Hotpoint Washer AQ73F49E User Manual

Instructions for

installation and use

WASHING MACHINE

Contents

Installation, 2-3-4-5

Unpacking and levelling

Connecting the electricity and water supplies

Technical data

English,1

Care and maintenance, 6

Cutting off the water and electricity supplies

Cleaning the machine

Cleaning the detergent dispenser drawer

Caring for your appliance drum

Cleaning the pump

Checking the water inlet hose

Precautions and tips, 7

General safety

Load balancing system

Disposal

Opening the porthole door manually

Description of the machine, 8-9

Control panel

AQUALTIS

Running a wash cycle, 10

AQ73F 49 E

Wash cycles and options, 11

Table of wash cycles

Wash options

Detergents and laundry, 12

Detergent

Preparing the laundry

Washing recommendations

Trouble shooting, 13-14

Assistance, 15-16

Connecting the drain hose

• the socket is compatible with the washing

machine’s plug. If this is not the case, replace

the socket or the plug.

Connect the drain

hose, without

bending it, to a

Your appliance is now supplied with a 13 amp

fused plug it can be plugged into a 13 amp

socket for immediate use. Before using the

appliance please read the instructions below.

draining duct or a

wall drain situated

between 65 and 100

cm from the floor;

65 - 100 cm

WARNING - THIS APPLIANCE MUST BE

EARTHED.

THE FOLLOWING OPERATIONS SHOULD

BE CARRIED OUT BY A QUALIFIED

ELECTRICIAN.

The drain hose may

be connected to

an under-sink trap.

Before connecting

the drain hose from

the machine ensure

that any blanks or

removable ends

Replacing the fuse:

When replacing a faulty fuse, a 13 amp ASTA

approved fuse to BS 1362 should always be

used, and the fuse cover re-fitted. If the fuse

cover is lost, the plug must not be used until a

replacement is obtained.

Where it connects to

the waste water pipe

cut end off spigot or

remove the blanking cap

have been taken off

the spigot.

Replacement fuse covers:

If a replacement fuse cover is fitted, it must

be of the correct colour as indicated by

the coloured marking or the colour that is

embossed in words on the base of the plug.

Replacements can be obtained directly from

your nearest Service Depot.

If it is placed over

the edge of a basin

or sink be sure

the free end of the

hose should not be

underwater.

Removing the plug:

If your appliance has a non-rewireable

moulded plug and you should wish to re-route

the mains cable through partitions, units etc.,

please ensure that either:

! We advise against the use of hose extensions;

in case of absolute need, the extension must

have the same diameter as the original hose

and must not exceed 150 cm in length.

Ensure that if the drain hose is pushed into a

standpipe, that the end does not go down more

than 15cms (6 inches). If the hose is pushed

down too far, this may cause the machine to self

-syphon ie. continuously empty as it is filling.

the plug is replaced by a fused 13 ampere

rewireable plug bearing the BSI mark of approval.

or:

the mains cable is wired directly into a 13

amp cable outlet, controlled by a switch, (in

compliance with BS 5733) which is accessible

without moving the appliance.

Disposing of the plug:

Ensure that before disposing of the plug itself,

you make the pins unusable so that it cannot

be accidentally inserted into a socket.

Electric connection

Before plugging the appliance into the mains

socket, make sure that:

• the socket is earthed and in compliance

with the applicable law;

Instructions for connecting cable to an

alternative plug:

• the socket is able to sustain the appliance’s

maximum power load indicated on the

Technical Data Plate fixed on the machine.

• the supply voltage is included within the

values indicated on the Technical Data

Plate fixed on the machine.

Important: the wires in the mains lead are

coloured in accordance with the following code:

Green & Yellow

Blue

Brown

Earth

Neutral

Live

As the colours of the wires in the lead may

not correspond with the coloured markings

identifying the terminals in your plug, proceed

as follows:

! The power supply cable must only be

replaced by an authorised serviceman.

Warning! The company denies all liability if and

when these norms are not respected.

Connect Green & Yellow wire to terminal

marked E or or coloured Green or Green &

Yellow.

Connect Brown wire to terminal marked L or

coloured Red.

Connect Blue wire to terminal marked N or

coloured Black.

If a 13 amp plug (BS 1363) is used it must be

fitted with a

13 amp fuse, either in the plug or adaptor or

at the distribution board.

If you are in any doubt regarding the electrical

supply to your machine, consult a qualified

electrician before use.

