Haier Washer AWT 80LI User Manual

Trouble-shooting  
SEMI AUTO WASHING MACHINE  
AWT-80LI  
If the laundries fall to the outer side of the spin tub  
If the laundries fall to the outer side of the spin tub,  
Please contact the after-sales service department.  
(If there's breakdown, please pull off the power plug before checking) The following  
phenomena are not breakdowns sometimes. Please confirm again before sending  
it to repair. If there are real breakdowns, please come to the special maintenance  
department or after-sale service department of our company. Do not repair it by yourself.  
How to settle  
The reason  
Phenomena  
Manual  
Is there power failure?  
Is the power plug loose?  
Is the pulsator twisted by  
foreign materials?  
Use it when the power is on.  
Insert the power plug tightly.  
Remove the foreign materials?  
USER  
WASHING MACHINE  
The machine does  
not function.  
CONTENTS  
Has the drain hose being  
laid down?  
Put down the drain hose?  
Remove the foreign material?  
The draining does  
not function  
Is the drain hose blocked  
by foreign material?  
Are there any laundries  
trapped at the outer side  
of the spin tub?  
Packing list  
Specification  
Please contact the after-sales  
service department.  
Names of the parts  
Safety precautions  
Installation and adjustment  
Preparation before washing  
Do s and don ts  
Are there hair pin, coins  
or meta items brought  
inside the tub?  
Remove the hair pin, coins or  
metal items  
There's abnormal  
sound during  
washing  
Usage of the detergent  
Washing sequence  
Maintenance  
Pressed the gland evenly  
Is the machine slanting?  
Is the gland pressed evenly?  
Are there any laundries trapped  
at the outer side of the spin tub?  
Are the laundries in spin tub over  
loaded?  
There's abnormal  
sound and violent  
vibration during  
spinning  
Level the machine properly.  
Remove the laundries  
Remove a little laundries  
Trouble-Shooting  
14  
 
Maintenance  
Names of the parts  
After using, please clean the lint and eyewinker of the lint filter and  
overflow filter in time. Otherwise it may influence your using the machine.  
Please first pull off the power plug from the receptacle before cleaning.  
Cleaning the lint filter  
The lint filter must be used during washing.  
It must be cleaned in time after each using.  
1. Take off the lint filter  
Put hand at the indicated position.  
Push down to take it off. ( See  
Figure 1)  
Figure 1  
2. Clean the lint  
Put it in water and clean while it is  
still wet.(See Figure 2)  
3. Install the lint filter  
After cleaning, insert the bottom  
of the lint filter ( marked with  
"down side") into the overflow filter ,  
then push the upper part of the  
filter in ( marked with " up side ").  
(See Figure 3)  
Figure 2  
Meaning and description of the symbols  
Contents marked with that symbol are related  
to the safety of the product and the personal  
safety of the users. Please operate in strict  
conformity to the contents, otherwise it may  
cause damage of the machine or injure the  
personal safety of the user.  
Warning sign  
Figure 3  
Cleaning the overflow filter  
Contents marked with that symbol are actions  
forbidden to perform. Performing of those  
actions may result in damage of the machine  
or injure the personal safety of the user.  
Too much lint on the overflow filter will influence  
the normal usage of the machine. Please  
clean it every two months.  
Forbidding sign  
Elastic fixing  
claw  
Take off the overflow filter.  
As indicated in the figure, nip the elastic fixing  
claw and pull it to the direction of the arrow to  
take it off.  
Please check if the power receptacle has good earthing  
condition before using to guarantee your safety.  
1
12  
 
