Graco Inc Pressure Washer 226314 User Manual

INSTRUCTIONS-PARTS LIST  
306926  
Rev. L  
This manual contains important  
warnings and information.  
READ AND KEEP FOR REFERENCE.  
First choice when  
quality counts.t  
INSTRUCTIONS  
10:1 RATIO BULLDOG, PORTABLE, STAINLESS STEEL RUBBER PACKED  
Hydra-CleanR Pressure Washer  
1000 psi (6.9 MPa, 69 bar) Maximum Working Pressure  
Model 226314, Series G  
06648B  
CAUTION  
The Graco warranty will not apply if cleaning solutions other  
than those recommended by Graco are used in these units.  
Only use solutions that are not harmful to the wetted parts.  
See the Technical Data on page 9.  
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441  
ECOPYRIGHT 1996, GRACO INC.  
Graco Inc. is registered to I.S. EN ISO 9001  
 
WARNING  
INJECTION HAZARD  
Spray from the gun, leaks or ruptured components can inject fluid into your body and cause extremely  
serious injury, including the need for amputation. Fluid splashed in the eyes or on the skin can also  
cause serious injury.  
D Fluid injected into the skin is a serious injury. The injury may look like just a cut, but it is a serious  
injury. Get immediate medical attention.  
D Do not point the gun at anyone or at any part of the body.  
D Do not put your hand or fingers over the spray tip.  
D Do not stop or deflect leaks with your hand, body, glove or rag.  
D Always have the tip guard and the trigger guard on the gun when spraying.  
D Be sure the gun trigger safety operates before spraying.  
D Lock the gun trigger safety when you stop spraying.  
D Follow the Pressure Relief Procedure on page 6 if the spray tip clogs and before cleaning,  
checking or servicing the equipment.  
D Tighten all fluid connections before operating the equipment.  
D Check the hoses, tubes, and couplings daily. Replace worn, damaged, or loose parts immediately.  
FIRE AND EXPLOSION HAZARD  
Improper grounding, poor ventilation, open flames or sparks can cause a hazardous condition and re-  
sult in a fire or explosion and serious injury.  
D Ground the equipment and the object being sprayed. Refer to Grounding on page 4.  
D If there is any static sparking or you feel an electric shock while using this equipment, stop spray-  
ing immediately. Do not use the equipment until you identify and correct the problem.  
D Provide fresh air ventilation to avoid the buildup of flammable fumes from solvents or the fluid  
being sprayed.  
D Keep the spray area free of debris, including solvent, rags, and gasoline.  
D Before operating this equipment, electrically disconnect all equipment in the spray area.  
D Before operating this equipment, extinguish all open flames or pilot lights in the spray area.  
D Do not smoke in the spray area.  
D Do not turn on or off any light switch in the spray area while spraying or while operating if fumes  
are present.  
D Do not operate a gasoline engine in the spray area.  
MOVING PARTS HAZARD  
Moving parts, such as the air motor piston, can pinch or amputate your fingers.  
D Keep clear of all moving parts when starting or operating the pump.  
D Never operate the pump with the air motor plates removed.  
D Before checking or servicing the equipment, follow the Pressure Relief Procedure on page 6 to  
prevent the equipment from starting unexpectedly.  
306926  
3
 
Installation  
3. Air and fluid hoses: use only electrically conductive  
Grounding  
hoses.  
WARNING  
FIRE AND EXPLOSION HAZARD  
Before operating the pump, ground the  
system as explained below. Also read  
the section FIRE AND EXPLOSION  
HAZARD on page 3.  
4. Air compressor: follow manufacturers recommen-  
dations.  
5. Spray gun: ground through connection to a prop-  
erly grounded fluid hose and pump.  
Although water generally provides a natural electrical  
ground, the following equipment must be grounded if  
the cleaning chemicals are volatile.  
6. Fluid supply container: follow your local code.  
7. Object being sprayed: follow your local code.  
1. When cleaning in enclosed areas, such as storage  
tanks, locate the pump and air compressor outside  
the area and well away from it. Provide adequate  
ventilation. If the area you are cleaning has stored  
flammable materials. take appropriate precautions  
to avoid static sparking. Consult your local codes.  
8. Solvent pails used when flushing: follow your local  
code. Use only metal pails, which are conductive,  
placed on a grounded surface. Do not place the  
pail on a nonconductive surface, such as paper or  
cardboard, which interrupts the grounding continu-  
ity.  
2. Pump: use a ground wire and clamp. See Fig. 1.  
Remove the ground screw (Z) and insert through  
the eye of the ring terminal at end of ground wire  
(Y). Fasten the ground screw back onto the pump  
and tighten securely. Connect the other end of the  
wire to a true earth ground. Order Part No. 222011  
Ground Wire and Clamp.  
9. To maintain grounding continuity when flushing or  
relieving pressure, hold a metal part of the spray  
gun firmly to the side of a grounded metal pail,  
then trigger the gun.  
Z
Y
General Information  
The typical setup shown in Figure 2 is only a guide to  
selecting and installing required and optional compo-  
nents. For assistance in designing a system to suit  
your needs, contact your Graco representative. Refer  
to Figure 2 for callouts in parentheses.  
TI1052  
Fig. 1  
4
306926  
 
