel Panels
Accessory Panel Kits Advanced Planning Exterior Appearance Options
These refrigerators and freezers are designed to be customized
with decorator door and grille panels. Field installed custom door
and grille panels are required for these models.
You should:
1. Select the appearance option.
2. Order the trim kit for that option.
3. Order the custom door and grille panels from the cabinet
manufacturer. The exact dimension for each trim kit application is
provided in this booklet. Find and pull out the page for your
application and fax or send it to the cabinet manufacturer. The
cabinet manufacturer must have this information to construct the
panels accurately.
Factory installed trim will accommodate 1/4" thick custom panels,
Lexan® or stainless steel panel kits.
Door and grille panel sizes vary to accommodate the kit being used.
Sizes are provided in this booklet.
4. Determine the final installation situation and order matching
side panels.
Caution: Maximum door panel weight is 50 pounds.
®
For answers to your Monogram,
Side panels must be used whenever the sides of the refrigerator will
be exposed. Side panel sizes vary depending on the installation.
GE Profile Performance Series,™
GE Profile™ or GE appliance questions, call
GE Answer Center® service, 800.626.2000.
3/4" thick custom panels-Without trim kits
A raised panel design, screwed or glued to a 1/4" thick backing can
be used.
Listed by
Underwriters
Laboratories
Specification Created 8/00
R
™
Monogram.
ZIR36ND–GE Monogram 36" Built-In All-Refrigerator
Custom Door Panel Dimensions Using Standard Trim
1/4" thick panels or
ZIR36N Refrigerator
ZIF36N Freezer
Panels secured to 1/4" thick backing
• 1/4" Panel: Cut panels to size.
• Custom handle with 1/4" door panel requires Trim kits ZKHR1 or ZKHRSS1
for tubular stainless steel handles.
35-1/16"
Standard Trim with Panels secured to 1/4" thick backing
• Applying a raised panel design to a 1/4" thick backing (screws or glued):
Cut 1/4" thick panels to size. Fabricate the raised panel to permit at least
2" fingertip clearance of the standard handle. 1-1/4" clearance from the
hinge side to avoid striking adjacent cabinetry and 5/16" from the top and
bottom edges to allow for the trim flange.
1/4" Thick
Custom Panel
Note: ZKHTR1 custom handle kit cannot be used in this configuration.
Custom Grille Panel
35 1/8"
68-7/8"
8"
1/4" Thick Panel
The grille panel frame is factory assembled for 84"
installation height. If installation height varies, order
ZGC2 trim kit that provides optional side trim pieces. Cut
grille panel to sizes shown below.
Important: Maximum panel is 50 pounds
Installation Height Panel Height
83-1/2"
84-1/2"
7-1/2"
8-1/2"
Raised Panel on 1/4" Thick Backing
Using Standard Handles
5/16" Clearance
1/4"
Thick
Backing
Appearance
Panel
2" Clearance
handle Side
Raised Panel
on 1/4" Thick
Backing With
Standard
1-1/4"
Clearance
hinge side
Handles
®
For answers to your Monogram,
GE Profile Performance Series,™
GE Profile™ or GE appliance questions, call
GE Answer Center® service, 800.626.2000.
5/16" Clearance
5/16" Clearance
Listed by
Underwriters
Laboratories
R
Specification Created 8/00
™
Monogram.
ZIR36ND–GE Monogram 36" Built-In All-Refrigerator
Custom Door Panel Dimensions
Using Trim Kits ZKTR36LH or ZKTR36RH
3/4" thick panel with kit supplied handle
ZIR36N Refrigerator
ZIF36N Freezer
• The ZKTR36LH (or ZKTR36RH) trim kit provides for the installation of 3/4" thick
custom door and grille panels, using the supplied handle. Cut panel to size
and install.
35 -1/16"
Important: Maximum panel is 50 pounds
3/4" Thick
Custom Panel
68-15/16"
Custom Grille Panel
35 1/4"
A
3/4" Thick Panel
Grille Panel height can vary to fill installation height.