Safety precautions  
Please insert the power cord into  
When the machine is normally  
using, please put the power plug  
at the location easily to be insert-  
ed and extracted by hand. Be sure  
to pull the plug off when there's  
power failure, or the machine is  
being moved, cleaned or when it  
is idle.  
special receptacle with rated vol-  
tage.Be sure to use single-phase  
three pins receptacle.The earthing  
terminal of the receptacle must be  
earthed reliably.If possible,please  
adopt electric leakage protector.  
Spinning  
1.Put the laundries into the spin tub evenly and smoothly.  
Earth  
2.Press the gland in the tub properly. Close the inner and  
outer cover of the spin tub.  
If the supply cord is damaged,it must be replaced  
by the manufacturer or its service  
agent or a similarly qualified person  
in order to avoid a hazard.  
3.Spin  
Select suitable spin time according to the laundries, and do spinning.  
Do not use water hotter than 50 C .  
Do not put the machine at damp  
place like the bathroom . Never  
wash it with water. Do not place  
wet laundries on the control panel.  
During spinning, if there is abnormal sound, it is generally owing to  
slanting placement of the laundries. Please stop the machine and  
reorder the laundries.  
In spinning, it will pause the work if you open the outer cover of the  
spin tub. Close it to resume the spinning.  
For washing machine with ventilation  
openings in the base, that a carpet  
must not obstruct the openings.  
Do not wash water-proof laundries like  
the raincoat, bike covers etc. to avoid  
abnormal vibrations.  
To do spinning and draining and rinse  
with water-filling together, please first  
do spinning for around 1 minute, then  
do draining or rinse with water-filling .  
Otherwise the spinning will stop owing  
to too much water stored in the spin tub.  
Ventilation hole at  
the bottom of the  
washing machine  
Do not let the machine share one receptacle  
with other electric appliances. If the power  
plug is damaged, or the plugging into the  
receptacle is loose, do not use the plug any  
more.  
2
11  
 
Safety precautions  
Do not stretch hands into the working  
Do not decompose, repair or alter the  
machine by yourself.  
Rinsing  
machine. It is dangerous even if the  
rotation is slow. Take special care of  
the children.  
Rinse with water-filling  
1.Put the laundries  
Put the laundries into the wash tub. Select suitable current according  
to the laundries.  
2.Adjust the water level  
Set the water level with water level adjusting lever according to the  
laundries quantity. Then fill suitable water continuously.  
Do not put any hot or heavy items  
( such as the kettle with hot water )  
on the washing machine.  
Do not wash laundries with volatile  
materials (such as thinner, petrol etc.).  
3.Rinse  
Adjust the wash timer to 5-7 minutes to do rinsing.  
l
ro  
et  
er  
inn  
Th  
P
Rinse with stored water  
(Repeat the midway spinning and rinsing with stored water  
for 2-3 times)  
Keep the machine away from direct  
sunlight and heat source like the  
heater.  
Handicapped or children without care  
shall not use the machine.  
1. Put the laundries into the wash tub. Select suitable current according to  
the laundries.  
2. Fill water to preset water level.  
3. Rinse  
Adjust the wash timer to 2-3 minutes to do rinsing.  
When the laundries quantity is few, please use "Standard" current.  
If you use "Strong" current, it may splash.  
To protect your laundries and wash-  
ing machine, please take out all of the  
coins, buttons, sand, hairpin and  
other foreign materials before washing.  
Please check if the connection of the  
water inlet pipe is proper.  
It is suggested to use foamless washing  
powder.  
3
10  
 
Installation and adjustment  
Please install and adjust the machine according to the requirement of  
the manual. It is very important to your security and correct operating  
the machine.  
Midway spinning  
Install the lint filter  
1.Put the laundries into the spin tub evenly and smoothly.  
2.Spin  
(1) Put the gland in properly.  
After opening the package,please take out the lint  
filter from the document bag,install it to the overflow  
filter of the wash tub.See to the figure.  
Overflow filter  
Please put in the gland properly even if the laundries quantity is small.  
Push  
Gland  
Lint filter  
Push  
Usage of the drain hose  
Proper  
Proper  
The laundries  
are slanting  
The drainage shall be smooth with the drain hose.  
No gland  
1.The height of the drain hose shall be  
less than 10cm , or the drainage will  
not be smooth enough and cause  
(2) Close the inner and outer cover of the spin tub.  
<10cm  
(3) Spin for 1-2 minutes.  
Outer cover of  
the spin tub  
incomplete drainage.  
2.Do not tramp or press the drain hose.  
Inner cover of  
the spin tub  
3.If the drain hose is too long, cut it at mid point.  
To make smooth drainage, cut the front end of  
the hose slantingly.  
3.Run the foam-removing spinning.  
1
Set the inlet selector handle on spin side and  
Water inlet  
Inlet selector handle  
fill water for about 1 min.  
4.If extra drain hose is needed , please make  
separate purchase. The inner diameter of the  
extra hose shall not less than 30mm, and the  
In case water flows out from wash tub side  
due to too much inflow, please turn down  
the water tap a bit.  
Spin  
Wash  
>
30mm  
length shall not exceed 1.5m.  
<1.5m  
2
Close the spin tub outer cover and spin  
for about 1 - 2 min.  
If the extra hose is too long, cut it either  
at point A or B.  
A
B
4
9
 
