Instruction booklet
Contents
GB
GB
Installation, 2-3
Where to put your dryer
Ventilation
English
Water drain
Levelling
Electrical connection
Before you start using your dryer
Warnings, 4-5
General safety
To minimise the risk of fire
Maintenance and Care, 6-7
Switching off the electricity
TDHP 871
Cleaning the filter after each cycle
Empty the water container after each cycle
Cleaning the heat pump filter unit
Check the drum after each cycle
Cleaning the dryer
First time you turn on your dryer
you must select your preferred
language see page 9
Dryer description, 8
The features
Control panel
Choosing a programme
TUMBLE DRYER
The Display, 9-11
This symbol reminds you to read this
booklet.
Start and programmes, 11-14
The Controls
Programmes Table
! Keep this instruction booklet on hand in order to refer
to it when necessary. Take it with you when you
move, and should you sell this appliance or pass it
on to another party, make sure that this booklet is
supplied along with the dryer so that the new owner
may be informed about warnings and suggestions on
how the appliance works.
Laundry, 15
Sorting your laundry
Wash care labels
Drying times
Troubleshooting, 16
! Read these instructions carefully; the following
pages contain important information on installation
and suggestions on how the appliance works.
Service, 17
Spare Parts
Product data, 18
Recycling and Disposal
To activate your free* 5 Year Parts Guarantee
Call free on 0800 519 2102
*Labour charges not included. Terms and consitions apply. Lines open 364 days a year.
Calls are free from a BT landline. Charges from other providers and mobiles may apply.
1
Installation
Electrical connections
Before you start using your dryer
Once you have installed your dryer and before you
use it, clean the inside of the drum to remove any dust
that could have accumulated during transport.
GB
Make sure of the following before you
insert the plug into the the electrical socket:
●
Make sure your hands are dry.
●
The socket must have an earth connection.
●
The socket must be able to sustain the
machines maximum power, which is
indicated on the rating label (see Dryer
Description).
Maximum load
Natural fibres : 8 kg
●
Power voltage must be within the values
indicated on the rating label (see Dryer
Description).
●
The socket must be compatible with the
dryers plug. Should this not be the case,
replace the plug or the socket.
! The dryer must not be installed outdoors,
even if the space is sheltered. It can be
very dangerous if it is exposed to rain or
storms.
! Once installed, the dryers electrical wire
and plug must be within easy reach.
! Do not use extension cords.
! The power cord must not be bent or
squashed.
! The power cord should be regularly
checked. If the supply cord is damaged, it
must be replaced by the manufacturer, its
service agent or similarly qualified
persons in order to avoid a hazard. New or
longer power cords are supplied at an extra
charge by authorised dealers.
! The manufacturer denies any responsibility
should any of these rules not be followed.
! If in doubt about any of the above consult a
qualified electrician.
3
Warnings
●
●
Check to see if the dryer is empty before
loading it.
! The appliance has been designed and
built according to international safety
standards.
These warnings are given for safety
reasons and must be followed carefully.
GB
The back of the dryer could
become very hot. Never touch it
while in use.
●
Do not use the dryer unless the filter,
water container and heat pump filter unit
are securely in place (see Maintenance).
Do not overload the dryer (see Laundry
for maximum loads).
General safety
●
This appliance can be used by children
●
aged from 8 years and above and
persons with reduced physical, sensory
or mental capabilities, or lack of
●
●
Do not load items that are dripping wet.
Carefully check all instructions on
clothing labels (see Laundry).
Do not tumble dry large, very bulky
items.
knowledge if they are given supervision
or instruction concerning use of the
appliance in a safe way and understand
the hazards involved.
●
●
●
●
●
●
●
●
●
●
●
●
Do not tumble dry acrylic fibres at high
temperatures.
This tumble dryer has been designed for
home, and not professional use.
●
Complete each programme with its Cool
Tumble Phase.
Do not touch the appliance while bare
foot or with wet hands or feet.
●
Do not turn off the dryer when there are
still warm items inside.
Unplug the machine by pulling on the
plug, not the cord.
●
Clean the filter after each use (see
Maintenance).
After using the dryer, turn it off and
unplug it. Keep the door closed to make
sure that children do not use it as a toy.
Empty the water container after each
use (see Maintenance).
●
Children should be supervised to ensure
Clean the heat pump filter unit at regular
intervals (see Maintenance).
Do not allow lint to collect around the
dryer.
that they do not play with the dryer.
●
Cleaning and user maintenance should
not be made by children without
supervision.
●
Never climb on top of the dryer. It could
result in damage.
Always follow electrical standards and
requirements (see Installation).
Always buy original spare parts and
accessories (see Service).
Children of less than 3 years should be
kept away from the appliance unless
continuously supervised.
●
The appliance must be installed correctly
and have proper ventilation. The air
intake at the front of the dryer and rear
vent behind the dryer should never be
obstructed (see Installation).
●
Never use the dryer on carpeting where
the pile height would prevent air from
entering the dryer from the base.
