All refrigerating dual-drawers refrigerator
Models：
DD300RW（White exterior）
DD350RB（Black exterior）
DD400R* （Stainless steel Door）
DD450R* （Wood door plate）
1
SAFETY PRECAUTIONS
Read all of the instructions before using this appliance.
When using this appliance, always exercise basic safety
precautions, including the following:
1) Use this appliance only for its intended purpose as described in this use
and care guide.
2) This refrigerator must be properly installed in accordance with the
installation instructions before it is used. See grounding instructions in
the installation section.
3) Never unplug your refrigerator by pulling on the power cord. Always grasp
the plug firmly and pull straight out from the outlet.
4) Repair or replace immediately, all electric service cords that have
become frayed or otherwise damaged. Do not use a cord that shows
cracks or abrasion damage along its length, the plug or the connector
end.
5) Unplug your refrigerator before cleaning or before making any repairs.
Note: If for any reason this product requires service, we strongly
recommend that a certified technician performs the service.
6) Do not use any electrical device or any sharp instrument in
defrosting your refrigerator.
7) If your old refrigerator is not being used, we recommend that you remove
the doors and leave the shelves in place. This will reduce the possibility
of danger to children.
8) After your refrigerator is in operation, do not touch the cold surfaces in the
refrigerator compartment, particularly when hands are damp or wet. Skin
may adhere to these extremely cold surfaces.
9) Do not refreeze foods, which have been thawed completely. The United
States Department of Agriculture in Home and Garden Bulletin No. 69
reads: “⋯ You may safely refreeze frozen foods that have thawed if
they still contain ice crystals or if they are still cold-below 40˚F”.
“⋯ Thawed ground meats, poultry, or fish that have any off-odor or
off-color should not be refrozen and should not be eaten. Thawed ice
cream should be discarded. If the odor or color of any food is poor or
questionable, discard it. The food may be dangerous to eat.”
“⋯ Even partial thawing and re-freezing reduce the eating quality of
foods, particularly fruits, vegetables, and prepared foods. The eating
quality of red meats is affected less than that of many other foods. Use
refrozen foods as soon as possible, to save as much of its eating quality
as you can.”
10) This refrigerator should be recessed or built-in an enclosed cabinet. It is not
designed for freestanding installation only.
11) Do not operate your refrigerator in the presence of explosive fumes.
3
SAVE THESE INSTRUCTIONS
For Future Use
DANGER
Risk of child entrapment. Before you throw away your old
refrigerator or refrigerator, take off the door. Leave the shelves in
place so that children may not easily climb inside.
Thank you for using our Haier
product. This easy-to-use manual
will guide you in getting the best
use of your refrigerator.
Remember to record the model and
serial number. They are on a label
in back of the refrigerator.
Model number
Serial number
Date of purchase
Staple your receipt to your manual. You will need it to obtain warranty
service.
TABLE OF CONTENTS
4
Structural drawing
Dimensions drawing
5
Installing instruction
This refrigerator is a kind of build-in product, before you use it
this product must be installed.
Preparation before installing:
First,clean product’s surface with soft cloth,remove all protective coating and belt covering the
product.Don’t use abrasive cleaning cleaners.
1.Pull the upper drawer open,Refer to the illustrations below,put both dividers of shelf on
same side,lift the crisper up off the upper drawer.
2. Lift up both sides of the shelf off the bin cradle with two hands together.
3. Rotate the shelf of upper drawer
6
4.Take the upper shelf out of the upper compartment
Note: After these four steps finished ,please close the upper drawer to avoid damage to your
body by sliding out of drawers of following installation.
Installation:
This refrigerator is a kind of build-in product, before you use it
this product must be installed.
First step:Take off
part“1” (holes cover) of Structural drawing with upwards
strength ,refer to illustrations below:
7
Sencond step:
Take the anti-tip bracket and screws from the accessory bag. Tighten the anti-tip
bracket on the top of the product with screws as following the illustration
Note:Please install just as following illustrations about holes,If you choose wrong hole,it will
do damage to the top of your product and screws.Besides,you should adjust the position of
bracket base on the height of unit in advance，so that we could save operation of taking out
the unit of counter again to choose position of bracket in next step.
Anti-tip Bracket
Screw
Third step: Put the unit inside of counter.Pull upper drawer open and attach the anti-tip
bracket to counter by screw. You can adjust the feet on the corners of unit (Part 7 in Structural
drawing)
8
Removable interior parts:
Crisper
One cripser with cover in upper drawer,user can adjust the position of crisper depending
on needs of storage.
Purpose: Convenient for separate storage of fresh vegetable or fruits.It can stop from
Risk of Odour. You can take crisper out when not needed.
Adjustable shelf.
There are an adjustable shelf in each drawer.User can adjust them to be suitable for
different food storage . You can take it out when not needed.