How to change the direction of the drain hoses  
Washing sequence  
Wash selector  
Spin timer  
Wash timer  
(To set to below 2 minute,  
Figure 1 indicates the ex factory installation  
position of the drain hose.  
(Strong current,  
standard current)  
(to set to below 1 minute,  
first set to 2 minute then  
turn it back. it can increase  
the service life of the timer).  
Side sectional view  
first set to  
5
minute then  
turn it back. it can increase  
the service life of the timer).  
Drain hose  
Fixing hook  
fixing hook  
installation hole  
STRONG  
OFF  
Extend the drain hose from the side of spin tub.  
OFF  
Drain hose  
Pull outwards  
slightly  
STANDARD  
3
1
2
15  
5
Take off the drainhose from the hanging  
hole of the cabinet. Pull the drain hose  
fixing hook outwards gently to take out  
the drain hose from the twofixing hooks.  
(As per Figure 2)  
DRAIN  
Take off  
the drain hose  
12  
6
4
WASH SEELECTOR  
SPIN TIMER  
WASH TTIMER  
3
Drain hose  
fixing hook  
9
Figure 1  
Figure 2  
Rotate the drainhose fixing hook for 90  
to take it out from the installation hole  
(As per Figure 3).  
Wash  
Install the two drain hose fixing hooks taken  
out into the installation hole at the other side of  
the base frame (to aim at the installation hole  
accurately you can lean the washing machine  
forward slightly).Then rotatefor 90 (As per Figure 4).  
Rotate the fixing  
hook for 90  
Rotate the fixing  
hook for 90  
to fix it  
1
Inlet selector  
Take off the fixing  
hook downwards  
Insert the fixing hook into the  
installation hole upwards  
WASH  
SPIN  
(1) Set inlet selector to Wash side. Figure 1  
(2 )Adjust water level rod to a position as needed.  
Figure 1  
Pull the fixing hook outwards slightly. Inlay the drain  
hose into the fixing hooks reliably along the groove  
at spin tub side, and make it extend towards spin  
tub side..  
Then hang thedrain hose into the hanging hole at  
the spin tub side. (As per Figure 5).  
Figure 4  
Figure 3  
2. Fill the water and add the dissolved washing  
powder to make the water level reach the preset  
position. (Figure 2)  
Run washing program for some time to stir and  
dissolve the powder completely.  
Figure 2  
Figure 3  
Extend the drain hose from the back side  
STRONG  
STANDARD  
Take out the drain hose from the two fixing hooks.  
make it extend towards back side.(Extend the drain  
hose from the side of back, hang the drain hose in  
to the hanging hole at the both sides) . (As per Figure 6).  
Figure 5  
Figure 6  
DRAIN  
3.Put in the laundries. If the water quantity is  
insufficient, please add water.  
Install the water inlet hose; Select the water level  
4.Select the current.  
Select the strength of the current according to  
the laundries. (Figure 3)  
OFF  
3
6
15  
12  
Water inlet hose  
Insert the water inlet hose into the water-filling  
entrance on the control panel directly.(pull it  
out to dismantle it)  
5.Select the washing time  
Select the washing time according to the  
laundries. (Figure 4)  
Figure 4  
9
Select water level according to the  
quantity of the laundries.  
Water level  
indicator  
STRONG  
6.After washing,the buzzer will ring .Set  
the "WASH SELECTOR" at "DRAIN".  
(Figure 5).  
Set the water level adjusting lever  
to needed line.  
STANDARD  
Max.  
Med  
Min  
Maximum  
DRAIN  
Use the new water inlet hose provided  
with the machine to connect to the  
water faucet.Old hose sets should  
not be reused.  
Medium  
Figure 5  
Minimum  
5
8
 