Installation Height Dimension A
83-1/2"
84"
84-1/2”
7-1/2"
8-1/2"
8-3/4”
Important: Maintain 1-1/2” min. gap between top
of door and bottom of grille panel.
®
For answers to your Monogram,
GE Profile Performance Series,™
GE Profile™ or GE appliance questions, call
GE Answer Center® service, 800.626.2000.
Listed by
Underwriters
Laboratories
R
Specification Created 8/00
™
Monogram.
ZIR36ND–GE Monogram 36" Built-In All-Refrigerator
Custom Door Panel Dimensions Using Standard Trim
Using Trim Kit ZKTR36LH or ZKTR36RH
3/4" thick panel with custom handle
ZIR36N Refrigerator
ZIF36N Freezer
• The ZKTR36LH (or ZKTR36RH) trim kit installed together with a ZKHTR1 custom
handle kit provides for the installation of 3/4" thick custom door and grille
panels with a custom handle of your choice. Order ZKHTRSS1 for a tubular
stainless steel handle. Cut panels to size, rout the handle side of the panel as
shown below and install.
35 1/4 "
3/4" Thick
Custom Panel
With Custom
Handle
Important: Maximum panel is 50 pounds
68-15/16
Custom Grille Panel
35 1/4"
A
3/4" Thick Panel
Grille Panel height can vary to fill installation height.
Rout back side of panel as shown
on the handle side
1-13/16"
1/4"
max
Appearance Side
Installation Height Dimension A
83-1/2"
84"
84-1/2”
7-1/2"
8-1/2"
8-3/4”
Important: Maintain 1-1/2" min. gap between top of door
and bottom of grille panel.
®
For answers to your Monogram,
GE Profile Performance Series,™
GE Profile™ or GE appliance questions, call
GE Answer Center® service, 800.626.2000.
Specification Created 8/00
Listed by
Underwriters
Laboratories
R
™
Monogram.
ZIR36ND–GE Monogram 36" Built-In All-Refrigerator
Side Panel or Filler Options (Not to scale)
Side panels must be used whenever the sides of
the refrigerator or freezer will be exposed.
1/2" to 3/4" Side
Panels Leading Edge
Flush with Cabinet
23 9/16"
24 3/4"
Front. The front or
leading edge must be
finished to match
cabinetry.
1/4" Side Panels
Insert end of
side panel into trim.
Top View
Top View
84"
84"
Trim
2 9/16"
3 3/4"
Standard 4" high toekick or trim to fit.
Height may vary depending on application.
Standard 4" high toekick or trim to fit.
Height may vary depending on application.
23 5/16"
1/2" to 3/4" Side
Panels Recessed
front edge.
Top View
84"
®
For answers to your Monogram,
2 5/16"
GE Profile Performance Series,™
GE Profile™ or GE appliance questions, call
GE Answer Center® service, 800.626.2000.
Standard 4" high toekick or trim to fit.
Height may vary depending on application.
Listed by
Underwriters
Laboratories
R
Specification Created 8/00
™
Monogram.
ZIR36ND–GE Monogram 36" Built-In All-Refrigerator
Features and Benefits
• 21.9 Cu. Ft. Fresh Food Capacity
• Spill Proof Glass Shelves (6 Adjustable,
1 Full-Width Fixed)
•Sealed Snack Pans with
Full-Extension Slides
• 2 Extra Large Adjustable Humidity Produce
Pans with Easy Access Lid and Full
Extension Slides
• Wine Caddy
• 4 Large Wire Baskets with
Full-Extension Slides
• 4 Door Bins with Gallon Storage
• 2 Sealed Dairy Compartments with Glass
Covered Butter Dish
• Egg Bin
• Auto Cycle Defrost Sealed System Design
• Full Extension Accuride Slides
• Custom Panels Required
• Model ZIR36NDRH - Right hand
door opening
• Model ZIR36NDLH - Left hand
door opening
Available Fall 2000
Specification Created 8/00
|