Note: Keep it in safe place if taken out,especially keep it from children to avoid damage to
them and itself.
○ Adjust of shelf of upper compartment
Separate the compartment to left and right or vice versa.
Rotate the shelf from
the right side to the left
side or vice versa
The rotation operation
finished
Separate the compartment to front and back or vice versa
9
Push
the
plastic
according to the arrow
and move along the
direction of the steel bar
Move the shelf from A to
B
The upper compartment is seperated to left and right parts by middle shelf fastened to bin
cradle of upper compartment.Those two dividers of shelf can be adjusted left and
right,also back and front.For left and right adjust:you can rotate directly. For back and
front: you should push the “push” button in middle connector and move it back to front . If
you want to clean your refrigerator,you can remove the shelf following step of
“Preparation before installing”
Purpose:People can separate the upper compartment with divider according to personal
needs,can keep foods fixed to avoid falling down when drawers and being opend and
closed.
○ Adjust the shelf of lower compartment,referring to illustrations:
10
The shelf of lower compartment is fixed between the embossments of front and back wall
of drawer.You can choose different embossments to divede into different spaces in
drawer.
Purpose: People can separate the lower compartment with divider according to personal
needs,
Dimensions of drawers
Upper drawer
It can load the 2 litter bottle with height of 12 inch,so it can stock all foods or beverage
whose height is less than 12 inch.
Lower drawer
Lower drawer is seperated by step.Foods or beverage whose height is less than 12 inch can
be kept in the space without step.Pop cans can be kept in space with step.
How to use this product
Important notes before connect the power supply:
CAUTION: DON'T USE EXTENSION CORDS.
Actual power supply should keep in accord with marks in rating
plate(115V/60HZ).Rating plate is on back of unit.
Power socket should equiped with fuse of 10A.Keep the refrigerator still for half or one
hour before connnecting to power socket which has been grounded.
Connect the power supply:
Unit is inspected and set to be 38℉ before leaving the factory.When connected with the
power supply,Unit will work normally.
11
Interior LED bulb:
LED bulb is located on top of interior liner in each upper and lower compartment.It is
controlled by approaching switch: when drawer is open,it’s on,when drawer is close,it’s off.
Caution: there are magnet who fix the approaching switch on left side of interior upper
drawer and bottom of lower drawer door.Don’t remove them when unit are working normally.
Temperature setting:
If you wan to change temperature,press “SET” for three seconds,temperature figure will flash
in control panel,then you can adjust the figure and press “SET” to confirm after you complete
your operation.
If you want to reduce the temperature,press the button of ∨
If you want to raise the temperature,press the button of ∧
For example:if you want get 450F, just press “SET” button momently,when “tick”,the figure of
temperature will flash,now you can adjust the temperature,after adjustment,press “SET” to
confirm,then the figure of temperature will flash again.After 5 seconds,it will display the actual
temperature of unit. Then the figure of temperature will keep changing until reach adjusted
temperature,and the display panel will show the changing temperature also.
Temperature range is : 34～47 （1～7℃）.
℉
Thermoregulation guard
Design of thermoregulation guard lock is to avoid children’s changing unconsciously.
Thermoregulation guard unlock: press and hold “SET” for 3 seconds.when “tick”,it means
unlock signal,the temperature figure flashes,you can adjust now.After adjustment,press “SET”
to confirm and start thermoregulation guard clock. Now you can’t adjust the temperature by
pressing “∧”“∨”.
Degree Centigrade and Fahrenheit conversion:
Press and hold“select”for 3 seconds, temperature display will change from Fahrenheit to be
12
Centigrade degree,buzzer will ring once. Press and hold “select” for 3 seconds,it will change
form Centigrade to be Fahrenheit, buzzer will ring once again.
Power switch
Display panel has power button”Power”,If you want to stop unit working for short time or to
restart,press and hold“power” for 3 seconds to open and close.
Notes:If you want to stop unit working for long time,please shut off power supply,take off plug
of socket, cut off the fuser,clean RF,and remove door of unit to get rid of Odour
Sabbath mode
Note: This mode is available for the observance of certain religious holidays.
Press and hold ∧” and “∨” at the same time for 3 seconds, buzzer will ring once,
display panel will flash for 3 times and close.This indicates that the unit has entered Sabbath
mode.In this mode,normal cooling operations still take place(compressor,magnetic
valve,fan,heater strip),but all luminous equipment including display panel,LED bulb will shut
off no matter door is opening or closing.
Press and hold ∧” and “∨” at the same time for 3 seconds,after figure of display panels
flashs for 3 times,you can exit from Sabbath mode.
Sound alarm system
Sound alarm system can keep temperature from exceeding so much
If the door of unit is kept open for long time and affect temperature so much,the system will
give an alarm,if you want to close it,press “SET” button.