How to connect an alternative plug:

The wires in this mains lead are coloured in

accordance with the following code:

BLUE

NEUTRAL (N)

LIVE (L)

EARTH (E)

BROWN

GREEN & YELLOW

GREEN &

YELLOW

13 ampere fuse

BROWN

CROSS-BAR

CORD GRIP

BLUE

Disposing of the appliance:

When disposing of the appliance please

remove the plug by cutting the mains cable

as close as possible to the plug body and

dispose of it as described on the previous

page.

! The washing machine should not be installed

in an outdoor environment, not even where

the area is sheltered, because it may be very

dangerous to leave it exposed to damp, rain

and thunderstorms.

! When the washing machine is installed, the

mains socket must be within easy reach.

! Do not use extensions or multiple sockets.

! The power supply cable must never be bent

or dangerously compressed.

Technical data

Model

AQ73F 49 E

width 59.5 cm

Dimensions height 85 cm

depth 58 cm

Capacity

Electrical

from 1 to 7 kg

please refer to the technical

connections data plate fixed to the machine

maximum pressure

1 MPa (10 bar)

Water con-

minimum pressure

nections

0.05 MPa (0.5 bar)

drum capacity 58 litres

up to 1400 rotations per

minute

Spin speed

Test wash

cycles in

accordan-

ce with

programme

;

Cotton Standard 60°C.

directives

1061/2010

and

programme

Cotton Standard 40°C.

;

1015/2010

This appliance conforms to

the following EC Directives:

- 2004/108/EC (Electroma-

gnetic Compatibility)

- 2006/95/EC (Low Voltage)

- 2012/19/EU

Care and maintenance

To access the pre-chamber:

Cutting off the water and

electricity supplies

• Turn off the water tap after every wash cycle.

This will limit wear on the hydraulic system in

the machine and help to prevent leaks.

• Unplug the appliance when cleaning it and

during all maintenance work.

Cleaning the machine

1. take off the cover panel on the front of the

machine by first pressing it in the centre and

then pushing downwards on both sides until

you can remove it (see figures);

The outer parts and rubber components of the

appliance can be cleaned using a soft cloth

soaked in lukewarm soapy water. Do not use

solvents or abrasives.

2. position a container

so that it will collect the

water which flows out

(approximately 1.5 l)

(see figure);

3. unscrew the lid by

rotating it in an anti-

clockwise direction (see

figure);

Cleaning the detergent dispenser

drawer

To remove the drawer,

press lever (1) and pull

the drawer outwards (2)

(see figure).

Wash it under running

water; this procedure

4. clean the inside thoroughly;

5. screw the lid back on;

6. reposition the panel, making sure the hooks

are securely in place before you push it onto

the appliance.

should be repeated

frequently.

Caring for your appliance drum

Checking the water inlet hose

• Always leave the door ajar to prevent

unpleasant odours from forming.

Check the inlet hose at least once a year. If

there are any cracks, it should be replaced

immediately: during the wash cycles, water

pressure is very strong and a cracked hose

could easily split open.

Cleaning the pump

The washing machine is fitted with a self-

cleaning pump which does not require any

maintenance. Sometimes, small items (such

as coins or buttons) may fall into the protective

pre-chamber at the base of the pump.

! Make sure the wash cycle has finished and

unplug the appliance.

Precautions and tips

! The machine was designed and constructed in

accordance with international safety regulations. The

following information is provided for safety reasons and

must therefore be read carefully.

inside the machine, while preventing potential damage

to the atmosphere and to public health.

The crossed-out dustbin is marked on all products

to remind the owner of their obligations regarding

separated waste collection.

General safety

For more information relating to the correct disposal of

household appliances, owners should contact their local

authorities or appliance dealer.

^•• T^Th^hi^iss^aa^pp^pp^lialⁿia^cn^ec^we^asc^da^en^sib^gne^edus^foe^rd^dob^my^esc^th^icil^ud^sr^een^only.

aged from 8 years and above and

persons with reduced physical, sensory or

mental capabilities or lack of experience

and knowledge if they have been given

supervision or instruction concerning use of

the appliance in a safe way and understand

the hazards involved. Children shall not

play with the appliance. Cleaning and user

maintenance shall not be made by children

without supervision.

Opening the porthole door manually

In the event that it is not possible to open the porthole door

due to a powercut, and if you wish to remove the laundry,

proceed as follows:

1. remove the plug from the

electrical socket.

2. make sure the water level

inside the machine is lower

than the door opening; if

it is not, remove excess

water using the drain hose,

collecting it in a bucket as

indicated in the figure.

• Do not touch the machine when barefoot or with wet or

damp hands or feet.

• Do not pull on the power supply cable when unplugging

the appliance from the electricity socket. Hold the plug

and pull.

• Do not touch the drained water as it may reach

extremely high temperatures.

