1
Heavy-duty / ” vSR dRill
2
Model 3273
Set up and OpeRating inStRuctiOnS
Read this material before using this product.
Failure to do so can result in serious injury.
Save tHiS Manual.
©
®
Copyright 2003 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Manual revised 10f
not avoided, could result in
minor or moderate injury.
Save tHiS Manual
Keep this manual for the safety
warnings and precautions, assembly,
operating, inspection, maintenance and
cleaning procedures. Write the product’s
serial number in the back of the manual
near the assembly diagram (or month
and year of purchase if product has no
number). Keep this manual and the
receipt in a safe and dry place for future
reference.
nOtice is used to
address practices
not related to personal injury.
cautiOn, without
the safety alert
symbol, is used to address
practices not related to
personal injury.
general power tool Safety
warnings
iMpORtant SaFety
inFORMatiOn
in this manual, on the labeling,
and all other information
waRning Read all safety
warnings and instructions.
Failure to follow the warnings and
instructions may result in electric
shock, fire and/or serious injury.
Save all warnings and
instructions for future reference.
The term ″power tool″ in the
warnings refers to your mains-
operated (corded) power tool or
battery-operated (cordless) power
tool.
provided with this product:
this is the safety alert
symbol. it is used to alert
you to potential personal
injury hazards. Obey all
safety messages that
follow this symbol to avoid
possible injury or death.
1. work area safety
dangeR indicates
a hazardous
situation which, if not
avoided, will result in death or
serious injury.
a. keep work area clean and well
lit. Cluttered or dark areas invite
accidents.
b. do not operate power tools in
explosive atmospheres, such
as in the presence of flammable
liquids, gases or dust. Power tools
create sparks which may ignite the
dust or fumes.
waRning
indicates a
hazardous situation which, if
not avoided, could result in
death or serious injury.
c. keep children and bystanders
away while operating a power
tool. Distractions can cause you to
lose control.
cautiOn, used
with the safety
alert symbol, indicates a
hazardous situation which, if
SKU 3273
For technical questions, please call 1-800-444-3353.
Page 3
2. electrical safety
A moment of inattention while
operating power tools may result in
serious personal injury.
a. power tool plugs must match the
outlet. never modify the plug in
any way. do not use any adapter
plugs with grounded power tools.
Unmodified plugs and matching
outlets will reduce risk of electric
shock.
b. use personal protective
equipment. always wear eye
protection. Safety equipment such
as dust mask, non-skid safety shoes,
hard hat, or hearing protection used
for appropriate conditions will reduce
personal injuries.
b. avoid body contact with grounded
surfaces such as pipes, radiators,
ranges and refrigerators. There is
an increased risk of electric shock if
your body is grounded.
c. prevent unintentional starting.
ensure the switch is in the off-
position before connecting to
power source and/or battery pack,
picking up or carrying the tool.
Carrying power tools with your finger
on the switch or energizing power
tools that have the switch on invites
accidents.
c. do not expose power tools to rain
or wet conditions. Water entering
a power tool will increase the risk of
electric shock.
d. do not abuse the cord. never use
the cord for carrying, pulling or
unplugging the power tool. keep
cord away from heat, oil, sharp
edges or moving parts. Damaged
or entangled cords increase the risk
of electric shock.
d. Remove any adjusting key or
wrench before turning the power
tool on. A wrench or a key left
attached to a rotating part of the
power tool may result in personal
injury.
e. when operating a power tool
outdoors, use an extension cord
suitable for outdoor use. Use
of a cord suitable for outdoor use
reduces the risk of electric shock.
e. do not overreach. keep proper
footing and balance at all times.
This enables better control of the
power tool in unexpected situations.
f. dress properly. do not wear
loose clothing or jewelry. keep
your hair, clothing and gloves
away from moving parts. Loose
clothes, jewelry or long hair can be
caught in moving parts.
f. if operating a power tool in a
damp location is unavoidable, use
a ground Fault circuit interrupter
(gFci) protected supply. Use of
a GFCI reduces the risk of electric
shock.
g. if devices are provided for the
connection of dust extraction and
collection facilities, ensure these
are connected and properly used.
Use of these devices can reduce
dust-related hazards.
3. personal safety
a. Stay alert, watch what you are
doing and use common sense
when operating a power tool. do
not use a power tool while you
are tired or under the influence
of drugs, alcohol or medication.
h. Only use safety equipment
that has been approved by an
SKU 3273
For technical questions, please call 1-800-444-3353.