When interior temperature of
unit is too hot or cold,product will give an
alarm.Temperature display will change and flash.It will keep flashing until the cause is
removed.If you want to close alarm system,press “SET”button.
Notes: When display error appears,alarm system will take effect,you can shut off the
power supply for 10 minutes if not aware of cause. Restart it again.If problems remain,please
contact with nearest customer sevice center.
Auto Defrost
Unit can defrost automatically: the water of back wall will drain into water tank and be
evaporated by the calorie of condensator.Please check if water can drain into the tank
automatically.
13
Cleaning:
Before cleaning,shut off the power of unit.Take off the plug of socket and remove fuser.
Clean interior surfaces and accessories and outer frame with cold water and a little baking
soda.
Don’t clean with steam to avoid damage to product.
Don’t use abrasive , acidic and chemistical cleanser,Recommend to use neutre cleanser
Keep cleanser from immerging into elcetrical device.
Clean and dry all accessories.
Clean drain hole which is between comparments of unit with small and
soft cleaner such as cotton swab.
TroubleShooting
Refrigerator does not operate:
z
z
Check if refrigerator is plugged in.
Check if there is power in the AC outlet,by checking the circuit breaker.
Refrigerator too warm:
z
z
z
z
z
Frequent door openings.
Allow time for recently added beverage to reach desired temperature.
Check gakets for proper seal.
Clean condenser coils.
Adjust temperature control to colder setting.
Refrigerator runs too frequently:
z
z
This may be normal to maintain constant temperature during high temperature and
humid days.
Doors may have been opened frenquently or for an extended period of time.
14
z
z
z
Clean condenser coils.
Check gasket for proper seal.
Check to see if doors are completely closed.
Moisture build up on interior or exterior of the refrigerator:
z
z
z
This is normal during high humidity periods.
Prolong or frequent door openings.
Check door gaskets for proper seal.
Refrigerator door does not shut properly:
z
z
Level the refrigerator.
Check for blockages e.g. beverage bottles,slide orbit,signal wire under the upper drawer
and the switch under the door plate of the lower drawer.
appliance for a period of 12months. This
Limited Warranty
includes all parts except finish ,and trim.
The components of the sealed system e.g.
hermetic compressor,condenser and
evaporator from manuafacturing defects for
a period of 5 years from the date of
purchase.
What is covered and for how long?
This warranty covers all defects in
workmanship or materials for a period of :
12 months labor
Any damages to such components caused
by mechanical abuse or improper handling
or shipping will not be covered.
12 months parts
5 years sealed system
The warranty commences on the date the
item was purchased and the original
purchase receipt must be presented to the
authorized service center before warranty
repairs are rendered.
What will be done?
We will repair or replace,at our discretion
any mechanical or electrical part which
proves to be defective in normal usage
during the warranty period so specified.
There will be no charge to the purchaser for
parts and labor on any covered items during
the initial 12 month period.Beyond this
period only parts are covered in the
EXCEPTIONS:Commercial or Rental Use
warranty
90 days labor(carry-in only)
90 days parts
No other warranty applies
remaining warranty. Labor is not provided
and must be paid by the customer.
What is covered.
Contact your nearest authorized service
center. For the name of the nearest serive
center please call 1-877-337-3639
The mechanical and electrical parts,which
serve as a functional ,purpose of this
15
THIS WARRANTY COVERS APPLIANCES
WITHIN THE CONTINENTAL UNITED
STATES, PUERTO RICO AND CANADA.
IT DOES NOT COVER THE FOLLOWING:
Damages from improper installion.
Damages in shipping.
PURPOSE
The remedy provided in this warranty is
exclusive and is granted in lieu of all other
remedies.
This warranty does not cover incidental or
consequential damages, so the above
limitations may not apply to you. Some
States do not allow limitations on how long
an implied warranty lasts, so the above
limitations may not apply to you.
This warranty gives you specific legal rights,
and you may have other rights, which vary,
from state to state.
Defects other than manufacturing.
Damage from misuse, abuse, accident,
maintenance or incorrect current or voltage.
Damage from other than household use.
Damage from service by other than an
authorized dealer or service center.
Decorative trims or replaceable light bulbs.
Transprotation and shipping.
Haier America
Labor(after the initial 12 months).
THIS LIMITED WARRANTY IS GIVEN IN
LIEU OF ALL OTHER WARRANTIES,
EXPRESSED OR, INCLUDING THE
WARRANTY OF MERCHANTABILITY
AND FINESS FOR A PARTICULAR
New York, NY 10018
IMPORTANT
Do Not Return This Product To The Store
If you have a problem with this product, please contact the “Haier Customer
Satisfaction Center”at 1-877-337-3639.
DATED PROOF OF PURCHASE REQUIRED ROR WARRANTY SERVICE
16
Made in China
Haier America
New York,NY 10018
Printed in China
17
|