2-STEP FOOT SWITCH
Model 96618
FOOT SWITCH
Model 96619
SET uP AND INSTruCTIONS
Diagrams within this manual may not be drawn proportion.
®
Distributed exclusively by Harbor Freight Tools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANuAl.
©
®
Copyright 2007 by Harbor Freight Tools . All rights reserved. No portion of
this manual or any artwork contained herein may be reproduced in any shape
or form without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
SAVE THIS MANuAl
Keep this manual for the safety warnings and precautions, assembly, operating,
inspection, maintenance and cleaning procedures. Write the product’s serial number in
the back of the manual near the assembly diagram (or month and year of purchase if
product has no number). Keep this manual and the receipt in a safe and dry place for
future reference.
SET uP INSTruCTIONS
read All of the SPECIFIC SAFETy rulES on the previous page,
including all text under subheadings therein before set up or use of this
product.
risk of electric shock! Do not use near water or in damp
conditions. The switch mechanism is not insulated.
WArNING
Only use with grounded 120V outlet. Do not use with tool
rated higher than 120VAC, 15A.
Please note: the following setup instructions apply to both
the 96618 2-Step Foot Switch and the 96619 Foot Switch.
1.
2.
Make sure the tool used with the Foot Switch (router, scroll saw, wood carving
tool, for example) is in the OFF position, disconnected.
Place the Foot Switch in a location that it will be easy to reach during use.
CAuTION! The Foot Switch is intended for temporary hands-free use only and
not in place of a permanent ON/OFF power switch for the tool.
3.
Mounting holes are available on either end of the Foot Switch base. This will
keep the Foot Switch in place and prevent any kind of accidental kicking or
movement.
4.
5.
If mounting, make sure the installation surface is free of any hidden wires or
cables.
If needed, the Foot Switch can be placed on the work table and used by hand.
CAuTION! Hand-use should only be done if neither foot can reach or control
the Foot Switch during use. Do not use your hand to control the foot switch if
both hands are required to operate tool.
6.
7.
Once the Foot Switch is placed in the proper location in the work area (under the
work table or near your chair) that can be reached by your foot (or hand), plug
the cord of Foot Switch into a grounded 120V outlet.
Plug the power cord into the 3-prong outlet located at the end of the Foot
Switch.
The Foot Switch is now ready to be used as the tool’s ON/OFF Switch.
WArNING for the 96618 Foot Switch! In case of a blown fuse or tripped breaker
switch when foot switch is in use, please turn off the foot switch prior to replacing the
fuse or resetting the breaker. Unplugging the tool from the foot switch is preferable.
This will help insure that the tool does not power on unexpectedly after replacing the
fuse.
07h
96618 / 96619 For technical questions, please call 1-800-444-3353.
Page 3
OPErATING INSTruCTIONS
The following operating instructions are for the 96618 Foot Switch ONly:
1.
Once the 2-Step Foot Switch is properly set-up, use your foot (or hand) to step
or press down on the pedal once. remove your foot or hand.
2.
3.
The tool will now activate, allowing you to work with both hands.
To turn off the tool, press down on the pedal again. This will turn off the tool.
Please note: Avoid accidental starting/stopping. Do not step on the Foot Switch
unless you intended to turn on/off the tool
4.
To reactivate the tool, simply step or press down on the pedal again.
The following operating instructions are for the 96619 Foot Switch ONly:
1.
Once the Foot Switch is properly set-up, use your foot (or hand) to step or press
down on the pedal. yOU SHOUlD KeeP yOUr FOOT Or HAND ON THe
PeDAl DUrINg USe. removal of foot or hand pressure will deactivate the
switch and stop the unit connected to the Foot Switch.
2.
3.
The tool will now activate, allowing you to work with both hands.
To turn off the tool, remove your foot or hand from the pedal. This will turn off
the tool.
Please note: Avoid accidental starting/stopping by maintaining the same
amount of pressure on the Foot Switch.
4.
To reactivate the tool, simply step or press on the pedal again. Do not remove
your foot or hand from the Foot Switch.
MAINTENANCE AND SErVICING
1.
2.
BEFOrE EACH uSE, inspect the general condition of the Foot Switch. Check
for loose parts, cracked and/or any other damage that may affect safe operation.
When finished using Foot Switch, unplug from grounded outlet and tool and
store in a safe location out of the reach of children.
PlEASE rEAD THE FOllOWING CArEFully
THe MANUFACTUrer AND/Or DISTrIBUTOr HAS PrOVIDeD THe PArTS lISTANDASSeMBly DIAgrAM IN THIS MANUAl
AS A reFereNCe TOOl ONly. NeITHer THe MANUFACTUrer Or DISTrIBUTOr MAKeS ANy rePreSeNTATION Or
WArrANTy OF ANy KIND TO THe BUyer THAT He Or SHe IS qUAlIFIeD TO MAKe ANy rePAIrS TO THe PrODUCT,
Or THAT He Or SHe IS qUAlIFIeD TO rePlACe ANy PArTS OF THe PrODUCT. IN FACT, THe MANUFACTUrer AND/
Or DISTrIBUTOr exPreSSly STATeS THAT All rePAIrS AND PArTS rePlACeMeNTS SHOUlD Be UNDerTAKeN By
CerTIFIeD AND lICeNSeD TeCHNICIANS, AND NOT By THe BUyer. THe BUyer ASSUMeS All rISK AND lIABIlITy
ArISINg OUT OF HIS Or Her rePAIrS TO THe OrIgINAl PrODUCT Or rePlACeMeNT PArTS THereTO, Or ArISINg
OUT OF HIS Or Her INSTAllATION OF rePlACeMeNT PArTS THereTO.
96618 / 96619 For technical questions, please call 1-800-444-3353.
Page 4
|