Page 4
appropriate standards agency.
Unapproved safety equipment may
not provide adequate protection.
Eye protection must be ANSI-
approved and breathing protection
must be NIOSH-approved for the
specific hazards in the work area.
f. keep cutting tools sharp and
clean. Properly maintained cutting
tools with sharp cutting edges are
less likely to bind and are easier to
control.
g. use the power tool, accessories
and tool bits etc. in accordance
with these instructions, taking
into account the working
4. power tool use and care
a. do not force the power tool. use
the correct power tool for your
application. The correct power tool
will do the job better and safer at the
rate for which it was designed.
conditions and the work to be
performed. Use of the power tool
for operations different from those
intended could result in a hazardous
situation.
b. do not use the power tool if the
switch does not turn it on and
off. Any power tool that cannot
be controlled with the switch is
dangerous and must be repaired.
drill and impact drill Safety
warnings
1. wear ear protectors with impact
drills. Exposure to noise can cause
hearing loss.
c. disconnect the plug from the
power source and/or the battery
pack from the power tool before
making any adjustments,
2. use auxiliary handles supplied
with the tool. Loss of control can
cause personal injury.
changing accessories, or storing
power tools. Such preventive
safety measures reduce the risk of
starting the power tool accidentally.
3. Hold power tools by insulated
gripping surfaces when performing
an operation where the cutting tool
may contact hidden wiring or its
own cord. Contact with a ″live″ wire
will make exposed metal parts of the
tool ″live″ and shock the operator.
d. Store idle power tools out of
the reach of children and do not
allow persons unfamiliar with the
power tool or these instructions
to operate the power tool. Power
tools are dangerous in the hands of
untrained users.
4. Maintain labels and nameplates on
the tool. These carry important safety
information. If unreadable or missing,
contact Harbor Freight Tools for a
replacement.
e. Maintain power tools. check
for misalignment or binding of
moving parts, breakage of parts
and any other condition that may
affect the power tool’s operation.
if damaged, have the power
tool repaired before use. Many
accidents are caused by poorly
maintained power tools.
5. Avoid unintentional starting. Prepare
to begin work before turning on the
tool.
6. Do not lay the tool down until it has
come to a complete stop. Moving
SKU 3273
For technical questions, please call 1-800-444-3353.
Page 5
parts can grab the surface and pull
the tool out of your control.
Your risk from these exposures
varies, depending on how often you
do this type of work. To reduce your
exposure to these chemicals: work in
a well ventilated area, and work with
approved safety equipment, such as
those dust masks that are specially
designed to filter out microscopic
particles. (California Health & Safety
Code § 25249.5, et seq.)
7. When using a handheld power tool,
maintain a firm grip on the tool with
both hands to resist starting torque.
8. Do not leave the tool unattended
when it is plugged into an electrical
outlet. Disengage the trigger, and
unplug the tool from its electrical
outlet before leaving.
12. WARNING: Handling the cord on
this product will expose you to lead,
a chemical known to the State of
California to cause cancer, and
birth defects or other reproductive
harm. Wash hands after handling.
(California Health & Safety Code §
25249.5, et seq.)
9. This product is not a toy. Keep it out
of reach of children.
10. People with pacemakers should
consult their physician(s) before
use. Electromagnetic fields in close
proximity to heart pacemaker could
cause pacemaker interference or
pacemaker failure. In addition,
people with pacemakers should:
• Avoid operating alone.
13. The warnings, precautions,
and instructions discussed in
this instruction manual cannot
cover all possible conditions and
situations that may occur. It must
be understood by the operator that
common sense and caution are
factors which cannot be built into this
product, but must be supplied by the
operator.
• Do not use with power switch locked
on.
• Properly maintain and inspect to
avoid electrical shock.
• Any power cord must be properly
grounded. Ground Fault Circuit
Interrupter (GFCI) should also be
implemented – it prevents sustained
electrical shock.
vibration Safety
This tool vibrates during use.
