®
MINI AIR COMPRESSOR
250 PSI
Model 04077
ASSEMBLY and OPERATING
INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Copyright c 2003 by Harbor Freight Tools® . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
9. Maintain tools with care. Keep tools clean for better and safer performance. Follow
instructions for lubricating and changing accessories. Inspect tool cords and air hoses
periodically and, if damaged, have them repaired by an authorized technician. The
handles must be kept clean, dry, and free from oil and grease at all times.
10. Disconnect Compressor. Disconnect cigarette lighter plug in when not in use.
11. Avoid unintentional starting. Be sure the thumbwheel switch is in the Off position
when not in use and before plugging in.
12. Stay alert. Watch what you are doing, use common sense. Do not operate any tool
when you are tired.
13. Check for damaged parts. Before using any tool, any part that appears damaged
should be carefully checked to determine that it will operate properly and perform its
intended function. Check for alignment and binding of moving parts; any broken parts
or mounting fixtures; and any other condition that may affect proper operation. Any
part that is damaged should be properly repaired or replaced by a qualified
technician. Do not use the tool if any switch does not turn On and Off properly.
14. Guard against electric shock. Prevent body contact with grounded surfaces such as
pipes, radiators, ranges, and refrigerator enclosures.
14. Replacement parts and accessories. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty. Only use accessories
intended for use with this tool. Approved accessories are available from Harbor
Freight Tools.
16. Do not operate tool is under the influence of alcohol or drugs. Read warning
labels if taking prescription medicine to determine if your judgement or reflexes are
impaired while taking drugs. If there is any doubt, do not operate the Compressor.
17. Maintenance. For your safety, maintenance should be performed regularly by a
qualified technician.
Note: Performance of the compressor (if powered by line voltage) may vary depending
on variations in local line voltage.
Warning:The warnings, cautions, and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. It must be under-
stood by the operator that common sense and caution are factors which cannot be
built into this product, but must be supplied by the operator.
Unpacking
When unpacking, check to make sure the parts listed on page 5 are included. If any parts
are missing or broken, please call Harbor Freight Tools at the number on the cover of this
manual as soon as possible.
Page 3
SKU 04077
Operation
1. Remove the Power Cord/Cigarette Plug (#11) from the recessed holder on the unit.
See FIGURE 1.
FIGURE 1
EXPLOSION DANGER
Before inflating tires or toys
check the manufacturer’s
recommended air pres-
sure. Do not exceed that
pressure. Over inflation
may result in an explosion.
Cord/Cigarette Plug (#11)
Holder
2. Check to make sure the Thumbwheel Switch on the power cord is in the “off” position.
3. Situate the Compressor outside of the car.
3. Plug the Cord/Cigarette Plug (#11) into the 12 Volt receptacle (or cigarette lighter) in the
car. If you run your car to charge the battery while using this Compressor, never run the car
in an enclosure of any kind. Your car emits Carbon Monoxide, an odorless, colorless gas,
which is extremely lethal.
Note: When attaching the Air Outlet (#6) to a tire or adapter, lift the Valve Lock (see
Assembly Drawing on page 6. Then attach the hose to the tire or adapter, and then lock down
the Valve Lock. To remove it from the tire or adapter, lift the Valve Lock and remove.
4. If you are going to fill a standard tire, then no adapter is needed as the Air Outlet (#6) end
has a universal tire adapter.
5. To fill a standard athletic ball, thread on the Sports Needle accessory.
6. When using the unit as an air blower, thread on the appropriate sized adapter
(two included). See FIGURE 2
Warning! Make sure that no one is touching the Compressor when it is in operation. The
Compressor will become very hot; avoid being burned.
7. Attach the Compressor to the item you wish you inflate as explained in the Note above.
8. Turn on the Compressor by sliding the Thumbwheel to the “on” position.
Warning!: Do not allow the Compressor to run for more than 15 minutes at a time. After 15
minutes, allow it to cool for 5 minutes, and then you may resume inflation. Failure to do so
may cause the unit to overheat and burn out.
9. When you are finished, turn off the Compressor by sliding the Thumbwheel to the “off”
position. Lift up on the Valve Lock and unplug the unit. Store the Cord/Cigarette Plug (#11)
in the recessed holder in the unit.
FIGURE 2
Ball Needle
Air Adapters
Page 4
SKU 04077
Parts List
Part No.
Description
1
Hull
2
Cylinder Head
3
Gauge
4
Plug
5
Rubber Hose
6
Air Outlet
7
Seal
8
Motor
9
Shaft
10
11
Gasket
Power Cord/Cigarette Plug
Maintenance
1. Visually inspect the unit before each use to make sure the hoses are properly attached and
the hoses and the power cord are not frayed or torn.
2. Check that the cigarette plug is clean of dirt, grease, or debris.
3. Make sure the universal outlet adapter is clean of dirt, grease, or debris.
PLEASE READTHE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDEDTHE PARTS DIAGRAM INTHIS
MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBU-
TOR MAKES ANY REPRESENTATION ORWARRANTY OF ANY KINDTO THE BUYERTHAT HE
OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER
AND/OR DISTRIBUTOR EXPRESSLY STATESTHAT ALL REPAIRS AND PARTS REPLACEMENTS
SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE
BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER
REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING
OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
NOTE: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.
Page 5
SKU 04077
Assembly Drawing
Valve Lock
Page 6
SKU 04077
|