Installation  
E
D
F
24  
47  
18  
E
C
2
10  
16  
28  
B
22  
35  
A
06649B  
Fig. 2  
Refer to the separate instructions, supplied, for instruc-  
tions on filling and adjusting the air line lubricator.  
Pump Setup  
See Fig. 2. Connect the suction hose (28) between the  
pump inlet (A) and the suction tube (18), using thread  
sealant on the male threads. Screw on the suction  
tube filter (B). Place the suction tube in the supply  
drum, and adjust it so it is 1 in. (25 mm) off the bottom  
of the drum. Tighten the thumbscrew (2) of the pipe  
hanger onto the drum.  
Close the air shutoff valve (E). Then, connect a 3/4 in.  
ID (minimum) air supply hose (D) to the 3/4 npt (m) air  
manifold (F) swivel.  
Ground the system as described on page 4.  
Connect the spray hose (22) to the pump outlet man-  
ifold (16). For two gun spraying, remove the plug (10)  
in the manifold and connect another spray hose.  
Connect the spray gun (35) to the hose (22). Use  
thread sealant on the male threads.  
An important step in installing this sprayer is to read  
and understand each of the instruction manuals sup-  
plied with sprayer. These manuals contain additional  
warnings, cautions, and detailed instructions about  
installing, operating, and servicing the various system  
components.  
Fill the displacement pump wet-cup (C) 1/2 full with  
Throat Seal Liquid, or a compatible solvent.  
306926  
5
 
Operation  
Pressure Relief Procedure  
Pump Operation  
Prepare the cleaning solution according to the  
manufacturers instructions. For your own safety, be  
sure to observe all warnings. If you are using pow-  
dered cleaners, mix them thoroughly in a separate pail  
before adding them to a supply drum. Undissolved  
powders are extremely abrasive and may damage  
pump parts.  
WARNING  
INJECTION HAZARD  
Fluid under high pressure can be in-  
jected through the skin and cause seri-  
ous injury. To reduce the risk of an injury  
from injection, splashing fluid, or moving parts, fol-  
low the Pressure Relief Procedure whenever you:  
D are instructed to relieve the pressure,  
D stop spraying,  
WARNING  
D check or service any of the system equipment,  
D or install or clean the spray tips.  
Wear appropriate protective clothing, such as  
waterproof outerwear and eye goggles, according  
to the cleaner manufacturers recommendations.  
Cleaning chemicals may be toxic, and cause  
serious irritation to your eyes or skin.  
1. Lock the gun trigger safety.  
2. Close the air regulator.  
3. Close the bleed-type master air valve (E).  
4. Unlock the gun trigger safety.  
See Fig. 2. To start the pump, close the bleedtype  
master air valve (E), close the air regulator (24) by  
turning the T-handle all the counterclockwise until the  
spring tension is relieved. Open the shutoff valve, hold  
a metal part of the gun firmly to the side of a grounded  
metal pail, trigger the gun, and slowly open the regula-  
tor until fluid comes from the gun. Release the trigger;  
the pump will stall against pressure.  
5. Hold a metal part of the gun firmly to the side of a  
grounded metal pail, and trigger the gun to relieve  
pressure.  
6. Lock the gun trigger safety.  
7. Open the drain valve (required in your system),  
having a container ready to catch the drainage.  
When supplied with an adequate air pressure and  
volume, the pump will start and stop as the gun is  
opened and closed.  
8. Leave the drain valve open until you are ready to  
spray again.  
If you suspect that the spray tip or hose is completely  
clogged, or that pressure has not been fully relieved  
after following the steps above, very slowly loosen the  
tip guard retaining nut or hose end coupling and relieve  
pressure gradually. Then, loosen completely. Clear the  
tip or hose obstruction.  
Use the air regulator (24) to control pump speed and  
fluid pressure. Always use the lowest pressure neces-  
sary to get the desired result. Higher pressures will  
waste the material and cause early spray tip and pump  
wear.  
6
306926  
 