4
Warnings
To minimise the risk of fire in your
tumble dryer, the following should be
observed:
or explosive substances. Highly flammable
substances commonly used in domestic
environments including cooking oil,
acetone, denatured alcohol, kerosene,
spot removers, turpentine, waxes and
wax removers. Ensure these items have
been washed in hot water with an extra
amount of detergent before being dried
in the tumble dryer.
Do not tumble dry items containing foam
rubber (also known as latex foam), or
similarly textured rubber like materials.
Foam rubber materials can, when
heated, produce fire by spontaneous
combustion.
Fabric softener or similar products
should not be used in a tumble dryer to
eliminate the effects of static electricity
unless the practice is specifically
recommended by the manufacturer of
the fabric softener product.
GB
●
Tumble dry items only if they have been
washed with detergent and water, rinsed
and been through the spin cycle. It is a
fire hazard to dry items that HAVE NOT
been washed with water.
●
Do not dry garments that have been
treated with chemical products.
●
●
●
●
Do not tumble dry items that have been
spotted or soaked with vegetable or
cooking oils, this constitutes a fire hazard.
Oil-affected items can ignite spontaneously,
especially when exposed to heat sources
such as a tumble dryer. The items become
warm, causing an oxidisation reaction with
the oil, Oxidisation creates heat. If the heat
cannot escape, items can become hot
enough to catch fire. Piling, stacking or
storing oil-effected items can prevent heat
from escaping and so create a fire hazard.
If it is unavoidable that fabrics containing
vegetable or cooking oil or those that have
been contaminated with hair care products
be placed in a tumble dryer they should
first be washed with extra detergent - this
will reduce, but not eliminate the hazard.
The cool tumble phase should be used to
reduce the temperature of the items. They
should not be removed from the dryer and
piled or stacked while hot.
Do not tumble dry undergarments that
contain metal reinforcements eg. bras
with metal reinforcing wires. Damage to
the tumble dryer can result if the metal
reinforcements come loose during drying.
Do not tumble dry rubber, plastic articles
such as shower caps or babies water
proof covers, polythene or paper.
Do not tumble dry rubber backed
articles, clothes fitted with foam rubber
pads, pillows, galoshes and rubber
coated tennis shoes.
●
●
●
Do not tumble dry items that have
previously been cleaned in or washed in,
soaked in or soiled with petrol/gasoline,
dry cleaning solvents or other flammable
●
Remove all objects from pockets,
especially lighters (risk of explosion).
! WARNING: Never stop the dryer before the end of the drying cycle unless all items are
quickly removed and spread out so that the heat is dissipated.
5
Maintenance and Care
Switching off the electricity
! Failure to empty the water container may cause
the following:
GB
! Unplug your dryer when not using it,
when cleaning it and during all
maintenance operations.
- The dryer will stop heating (so the load may still
be damp at the end of the drying cycle).
●
Priming the water collection system
When your dryer is new, the water container will not
collect water until the system is primed.
This will take 1 or 2 drying cycles. Once primed it will
collect water during every drying cycle.
Clean the filter after each cycle
The filter is an important
part of your dryer:
it accumulates lint and
fluff that is formed while
drying.
Cleaning the heat pump filter unit
Periodically (every 5 drying cycles) remove
the heat pump filter unit and clean any
build up of fluff from the surface of the filter.
However, we recommend that you clean
this filter after EVERY drying cycle to
optimise the dryers performance.
When finished drying, clean the filter by
rinsing it under running water or with your
vacuum cleaner. Should the filter become
clogged up, the airflow inside the dryer will
be seriously compromised: drying times
lengthen and you will consume more
energy. It may also damage your dryer.
To removing the heat pump filter unit:
1. Unplug the dryer and open the door.
2. Pull open the heat pump filter unit cover
(see diagram on next page).
Release the 4 clips to the vertical position
then pull the filter unit towards you.
3. Separate the two parts
The filter is found in front of the dryer trim
(see diagram on next page).
Removing the filter:
of the filter and clean
the surface of the filter.
1. Pull the plastic grip of
the filter upwards.
2. Clean the filter and
replace it correctly.
Ensure the filter is fully
located flush into
the tumble dryer trim.
! The front of the heat pump is made
from thin metal plates. Take care that you
do not damage these or cut yourself when
cleaning, removing or replacing the heat
pump filter unit.
! Do not use the dryer without replacing
the filter.
Empty the water container after each
cycle
4. If there is any build up of fluff on the
plates, carefully clean this off with a damp
cloth, sponge or a vacuum cleaner. Never
use your fingers.
5. Reassemble the two parts of the filter,
clean the seals and replace with the 4
clips in the horizontal position, make
sure that the catches are secure.
Pull the container out of the dryer
and empty it into a sink or other
suitable drain.
Replace the water container
securely.
! Always check and empty the container before you
start a new drying programme.
6
Maintenance and Care
GB
Water container
Filter
Heat pump filter unit
Air intake
Heat pump filter
unit cover
Handle
Clips
Check the drum after each cycle
Quick Tips
●
Turn the drum manually in order to remove small items
(handkerchiefs) that could have been left behind.
Remember to clean the door filter and
heat pump filter after each load.
Remember to empty the water container
after each load.
●
Cleaning the drum
! Doing BOTH the above will keep your
appliance working at its BEST.
