INSTALLATION INSTRUCTIONS
Product
7160-0486, 7160-0487
Revision
Form
INST-596
Rev .B
Printing Spec: PS-001
FZ-G1 DOCKING STATION
This instruction sheet is for the FZ-G1 docking station only. For instructions on
features, set-up, and operation of the FZ-G1 computer, please refer to the
manual provided by Panasonic with the computer.
This docking station is designed to be used with a variety of Gamber-Johnson
mounting systems. Installation instructions for other Gamber-Johnson products
are provided with each individual product.
This instruction sheet is for the following products:
Item No. 7160-0486-00(-P)(-E) Keyed alike, No RF
Item No. 7160-0486-02(-P)(-E) Keyed alike, Dual RF
Item No. 7160-0486-03(-P)(-E) Keyed different, No RF
Item No. 7160-0486-04(-P)(-E) Keyed different, Dual RF
Item No. 7160-0487-00(-P)(-E) Keyed alike, No RF
Item No. 7160-0487-02(-P)(-E) Keyed alike, Dual RF
Item No. 7160-0487-03(-P)(-E) Keyed different, No RF
Item No. 7160-0487-04(-P)(-E) Keyed different, Dual RF
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
© Copyright 2012 Gamber-Johnson, LLC
If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868
FZ-G1 DOCKING STATION FEATURE IDENTIFICATON
Button Latch
Top Hooks
Slide Plate
(Keyed alike,
or Keyed different)
Base
Guide Block
(Can be removed for
use with FZ-G1 that has
an extended battery or
card slot attachment)
Alignment Tabs
Dual RF Output
Docking Connector
Dual RF Connector
Ground Pins
Cable Tie Openings
Serial
Video
RF Switch - move to
outside position for
External RF Antenna
4X Mounting Studs
(1/4-20unc for model 7160-0486)
(M6-1.0 for model 7160-0487)
15.6 Vdc Input
Ethernet
(2) USB
HDMI - If using HDMI cable, snap
ferrite (GJ# 15064 - Fair-Rite Part #
0431167281) supplied in the hardware
bag onto the HDMI cable as close to
the dock as possible
DOCKING AND UNDOCKING THE COMPUTER
Figure 1
1. Turn the computer off.
Vertical Walls
Guide Block
2. With the slide plate in the open
position, insert the bottom of the
computer into the docking station.
Make sure the guide tabs are lined up
with the pockets on the back side of
the computer.
Guide tabs
Rotate the top of the comptuter under
the top hooks until the computer is
resting on the two vertical walls sticking
out from the slide plate.
Figure 2
(see Figues 1, 2 & 3)
(Note: If your FZ-G1 computer has an
extended battery or card slot
attachment on the back side, you will
need to remove the guide block from
the face of the dock before inserting
the computer.)
3. Push downward on the slide plate
to latch the dock. (See Figure 4)
4. (Optional) The key lock can now
be used for security purposes.
Figure 3
TO UNDOCK THE COMPUTER
1. Turn the computer off.
2. Unlock if locked.
Figure 4
3. Press the Latch Button. The slide
plate is spring loaded and should raise
with your hand when you release the
button.
4. Rotate the top of the computer out
of the dock to remove.
Regulatory Certification Information
Regulatory Model #: 7160-0486
GJ Model #'s: 7160-0486-00, 7160-0486-02, 7160-0486-03, 7160-0486-04
7160-0486-00-P, 7160-0486-02-P, 7160-0486-03-P, 7160-0486-04-P
7160-0487-00, 7160-0487-02, 7160-0487-03, 7160-0487-04
7160-0487-00-E, 7160-0487-02-E, 7160-0487-03-E, 7160-0487-04-E
Descriptions: Dock-Panasonic-FZG1
Certifications:
•
•
•
•
•
•
•
•
EN 55022:2010 CISPR 22:2008 Class B
EN 50498:2010
EN 50581:2012
IEC 60950-1:/A1:2009
EN 60950-1/A12:2011
CAN/CSA C22.2 No. 60950-1/A1:2011
UL 60950-1/R:2011-12
E-Mark
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions. (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interfernece that may cause undesired operation.
10R-04 7045
Gamber-Johnson LLC, 3001 Borham Ave.,
Stevens Point, WI, 54481, USA, 715-344-3482
|