12V CORDLESS VACUUM
MODEL H0602
INSTRUCTION MANUAL
COPYRIGHT © 2000 BY GRIZZLY INDUSTRIAL, INC.
1821 VALENCIA ST., BELLINGHAM, WA 98227
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
PRINTED IN CHINA
Safety Instructions For Power Tools
9. USE PROPER EXTENSION CORD
14. MAINTAIN TOOLS WITH CARE.
for the charger. Make sure your
extension cord is in good condition.
Conductor size should be in accor-
dance with the chart below. The
amperage rating should be listed on
the motor or tool nameplate. An
undersized cord will cause a drop in
line voltage resulting in loss of power
and overheating. Your extension
cord must also contain a ground wire
and plug pin. Always repair or
replace extension cords if they
become damaged.
Keep tools sharp and clean for best
and safest performance. Follow
instructions for lubricating and
changing accessories.
15. DISCONNECT TOOLS before ser-
vicing and changing accessories,
such as blades, bits, cutters, and
the like.
16. REDUCE THE RISK OF UNINTEN-
TIONAL STARTING. Make sure
switch is in off position before plug-
ging in.
17. USE RECOMMENDED ACCES-
SORIES. Consult the owner’s man-
ual for recommended accessories.
The use of improper accessories
may cause risk of injury.
Minimum Gauge for Extension Cords
AMP
RATING
0-6
LENGTH
50ft
16
25ft
18
18
16
14
12
10
100ft
16
14
14
12
18. CHECK
DAMAGED
PARTS.
7-10
16
16
12
12
Before further use of the tool, a
guard or other part that is damaged
should be carefully checked to
determine that it will operate proper-
ly and perform its intended function.
Check for alignment of moving
parts, binding of moving parts,
breakage of parts, mounting, and
any other conditions that may affect
its operation. A guard or other part
that is damaged should be properly
repaired or replaced.
11-12
13-16
17-20
21-30
10
No
10
10. WEAR PROPER APPAREL. Do not
wear loose clothing, gloves, neck-
ties, rings, bracelets, or other jewel-
ry which may get caught in moving
parts. Non-slip footwear is recom-
mended. Wear protective hair cover-
ing to contain long hair.
11. ALWAYS USE SAFETY GLASSES.
Also use face or dust mask if cutting
operation is dusty. Everyday eye-
glasses only have impact resistant
lenses, they are NOT safety glass-
es.
No list of safety guidelines can be
complete. Every shop environment is
different. Always consider safety
first, as it applies to your individual
working conditions. Use this and
other machinery with caution and
respect. Failure to do so could result
in serious personal injury, damage to
equipment or poor work results.
12. SECURE WORK. Use clamps or a
vise to hold work when practical. It’s
safer than using your hand and frees
both hands to operate tool.
13. DON’T OVERREACH. Keep proper
footing and balance at all times.
-2-
H0602 12V Cordless Vacuum
ADDITIONAL SAFETY
1. Read all instructions and warn-
7. If charger light fails to come on
check the incoming power supply. If
power source is okay, then the fuse
inside the charger needs replace-
ment. Charger should be serviced
by a qualified electrical technician
only.
ings on the battery and charger
before charging the battery.
2. Charge only using the supplied
charger and battery. Do not use
with other batteries, chargers or trim
saws.
8. Charger plug has a polarized
plug (one prong is wider than the
other). Do not attempt to modify the
plug. Modifying the plug will result
in a safety hazard and will void the
warranty.
3. Do not expose battery or charger
to wet or rainy conditions.
Moisture greatly increases the risk
of a shock hazard.
4. Do not touch battery poles with
any conductive materials. Touching
any two poles at the same time
causes a short condition and can
cause sparks or electrical shock.
9. Charger is designed to operate at
110-120 volts. Never try to plug
into any circuit that is not 110-120
volts. Never modify or change the
plug that is attached to the charger
unit to attempt to plug into 220 volt.
This can cause serious electrical
damage to the unit, possible fire or
explosion.
5. Do not store battery with conduc-
tive materials. Storing the battery
in a box of screws or nails can
cause shorting across the battery
poles.
6. Do not throw battery in fire.
Combustion of some of the batter-
ies’ component materials can cause
toxic fumes and possible explosion.
BATTERY MUST BE RECYCLED OR DISPOSED
OF PROPERLY. Consult your local Yellow Pages
directory under the category “Recycling” to locate a
battery recycler in your area.