! Do not use abrasives, steel wool or stainless steel
cleaning agents to clean the drum.
A coloured film may start to appear on the stainless
steel drum, this may be caused by a combination of
water and, or cleaning agents such as fabric conditioner
from the wash. This coloured film will not affect the
dryer performance.
Cleaning the dryer
●
External parts in metal or plastic and rubber parts
can be cleaned with a damp cloth.
Periodically (every 6 months) vacuum the front air
●
intake grille and vents at the rear of the dryer, to
remove any build up of fluff, lint or dust. Also to
remove accumulation of fluff from the front of the
heat pump and filter areas, clean occasionally with
a vacuum cleaner.
! Do not use solvents or abrasives.
! Your dryer uses special bearing components which
do not need lubrication.
! Have your dryer checked regularly by authorised
technicians to ensure electrical and mechanical safety
(see Service).
7
Dryer Description
To open the door
The features
GB
ting plate
Press and release the front
panel in position shown
Model &
Serial
numbers
Heat Pump
Filter Unit
(cover open)
Air intake
grille
Heat Pump Filter cover
handle (Pull to open)
Filter
Adjustable Feet
Control panel
PROGRAMME
Display Unit
Selection Buttons
CHILD LOCK &
OPTIONS
Buttons & Lights
ON/OFF
Button
START/PAUSE
Button & Light
The ON/OFF button
- if pressed when the dryer is
flashing green if on standby waiting to start a programme
(see Start and Programmes).
running: If the display shows TURNING OFF the
dryer stops. If the display shows PRESS AND HOLD
hold the botton and the display counts down 3, 2, 1
and then stops.
Note: This light also flashes amber during the Post
Care phase of a programme.
Press and hold again for more than 3 seconds, the
display briefly shows POWER ON .
The Display Unit gives warnings and information
about the programme selected and its progress (see
next page).
The PROGRAMME selection buttons set the programme:
press the button corresponding to the programme you
want to select (see Start and Programmes).
The CHILD LOCK button/icon
: Press and hold this
button after selecting your programme and any options,
this prevents the programme settings from being
changed, the display will briefly show LOCKED .
When the icon is lit, the other buttons are disabled.
Hold the button to cancel and the icon will go out, the
display will briefly show UNLOCKED .
The OPTION buttons/indicators: these buttons select
available options for your selected programme (see
The Controls). The indicators on the display unit next
to the bottom buttons light to show that the option has
been selected.
Note: This tumble dryer, in compliance with new energy
saving regulations, is fitted with an automatic standby
system which is enabled after about 30 minutes if no
activity is detected. Press and hold the ON-OFF
button until the display briefly shows POWER ON
and the dryer then reactivates.
The START/PAUSE button/light
starts a selected
programme. When you press this button there will be
one beep and the display will show PAUSE . When
a programme is running, holding this button in pauses
the programme and stops the dryer.
The light is green when the programme is running,
flashing amber if the programme has been paused or
8
The Display
Selecting your language
The first time you turn on your dryer you should select your preferred language from the available list.
GB
To change: the language current selection must flash, on
the first line of the display.
- Press the On/Off button to turn off the display then press
and hold all 3 buttons:
Heat Level,
Timed Dry
and
Dryness Level for 5 seconds.
- Press the
Heat Level or the
Timed Dry button to
scroll up or down through the list.
- When your required language is flashing on the top line
of the display, pressing the
select your choice.
Dryness Level button will
Understanding the display
Programme selection and display
The selected programme is shown on the first line of the display
when you select the corresponding button, this message is shown
while the programme is running.
COTTONS
SHIRTS
SYNTHETICS
BED & BATH
EASY IRON
REFRESH
DELICATES
WOOL
MY CYCLE (see below)
M
My Cycle When you select the My Cycle button the Display will show your selected programme with ‘M’ before its
name. ie. M COTTONS (see Start and Programmes).
Dryness levels
During programme selection for an automatic programme that has different dryness levels available (see Programmes
Table).
The second line of the display shows the dryness level you require, for each
press of the
Dryness Level button the next option from the list below is
selected and displayed. The display also shows 1 to 7 bars depending on
your selection and these are displayed during the programmes progress.
! Some automatic programmes do not allow the dryness level to be changed
or do not have all the dryness level options.
DAMP
Dries your items ready to be ironed using a machine or rotary ironer.
IRON DRY
Dries your items ready to be ironed with a hand iron.
Dries your delicate items ready to be hanged for final drying.
Dries your items ready to be hanged for final drying.
Dries your delicate items ready to be put away.
Dries your items ready to be put away.
HANGER PLUS
HANGER DRY
LIGHT DRY
CUPBOARD DRY
EXTRA DRY
Dries your clothes ready to be worn.
9
The Display
Programme progress
GB
The second line of the display shows the status of the programme as it progresses:
(long messages scroll across the line)
DRY
COOL TUMBLE
(if option Post Care selected).
END OF CYCLE, CREASE CARE
END OF CYCLE, CLEAN FILTER AND EMPTY WATER BOTTLE
Timed drying
After selecting a programme that has a Timed Dry option,
press the Timed button and the display will increment the
selected time, each time you press and release the button
(see Start and Programmes).