Repeated or long-term exposure to
vibration may cause temporary or
permanent physical injury, particularly
to the hands, arms and shoulders. To
reduce the risk of vibration-related
injury:
11. WARNING: Some dust created by
power sanding, sawing, grinding,
drilling, and other construction
activities, contains chemicals
known [to the State of California] to
cause cancer, birth defects or other
reproductive harm. Some examples
of these chemicals are:
1. Anyone using vibrating tools regularly
or for an extended period should
first be examined by a doctor and
then have regular medical check-
ups to ensure medical problems are
• Lead from lead-based paints
• Crystalline silica from bricks and
cement or other masonry products
• Arsenic and chromium from
chemically treated lumber
SKU 3273
For technical questions, please call 1-800-444-3353.
Page 6
not being caused or worsened from
use. Pregnant women or people
who have impaired blood circulation
to the hand, past hand injuries,
nervous system disorders, diabetes,
or Raynaud’s Disease should not use
this tool. If you feel any symptoms
related to vibration (such as tingling,
numbness, and white or blue fingers),
seek medical advice as soon as
possible.
electrician if you are in doubt
as to whether the outlet is
properly grounded. do not
modify the power cord plug
provided with the tool. never
remove the grounding prong
from the plug. do not use the
tool if the power cord or plug
is damaged. if damaged, have
it repaired by a service facility
before use. if the plug will not
fit the outlet, have a proper
outlet installed by a qualified
electrician.
2. Do not smoke during use. Nicotine
reduces the blood supply to the
hands and fingers, increasing the risk
of vibration-related injury.
double insulated tools: tools
with two prong plugs
3. Wear suitable gloves to reduce the
vibration effects on the user.
4. Use tools with the lowest vibration
when there is a choice.
5. Include vibration-free periods each
day of work.
6. Grip tool as lightly as possible (while
still keeping safe control of it). Let
the tool do the work.
Outlets for 2-prong plug
7. To reduce vibration, maintain the tool
as explained in this manual. If any
abnormal vibration occurs, stop use
immediately.
1. Tools marked “Double Insulated”
do not require grounding. They
have a special double insulation
system which satisfies OSHA
requirements and complies with the
applicable standards of Underwriters
Laboratories, Inc., the Canadian
Standard Association, and the
National Electrical Code. (See
Outlets for 2-prong plug.)
Save tHeSe
inStRuctiOnS.
gROunding
2. Double insulated tools may be used
in either of the 120 volt outlets shown
tO pRevent
electRic SHOck
and deatH FROM
incORRect gROunding
wiRe cOnnectiOn:
Check with a qualified
SKU 3273
For technical questions, please call 1-800-444-3353.
Page 7
in the preceding illustration. (See
Outlets for 2-prong plug.)
extension cord or have it repaired by
a qualified electrician before using it.
8. Protect the extension cords from
sharp objects, excessive heat, and
damp or wet areas.
extension cords
1. Grounded tools require a three wire
extension cord. Double Insulated
tools can use either a two or three
wire extension cord.
RecOMMended MiniMuM wiRe
gauge FOR extenSiOn cORdS*
(120/240 vOlt)
extenSiOn cORd
2. As the distance from the supply
outlet increases, you must use a
heavier gauge extension cord. Using
extension cords with inadequately
sized wire causes a serious drop in
voltage, resulting in loss of power and
possible tool damage.
naMeplate
lengtH
aMpeReS
(at full load)
0 – 2.0
2.1 – 3.4
18
18
18
18
18
14
12
18
18
18
16
14
12
10
18
18
16
14
12
10
-
18
16
14
12
10
-
16
14
12
12
-
3.5 – 5.0
(See table a.)
5.1 – 7.0
7.1 – 12.0
12.1 – 16.0
16.1 – 20.0
3. The smaller the gauge number of the
wire, the greater the capacity of the
cord. For example, a 14 gauge cord
can carry a higher current than a 16
gauge cord. (See table a.)
-
-
-
* based on limiting the line
voltage drop to five volts at
150% of the rated amperes.
table a
4. When using more than one extension
cord to make up the total length,
make sure each cord contains at
least the minimum wire size required.
(See table a.)
Symbology
Double Insulated
5. If you are using one extension cord
for more than one tool, add the
nameplate amperes and use the sum
to determine the required minimum
cord size. (See table a.)
Canadian Standards Association
Underwriters Laboratories, Inc.
Volts Alternating Current
Amperes
v~
a
6. If you are using an extension cord
outdoors, make sure it is marked with
the suffix “W-A” (“W” in Canada) to
indicate it is acceptable for outdoor
use.