Preparation before washing  
Do s and Don ts  
The capacity of washing and spinning of the  
Preparation before washing  
1.Connect the water inlet hose.  
machine refer to the weight of the  
standard laundries under dry condition that can  
be washed or spinned in one time.  
the largest capacity is only the loading capacity  
of the drum  
The thickness ,size , type of the cloth will influ-  
ence the actual washing capacity. It is suit-  
able to put in reasonable amount of laundries  
and the laundries can be turned round in wash-  
ing for one time washing.  
2.Confirm that the washing machine is earthed  
reliably . Then insert the power plug into the  
receptacle. Do not connect the earth terminal  
to the gas pipe and tap water pipe.  
3.Put down the drain hose .  
Do not select " Maximum " water level for  
laundries less than 1.5kg, so as to avoid  
splashing of water.  
4.Slanting or uneven ground may result in  
unstable working or abnormal noise. Please  
make the machine stand horizontally.  
It is suggested not to use high sudsing detergent.  
Usage of the detergent  
Pay attention to following before washing the laundries  
Check if  
The quantity of  
When the pulsator  
How to use the whitener  
How to use the washing powder  
Clear the  
Tie the long  
strips; fasten  
the buttons;  
close zippers.  
the laundries  
has special  
requirement  
on washing  
the laundries is running , the  
shall not be too buttons of the  
large. Stretch laundries may  
and loosen the cause noise. For  
laundries before the sake of  
pocket. Take  
out the coins,  
sand, hairpins  
etc.  
Direct dissolved in the machine:  
1.Fill small quantity of water.  
2.Add the powder . Run for 30  
seconds to dissolve it completely.  
3.Put in laundries. Select suitable  
water level.  
Fill water to decided level. Dilute  
the whitener with container.  
Pour it slowly into the washing tub.  
putting them in discretion, please  
the tub.  
put the laundries  
with buttons into  
other laundries.  
Avoid using whitener on laun-  
dries with color or pattern as they  
are prone to lose color.  
The instant dissolving of the washing  
powder:  
1.Prepare warm water of 30 C and a  
container.  
2.Add the powder while stirring to fully  
dissolve it.  
The powder is more prone to pollute the  
laundries than the detergent. Therefore  
please use it with proper quantity.  
The whitener shall not touch  
the laundries directly.  
Refer to the user's manual for  
the usage and quantity of the  
whitener.  
a. Check if the laundries are applicable for washing with machine.  
b. Divide the laundries that are not colorfast from other laundries.  
c. Put those laundries difficult to absorb water into water with hand.  
d. For those laundries with heavy soil, please first remove the dirt like  
mud or dust. For the parts with heavy soil, please apply detergent on  
them in advance, which can make it easier to remove the soil.  
e. For those laundries that may get lint ball and those with long fur, turn  
it over before putting in.  
For powder whitener, please  
dissolve it before using.  
Dosage of different washing powder is  
different. Please refer to the instruction  
of the washing powder for the detail  
dosage.  
f. Do not put those laundries polluted by chemicals into the washing  
machine directly.  
6
7
 

Grace CD Player GDI C2CDRW User Manual
Graco Baby Carrier ISPC094CB User Manual
Graco Baby Furniture PD246920A User Manual
Harbor Freight Tools Biscuit Joiner 68114 User Manual
Havis Shields Automobile Parts C TTB CHGR User Manual
Healthrider Treadmill HRTL16991 User Manual
HSM Paper Shredder HSM FA 5002 User Manual
Husqvarna Chainsaw 2083 II User Manual
ICP DAS USA Network Card I 7531 User Manual
iHome Portable Stereo System IP97 User Manual