Each press reduces the time duration and number of available time options depending on the programme/material
selected.
The Timed Dry icon
is displayed next to the time.
The selected time remains displayed after the programme starts, but can be changed anytime you wish.
Delay and Time to End
Some programmes can have a delayed start (see Start and Programmes). Press the
Each press of the Delay button advances the delay setting
Delay button and the icon flashes.
in 1 hour increments, from: , then and
to
24h
1h
OFF
then after a couple of seconds cancels the delay.
The delay time is shown on the display next to the Delay button.
The display counts down the minutes of the delay period after
the Start/Pause button
is pressed.
The second line of the display shows STARTS IN
You can change or cancel the delay time selected anytime if
you wish.
After the Start/Pause button is pressed the Delay or Time to End is displayed in hours and minutes and counts down each
minute.
Time to End
After the delay period finishes, or for all the programme if delay not selected:
- the estimated time to the end of the programme, for automatic programmes or the actual time remaining during a
timed programme is shown in this part of the display.
When timed programmes are selected the time displayed throughout the cycle is the actual time remaining.
When Automatic programmes are selected the time displayed is an estimate of the time remaining. When the
programme is selected the display shows the time required to dry a full load. The time remaining is constantly
monitored during the drying cycle and is updated to show the best forecast.
The colons between the hours and minutes in the display flash to show the time is counting down.
10
The Display
Warnings
GB
The second line of the display also gives warnings and reminders:
(reminders occur at the end of the programme)
END OF CYCLE, CLEAN FILTER AND EMPTY WATER BOTTLE
●
Reminder that the water container should be
emptied and the filter cleaned every time you use the
dryer (see Maintenance).
CLEAN CONDENSER, FILTER AND EMPTY WATER BOTTLE
EMPTY WATER BOTTLE
●
This message indicates that you must clean the
Heat Pump Condenser Filter unit (see Maintenance)
and will occur at intervals depending how much you
have used the dryer. When you finish the next
programme the message is cancelled. You must also
clean the filter.
●
Indicates that the water container is full. The
message will take a few seconds to go out after
replacing the empty water container; the dryer
must be running for this to happen (see The
Controls).
Note: If the water container fills and this message
is displayed, the heat is turned off and your
clothes will not dry.
Start and Programmes
Choosing a programme
During the drying programme, you can check on
your laundry and take out items that are dry while
others continue drying. When you close the door
1. Plug the dryer into the electrical socket.
2. Sort your laundry according to fabric type (see
Laundry).
again, press the Start/Pause button
resume drying.
in order to
3. Open the door and make sure the filter is clean
and in place and the water container is empty and
in place (see Maintenance).
If you open the door to check your laundry you
will extend the drying time as the heat pump
compressor will not start for 5 minutes after you
close the door and press the Start/Pause button
(see The Controls).
4. Load the machine and make sure items are not
in the way of the door seal. Close the door.
5. If the Display is not lit: Press the ON/OFF button
6. Press the Programmes Selection button that
corresponds with the type of fabric being dried by
checking the Programmes Table (see Programmes)
as well as the indications for each type of fabric (see
Laundry).
10. During the last few minutes of Drying Programmes,
before the programme is completed, the final COOL
TUMBLE phase is entered (fabrics are cooled),
this phase should always be allowed to complete.
11. At the end of the drying cycle a message is
displayed:
- If the
required (see below).
button is selected; steps 7 and 8 are not
-
If END OF CYCLE, CLEAN FILTER AND EMPTY WATER BOTTLE
is shown, the buzzer will beep 3 times (Note: If
the SOUND option was selected the buzzer
beeps 3 times every 30 seconds for 5 minutes).
If END OF CYCLE, CREASE CARE is shown, Post
Care option has been selected and if you do
not remove the laundry immediately, the
dryer will tumble occasionally for 10 hours or
until you open the door, the buzzer will beep
3 times to confirm the programme is completed.
7. Choose Timed Drying or Dryness Levels option:
- If Timed Drying press and release the Timed
button until the required time is displayed.
or - To change from default dryness setting, press
and release the Dryness Levels button until
required level is indicated.
-
! See Programmes Table, for more details:
availability of Dryness Levels, Timed Dry and
Options.
12. Open the door, take the laundry out, clean the filter
and replace it. Empty the Water Container and
replace it (see Maintenance).
8. Set a delay time and other options if necessary
(see The Display).
9. Press the Start/Pause button
to begin.
13. Unplug the dryer.
The display will show the estimated time to end.
My Cycle button:
First time you press this button the display will show PRESS AND HOLD TO STORE
After selecting your favorite programme and options you can save these settings by pressing and holding in the
My Cycle button for at least 5 seconds, the top line will show a flashing
buzzer will then beep and the second line of the display shows MEMORY
followed by the selected programme. The
The next time you need this programme press the button, then the Start/Pause button
If you wish, you can change your stored favorite, by selecting a new programme and/or options and press and hold
in the button (as above).
and this programme will run.
11
Start and Programmes
Programmes Table
! If the Display is not lit; Press the ON/OFF button
GB
and then select programme.