No Load Revolutions per Minute
(RPM)
n xxxx/min.
0
7. Make sure the extension cord is
properly wired and in good electrical
condition. Always replace a damaged
SKU 3273
For technical questions, please call 1-800-444-3353.
Page 8
assembly
SpeciFicatiOnS
Thread the auxiliary handle securely
into the left or right side of the drill.
Electrical Input 120 V~ / 60 Hz / 6.3 A (Rated)
Motor Speed
Chuck Capacity 1/2” (13mm)
Approximate 3/4” Wood
Work Capacity 1/2” Metal
0-1200 RPM (No Load)
Functions
chuck
lock
Ring
button
90SM
e194601
bQ
chuck
key Hole
unpacking
chuck
jaws
When unpacking, make sure that the
item is intact and undamaged. If any parts
are missing or broken, please call Harbor
Freight Tools at 1-800-444-3353 as soon
as possible.
auxiliary
Handle
trigger
direction
Switch
key
Holder
inStRuctiOnS FOR
putting intO uSe
OpeRating inStRuctiOnS
Read the entiRe iMpORtant
SaFety inFORMatiOn
section at the beginning of this
manual including all text under
subheadings therein before set
up or use of this product.
Read the entiRe iMpORtant
SaFety inFORMatiOn
section at the beginning of this
manual including all text under
subheadings therein before set
up or use of this product.
tool Set up
tO pRevent
SeRiOuS injuRy
FROM accidental
OpeRatiOn:
disengage the trigger and
unplug the tool from its
electrical outlet before
assembling or making any
adjustments to the tool.
tO pRevent
SeRiOuS injuRy
FROM accidental
OpeRatiOn:
disengage the trigger and
unplug the tool from its
electrical outlet before
adjusting tool or installing
accessories.
note: For additional information regarding
the parts listed in the following pages,
refer to the Assembly Diagram near
the end of this manual.
tO inStall a dRill bit:
1. Insert the Chuck Key into the Chuck
Key Hole and turn it counterclockwise
to open the Chuck Jaws.
Rev10f
SKU 3273
For technical questions, please call 1-800-444-3353.
Page 9
2. Slide the bit into the Jaws as far as it
will go without inserting the drill flutes
into the chuck.
3. Squeeze the Trigger to start the tool.
The Trigger has a variable speed
feature. Moving the Trigger slightly
will make the tool operate slowly,
moving the trigger more will cause
the tool to operate faster.
3. Hold the bit centered in the Jaws
while turning the Chuck Key
clockwise to secure it in place.
4. You can lock the Trigger in the ON
position by squeezing the trigger,
pressing in the Lock Button, and
releasing the Trigger. The tool will
operate continuously. To stop the tool,
squeeze and release the Trigger.
4. Firmly tighten the Jaws using the
Chuck Key.
5. Remove the Chuck Key and store it
in the holder on the power cord.
work piece and work area Set up
5. Use only well-sharpened bits that are
in good condition and appropriate to
the task.
1. Designate a work area that is clean
and well-lit. The work area must not
allow access by children or pets to
prevent distraction and injury.
6. Use firm pressure when drilling,
but do not press too hard. Too
much pressure will cause the bit to
overheat, may cause the bit to bend
or break, cause undue strain on
the tool, and may damage the work
piece. Pressing too hard may stall the
motor.
2. Route the power cord along a safe
route to reach the work area without
creating a tripping hazard or exposing
the power cord to possible damage.
The power cord must reach the work
area with enough extra length to
allow free movement while working.
7. if the motor stalls, release the
trigger immediately to prevent
damage to the tool.
3. Secure loose work pieces using
a vise or clamps (not included) to
prevent movement while working.
8. Only drill in a straight line. Bending
or twisting the bit while drilling may
cause the bit to bend or break and
may damage the work piece.
4. There must not be objects, such as
utility lines, nearby that will present a
hazard while working.
9. Back off your pressure if you are
about to penetrate the other side of
the work piece.
general Operating instructions
1. Make sure the trigger is released
and not locked on, then plug the
Power Cord into a suitable outlet.
10. Keep the motor running when pulling
the bit out of a completed hole to
prevent the bit from jamming.
2. Press the Direction Switch of the
Trigger to determine the rotation
direction. Press to the left side for
clockwise rotation. Press to the right
side for counterclockwise rotation.