• Never force the porthole door. This could damage the

safety lock mechanism designed to prevent accidental

opening.

3. remove the cover panel on the lower front part of the

washing machine (see overleaf).

• If the appliance breaks down, do not under any

circumstances access the internal mechanisms in an

attempt to repair it yourself.

• Always keep children well away from the appliance while

it is operating.

• If it must be moved, proceed with the help of two or

three people and handle it with the utmost care. Never

try to do this alone, because the appliance is very heavy.

• Before loading laundry into the washing machine, make

sure the drum is empty.

4. pull outwards using the

tab as indicated in the figure,

until the plastic tie-rod is freed

from its stop position; pull

downwards until you hear a

“click”, which indicates that

the door is now unlocked.

Load balancing system

Before every spin cycle, to avoid excessive vibrations

before every spin and to distribute the load in a uniform

manner, the drum rotates continuously at a speed which

is slightly greater than the washing rotation speed. If,

after several attempts, the load is not balanced correctly,

the machine spins at a reduced spin speed. If the load is

excessively unbalanced, the washing machine performs

the distribution process instead of spinning. To encourage

improved load distribution and balance, we recommend

small and large garments are mixed in the load.

5. open the door; if this is

still not possible repeat the

procedure.

Disposal

6. reposition the panel, making sure the hooks are securely

in place before you push it onto the appliance.

• Disposing of the packaging materials: observe local

regulations so that the packaging may be re-used.

• The European Directive 2012/19/EU relating to Waste

Electrical and Electronic Equipment (WEEE) states

that household appliances should not be disposed of

using the normal solid urban waste cycle. Exhausted

appliances should be collected separately in order to

optimise the cost of re-using and recycling the materials

Description of the machine

CONTROL

PANEL

PORTHOLE DOOR

HANDLE

KICK STRIP

ADJUSTABLE FEET

PORTHOLE DOOR

! Do not pour detergent into

the compartment 1.

Detergent should only be

poured into the compartment 2.

Always use the handle to

open the porthole door (see

figure).

2. main wash compartment:

If liquid detergent is used,

it is recommended that the

removable plastic partition A

(supplied) be used for proper

dosage.If powder detergent is

used, place the partition into slot B.

washing additives compartment: for fabric softener

or liquid additives. We recommend that the maximum

level indicated by the grille is not exceeded, and that

concentrated fabric softeners are diluted.

DETERGENT DISPENSER DRAWER

The detergent dispenser

drawer is located inside

the machine and can be

accessed by opening the

door.

For more information on

detergent measures, please

refer to the chapter entitled

“Detergents and laundry”.

Standby mode

This washing machine, in compliance with new energy

saving regulations, is fitted with an automatic standby

system which is enabled after about 30 minutes if no

activity is detected. Press the ON-OFF

wait for the machine to start up again.

Consumption in off-mode: 0,5 W

Consumption in Left-on: 0,5 W

button briefly and

Control panel

WASH

CYCLE

PHASE

icons

ECO

indicator light

START/

PAUSE

button with

OPTION buttons

with indicator lights

OPTION buttons

with indicator lights

WASH CYCLE

SELECTOR knob

indicator light

DISPLAY

TEMPERATURE

DELAY TIMER

button

CHILD LOCK button

with indicator light

Button with ON/OFF

indicator light

button

SPIN

LOCK indicator light

button

START/PAUSE button with indicator light: when the green

indicator light flashes slowly, press the button to start a

wash cycle. Once the cycle has begun the indicator light

will remain lit in a fixed manner. To pause the wash cycle,

press the button again; the indicator light will flash in an

orange colour. If the “LOCK” indicator light is switched

off, the door may be opened. To start the wash cycle from

the point at which it was interrupted, press the button

again.

Button with

ON/OFF indicator light: press this briefly

to switch the machine on or off. The green indicator light

indicates that the machine is switched on. To switch off the

washing machine during the wash cycle, press and hold

the button for approximately 3 seconds; if the button is

pressed briefly or accidentally the machine will not switch

off. If the machine is switched off during a wash cycle, this

wash cycle will be cancelled.

WASH CYCLE SELECTOR knob: may be turned in

either direction. To select the most suitable wash cycle,

please refer to the “Table of wash cycles”.

LOCK indicator light: indicates that the porthole door

is locked. To open the door, pause the wash cycle (see

“Running a wash cycle”).

The knob will not move during the wash cycle.