Programme
Options available
Dryness Levels available
(default highlighted
)
✓
- High
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✗
✓
✗
✓
✓
Standard Cotton
✓
✓
✓
✓
- Medium
- Low
- High
*
*
*
Shirts
✓ ✓
✗
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✗
✓
- Medium
- Medium
- Low
✓
✗
Synthetics
✓ ✓
✓
✓
✓
✗
✓
- High
✓
✗
✗
✗
✗
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
Bed & Bath
Wool
✓
✓
✗
*
✓
- Medium
●
An Automatic programme
✗
✓
✗
✗
✗
✗
✗
✗
✗
✗
✗
✗
✗
✓
✗
✗
✓
✗
✓
✓
✓
✓
✓
✗
✓
Delicates
Easy Iron
Refresh
✓
*
✓
✓
●
An Automatic programme
An Automatic programme
✗
✗
●
✗
✗
*YOU CANNOT SELECT BOTH POST CARE AND SOUND OPTIONS
Standard Cotton
●
This is a programme for cotton items.
●
The duration of this programme will depend on the size of the load, the dryness setting selected and the spin
speed used in your washer (see Laundry).
The Standard Cotton programme to EU Regulation 392/2012 is Programme 1 selection with High Heat and
Dryness Level Cupboard Dry.
●
Shirts
High heat option
●
●
This is a programme for shirts made from cotton.
It can be used for load sizes up to 3kg (approximately 10 shirts).
Medium heat option
●
●
This is a programme for shirts made from synthetic materials or a mixture of natural and synthetic materials, such
as polyester and cotton.
It can be used for load sizes up to 3kg (approximately 14 shirts).
The duration of this programme will depend on the size of the load, the dryness setting selected and the spin
speed used in your washer.
Loads dried using the Cupboard Dry setting are usually ready to wear, the edges or seams may be slightly damp. If
this is the case, try turning the shirts inside out and running the programme again for a short period.
Synthetics
●
This is a programme for items of Synthetic with low heat setting or Synthetic/Cotton mixtures with medium heat
setting.
●
The duration of this programme will depend on the size of the load, the dryness setting selected and the spin
speed used in your washer (see Laundry).
Bed & Bath
●
This is a programme for cotton towels and sheets.
●
The duration of this programme will depend on the size of the load, the dryness setting selected and the spin
speed used in your washer (see Laundry).
●
Loads dried using the Extra Dry setting are usually ready to use, the edges or seams may be slightly damp
especially on large items. If this is the case, try opening them out and running the programme again for a short
period.
12
Start and Programmes
Wool Programme
GB
●
This is a programme for tumble dryer safe garments marked with the symbol
.
●
It can be used for load sizes up to 1kg (approximately 3 sweaters).
●
We recommend that garments are turned inside out before drying.
●
This programme will take about 60 minutes, but may take longer depending on the size and density of the load
and the spin speed used in your washer.
●
Loads dried using this programme are usually ready to wear, but on some heavier garments the edges may be
slightly damp. Allow these to dry naturally as over-drying could damage garments.
! Unlike other materials, the mechanism of wool shrinkage is irreversible; i.e. it will not stretch back to original size and
shape.
! This programme is not suitable for Acrylic garments.
Delicates
●
This is a programme for drying your delicate clothes ie. Acrylics.
●
It can be used for load sizes up to 2kg.
●
The duration of this programme will depend on the size and density of the load and the spin speed used in your
washer.
●
Loads dried using this programme are usually ready to use, but on some garments the edges may be slightly
damp. If this is the case, try opening them out or turn items inside out and running the programme again for a short
period.
Easy Iron Programme
‘Easy Iron’ is a short 10 minute programme (8 minutes of heat followed by a 2 minute cool tumble period) which
fluffs the fibres of clothing that have been left in the same position/location for an extended period of time. The cycle
relaxes the fibres and makes them easier to iron and fold.
! ‘Easy Iron’ is not a drying programme and should not be used for wet articles of clothing.
For best results: 1. Do not load more than the maximum capacity. These numbers refer to the dry weight:
Fabric
Maximum load
Cotton and Cotton mixtures
Synthetics
2.5kg
2kg
Denim
2kg
2. Unload the dryer immediately after the end of the programme, hang, fold or iron the articles
and put them away in the closet. Should this not be possible repeat the programme.
The ‘Easy Iron’ effect varies from one fabric to the next. It works well on traditional fabrics like Cotton or Cotton mix,
and less well on acrylic fibres and on materials such as Tencel®.
Refresh
! ‘Refresh’ is not a drying programme and should not be used for wet articles of clothing.
●
It can be used on any load size but is more effective on smaller loads.
●
Do not overload your dryer (see Laundry).
●
This is a 20 minute programme that airs your clothes with cool air. Also use to cool warm clothes.
13
Start and Programmes
●
88:88
TIME DISPLAY
The Controls
GB
The display shows either the amount of time delay
remaining or an indication of the amount of time left for a
drying programme (see The Display).
The display also shows if there is a problem with your
dryer, if this occurs the display will show F followed by a
fault code number (see Troubleshooting).