SKU 3273
For technical questions, please call 1-800-444-3353.
Page 10
3. Start by drilling slowly to keep the bit
from moving away from your starting
point. Increase speed as the hole is
established.
Metal drilling
1. Use high speed steel, carbide, TiN
coated, or specialty bits for metal
drilling.
4. To prevent or reduce “break out”
when the bit penetrates the work
piece, clamp a piece of scrap material
to the back of the work piece.
2. Secure the work piece to keep it from
moving during the drilling operation.
3. To make starting the hole easier, use
a punch to create a dimple at the hole
center.
5. Do not lock the Trigger in the ON
position, as the bit can easily jam in
wood and the motor must be stopped
quickly.
4. Unless drilling into cast iron or brass
use a cutting lubricant.
after use
5. Start by drilling slowly to keep the bit
from moving away from your starting
point.
To prevent accidents, disengage
the trigger, remove the bit, and
disconnect the tool’s power supply
after use. Clean, then store the tool
indoors out of children’s reach.
6. As the hole is established, increase
tool speed. Do not go so fast or use
so much pressure that the bit heats
up. This can damage the bit and
create an irregular hole. For hard
metal, use cutting oil to keep the bit
cool.
7. Since drilling in metal is a slow
operation, you may lock the Trigger
in the ON position to maintain a
constant speed and reduce fatigue.
8. When drilling large holes in metal,
start by drilling a smaller pilot hole,
then using a larger bit for the final
size hole.
wood drilling
1. Use high speed bits or bits specially
designed for wood drilling, such as
brad point, spade bits, forstner bits,
etc.
2. Secure the work piece to keep it from
moving during the drilling operation.
SKU 3273
For technical questions, please call 1-800-444-3353.
Page 11
carbon brush Service
Maintenance and
SeRvicing
If the Carbon Brushes are damaged
or worn, they must be replaced
by a qualified service technician.
improper service may result in the
double insulation system being
compromised.
Procedures not specifically
explained in this manual
must be performed only by a
qualified technician.
tO pRevent
SeRiOuS injuRy
chuck (1) Replacement
FROM accidental
OpeRatiOn:
1. disengage the trigger and unplug
the tool from its electrical outlet.
disengage the trigger and
unplug the tool from its
electrical outlet before
performing any inspection,
maintenance, or cleaning
procedures.
2. Open the Chuck Jaws fully.
3. Remove the Chuck Screw (44)
inside the Chuck Jaws by turning it
counterclockwise.
4. Switch the Direction Switch to the
reverse direction. Plug the Power
Cord into a suitable outlet.
tO pRevent SeRiOuS
injuRy FROM tOOl
FailuRe:
do not use damaged
equipment. if abnormal noise
or vibration occurs, have the
problem corrected before
further use.
5. Hold the Chuck Ring with a gloved
hand and gently squeeze the trigger
with your other hand.
6. The Chuck should come off in your
gloved hand.
cleaning, Maintenance, and
lubrication
7. Install the new Chuck by reversing
the above steps.
1. beFORe eacH uSe, inspect the
general condition of the tool. Check
for loose hardware, misalignment
or binding of moving parts, cracked
or broken parts, damaged electrical
wiring, and any other condition that
may affect its safe operation.
2. aFteR uSe, wipe external surfaces
of the tool with clean cloth.
3.
waRning! if the supply cord of
this power tool is damaged, it must
be replaced only by a qualified
service technician.
SKU 3273
For technical questions, please call 1-800-444-3353.
Page 12
troubleshooting
problem
Tool will not start.
possible causes
1. Cord not connected.
likely Solutions
1. Check that cord is plugged in.
2. No power at outlet.
2. Check power at outlet. If outlet is
unpowered, disengage the trigger and
check circuit breaker. If breaker is
tripped, make sure circuit is right capacity
for tool and circuit has no other loads.
3. Tool’s thermal reset breaker
tripped (if equipped).
3. Disengage the trigger and allow tool to
cool. Press reset button on tool.
4. Internal damage or wear.
(Carbon brushes or switch, for
example.)
4. Have technician service tool.
Tool operates slowly. Extension cord too long or wire size Eliminate use of extension cord. If an
too small.
extension cord is needed, use shorter/
heavier gauge cord. See Extension Cords
in GROUNDING section.
Performance
decreases over time.