Operation  
Always stop the pump at the bottom of its stroke to  
WARNING  
prevent material from drying on the rod and damaging  
the packings.  
To reduce the risk of overpressurizing the sprayer,  
NEVER exceed 1000 psi (6.9 MPa, 69 bar) Maxi-  
mum Working Pressure. If you add any accesso-  
ries to the fluid line, be sure they are rated for at  
least 1000 psi (6.9 MPa, 69 bar) working pressure.  
CAUTION  
Never let the pump run dry. A pump that is running  
too fast can damage itself. Shut the pump off imme-  
diately, then check and refill the supply container to  
prevent air from being sucked into the system, keep  
liquid in the supply container at all times.  
Adjust the air line lubricator to about two drops per  
minute through the sight glass when the pump is  
running. Refer to the separate instruction manual,  
supplied, for adjustment instructions.  
WARNING  
Useful Hints  
Check the bleedtype master air valve (E) weekly  
to be sure it relieves all air in the motor when in the  
closed position. If it is not completely relieved, the  
pump could cycle unexpectedly and cause serious  
injury. Replace the valve immediately it it is, or  
appears to be faulty.  
WARNING  
To reduce the risk of serious injury whenever you  
are instructed to relieve pressure, always follow the  
Pressure Relief Procedure on page 6.  
Shutdown and Care of the Sprayer  
Protect surfaces that may be damaged by the cleaning  
solution. Rinse the solution off before it dries.  
WARNING  
To reduce the risk of serious injury whenever you  
are instructed to relieve pressure, always follow the  
Pressure Relief Procedure on page 6.  
Hold the spray nozzle about 2 feet (2/3 meter) from the  
surface and completely mist-wet the object you are  
cleaning. Let the object soak briefly, then use the  
spray to chiselthe dirt off. Keep the nozzle about  
6 in. (153 mm) from and at an angle to the surface. If  
some dirt remains, wet the surface again, let it soak a  
little longer, then hold the nozzle close to the surface to  
blast the dirt off. A heated cleaning solution may work  
better; check with your cleaner manufacturer.  
Check the air line lubricator to ensure that it contains  
enough oil.  
Relieve the pressure, and check the displacement  
pump packing nut adjustment often. The packing nut  
should be tight enough to stop leakage, but no tighter.  
After all dirt is cleaned off, rinse all the solution off with  
clean, cold water. Relieve the pressure whenever you  
stop spraying.  
Keep the displacement pump wet-cup (C) 1/2 full at all  
times. The TSL helps protect the pump packings. See  
Fig. 2.  
306926  
7
 
Troubleshooting  
NOTE: Refer to the separate instruction manuals  
which are supplied with this sprayer, and the manuals  
which are supplied with any accessories you added,  
for complete operation, troubleshooting and repair  
instructions.  
WARNING  
To reduce the risk of serious injury whenever you  
are instructed to relieve pressure, always follow the  
Pressure Relief Procedure on page 6.  
NOTE: Check all possible problems and solutions  
before disassembling the unit.  
NOTE: Relieve the pressure before checking or  
servicing the equipment.  
Problem  
Cause  
Solution  
Insufficient air supply  
See performance chart on page 9.  
Will not spray  
Closed or clogged air regulator, valve, Open, clear.  
supply line, etc.  
Obstructed spray tip, valve, or hose  
Worn or damaged pump parts  
Clogged fluid intake filter  
Clear, use larger tip.  
See manual 306818 or 306821.  
Clean.  
Valve will not stop pump operation  
Exhausted cleaning solution supply  
Worn or damaged pump parts  
Incorrect valve adjustment  
Refill.  
See manual 306818 or 306821.  
Adjust; see manual 307010.  
Clear, replace; see manual 307010.  
Valve will not stop fluid spray  
Obstructed or worn valve stem or  
seat  
Closed or clogged air regulator, valve, Open, clear.  
supply line, etc.  
Fluid leaking from valve at needle  
Worn needle packings or loose pack- Tighten; see manual 307010  
ing nut  
Insufficient air supply  
See performance chart on page 9.  
Fluid will not come from pump  
(hose removed)  
Closed or clogged air regulator, valve, Open, clear.  
supply line, etc.  
Obstructed spray tip, valve, or hose  
Clogged fluid intake filter  
Clear, use larger tip.  
Clean.  
Exhausted cleaning solution supply  
Worn or damaged pump parts  
Obstructed spray tip, valve, or hose  
Exhausted cleaning solution supply  
Worn or damaged pump parts  
Spray valve swivel packings worn  
Refill.  
See manual 306818 or 306821  
Clear, use larger tip.  
Refill.  
Pump operating, but output low  
Fluid leaking from valve handle  
See manual 306818 or 306821  
Replace; see manual 307010  
8
306926  
 