! Warning, after pressing the Start/Pause button
programme cannot be changed.
, the
To change a selected programme, press the Start/Pause
button , the light flashes Amber to indicate the
programme is paused. Select the new programme and
any options required, the light will then flash green. Press
the Start/Pause button
will start.
●
Empty Water Container
again and the new programme
(If you have plumbed your dryer to a drain this icon can be
ignored, as there is no need to empty the water container).
Messages are displayed to reminds you to empty the
water container (see The Display).
●
Option buttons
These buttons are used to customise the selected
programme to your requirements. A programme must
have been selected, by pressing a programme selection
button, before an option can be selected. Not all options
are available for all programmes (see Programmes
Table). If an option is not available and you press the button,
the buzzer will beep 3 times. If the option is available the
indicator, on the display unit next to the bottom buttons,
lights to show that the option has been selected.
Delay Timer (Time Delay)
If the water container fills during a programme, the heater
turns off and the dryer does a period of Cool Tumble.
After this it stops and a message tells you to
EMPTY THE WATER CONTAINER .
You must empty the water container and restart the dryer
or the clothes will not dry. After re-starting the dryer the
message will take a few seconds to go out.
To avoid this always empty the water container each time
you use the dryer (see Maintenance).
●
Door Opening
The start of some programmes (see The Display and
Programmes tables) can be delayed for up to 24 hours.
Ensure the water container is emptied before setting a
delayed start.
Opening the door during a programme will stop the dryer
and have the following effects:
Note: The Start/Pause light flashes Amber during the Post
Care phase of a programme.
●
Pre Care
The display shows PAUSED .
During a delay phase the delay will continue to count
down. The Start/Pause button must be pressed to
resume the delay programme.
The display will change to show current status.
The Start/Pause button must be pressed to resume
the programme. The display will change to show the
current status, the colons flash and count down
continues.
●
This option is only available if a delayed start has been
selected. It tumbles the clothes occasionally during the
delayed period to help prevent creases developing.
Post Care
When available and selected, the clothes are
occasionally tumbled after the end of the drying and cool
tumble cycles, to help prevent creases developing
should you not be available to remove the load
immediately the programme is complete.
●
●
During the Post Care phase, the programme ends.
Pressing the Start/Pause button will restart a new
programme from the beginning.
Note: The Start/Pause light flashes Amber during this phase.
Note: If you have selected the Sound option this option is
not available.
●
Heat Pump Protection System
The heat pump system has a compressor protection
feature that operates if you open the door or there is a
power disruption or if you turn off the dryer. This system
will prevent the heat pump compressor from starting for 5
minutes after the door is closed and the programme is
started.
Heat Level button, Display and Icons
Not all programmes allow you to change the heat level
and some programmes allow all three heat level options:
Low, Medium and High.
When the heat level options are available pressing this
button changes the heat level and the display briefly shows
the selected heat level, along with a display of the selected
level icon:
●
Note
If you have a power cut, switch off the power or remove
the plug. When power is restored, press and hold the
On/Off button until the display briefly shows POWER ON
and the dryer reactivates. Then press the Start/Pause
button and the programme will resume.
HIGH HEAT
MEDIUM HEAT
LOW HEAT
Sound
Available on all programmes and allows the buzzer to
give a signal at the end of the drying cycle, to remind
you that the clothes are ready to be removed.
Note: If you have selected the Post Care option this
option is not available.
Mini Load
Available with programmes :
Cotton High Heat 4kg and Synthetic Medium Heat 1kg.
This option optimises Automatic programme for smaller
loads and improves the Time to End estimation.
14
Laundry
Sorting your laundry
Drying times
●
GB
Check symbols on clothing labels to make sure
that the articles can be tumble dried.
Sort laundry by fabric type.
Empty pockets and check buttons.
Close zippers and hooks and tie loose belts and
strings.
The table (see below) presents APPROXIMATE drying
times in Minutes. Weights refer to dry garments.
●
●
●
Times are approximate and can vary depending
upon:
●
Amount of water retained in clothes after spin
●
Wring out each item in order to eliminate as much
excess water as possible.
cycle: towels and delicates retain a lot of water.
! Do not load dripping wet clothes into the dryer.
●
Fabrics: items that are the same type of fabric but
different textures and thicknesses may not have
the same drying time.
Maximum load size
Do not load more than maximum capacity.
These numbers refer to dry weight:
Natural fibres: 8kg max (18lb)
●
Quantity of laundry: single items or small loads
may take longer to dry.
Synthetic fibres: 3kg max (6.6lb)
●
Dryness: If you are going to iron some of your
! DO NOT overload the dryer as this could result in
reduced drying performance.
clothes, they can be taken out while still a bit
damp. Others can be left longer if you need them
to be completely dry.
Wash Care Labels
●
Heat setting.
Look at the labels on your garments, especially when
tumble drying for the first time. The following symbols
are the most common:
●
Room temperature: if the room where the dryer is
located is cold, it will take longer for the dryer to
dry your clothes.
●
Bulk: some bulky items can be tumble dried with
May be tumble dried
care. We suggest that you remove these items
several times, shake them out, and return them to
the dryer until finished.
