OWNERS MANUAL
FEATURES:
▪Lightweight 29 lb Design
▪Stereo 60 Watt Power
▪24-bit Stereo Studio Quality Digital Effects
▪XLR & ¼” Inputs
▪Two Channels w/ 3 Band EQ w/ Sweepable Mids ▪Dual 6.5” Woofers & Bullet Tweeters
▪Compact Monitor Shape Cabinet Design
▪Phantom Power for Condenser Mics
▪XLR Direct Outputs (left & right)
▪Speaker Stand Adaptor
PRODUCT DESCRIPTION -The lightweight Shenandoah™ Stereo 60LT is configured as a 2 channel stereo 60
watt acoustic instrument amplifier featuring stereo digital effects. Each channel is equipped with a ¼” unbalanced line
input and channel 1 is also equipped with an XLR balanced microphone input (with phantom power). The 2 inputs on
channel 1 are summed (mixed) together at a 1:1 ratio. Each channel offers a 3 band equalizer with a sweepable
midrange frequency control. Equalization centers were carefully selected for use with acoustic instruments.
Each channel also contains individual send controls to the stereo digital effects circuit. The channel signals are then
summed together, mixed with the digital effects return and passed on to the internal dual 30 watt power amplifier (60
watts total). The back panel contains stereo XLR balanced outputs with ground lift switch, stereo unbalanced line
outputs, two 1/4” speaker jacks, a headphone output, and an effects cancel jack.
ACTIVE EQUALIZATION - The Shenandoah™ Stereo 60LT contains a 3 band (with sweepable mid)
active equalizer on both channels 1 and 2. These EQ networks, similar to those found on professional sound
consoles, are very useful tools when used correctly.
LOW FREQUENCY EQ - The corner frequency of the low frequency section is 125 Hz, shelving curve. This frequency
is particularly handy when dealing with low frequency feedback from a big dreadnaught guitar. A combination of
volume reduction and turning down the low frequency control will generally get good results. Become familiar with the
action of the controls since their effective gain range is quite large. The low frequency control is also handy for adding
some “bottom” to a baritone sax and “chunk” to a mandolin or mando-cello.
HIGH FREQUENCY EQ - The corner frequency of the high frequency section is 8 kHz, shelving curve. This frequency
is especially useful for taming the bright harshness of some mandolins, violins, brass, and reeds. It can also be used
to help acoustic guitars, cellos, and flutes cut through other players in loud club situations.
MID FREQUENCY EQ - The “sweepable mid” section features 15 dB of cut or boost with a bandwidth approximately 1
octave wide. The center frequency of this filter is continuously user adjustable from 250 Hz to 5 kHz with a single
control. This filter is typically (but not always) used to reduce or remove offending frequencies in the instrument’s pick-
up response. Removing only the minimum amount necessary will yield the most acoustically rewarding results. The
easiest and most repeatable way to determine the offending frequency range is to boost the mid level somewhat (but
not to the point of feedback) and while playing, sweep the frequency control slowly across its range. You may need a
third hand until it becomes second nature, but soon you will find out just how quick it can be. You will hear a clear and
obvious accentuation of the ugliness you want to remove. The ear is a most sensitive and discriminating piece of test
equipment when used in this manner, another good reason to protect them! This is the way many touring sound
engineers equalize, since it is quick, accurate and repeatable. Occasionally, you will find need to use the mid section
in “boost” mode, particularly common when adding higher mids (bite) to an otherwise dull instrument, or adding low
mid “body” to an otherwise thin sound. Spend some time experimenting so that the process becomes creative as well
as corrective. The 9 o’clock position is 300 Hz, the 12 o’clock position is 1.25 K Hz and the 3 o’clock position is 3 K Hz.
MASTER VOLUME - The master volume control adjusts the overall volume of channel 1, channel 2 and the effects
return. Typically, best results are obtained when this control is operated between the 9 o’clock and 3 o’clock positions.
