Graco Inc Power Roller 245907 User Manual

Operating Instructions

309511

Rev. D

Parts

This manual contains important

warnings and information.

READ AND KEEP FOR REFERENCE.

INSTRUCTIONS

Pressure Roller Attachment

Model 245907, Series C

D 9 in. (23 cm) roller frame with 45_ angle and 12 in. reach

D 1/2 in. (13 mm) nap roller cover

3600 psi (24.8 MPa, 248 bar) Maximum Fluid Inlet Pressure

The best operating pressure is the lowest pressure that provides

an even paint supply to the roller and typically does not exceed

300 psi (2.1 MPa, 21 bar).

CAUTION

Never leave water in the pump, gun, or pressure roller.

Doing so could cause corrosion and damage from freezing.

For storage, flush the system with Graco Pump Armort or

mineral spirits/paint thinner.

GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441

Graco Inc. is registered to I.S. EN ISO 9001

Pressure Relief Procedure

3. Turn prime/spray valve to the PRIME to relieve

WARNING

pressure in system.

4. Remove gun trigger safety latch. Trigger gun to

To help prevent injection injuries,

follow this procedure whenever

you stop painting.

relieve any pressure in hose.

5. Engage gun trigger safety latch. Keep pump

prime/spray valve in PRIME position until you paint

again.

psi/MPa/bar

1. Engage gun trigger safety latch.

2. Shut off power to pump.

309511

Operation

1. Follow pump priming instructions prior to

10. Remove gun trigger safety latch. Trigger gun.

assembling roller.

Roll surface.

2. Do not put tip and guard on spray gun.

3. Turn prime/spray valve to SPRAY.

NOTE: Trigger the gun briefly only when you need

more paint. Determine how often you must trigger

the gun to maintain an even paint supply to the

roller.

4. Turn pressure control to lowest setting or roller

symbol. Fig. 1.

The best operating pressure is the lowest pressure

that provides an even paint supply to the roller and

typically does not exceed 300 psi (2.1 MPa, 21

bar).

11. Increase pump pressure only if triggering gun

cannot supply enough paint for your rolling speed.

Pressure Relief

Procedure, page 3.

Fig. 1

12. Whenever you stop painting, relieve the

pressure, and elevate roller end of extension tube

to prevent paint from draining out.

5. Remove gun trigger safety latch. Trigger the gun

once until paint comes out of gun. Release

trigger.

Flush the pump, gun, and pressure roller immediately

after each use to prevent paint from drying in the

pressure roller and damaging it. (Cleaning, page 6).

6. Engage gun trigger safety latch.

7. Assemble the pressure roller as shown in the Parts

Drawing, page 7. Make sure the gasket (6) is in

place in bottom of roller frame as shown.

8. Attach pressure roller assembly to spray gun.

9. Rest roller on flat surface and align gun with roller.

Tighten nut with wrench while keeping gun and

roller aligned as pictured below.

309511

Rolling Techniques

1. Rolling vertically, roll out the letter “M”. (Fig. 2.)

3. Finish with light, vertical strokes until the entire

area has been covered, evenly. (Fig. 4.)

Fig. 2

2. Cross roll, horizontally, to spread paint. (Fig. 3.)

Fig. 4

Fig. 3

Ceilings, Walls, and Woodwork

1. Ceilings: Using a paint brush, apply a starting

1. Woodwork & Walls: Using a brush, paint

woodwork first. Apply a starting row of paint

approximately the width of the paint brush around

the woodwork and where the walls meet the

ceiling. (Fig. 7.)

row of paint approximately the width of your paint

brush where the walls and ceiling meet. (Fig. 5.)

Fig. 5

2. With the roller, apply paint to the ceiling, working

the short way of the room and applying as wide a

strip as possible. (Fig. 6.)

Fig. 7

2. With the roller, apply paint to the walls, following

the Roller Techniques described above. (Fig. 8.)

Fig. 6

Fig. 8

309511

Cleaning

This is the procedure for flushing the pressure roller. The pump and gun you are using may have additional flushing

steps, such as cleaning filters and screens. See the pump and gun flushing instructions.

NOTE: Leave the pressure roller attached to the gun for this procedure.

4. Place roller frame (1) in paint pail. Be sure the

Pressure Relief

Procedure, page 3.

holes in roller frame (1) are facing inside the paint

pail.

5. Prime pump with water or flushing fluid for

oil–based materials. Use the lowest pump priming

pressure setting.