CHILD LOCK

button with indicator light: to activate

TEMPERATURE

button: press to modify or exclude

or deactivate the CHILD LOCK, press and hold the button

for approximately 2 seconds. when the indicator light is

illuminated, the control panel is locked (apart from the

ON/OFF button). This means it is possible to prevent wash

cycles from being modified accidentally, especially where

there are children in the home.

the temperature setting; the value selected will appear on

the display above (see “Running a wash cycle”).

SPIN CYCLE

button: press to modify or exclude the

spin cycle; the value selected will appear on the display

above (see “Running a wash cycle”).

DELAY TIMER

for the selected wash cycle; the set delay time will appear

on the display above (see “Running a wash cycle”).

button: press to set a DELAY TIMER

ECO indicator light: the

icon lights up when, after

altering the washing parameters, an energy saving of

at least 10% is made. Furthermore, before the machine

enters “Standby” mode, the icon will light up for a few

seconds; when the machine is switched off the estimated

energy saving will be around the 80% mark.

OPTION buttons with indicator lights: press to select the

available options. The indicator light corresponding to the

selected option will remain lit (see “Running a wash cycle”).

WASH CYCLE PHASE icons: these illuminate to indicate the

progress of the wash cycle (Wash

– Rinse

– Spin

–

Drain ). The text lights up when the cycle is complete.

Running a wash cycle

WARNING: before you use the washing machine for the

first time, run a wash cycle with detergent and no laundry,

using the 90° cottons cycle.

Modify the cycle settings.

Press the OPTION buttons to customise the wash cycle

in accordance with your own requirements.

• Press the button to activate the option; the

corresponding indicator light will switch on.

• Press the button again to disable the option; the

indicator light will switch off.

! If the selected option is not compatible with the

selected wash cycle, this incompatibility will be signalled

by the flashing of the indicator light and a sound alert

(3 beeps); the option will not be activated.

! If the selected option is not compatible with another

option that has been selected previously, the indicator

light corresponding to the first option selected will

flash and only the second option will be activated; the

indicator light corresponding to the button will remain lit

in a constant manner.

1. SWITCH THE MACHINE ON. Press the

button.

All the indicator lights will illuminate for 1 second; the

indicator light corresponding to the button will then

remain lit in a fixed manner and the START/PAUSE

indicator light will flash slowly.

2. LOAD THE LAUNDRY. Open the porthole door.

Load the laundry, making sure you do not exceed the

maximum load value indicated in the table of wash

cycles on the following page.

3. MEASURE OUT THE DETERGENT. Pull out the

detergent dispenser drawer and pour the detergent into

the relevant compartments as described in “Description

of the machine”.

7. START THE PROGRAMME. Press the START/PAUSE

button. The corresponding indicator light remains lit in a

fixed manner and the porthole door locks (the LOCK

indicator light illuminates). The icons corresponding to

the wash cycle phases will light up during the cycle to

indicate which phase is currently in progress.

4. CLOSE THE PORTHOLE DOOR.

5. SELECT THE PROGRAMME. Turn the WASH CYCLE

SELECTOR KNOB right or left, until you have selected

the desired wash cycle. A temperature and spin speed

is set for each wash cycle; these may be adjusted.

To change a wash cycle once it has already started,

pause the washing machine by pressing the START/

PAUSE button; then select the desired cycle and press

the START/PAUSE button again.

6. CUSTOMISE THE WASH CYCLE. Use the relevant

buttons on the control panel:

To open the door during a wash cycle, press the START/

PAUSE button; if the LOCK indicator light is switched

off you may open the door. Press the START/PAUSE

button again to restart the wash cycle from the point at

which it was interrupted.

Modify the temperature and/or spin

speed.

The machine automatically displays the maximum

temperature and spin speed values set for the selected

cycle, or the most recently-used settings if they are

compatible with the selected cycle. The temperature

8. THE END OF THE WASH CYCLE. This is indicated

by the illuminated text END. The porthole door may be

opened immediately. If the START/PAUSE indicator light

is flashing, press the button to end the cycle. Open the

door, unload the laundry and switch off the machine.

can be decreased by pressing the

cold wash ( ) setting is reached. The spin speed may

be progressively reduced by pressing the button,

until it is completely excluded ( ). If these buttons are

pressed again, the maximum values are restored.

programme is selected, the

button, until the

! If you wish to cancel a cycle which has already begun,

! Exception: if the

press and hold the

button until the cycle stops and the

temperature can be increased up to a value of 90°C.

machine switches off.

Setting a delayed start.

Press the button until you have reached the desired

delay time. During the setting process, the delay time is

Bag for quilts, curtains and delicate garments

The Aqualtis washing machine makes it easier for you

to wash even the most valuable and delicate garments

in complete confidence thanks to the special bag which

protects the laundry (this is supplied with the machine).