-3-
H0602 12V Cordless Vacuum
INTRODUCTION
Commentary
We are proud to offer the Grizzly Model
H0602 12V Cordless Vacuum. The Model
H0602 is part of a growing Grizzly family
of fine power tools. When used according
to the guidelines set forth in this manual,
you can expect years of trouble-free,
enjoyable operation and proof of Grizzly’s
commitment to customer satisfaction.
The specifications, details, and pho-
tographs in this manual represent the
Model H0602 as supplied when the manu-
al was prepared. However, owing to
Grizzly’s policy of continuous improve-
ment, changes may be made at any time
with no obligation on the part of Grizzly. If
you have any comments regarding this
manual, please write to us at the address
below:
The Model H0602 12V Cordless Vacuum
is equipped with a high velocity motor
capable of handling many clean-up jobs.
The large collection chamber requires no
special bags and is easy to empty.
Vacuum also includes a 12V charging sta-
tion.
Grizzly Industrial, Inc.
Technical Documentation
P.O. Box 2069
C
/O
Bellingham, WA 98227-2069
Most importantly, we stand behind our
tools. If you have any service questions or
parts requests, please call or write us at
the location listed below.
We are pleased to provide this manual
with the Model H0602. It was written to
encourage safety considerations and
guide you through general operating pro-
cedures and maintenance. It represents
our effort to produce the best documenta-
tion possible.
Grizzly Industrial, Inc.
2406 Reach Road
Williamsport, PA 17701
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail: [email protected]
The Model H0602 was specifically
designed for vacuuming dust, dirt
and other small debris. Do not mod-
ify and/or use this machine for any
other purpose. Modifications or
improper use of this tool will void
the warranty. If you are confused
about any aspect of this machine,
DO NOT use it until you have
answered all your questions.
Serious personal injury may occur.
Never leave a battery unattend-
ed while charging. While charg-
ing will make the battery and
charging unit warm, if it
becomes hot to the touch, dis-
connect the charger immediate-
ly. There is a possibility of fire
hazard. Have the battery and
charging unit checked by a qual-
ified electrical service techni-
cian.
-4-
H0602 12V Cordless Vacuum
OPERATIONS
Getting Started
First review the contents of your cordless
tool kit and familiarize yourself with the key
components.
3. Occasionally remove and clean the
elastic filter sleeve from the inside of
the collection chamber. Allow filter to
completely dry before using the vacu-
um.
Cordless Vacuum
Battery Pack
Charging Stand
Keeping Tools Clean
The battery in your new cordless power
tool will not be fully charged when you
receive it. To maximize the storage capac-
ity of the battery it should be completely
discharged, then fully recharged 3-5 times.
Plastic parts can easily be cleaned with a
damp cloth, but never use water to clean
any electrical parts. Solvents should also
be avoided on plastic because of the pos-
sibility of damage.
For optimal life span, completely discharge
the battery before charging. Follow the
instructions below to charge your battery.
Maintenance
Battery charging with standard charger
(1 piece charger):
Your cordless power tool will give you hun-
dreds of hours of operation time before
ever needing service. The electrical com-
ponents of this cordless vacuum are not
user serviceable. Repair should always be
undertaken by a qualified electrical repair
technician.
1. Plug the charger into an appropriate
110/120V outlet.
2. Insert the battery into the charger.
The battery fits into the oval recess in
only one way. Do not force the bat-
tery. Insert until it locks into place.
3. The red light will come on when the
battery is inserted. Charge battery for
3-5 hours.
Always store the cordless vacuum in a dry
place.
4. When the battery is fully charged,
remove the battery from the charger
to complete of the charge cycle.
The battery will require periodic recharg-
ing, and eventually replacement after it has
exceeded its recharge life (approximately
800-1000 recharge cycles). You will notice
extended charging times or shortened
operation time as the battery experiences
more cycles. Refer to the Grizzly catalog
for replacement batteries.
Using Your Vacuum
1. Turn vacuum on by pressing the
switch at located on the top of the
unit.
2. Empty the collection chamber by
pressing the button located on the top
of the unit
-5-
H0602 12V Cordless Vacuum
WARRANTY AND RETURNS
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original
purchaser from the date of purchase. This warranty does not apply to defects due directly
or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main-
tenance. This is Grizzly’s sole written warranty and any and all warranties that may be
implied by law, including any merchantability or fitness, for any particular purpose, are here-
by limited to the duration of this written warranty. We do not warrant or represent that the
merchandise complies with the provisions of any law or acts unless the manufacturer so
warrants. In no event shall Grizzly’s liability under this warranty exceed the purchase price
paid for the product and any legal actions brought against Grizzly shall be tried in the State
of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental, con-
tingent, special, or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details.