Pump Performance Chart  
7 cycles per gallon (3.8 liter)  
Maximum recommended continuous speed: 60 cycles/min: 8 gpm (29 liter/min)  
40 psi (0.3 MPa, 3 bar)  
AIR SUPPLY TO PUMP  
70 psi (0.5 MPa, 5 bar)  
AIR SUPPLY TO PUMP  
100 psi (0.7 MPa, 7 bar)  
AIR SUPPLY TO PUMP  
SPRAY TIP  
ORIFICE  
SIZE  
GPM  
CFM  
GPM  
CFM  
GPM  
CFM  
(l/min) (m#/min)  
WP  
(l/min) (m#/min)  
WP  
(l/min) (m#/min)  
WP  
0.065 in.  
1.7  
10  
340 psi  
2.3  
24  
590 psi  
2.7  
38  
825 psi  
(1.65 mm)  
(6.6)  
(0.28)  
(2.4 MPa, 24 bar)  
(8.9)  
(0.67)  
(4.0 MPa, 40 bar)  
(10.2)  
(1.06)  
(5.7 MPa, 57 bar)  
0.078 in.  
(1.98 mm)  
2.9  
(11.2)  
17  
(0.48)  
330 psi  
(2.3 MPa, 23 bar)  
3.8  
(14.6)  
38  
(1.06)  
560 psi  
(3.8 MPa, 38 bar)  
4.5  
(17.0)  
60  
(2.08)  
800 psi  
(5.5 MPa, 55 bar)  
0.094 in.  
(2.39 mm)  
4.2  
(16.3)  
25  
(0.70)  
320 psi  
(2.2 MPa, 22 bar)  
5.4  
(20/9)  
54  
(1.51)  
540 psi  
(3.7 MPa, 37 bar)  
6.5  
(24.5)  
83  
(2.32)  
760 psi  
(5.2 MPa, 52 bar)  
0.109 in.  
(2.77 mm)  
5.4  
(20.9)  
33  
(0.92)  
300 psi  
(2.1 MPa, 21 bar)  
7.3  
(28.3)  
7.3  
(28.3)  
510 psi  
(3.5 MPa, 35 bar)  
8.5  
(32.2)  
95  
(2.66)  
700 psi  
(4.8 MPa, 48 bar)  
KEY TO PERFORMANCE CHART  
GPM: Gallons Per Minute  
CFM: Cubic Feet Per Minute  
PSI: Pounds Per Square Inch  
WP: Working Pressure in psi  
Technical Data  
Air Operating Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40100 psi (0.30.7 MPa, 37 bar)  
Pump cycles per gallon (3.8 liter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7  
Maximum recommended pump speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 cycles per minute: 8 gpm (29 liter/min)  
Recommended speed for optimum pump life . . . . . . . . . . . . . . . . . . . . . . . . . 20 cycles per minute: 3 gpm (11 liter/min)  
Air consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See chart above  
Pump discharge pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See chart above  
Fluid hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.38 in. (9.7 mm) ID; 3 wire braid; 40(12.2 m) lg;  
3/8 npt(m) stainless steel couplings; 2250 psi  
(15.6 MPa, 156 bar) maximum working pressure  
R
Spray gun. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pistol grip with PTFE packings and 10 in. (254 mm)extension tube  
1000 psi (6.9 MPa, 69 bar) maximum working pressure  
Intake filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 mesh wire screen; brass body  
Wetted parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Type 302, 303, 304 & 316 Stainless Steel; Brass; Nitrile Rubber  
R
306926  
9
 
Parts  
Detail A  
Detail B  
24  
48  
47  
30  
33  
46  
32  
34  
21  
26  
1c  
1e, 1f, 1g  
Detail B  
1d  
17  
23  
2
10  
16  
31  
28  
1
1a  
1b  
18  
15  
35  
29  
22  
Detail A  
42  
19  
7663B  
10  
306926  
 