1. Accessory dull or damaged.
1. Keep cutting accessories sharp.
Replace as needed.
2. Carbon brushes worn or
damaged.
2. Have qualified technician replace
brushes.
Excessive noise or Internal damage or wear. (Carbon
rattling. brushes or bearings, for example.)
Drill bit slips in chuck 1. Jaws are loose.
2. Bit is jammed in work piece.
Have technician service tool.
1. Tighten chuck .
2. Tighten chuck, then operate tool in
reverse to back bit out of work piece.
1. Allow tool to work at its own rate.
Overheating.
1. Forcing tool to work too fast.
2. Accessory dull, damaged, or
bent.
2. Keep cutting accessories sharp.
Replace as needed.
3. Blocked motor housing vents.
3. Wear ANSI-approved safety goggles and
NIOSH-approved dust mask/respirator
while blowing dust out of motor using
compressed air.
4. Motor being strained by long or
small diameter extension cord.
4. Eliminate use of extension cord. If
an extension cord is needed, use one
with the proper diameter for its length
and load. See Extension Cords in
GROUNDING section.
Follow all safety precautions whenever diagnosing or servicing the
tool. disconnect power supply before service.
SKU 3273
For technical questions, please call 1-800-444-3353.
Page 13
pleaSe Read tHe FOllOwing caReFully
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROvIDED THE PARTS LIST AND ASSEMBLY
DIAgRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT
HE OR SHE IS qUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS
qUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/
OR DISTRIBUTOR ExPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD
BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE
BUYER ASSUMES ALL RISK AND LIABILITY ARISINg OUT OF HIS OR HER REPAIRS TO THE
ORIgINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISINg OUT OF HIS OR HER
INSTALLATION OF REPLACEMENT PARTS THERETO.
paRtS liSt
part
1
2
3
4
5
6
7
8
description
part
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
description
Chuck
Bearing 607
Retaining Ring Ø 32
Iron Bushing
Wool Washer
Spindle
Inner Bearing Cover
Ring Fender
Screw ST4.2 x 50
Washer Ø4
Key 3 x Ø10
Stator
Bearing 6002
Screw ST4.2 x 3.5
Washer Ø4
Fender Ring Ø15
Gear Housing
Needle Bearing HK071109
Gear 3
Rear Housing
Brush Holder Cap
Carbon Brush
Brush Holder
Direction Switch
Handle
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
Trigger
Key 3 x Ø10
Screw ST2.9 x 12
Screw ST4.2 x 14
Cord Clamp
Gear 2
Needle Bearing HK071109
Middle Housing
Gear 4
Cord
Handle
Spring Ø12
Screw ST4.2 x 14
Cord Protector
Chuck Screw
Auxiliary Handle (Not Shown)
Needle Bearing HK081210
Bearing 608
Fan
Rotor
Record product’s Serial number Here:
note: If product has no serial number, record month and year of purchase instead.
note: Some parts are listed and shown for illustration purposes only, and are not
available individually as replacement parts.
SKU 3273
For technical questions, please call 1-800-444-3353.
Page 14
aSSeMbly diagRaM
SKU 3273
For technical questions, please call 1-800-444-3353.
Page 15
liMited 90 day waRRanty
Harbor Freight Tools Co. makes every effort to assure that its products meet high
quality and durability standards, and warrants to the original purchaser that this product
is free from defects in materials and workmanship for the period of 90 days from the date
of purchase. This warranty does not apply to damage due directly or indirectly, to misuse,
abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity,
improper installation, normal wear and tear, or to lack of maintenance. We shall in no event
be liable for death, injuries to persons or property, or for incidental, contingent, special
or consequential damages arising from the use of our product. Some states do not allow
the exclusion or limitation of incidental or consequential damages, so the above limitation
of exclusion may not apply to you. THIS WARRANTY IS ExPRESSLY IN LIEU OF ALL
OTHER WARRANTIES, ExPRESS OR IMPLIED, INCLUDINg THE WARRANTIES OF
MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of the complaint
must accompany the merchandise. If our inspection verifies the defect, we will either
repair or replace the product at our election or we may elect to refund the purchase price
if we cannot readily and quickly provide you with a replacement. We will return repaired
products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning
the product.
This warranty gives you specific legal rights and you may also have other rights which
vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
SKU 3273
For technical questions, please call 1-800-444-3353.
Page 16
|