We will then issue you a “Return Number’’, which must be clearly posted on the outside as
well as the inside of the carton. We will not accept any item back without this number. Proof
of purchase must accompany the merchandise.
The manufacturers reserve the right to change specifications at any time because they con-
stantly strive to achieve better quality equipment. We make every effort to ensure that our
products meet high quality and durability standards and we hope you never need to use this
warranty.
Please feel free to write or call us if you have any questions about the machine or the man-
ual.
Grizzly Industrial, Inc.
2406 Reach Road
Williamsport, PA 17701
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail:
Thank you again for your business and continued support. We hope to serve you again
soon.
-6-
H0602 12V Cordless Vacuum
WARRANTY CARD
Name__________________________________________________________
Street__________________________________________________________
City____________________State________Zip_________
Phone Number____________E-Mail___________________FAX____________
Model # H0602 12V Cordless Vacuum
Order #_______________________
The following information is given on a voluntary basis. It will be used for marketing purposes to help
us develop better products and services. Of course, all information is strictly confidential.
9. How many of the machines checked above are
Grizzly? ____________
1. How did you learn about us?
___Advertisement
___Friend
___Catalog
___World Wide Web
___Other__________________________
___Card Deck
10. Which portable/hand held power tools do you own?
Check all that apply.
___Belt Sander
___Biscuit Joiner
___Circular Saw
___Detail Sander
___Drill/Driver
___Orbital Sander
___Palm Sander
___Portable Planer
___Saber Saw
___Reciprocating Saw
___Router
2. What is your annual household income?
___$20,000-$29,999
___$30,000-$39,999
___$40,000-$49,999
___$50,000-$59,999
___$60,000-$69,999
___$70,000-$79,999
___$80,000-$89,999
___$90,000 +
___Miter Saw
___Other_________________________________
3. What is your age group?
___20-29
11. What machines/supplies would you like Grizzly
Industrial to carry?
___50-59
___60-69
___70 +
___30-39
___40-49
___12" Table Saw
___12" Jointer
___Radial Arm Saw
___Panel Saw
___Lumber
___Brass Hardware
4. How long have you been a woodworker?
___Paint & Finishing Supplies
___Contractor’s Supplies
___0 - 2 Years
___2 - 8 Years
___8 - 20 Years
___20+ Years
___Combination Planer/Jointer
___Other_________________________________
5. How would you rank your woodworking skills?
___Simple
___Advanced
___Intermediate
___Master Craftsman
12. What new accessories would you like Grizzly
Industrial to carry?
6. What stationary woodworking tools do you own?
Check all that apply.
___Builders Hardware
___Fasteners
___Hand Tools
___Air Compressor
___Band Saw
___Panel Saw
___Planer
___Wood Components
___Other_________________________________
___Drill Press
___Power Feeder
___Radial Arm Saw
___Shaper
___Jointer
___Lathe
___Drum Sander
___Dust Collector
___Spindle Sander
___Table Saw
13. What other companies do you purchase your tools
and supplies from?
_________________________________________
_________________________________________
_________________________________________
___Mortiser
___Wide Belt Sander
___Horiz.Boring Machine
___Vacuum Veneer Press
14. Do you think your purchase represents good value?
___Other______________________________
___Yes
___No
7. How many of your woodworking machines are
Grizzly? _____________
15. Would you recommend Grizzly to a friend?
___Yes ___No
8. Which benchtop tools do you own? Check all
that apply.
16. Would you allow us to use your name as a refer-
ence for Grizzly customers in your area? Note: We
never use names more than three times.
___1"x42" Belt Sander ___6" - 8" Grinder
___5" - 8" Drill Press ___Mini Lathe
___Yes
___No
___8" Table Saw
___Scroll Saw
___Spindle/Belt Sander ___Mini Jointer
___10"-12"Thickness Planer
___8" - 10" Bandsaw
___Disc/Belt Sander
17.Comments:________________________________
_________________________________________
_________________________________________
_________________________________________
___Other______________________________
-7-
H0602 12V Cordless Vacuum
Send a Grizzly Catalog to a friend:
Name________________________________
Street________________________________
City______________State______Zip_______
FOLD ALONG DOTTED LINE
GRIZZLY INDUSTRIAL, INC.
P.O. BOX 2069
BELLINGHAM, WA 98227-2069
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
|