Do not tumble dry
Tumble dry at high heat setting
Tumble dry at low heat setting
! Do not over-dry your clothes.
All fabrics contain a little natural moisture, which
keeps them soft and fluffy.
Cottons
2 kg
3 kg
4 kg
2:00 - 2:20
6 kg
2:30 - 3:10
7 kg
2:50 - 3:20
1 kg
1:00 - 1:30
60 - 90
5 kg
2:20 - 3:00
8 kg
3:20 - 4:00
Automatic duration
Automatic minutes
Timed Dry setting
1:20 - 1:40 1:40 - 2:10
80 - 100
120 - 140
150 - 190
170 - 200
120 - 130
140 - 180
2:30
200 - 240
High
Heat
1:30
3:40
1:30 or 2:00
2:30 or 3:00
2:00 or 2:30
3:00 or 3:40
1:00 or 1:30
Drying times 800-1000 rpm in washing machine.
Synthetics
2 kg
1 kg
3 kg
Automatic duration
0:40 - 0:50
0:50 - 1:10
50 - 70
0:40 or 1:00
1:10 - 1:30
70 - 90
1:00 or 1:30
40 - 50
Automatic minutes
Timed Dry setting
Medium
Heat
0:40 or 1:00
Drying times on reduced spin in washing machine.
Delicates
(Acrylics)
2 kg
1:20 - 2:20
1 kg
Automatic duration
0:40 - 1:20
80 - 140
Automatic minutes
Timed Dry setting
40 - 80
1:30 or 2:00 or 2:30
0:40 or 1:00 or 1:30
Low
Heat
Drying times on reduced spin in washing machine.
●
Note: At the end of a drying cycle, cottons could still be damp if you grouped cottons and synthetics together.
If this is the case, simply give the damp cotton items an additional short period of drying.
15
Troubleshooting
One day your dryer seems not to be working. Before you call your Service Centre (see Service), go through the
following troubleshooting suggestions:
GB
Problem:
Possible causes / Solution:
●
The tumble dryer won’t start.
The plug is not plugged into the socket, or not making contact.
There has been a power failure.
The fuse has blown. Try to plug another appliance into the socket.
You are using an extension cord? Try to plug the dryer’s power cord
●
●
●
directly into the socket.
The door is not closed securely?
The programme has not been set properly (see Start and Programmes).
The Start/Pause button has not been pressed (see Start and Programmes).
●
●
●
●
Drying cycle will not begin.
Its taking a long time to dry.
You have set a delayed time (see Start and Programmes).
●
The filter has not been cleaned (see Maintenance).
The water container needs emptying? The empty water message is
●
displayed? (see Maintenance).
The heat pump filter needs cleaning? (see Maintenance).
The temperature setting is not ideal for the type of fabric you are drying
●
●
(see Start and Programmes, and see Laundry).
The correct drying time has not been selected for the load (see Laundry).
The air intake grille is obstructed (see Installation, and see Maintenance).
The items were too wet (see Laundry).
●
●
●
●
The dryer was overloaded (see Laundry).
●
Empty water message is
displayed but the dryer has
only been running for a short
period.
The water container was probably not emptied at the start of the
programme. Do not wait for the empty water signal, always check and
empty the container before starting a new drying programme (see
Maintenance).
●
Empty water message is
displayed and the water
container is not full.
This is normal, the:
END OF CYCLE, CLEAN FILTER AND EMPTY THE WATER BOTTLE
message is shown as a reminder to empty the container (see The Display
and Start and Programmes).
Programme finishes and
clothes are damper than
expected.
! For safety the dryer has a maximum programme time of 5 hours. If an
automatic programme has not sensed the required final moisture in this time
the dryer will complete the programme and stop. Check the above points
and run the programme again, if the results are still damp, contact the
Service Centre (see Service).
●
The display shows a fault
code F followed by one or two
numbers.
If the display shows a fault:
- Turn off and remove the plug. Clean the filter and the heat pump filter
unit (see Maintenance). Then replace the plug, turn on and start another
programme. If a fault is then displayed: Note down the
code and contact the Service Centre (see Service).
●
The display briefly shows
The dryer is in ‘Demo’ mode. Press and hold both the On/Off and
DEMO ON every 6 seconds.
Start/Pause buttons for 3 seconds. The display will show DEMO OFF for
3 seconds and then the dryer will resume normal operation.
●
The lights on the dryer control
panel are off although the
dryer is switched on.
The dryer has gone into standby mode to save power. This occurs if you
have had a power cut or leave your dryer either without starting a
programme or after your drying programme has finished.
- Press and hold the On/Off button and the lights will come on.
16
Service
Heat Pump System
Spare Parts
GB
This dryer is a complex machine. Repairing it yourself
or having a non-authorised person try to repair it could
cause harm to one or more persons, could damage
the machine and could invalidate the spare parts
warranty.
This dryer is fitted with a sealed heat pump system to
dry your clothes. To operate, the heat pump contains
fluorinated greenhouse gases (F gases) which are
covered by the Kyoto Protocol. These F gases are
contained in a hermetically sealed unit. This sealed
unit contains 0.29kg of the F gas R134a which acts as
a refrigerant.