We recommend that the bag is used every time you wash

quilts and padded items with an outer layer made

using synthetic material.

shown on the display and the

symbol flashes.

After selecting a DELAYED START time, the fixed

symbol and the cycle duration will appear on the display.

Press the button once to display the selected delay

time.

To remove the DELAY TIMER option, press the button

until the display shows the text OFF; the

disappear.

symbol will

! Once the START/PAUSE button has been pressed, the

time delay may only be decreased.

Wash cycles and options

Table of wash cycles

Detergent

and additives

Max.

speed

(rpm)

Max.

temp. (°C)

Description of the wash cycle

Synthetics

60°

40°

60°

40°

30°

40°

30°

60°

800



4.5 45 1.16 65 120’

4.5 45 0.74 64 100’

Synthetics (3)

Whites

1400

800

200’

110’

80’

Coloureds

Darks

Shirts

600

75’

Duvets: for down-stuffed garments.

Bed & Bath for bedlinen and towels.

1200

1400

3.5

105’

140’

Rinse

1400



49’

16’

Spin and Pump out

Anti Allergy

60°

30°

40°

1400



200’

75’

Ultra Delicates

Wool: for wool, cashmere, etc.

800

105’

Mix 30': to refresh lightly soiled garments quickly (not suitable for wool,

silk and clothes which require washing by hand).

30°

800



3.5 70 0.11 41

30’

60°

(Max. 90°)

Cotton Standard 60°C (1): heavily soiled whites and resistant colours.

1400

53 0.92 50 175’

53 0.90 67 160’

Cotton Standard 40°C (2): lightly soiled whites and delicate colours.

Cotton Standard 20°C: lightly soiled whites and delicate colours.

40°

1400



20°

180’

The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary accor-

ding to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.

Note: 10 minutes after the START, the machine will recalculate the time remaining until the end of the wash cycle on the basis of the load inside it; this value

will then be shown on the display.

1) Test wash cycle in compliance with directive 1061/2010: set wash cycle

with a temperature of 60°C.

This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for

garments which can be washed at 60°C. The actual washing temperature may differ from the indicated value.

2) Test wash cycle in compliance with directive 1061/2010: set wash cycle

with a temperature of 40°C.

This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for

garments which can be washed at 40°C. The actual washing temperature may differ from the indicated value.

For all Test Institutes:

2) Long wash cycle for cottons: set wash cycle

with a temperature of 40°C.

3) Long wash cycle for synthetics: set wash cycle with a temperature of 40°C.

Wash options

Eco

Extra Rinse

The Eco Option saves energy by not heating the water

used to wash your laundry – an advantage both to the

environment and to your energy bill. Instead, intensified

wash action and water optimisation ensure great wash

results in the same average time of a standard cycle.

For the best washing results we recommend the usage of a

liquid detergent.

By selecting this option, the efficiency of the rinse is

increased and optimal residual detergent removal is

guaranteed. It is particularly useful for skin which is

sensitive to detergents. We recommend this option is used

with a full load of washing, or when a large amount of

detergent is required.

! It cannot be used in conjunction with

Easy Iron

By selecting this option, the wash and spin cycles will be

modified in order to reduce the formation of creases.

At the end of the cycle the washing machine drum will

rotate slowly; the “Easy Iron” and START/PAUSE indicator

lights will flash. To end the cycle press the START/PAUSE

button or the “Easy Iron” button.

Time Saver

If you select this option, the wash cycle duration will be

reduced by up to 50%, depending on the selected cycle,

thereby guaranteeing simultaneous water and energy

saving. Use this cycle for lightly soiled garments.

! It cannot be used in conjunction with

Detergents and laundry

Duvets: to wash double or single duvets (the weight of which

should not exceed 3,5 kg), cushions or clothes padded with

goose down such as puffa jackets, use the special wash

cycle. We recommend that duvets are placed in the drum with

their edges folded inwards (see figure) and that no more than

¾ of the total volume of the drum is used. To achieve the best

results, we recommend that a liquid detergent is used and

placed inside the detergent dispenser drawer.

Detergent

The type and quantity of detergent required depend on the

type of fabric you are washing (cotton, wool, silk, etc.), as well

as its colour, the washing temperature, the level of soiling and

the hardness of the water in the area.

Measuring out the detergent carefully will avoid wastage

and help to protect the environment: although they are

biodegradable, detergents still contain ingredients which alter

the balance of nature.

We recommend the following:

• use powder detergents for white cotton garments and pre-

washing.

• use liquid detergents for delicate cotton garments and for

all low-temperature wash cycles.