1. Relieve the pressure.

2. Remove roller cover (7) and diffuser (4) from roller

frame as follows (Parts Drawing, page 7):

6. Turn prime/spray valve to SPRAY.

a. Using your thumb, press down on clip (5) to

release end caps (2 & 3), diffuser (4) and roller

cover (7) into a pail.

NOTE: Perform Step 7 at the lowest pressure

possible.

7. Trigger gun until flushing fluid begins to dilute the

b. Remove roller cover (7) from diffuser (4).

paint.

c. Pull end caps (2 & 3) off diffuser (4).

Disassemble.

8. Place roller frame (1) in another bucket and

continue flushing until fluid coming out of the roller

frame (1) is clear.

3. Clean roller cover (7), caps (2 &3) and diffuser (7)

with water or a compatible fluid for oil–based

materials.

9. Shut off the pump. Turn prime/spray valve to

PRIME.

Storage

If you are going to store the airless equipment for an extended period of time after flushing with water-base fluid,

flush again with Graco Pump Armor or mineral spirits/paint thinner. Leave the fluid in the system during storage.

309511

Roller Parts

6, 9

ti2135b

Parts List

Ref.

No.

Additional Roller Covers

Part No. Description

Qty.

For the best coverage it is important to choose the

right roller cover nap for the surface you are rolling.

For rougher surfaces choose a thicker nap. Use a

thinner nap on smooth surfaces.

FRAME, roller

245999

246277

15B065

CAP, end (includes seal and retainer)

DIFFUSER

o–ring)

CLIP, roller

GASKET

Part No. Nap Size

Surface Texture/ Material

Example

197106

115524

9 in. (23 cm);

1/2 in. (13 mm) wood, trim, drywall

Smooth/ metal,

medium

243063

243064

243065

186678

ROLLER, cover, 9 inch,

1/2 in. (13 mm) nap

9 in. (23 cm);

3/4 in. (19 mm) cement, brick

Rough/

heavy

197118

SWIVEL, fitting

9 in. (23 cm);

1-1/4 in. (32

mm)

Extra–rough/

cement block, tex-

tured walls, ceil-

ings

heavy

309511

Limited Warranty

Graco Inc. warrants to the original retail purchaser (other than for purposes of resale or rental) all equipment

manufactured by Graco and bearing its name to be free from defects in material and workmanship if operated

in accordance with Graco’s printed recommendations and instructions. This warranty applies for one year from

the date of purchase.

This warranty does not cover and Graco shall not be liable for general wear and tear, or any malfunction,

damage or wear caused by improper use, accidents, user negligence, use of non-Graco component parts or

service or repair performed by anyone other than a Graco authorized service center.

IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE, ARE LIMITED TO ONE YEAR FROM THE DATE OF ORIGINAL PURCHASE.

GRACO SHALL NOT IN ANY EVENT BE LIABLE FOR ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL

LOSS, DAMAGE OR EXPENSE OF ANY KIND, WHETHER FROM BREACH OF THIS WARRANTY OR ANY

OTHER REASON. Some states do not allow the exclusion or limitation of incidental or consequential damages,

so the above limitation or exclusion may not apply to you.

To make a claim under this warranty, return the product with proof of purchase, transportation prepaid, to any

Authorized Graco Service Center. Graco’s Authorized Service Center, at its option, will either repair or replace

the product and return it to you, postage prepaid. A listing of Authorized Graco Service Centers is enclosed

with this product. You may also find the nearest Authorized Graco Service Center by calling 1–888–541–9788

or by visiting our website at www.graco.com.

This warranty gives you specific legal rights and you may also have other rights which may vary from state to

state.

All written and visual data contained in this document reflect the latest product information available at the time of publication.

Graco reserves the right to make changes at any time without notice.

GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441

www.graco.com

PRINTED IN USA 309511 4/2002, Revised 4/2003

309511

Graco Septic System 241407 User Manual
Hamilton Beach Iron 840124300 User Manual
Hasbro Video Game Console 7 832 User Manual
Hasselblad Camera Lens CFE 28 80 User Manual
Hotpoint Washer WF840 User Manual
HP Hewlett Packard Printer 2025n User Manual
Hunter Fan Fan 22925 User Manual
Husqvarna Brush Cutter 371K User Manual
Ice O Matic Ice Maker EF Series User Manual
Impex Exercise Bike H2502C User Manual