REAR PANEL
DIRECT OUTPUTS -The Shenandoah™ Stereo 60LT is equipped with left and right XLR balanced direct outputs
and unbalanced ¼” line level outputs. The left direct output also serves as a mono send. Both the XLR balanced
and ¼” unbalanced outputs make “real world sense” when connecting with other equipment. The ¼” unbalanced
outputs are true professional line level (+4 dBv) with an output impedance of 1k ohm and can drive virtually
any line level input, including power amplifiers. The XLR balanced output is “hot” mic level, rated at -30 dBv. This
configuration allows the Shenandoah™ Stereo 60LT to drive very long cable lengths (250+ feet) without problems or
added noise. The XLR balanced direct outputs can be “ground lifted” with the switch provided. This switch lifts pin 1
on the XLR balanced output to break any ground loops between the Shenandoah™ Stereo 60LT and a PA system.
Both outputs are post master volume/post EQ/post effects to aid in sending a “finished” mixed signal to a PA system
or external power amplifier.
HEADPHONE JACK -This jack, located on the rear panel, allows the user to enjoy the tone of this amp through
standard headphones (8-600 ohms). A speaker switch shuts off the internal speakers.
EFFECTS CANCEL JACK - A ¼” effects cancel jack is provided on the back panel to mute the internal effects via
footswitch. Any standard single button latching footswitch (with shielded cable) may be used. Signal is muted when
the switch is closed.
POWER AMPLIFIER -The Shenandoah™ Stereo 60LT contains an advanced stereo monolithic power amplifier
circuit that is completely protected against overloads, short circuits and thermal faults. Output is rated at 30 watts per
side (60 watts total) into 4 ohms, with excellent overload recovery characteristics.
IEC POWER INLET CONNECTOR -The Shenandoah™ Stereo 60LT uses a detachable power cord and
is shipped from the factory with the appropriate power inlet cable and connector for the market the amplifier was
shipped to. There is an AC mains fuse located in a small drawer within this molded connector.
PHANTOM POWER - An internal phantom power source (12 volts) is provided for use with condenser mics.
This power source is on at all times and does not affect the standard operation of the amp, even when a condenser
mic is not used. We use the DIN 45-596-P12 volt standard which will operate virtually all of the live sound
reinforcement condenser microphones on the market. Some “boutique” externally biased condenser mics will not
be compatible and will require 48 volt phantom power. We suggested live sound condenser mics by: AKG, Audio
Technica, Shure and Crown.
SPEAKER OUTPUT JACK - The Shenandoah™ Stereo 60LT provides left and right ¼” speaker output jacks.
Minimum total load is 4 ohms per side.
SPEAKER COMPLIMENT - The Shenandoah™ Stereo 60LT utilizes two specially designed 6.5” woofers and
dual compression tweeters. The cabinet features a front port for more rounded low frequency response. The
impedance of the internal speakers is 4 ohms per side.
MONITOR SHAPED CABINET DESIGN - The Shenandoah™ Stereo 60LT utilizes lightweight plywood to help
reduce weight. This cabinet design offers two platforms so the cabinet can be used in the normal upright position or
tipped back towards the performer for more of a monitoring situation. Leaning the cabinet back can change the tone of
the amp and reduce boomy low frequencies.
SPEAKER STAND MOUNT - A 1 1/2 “ speaker stand mount is provided for use with a speaker stand.
WARNING!
. The use and operation of this device constitutes an agreement of full release of any and all liability connected with
its use. Only persons familiar with the operation of high powered audio equipment should attempt to operate this
device.
. In addition, by use of this device, the user agrees to hold Genz Benz and its designers, sales agents, and all
other affiliates and related parties harmless in the event of any accident, injury, damage, or loss resulting from such
use.
. Manufacturer’s sole responsibility is to provide a warranty on the specified performance of the product under
normal operating conditions for a period of 3 years.
WARRANTY:
• Genz Benz warrants the model Shenandoah™ 60LT to be free from defects in materials and
workmanship for a period of 3 years from the date of purchase, when purchased from an authorized Genz Benz
dealer.
• This warranty does not cover normal wear and tear incurred from the normally designed use of the product.
• This warranty is effective only if a copy of the original sales receipt is presented at the time of warranty service.