Call an authorised technician if you experience problems
while using the machine.
If the sealed unit fails then it must be replaced by a
new sealed unit. Contact your nearest Service Centre
for advice.
●
Please note: it is an offence for an unqualified
person to undertake any servicing or repair work that
involves breaking into the sealed heat pump unit.
●
Note: The gases contained in the sealed system
are not hazardous to health, but if they escape they
will have an impact on global warming.
Before calling the Service Centre:
●
Use the troubleshooting guide to see if you can
solve the problem yourself (see Troubleshooting).
If not, turn off the dryer and call the Service Centre
●
closest to you.
Essential Contact Information
Hotpoint Service - Service You Can Rely On
At Hotpoint we pride ourselves on offering our customers the best service we possibly can, wherever you are in the
UK and Ireland.
Rest assured though, no one knows a Hotpoint appliance better than we do and our service is second to none...
Wherever you are we can be there - we have over 1,000 highly skilled Hotpoint engineers covering the whole of the
UK and Ireland ensuring fast, reliable, local service.
‘Right first time’ - our engineers have the latest tools to help get your Hotpoint appliance back up and running the
first time we visit.
Experts in our field - all of our engineers are trained to the highest standard at our Hotpoint Training Centre of
Excellence with unrivalled expertise and product knowledge.
Skilled staff - we have over 400 skilled UK based call centre staff, dedicated to offering you excellent service 364
days a year.
Telephone in the United Kingdom: 08448 224 224
Telephone in the Republic of Ireland: 0818 313 413
Our advisors will require the following information:
●
●
the appliance model (Mod.).
the serial number (S/N).
●
name, address and post code.
telephone number.
the type of problem.
●
This information can be found on the data label inside
the door of the machine.
●
●
the date of purchase.
Save energy and respect the environment
●
Wring out items to eliminate excess water before tumble drying (if you use a washing machine first, select a high spin
cycle). Doing this will save time and energy during drying.
Always dry full loads - you save energy: single items or small loads take longer to dry.
●
●
Clean the filter after each use to contain energy consumption costs (see Maintenance).
17
Product Data...
(EU Regulation 392/2012)
Brand Hotpoint
Models
TDHP 871
GB
Rated capacity of Cotton laundry for the standard programme at full load 8 kg
The weighted Annual Energy Consumption (AEc) 305.5 kWh
Energy efficiency class A+
Consumption per year, based on 160 drying cycles of the standard cotton programme at full and partial load, and the
consumption of the low-power modes. Actual energy consumption per cycle will depend on how the appliance is used.
This household tumble dryer is an Automatic Condenser Dryer
Energy consumption : full load Edry 2.64 kWh, partial load Edry1/2 1.34 kWh
Power consumption : off-mode (Po) 0.14 W, left-on mode (Pl) 3.16 W
Duration of the ‘left-on mode’ for power management systems 30 minutes
The ‘standard cotton programme’ suitable for drying normal wet cotton laundry that is the most efficient programme in
terms of energy consumption for cotton used at full and partial load is Standard Cotton, High Heat, Cupboard Dry
Programme time (minutes) : weighted (Tt) full & partial load 173, full load (Tdry) 235, partial load (Tdry1/2) 127
Condensation efficiency class C
Average condensation efficiency (%) : full load (Cdry) 72, partial load (Cdry1/2) 71, weighted (Ct) full & partial load 71
Airborne acoustical noise emissions 69 dB(A) re 1 pW
* “consumer information in compliance with EU Regulation 932/2012”.
Typical energy used
Typical drying time
-
-
Synthetics full load 0.69 kWh,
Synthetics full load 70 minutes,
partial load not applicable
partial load not applicable
This data is also available on the website http://www.hotpoint.eu/hotpoint/
Recycling and Disposal Information
As part of our continued commitment to helping
the environment, we reserve the right to use
Disposal of old electrical appliances
The European Directive 2012/19/EC on Waste Electrical
and Electronic Equipment (WEEE), requires that old
household electrical appliances must not be disposed
of in the normal unsorted municipal waste stream. Old
appliances must be collected separately in order to
optimise the recovery and recycling of the materials
they contain and reduce the impact on human health
and the environment.
This dryer has a sealed heat pump unit containing F
gases which should be recovered and distroyed.
The crossed out “wheeled bin” symbol on the
product reminds you of your obligation, that
when you dispose of the appliance it must be
separately collected.
quality recycled components to keep down customer
costs and minimise material wastage.
●
Disposing of the packaging material: follow local
regulations, so the packaging can be recycled.
To minimise risk of injury to children, remove the
●
door and plug - then cut off mains cable, flush
with the appliance. Dispose of these parts separately
to ensure that the appliance can no longer be
plugged into a mains socket.
Consumers should contact their local authority or
retailer for information concerning the correct disposal
of their old appliance.
This appliance conforms to the following EC Directives:
- 2006/95/EC (Low Voltage Equipment)
- 2004/108/EC (Electromagnetic Compatibility)
18
GB
19
195121184. 00 N
01/2014 - LION fpg . Four Ashes, Wolverhampton
GB
20
|