Harbor Freight Tools Dust Collector 45794 User Manual

DUST COLLECTOR  
SYSTEM  
Model 45794  
ASSEMBLY AND OPERATING INSTRUCTIONS  
3491 Mission Oaks Blvd., Camarillo, CA 93011  
Copyright © 2001 by Harbor Freight Tools. All rights reserved. No portion of this  
manual or any artwork contained herein may be reproduced in any shape or form  
without the express written consent of Harbor Freight Tools.  
For technical questions and replacement parts, please call 1-800-444-3353  
 
10. Use the right Dust Collector for the job. Do not attempt to force a small  
Dust Collector to adapt to a larger industrial Dust Collector. There are certain  
applications for which this Dust Collector was designed. Do not modify this  
Dust Collector and do not use this Dust Collector for a purpose for which it  
was not intended.  
11. Stay alert. Watch what you are doing; use common sense. Do not use Dust  
Collector when you are tired.  
12. Check for damaged parts. Before using Dust Colector, any part that  
appears damaged should be carefully checked to determine that it will  
operate properly and perform its intended function. Any part that is damaged  
should be properly repaired or replaced by a qualified technician.  
13. Replacement parts and accessories. When servicing, use only identical  
replacement parts. Use of any other parts will void the warranty.  
14. Do not operate Dust Collector if under the influence of alcohol or drugs.  
Read warning labels on prescriptions to determine if your judgment or  
reflexes are impaired while taking drugs. If there is any doubt, do not use the  
Dust Colector.  
15. Take caution as some woods contain preservatives such as copper  
chromium arsenate (CCA) which can be toxic. When using these  
materials extra care should be taken to avoid inhalation and minimize skin  
contact.  
16. Maintenance. For your safety, maintenance should be performed regularly  
by a qualified technician.  
Warning: The warnings, cautions, and instructions discussed in this instruc-  
tion manual cannot cover all possible conditions and situations that may oc-  
cur. It must be understood by the operator that common sense and caution  
are factors which cannot be built into this product, but must be supplied by  
the operator.  
Unpacking  
When unpacking, check to make sure the following parts are included. If any  
parts are missing or broken, please call Harbor Freight Tools at the number on  
the cover of this manual.  
1 Dust Collector Bag (Push snaps sewn in)  
12 Chrome Plated Snap Receptacles  
SKU 45794  
Page 3  
 
Assembly  
Note: This Dust Collector fits perfectly on Harbor Freight Tool’s Universal Tool  
Stand, Sku# 7769. It may fit on other 10” Table Saw or Scroll Saw metal stands.  
1. To fit onto tool stand, line up the snaps on the collector bag with base of your  
tool stand. Make a mark for each driled hole directly above each snap, all the  
way around the stand. If you wish, you can measure the distance between the  
snaps and lay out the marks accordingly.  
2. Match a drill bit to the end of the snap receptor with the phillips head, to deter-  
mine the correct hole size.  
Note: Before you drill the holes into the tool stand base, it is recommended that  
you drill into a piece of scrap or practice material to test the size of the drill hole.  
3. Screw the 12 phillips head screws (attached to the snap receptacles) into the  
drilled holes. The philips head end should snug into the inside base of the stand  
firmly enough for continual snapping and unsnapping as you empty the bag.  
Make sure the snap receptacle end faces outside and the philips end inside.  
4. Snap on bag by hand. Never hammer on snaps, they will break.  
Operation  
1. Before operation check to see that all of the snaps are firmly fastened.  
2. Begin operation and work while periodically checking the bag. Do not let the  
bag become more than two thirds full. A full bag causes too much stress on the  
snaps.  
3. Put on goggles and dust mask to empty bag.  
Maintenance  
1. Check snap receptacles and make sure they are firmly in place.  
2. Check bag for tears.  
Note: No replacement parts are available for the Dust Collectior System.  
SKU 45794  
Page 4  
 

Grizzly Nail Gun G3690 User Manual
Grizzly Trimmer T20797 User Manual
Haier Air Conditioner HWF05XCK User Manual
Haier Dishwasher DWL2825 User Manual
HANNspree Flat Panel Television SK Series User Manual
Honeywell Home Security System K9696V2 User Manual
Hunter Fan Outdoor Ceiling Fan 21321 User Manual
Husqvarna Snow Blower ST 224 User Manual
IBM Computer Monitor 8183 User Manual
Icom Car Stereo System IC R100 User Manual