• use gentle liquid detergents for wool and silk garments.

The detergent should be poured into the relevant compartment

- or the dispenser placed directly inside the drum - before the

wash cycle begins. In the latter case, it will not be possible to

select the Cottons with pre-wash cycle.

! Do not use hand washing detergents because these create

too much foam.

! Use powder detergent for white cotton garments, for pre-

washing, and for washing at temperatures over 60°C.

! Follow the instructions given on the detergent packaging.

Quilts: to wash quilts with a synthetic outer layer, use the bag

provided and set the wash cycle to

Bed & Bath: Use programme

to wash bed linen and

towels in one single cycle: it optimises softener performance

and helps you save time and energy. We recommend the use

of powder detergent

Anti Allergy:use programme to remove major allergens such

as pollen, mites, cat’s and dog’s hair.

Preparing the laundry

• Shake out the garments before loading them into the

machine.

• Divide the laundry according fabric type (symbol on the

washing instruction label) and colour, making sure you

separate the coloured garments from the white ones;

• Empty all pockets and check the buttons;

• Do not exceed the values listed in the “Table of wash

cycles”, which refer to the weight of the laundry when dry.

Ultra Delicates: use programme

to wash very delicate

garments with decorative features, such as diamantes and

sequins. We recommend turning the garments inside out

before washing and placing small items into the special

bag for washing delicates. Use liquid detergent on delicate

garments for best results.

To wash Silk garments and Curtains (these should be folded

and placed inside the bag provided), select cycle

option (in this case it will also be possible to enable

the “Extra Rinse” option); the machine will end the cycle

while the laundry is soaking and the indicator light will

flash. To drain the water so that the laundry may be removed,

press the START/PAUSE button or the button.

and then

How much does your laundry weigh?

1 sheet

400-500 g

150-200 g

400-500 g

900-1200 g

150-250 g

400-500 g

150-200 g

1 pillowcase

1 tablecloth

1 bathrobe

1 towel

1 pair of jeans

1 shirt

Wool: the wool wash cycle on this Hotpoint machine has

been tested and approved by The Woolmark Company for

washing wool garments labelled as hand washable provided

that the garments are washed according to the instructions on

the garment label and those issued by the manufacturer of this

washing machine. Hotpoint is the first washing machine brand

to be approved by The Woolmark Company for Apparel

Care- Platinum for its washing performance and consumption

of energy and water.

Washing recommendations

Whites: use this cycle

to wash white clothes. The

programme is designed to maintain the brightness of white

clothes over time.

Coloureds: use this cycle

to wash bright coloured

clothes. The programme is designed to maintain bright colours

over time.

Darks: Use cycle

to wash dark-coloured garments. This

Cotton Standard 20°: ideal for heavily soiled cotton

loads. The effective performance levels achieved at cold

temperatures, which are comparable to washing at 40°, are

guaranteed by a mechanical action which operates at varying

speed, with repeated and frequent peaks.

programme is designed to maintain dark colours over time.

We recommend using a liquid detergent for the best results

when washing dark-coloured garments.

Shirts: use the special

different fabrics and colours to guarantee they receive the

best possible care.

wash cycle to wash shirts in

Trouble shooting

Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Centre (see “Assistance”),

make sure that the problem cannot be solved easily using the following list.

Problem:

The machine does not switch on.

Possible causes / Solutions:

• The appliance is not plugged into the socket fully, or not enough to make contact.

• There is no power to the socket, or the fuse has blown in the mains plug.

The wash cycle does not start.

• The door is not closed properly.

• The ON/OFF button has not been pressed.

• The START/PAUSE button has not been pressed.

• The water tap has not been turned on to allow water to flow into the machine.

• The ‘DELAY TIMER’ has been selected.

• The ‘CHILD LOCK’ is activated (see ‘The machine just ‘beeps’ when a

programme or option is selected’ below).

The machine does not fill with

• The water inlet hose is kinked.

water or Indicator light for the first • The water inlet hose is not connected to the water supply.

wash cycle flashing rapidly.

• The water pressure is too low.

• The water tap has not been turned on to allow water to flow into the machine.

• There is no water supply to the house.

• The inlet valve filter is blocked.

• The START/PAUSE button has not been pressed.

The machine continuously fills with • The top of the drain hose is too low - It must be fitted at a height between 65

water and continually drains away

or Water left in the drum

or Stuck on wash.

and 100 cm from the floor (see “Installation”).

• The drain hose is connected incorrectly to the sink trap allowing water to run

into the machine, the drain hose must be positioned higher than the bottom of

the sink to prevent water flowing down the drain hose.