Parts  
Model 226314, Series G  
10:1 Bulldog Portable Hydra-Clean Unit  
Ref.  
Ref.  
No.  
Part No.  
Description  
Qty.  
No.  
Part No.  
206797  
237522  
Description  
Qty.  
1
244530  
CART ASSY, global  
Includes items 1a1g  
. WHEEL  
. RING, retaining  
. CAP  
26  
10:1 BULLDOG PUMP;  
See manual 306821 for parts  
HOSE, coupled; nylon; 1 in. (25 mm)  
ID; cpld 111 1/2 npt(m);  
6(1.8 m) long  
SPRAY VALVE EXTENSION ASSY;  
Includes item 30, 32, 33, 34  
. TUBE, extension; 1/4 npt(m);  
10 in. (254 mm) long  
SWIVEL  
1
2
2
2
1
4
4
4
1
1
1
1
1a  
1b  
1c  
1d  
1e  
1f  
1g  
2
10  
15*  
16  
113362  
113436  
113361  
191605  
100131  
100133  
100004  
100085  
101748  
165447  
166444  
28  
1
1
. BRACKET  
. NUT, hex; 3/816  
29  
30  
207299  
164017  
. WASHER, lock; 3/8  
. SCREW, cap, hex hd  
SCREW, thumb; 0.2520 x 0.5 in.  
PLUG, pipe; 3/8 npt  
FILTER, fluid intake; 1 in. npt(f)  
MANIFOLD, outlet; 1 in. npt(m) x  
3/8 npt(f)  
COUPLING, hex pipe; 1 in. npt  
TUBE, suction; 1 in. npt(mbe);  
max. adj. height 30 in. (0.76 m)  
ELBOW, street; reducing;  
11/2 npt (m) x 1 in. npt (f)  
HOSE, coupled  
HOSE, fluid cpld 3/8 npt(m), 40 ft  
(12.2 m) lg. Buna-N; 3/8 in. ID  
HANGER, pipe  
1
1
31  
32*  
103977  
103921  
TIP, spray, 40_ fan angle; .065 in.  
(1.65 mm) orifice  
1
1
1
33  
34  
35  
175019  
220220  
237485  
BODY, nozzle  
GUARD, tip  
SPRAY GUN  
See manual 307010 for parts  
GROUND WIRE ASSY  
UNION, swivel  
VALVE, safety relief  
LUBRICATOR, air  
1
1
17  
18  
166629  
166630  
1
1
1
1
1
1
1
41  
42  
46  
47  
48  
244524  
235208  
113498  
C11034  
116522  
19  
180180  
1
1
21  
22*  
238374  
205753  
CONNECTOR, air control  
1
1
23  
24  
205770  
244720  
* Recommended Tool Box spare parts. Keep these spare  
parts on hand to reduce down time.  
AIR REGULATOR  
See manual 309341 for parts  
1
306926  
11  
 
Graco Standard Warranty  
Graco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on the  
date of sale by an authorized Graco distributor to the original purchaser for use. With the exception of any special, extended, or limited  
warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment  
determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accor-  
dance with Gracos written recommendations.  
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by  
faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or sub-  
stitution of nonGraco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of  
Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture,  
installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.  
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for  
verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The  
equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect  
in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and  
transportation.  
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT  
NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.  
Gracos sole obligation and buyers sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other  
remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any  
other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the  
date of sale.  
Graco makes no warranty, and disclaims all implied warranties of merchantability and fitness for a particular purpose in connection  
with accessories, equipment, materials or components sold but not manufactured by Graco. These items sold, but not manufactured  
by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide  
purchaser with reasonable assistance in making any claim for breach of these warranties.  
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment  
hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,  
breach of warranty, the negligence of Graco, or otherwise.  
FOR GRACO CANADA CUSTOMERS  
The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings  
entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnais-  
sent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires  
exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procedures concernées.  
Graco Phone Numbers  
TO PLACE AN ORDER, contact your Graco distributor, or call one of the following numbers  
to identify the distributor closest to you:  
18003674023 TollFree  
6126236921  
6123783505 Fax  
All written and visual data contained in this document reflects the latest product information available at the time of publication.  
Graco reserves the right to make changes at any time without notice.  
Sales Offices: Minneapolis, Detroit  
International Offices: Belgium, Korea, Hong Kong, Japan  
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 554401441  
PRINTED IN U.S.A. 306926 January 1967 Revised October 2001  
12  
306926  
 

Graco Network Router 312353B User Manual
Gravely Lawn Mower 985103 User Manual
Haier Cell Phone W716 User Manual
Haier Microwave Oven AED 2485EG User Manual
Hawking Technology Network Router HWU8DD User Manual
HP Hewlett Packard Stereo Equalizer E0601 User Manual
HP Hewlett Packard Swimming Pool Gate Alarm Agilent 4194A User Manual
HTC Cell Phone F5151 User Manual
Husqvarna Snow Blower 96193005301 User Manual
Image Treadmill IMTL11990 User Manual