• This limited warranty is completely transferable to any subsequent buyer as long as the original sales receipt is also
transferred to such subsequent buyer.
• All warranty service must be performed by a Genz Benz authorized service center.
• Before returning any unit for service, a returned merchandise authorization number (RMA#) must be obtained by
calling 480-941-0705
• This warranty is valid in the US and Canada only. For all products sold outside the USA, warranty is handled through
SAFE OPERATING REQUIREMENTS:
• Never set an amplifier on anything that will tip over or collapse under its weight.
• Provide a minimum distance of 25.4 mm (1 inch) around all sides of the amplifier for sufficient ventilation. The
ventilation should not be impeded by covering the amplifier’s vent openings with items such as newspapers, table
cloths, curtains, etc.
• No naked flame sources, such as lighted candles, should be placed on the Shenandoah™ 60LT amplifier.
• This amplifier should not be exposed to dripping or splashing and no objects filled with liquids, such as vases or
drinks, shall be placed on this product.
• The Shenandoah™ 60LT amplifier should be connected to a mains socket outlet (power receptacle) with
a protective earth (ground) connection at all times.
• The amplifiers mains plug (power plug) is considered the disconnect device and the connection must remain
accessible at all times.
• This amplifier is capable of producing sound pressure levels that may cause hearing loss.
• There are no user serviceable parts and hazardous operating voltages are present inside this unit. Always consult a
qualified repair facility for service.
SHENANDOAH™ STEREO 60LT
ENGINEERING SPECIFICATIONS
INPUTS
XLR Balanced input impedance:
XLR Balanced input sensitivity:
¼” Unbalanced input impedance:
¼” Unbalanced input sensitivity:
2.2 k ohms
-60 to -30 dBV
300 k ohms
-30 to +4 dBV
AMPLIFIER OUTPUT
Power at 4 ohm load:
THD + N (preamp):
30 watts per side RMS, 60 watts total
<0.035%
THD + N (power amp):
Frequency response:
<0.07%
20 Hz -20 kHz +/- 1dB
CHANNEL EQUALIZATION
Low frequency:
Mid frequency (sweep):
High frequency:
125 Hz shelving, +/-15dB
250 Hz - 5 kHz , peaking, +/-12dB
8 kHz shelving, +/-15dB
DIRECT OUTPUTS
XLR balanced output level:
XLR balanced output impedance:
¼” unbalanced output level:
¼” unbalanced output impedance:
-30 dBV nominal
150 ohms
+4 dBv nominal
1k ohm
DIGITAL EFFECTS
Processor type:
Internal processing:
A/D converter
WAVE FRONT™ STEREO DSP engine
24 bit
24 bit - 64X oversampling
24 bit - 128X oversampling
80 dB
D/A converter:
Dynamic Range:
THD + N (1 kHz)
Sampling rate:
<0.01%
48 kHz
Due to continuing product improvements and changes, all specifications are subject to change without notice.
Declaration of Conformity
(89/336 EEC-EMC Directive)
Manufacturer’s Name:
Manufacturer’s Address:
Genz Benz, a division of KMC Music Company
7811 East Pierce Street
Scottsdale, AZ 85287, U.S.A.
Product Type:
Audio Amplifier
Model Number:
Operating Power Condition:
Effective Date:
Shenandoah™ Stereo 60LT
100/115/230/240 V, 50/60 Hz
12-01-2007
Conforms to the Following Standards:
[X] EN 55013: 2001 + A1: 2003
[X] EN 55020: 2002 + A1: 2003
[X] EN 60065
[X] IEC 61000-3.3: 1994 + A1: 2001
[X] IEC 61000-4.2
[X] IEC 61000-4.3
[X] IEC 61000-4.4
[X] FCC -15.107 and 15.109
[X] RoHS Directive 2002/95/EC
[X] WEEE Directive 2002/96/EC
[X] CE Mark LV Directive 73/23 EEC
A KMC Music Company, Bloomfield, CT
7811 E. Pierce Street, Scottsdale, AZ 85257
PH: 480-941-0705 FAX: 480-946-2412
REV 5
|