• The end of the drain hose has been pushed too far down the standpipe, the

‘U’ bracket should be fitted 100 mm from the end of the drain hose.

The machine does not drain or spin • The Pump filter is blocked.

- (error lights flashing).

• The drain hose is kinked (see “Installation”).

• New Installation - The blanking cap or spigot has not been removed if

connected under a sink.

• The drain hose or sink trap is blocked.

The machine does not spin.

• The Spin Speed is set to “

” position.

The machine does not drain or spin • The ‘EASY IRON’ option is enabled at the end of the program the machine

- ‘EASY IRON’ light flashes.

drum will rotate slowly. To complete the wash cycle press the ‘START/PAUSE’

or the ‘EASY IRON’ buttons (see Wash Cycles & Options).

• The ‘SILK’ program is selected, at the end of the program it requires the drain

phase to be started. To complete the program press either the ‘START/PAUSE’

or ‘EASY IRON’ buttons (see Wash Cycles & Options).

The programme takes too long.

• Programme times will vary due to water pressure, the incoming water

temperature and if the wash load goes out of balance. This will increase the

programme time accordingly (see ‘The machine wont spin properly’ below)

- (Most Common Cause!)

The Display sticks at one ‘time to

end’ for more than 1 Minute or the

Display changes the estimated ‘Time

to End’ during the programme.

• The display time is for guidance only - it is not a precise time to finish and

may vary.

The machine vibrates a lot during

the spin cycle.

• The feet have not been adjusted, enabling the machine to rock.

• New Installation - Either the Transit Bolts including the plastic spacers, or the

Polystyrene Packaging have not been removed when installing the machine.

• The machine is trapped between cabinets and/or walls.

• The load is in a slight out of balance condition and machine is spinning, but at

a lower speed.

• There will always be some motor, pump and drum noise during spin.

The machine is noisy.

The machine wont spin properly.

• Out of Balance detected when attempting to go into a spin cycle - If this

happens the machine will continue to try to repeat the distribution of the load

required before the machine will go into higher spin speeds - This will increase

the programme time accordingly. This is a safety feature to prevent damage.

Out of Balance can be caused by washing a single heavy item (eg duvet, quilt,

etc). - Try the programme again using a different load.

The machine leaks from the

dispenser.

• The dispenser drawer is blocked with detergent and requires cleaning.

• The water pressure is too high and requires turning down - turn down the tap

on the water supply pipe slightly and try again.

• The machine is tilting forwards - It must be level when in its final position.

The machine leaks (other than

dispenser).

• The fill hose is loose, check both the cabinet and tap ends.

• The fill hose is tight but still leaks, if so replace the rubber washers, or the fill

hose is missing the rubber washer.

• The drain hose is not fixed in properly.

The Phase in Progress indicator

lights flash rapidly at the same

time as the ON/OFF indicator light.

• Switch off the machine and unplug it, wait for approximately 1 minute and then

switch back on again. If the problem persists contact Technical Assistance

Centre.

The machine smells.

• The machine requires a service wash. Run a 60 degree wash cycle with

detergent and no laundry.

The machine door cannot be

opened.

• The door will not open until the door lock indicator light goes out shortly after

the program has finished.

• If there is no power to the machine you need to perform the manual unlocking

procedure (see Precautions & Tips).

Door Seal damaged at the bottom.

• The door seal has drainage holes at the bottom - This is normal.

• The water level is correct if it can be seen at the bottom of the door.

The water level is too low when

the machine is washing.

The word ‘dON’ appears

intermittently in the display

window and the drum slowly turns.

• To exit, switch machine off, then press and hold ‘START/PAUSE’ and ‘ON/OFF’

buttons simultaneously for 3 seconds.

The machine just ‘beeps’ when a

programme or option is selected

(Child Lock Symbol is lit).

• Deactivate the Child Lock feature by pressing and holding in the ‘CHILD

LOCK’ button for 2 seconds.

There is too much foam.

• The detergent is not suitable for machine washing (it should display the text

‘for washing machines’ or ‘hand and machine wash’ or the like).

• Too much detergent was used - less detergent is required in soft water.

After completing the programme,

or before starting a programme,

the machine has turned itself off

(no lights).

• To comply with new energy saving regulations the machine is fitted with an

automatic standby system. Press ‘ON/OFF’ button for 3 seconds to activate

the machine, it can then either be switched off or a new programme selected.

General.

• Your washing machine contains sensors that monitor progress during the wash

cycle (eg: Water Levels, Temperatures, Out of Balance loads, Wash time/progress).

Normally, if your machine successfully completes the cycle, there is unlikely to

be anything wrong!

Remember, you will be charged for a service call for problems caused by incorrect installation, as listed above.

Not emptying contents from pockets may cause pump or drain blockages, or may damage the machine.

Do not wash items which do not have a wash label, or wash items that are not intended as machine washable.

Assistance

Guarantee

12 Months Parts and Labour Guarantee

Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of breakdown

repairs for twelve months from the date of purchase.

This gives you the reassurance that if, within that time, your appliance is proven to be defective because of

either workmanship or materials, we will, at our discretion, either repair or replace the appliance at no cost

to you.

This guarantee is subject to the following conditions:

The appliance has been installed and operated correctly and in accordance with our

operating and maintenance instructions.

The appliance is used only on the electricity or gas supply printed on the rating plate.

The appliance has been used for normal domestic purposes only.

The appliance has not been altered, serviced, maintained, dismantled, or otherwise

interfered with by any person not authorised by us.

Any repair work must be undertaken by us or our appointed agent.

Any parts removed during repair work or any appliance that is replaced become our property.

The appliance is used in the United Kingdom or Republic of Ireland.

The guarantee does not cover:

Damage resulting from transportation, improper use, neglect or interference or as a result

of improper installation.

Replacement of any consumable item or accessory . These include but are not limited to: plugs,

cables, batteries, light bulbs, fluorescent tubes and starters, covers and filters.

Replacement of any removable parts made of glass or plastic.

THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL

OR NON-DOMESTIC PREMISES.

5 Year Parts Guarantee

Hotpoint also offers you a free 5 year parts guarantee. This additional guarantee is conditional on you

registering your appliance with us and the parts being fitted by one of our authorised engineers. There will

be a charge for our engineer’s time. To activate the extra parts warranty on your appliance, simply call our

registration line on 08448 24 24 24 (ROI 01 230 0800).

Extended Guarantees

We offer a selection of repair protection plans that enable you to fully cover yourself against the expense of repair

bills for the life of your policy. To find the ideal plan for you please call our advice line on

08448 226 226 (Republic of Ireland 01 230 0233).

Free Helpdesk Service

We have a dedicated team who can provide free advice and assistance with your appliance if you

experience any technical difficulties within the first 90 days of ownership. Simply call our Hotpoint Service

Hotline on 08448 224 224 (Republic of Ireland 0818 313 413) for telephone assistance, or, where

necessary, to arrange for an engineer to call. If we cannot resolve the technical problem we will replace

your machine or, if you prefer, give you your money back.

195110685.00

01/2013

Xerox Fabriano

After Sales Service

No one is better placed to care for your Hotpoint appliance during the course of its working

life than us - the manufacturer.

Essential Contact Information

Hotpoint Service

We are the largest service team in Europe offering you access to 400 skilled telephone advisors and 1000

fully qualified engineers on call to ensure you receive fast, reliable, local service.

UK: 08448 224 224

Republic of Ireland: 0818 313 413

www.hotpointservice.co.uk

Please note: Our advisors will require the following information:

Model number:

Serial number:

Parts and Accessories

We supply a full range of genuine replacement parts as well as accessory products that protect and

hygienically clean your appliance to keep it looking good and functioning efficiently throughout its life.

UK: 08448 225 225

Republic of Ireland: 0818 313 413

www.hotpointservice.co.uk

Appliance Registration

We want to give you additional benefits of Hotpoint ownership. To activate your free 5 year parts guarantee

you must register your appliance with us.

UK: 08448 24 24 24

Republic of Ireland: 01 230 0800

www.hotpointservice.co.uk

Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB

Indesit Company Unit 49 Airways Industrial Estate,Dublin 17

Recycling & Disposal Information

As part of Hotpoint’s continued commitment to helping the environment, Hotpoint reserves the right to use

quality, recycled components to keep down customer costs and minimise material wastage.

Please dispose of packaging and old appliances carefully. To minimise the risk of injury to children, remove

the door, plug and cut the mains cable off flush with the appliance. Dispose of these parts separately to

ensure that the appliance can no longer be plugged into a mains socket, and the door

Grandstream Networks Security Camera GXV3504 User Manual
Haier Clothes Dryer HDY D70 F User Manual
Haier Washer Dryer HW70 1282 User Manual
Hamilton Beach Slow Cooker 33041 User Manual
Hamilton Watch Watch ETA 251272 User Manual
Harbor Freight Tools Power Hammer 97626 User Manual
Harman Speaker MS 10SD2 User Manual
Healthrider Treadmill 831297872 User Manual
HP Hewlett Packard Home Theater System 2000495 User Manual
Hypertec Carrying Case 6102HY User Manual