IBM Network Card 9000s User Manual

[ Quick Start Guide ]  
F I B R E C H A N N E L S W I T C H I N S T A L L A T I O N  
z
®
S AN b o x 9 0 0 0 S e r i e s  
®
f o r W i n d o w s O p er a t i n g S y s t e m s  
 
Quick Start Guide  
Installation Instructions  
®
Congratulations on your purchase of the SANbox 9000 Series Fibre Channel Switch. This guide describes the steps to  
install and activate your new switch using a Windows® workstation. For advanced options and instructions (including  
®
®
®
Solaris , Linux , and Mac OS X installations), refer to the SANbox 9000 Series Stackable Chassis Switch Installation  
Guide on the product CD.  
NOTE:  
Do not apply power to the switch until instructed in Step 4.  
Step 1. Verify the Package Contents  
The SANbox 9000 Series Fibre Channel Switch is shipped with the following items:  
1
2
1
1
1
SANbox 9000 Series Fibre Channel Switch  
AC Power cords  
Rail kit  
RJ-45/RS-232 console adapter  
Enterprise Fabric Suite 2007 CD  
NOTE:  
Transceivers and stacking cables, if you ordered them, are packaged separately.  
Step 2. Mount the Switch  
WARNING!! Two people are required to safely lift and install the switch into a rack. To avoid personal injury or damage  
to the switch, arrange for assistance.  
You can mount the SANbox 9000 Series switch on a flat surface or in a rack. Allow minimum clearances of 2 inches in  
front and 8 inches in the rear for cabling.  
For a rack mount, install the SANbox 9000 Series rail kit in a standard 19" rack as described in the SANbox 9000  
Series Stackable Chassis Switch Rack Mounting Guide that is packaged with the switch.  
Step 3. Install Transceivers  
An SFP transceiver is required for each switch port that will be connected to a device.  
To install an SFP transceiver, insert the transceiver into the switch port and gently press until it snaps in place. The  
transceiver will fit only one way. If the transceiver does not install under gentle pressure, flip it over and try again.  
3
 
Step 4. Apply Power to the Switch  
The maximum current requirements are 10 amps at 100 VAC or 4.2 amps at 240 VAC.  
AttachtheACpowercordstothePowerSupplyblades  
and wall outlets or power strips. Secure the strain  
relief bales to the plugs. Place the On/Off switches in  
the On position.  
CHASSIS  
FAULT LED  
CHASSIS  
GOOD LED  
The switch runs its self tests and begins normal  
operation – this may take a few minutes. Observe the  
Maintenance Panel and verify that the CPU0 blade  
Heartbeat LED is blinking about once per second and  
the Chassis Fault LED is NOT illuminated.  
CPU0  
HEARTBEAT  
LED  
Step 5. Verify Workstation Requirements  
Verify that your workstation can support the Enterprise Fabric Suite 2007™ application with the following minimum  
requirements:  
Windows® 2003 SP1/SP2/R2 and XP  
256 MB memory minimum; 512 MB recommended  
150 MB disk space  
1 GHz processor  
Video card with 256 colors  
CD ROM drive, RJ-45 Ethernet port  
®
®
®
®
Internet Browser: Microsoft Internet Explorer 5.0, Netscape Navigator 6.0, Firefox 1.0, or Mozilla™ 1.5  
®
Java 2 Standard Edition Runtime Environment 1.4.2  
The default IP address of a new switch is 10.0.0.1. Ensure that your workstation is configured to communicate  
with the 10.0.0 subnet.  
4
 
 
Step 6. Connect the Workstation to the Switch  
Connect the CPU0 blade Ethernet port directly to the workstation using an Ethernet cable, or indirectly through a  
switch or hub. The Ethernet port automatically discovers straight and cross-over cables. You must have a live  
Ethernet connection when the workstation powers up.  
NOTE:  
The Maintenance Panel Ethernet ports on the front of the switch are disabled and should not be used for the  
initial installation. You can enable the Maintenance Panel Ethernet ports after the switch is operational.  
CPU0 BLADE  
ETHERNET PORT  
Step 7. Install Enterprise Fabric Suite 2007  
The Enterprise Fabric Suite 2007 application includes the Configuration Wizard. This wizard auto-detects and configures  
the switch based on selected options and recommended settings. To install the Enterprise Fabric Suite 2007 application  
on a Windows workstation/server, perform the following steps:t  
1.  
2.  
3.  
4.  
5.  
6.  
Insert the Enterprise Fabric Suite 2007 disk into the CDROM drive.  
Select the Enterprise Fabric Suite 2007 tab at the top of the screen.  
Click Agree in response to the End User License Agreement.  
Select Install for Windows 2003, XP.  
Double click the Windows_6.08.xx.exe file to begin installation.  
Enter the serial number and license key provided to activate the Enterprise Fabric Suite 2007  
application.  
If the product introduction screen does not open, open the CD with Windows Explorer and run the installation program  
with the following path:  
Switch_Manager\Windows_6.08.xx.exe  
Step 8. Obtain Network Configuration  
ObtaintheIPaddressandsubnetmaskfromyournetworkadministrator. Besurethatyourworkstationisconfigured  
for the same subnet.  
5
 
Step 9. Run the Configuration Wizard  
Double-click the Enterprise Fabric Suite 2007 shortcut, or select Enterprise Fabric Suite 2007 from Start menu,  
depending on how you installed it.  
The Configuration Wizard tool auto-detects and configures the switch based on selected options and recommended  
settings. Follow the instructions to set network parameters and the password. The default user name is admin; the  
default password is password.  
NOTE:  
If you are using an Ethernet switch and the auto-connect process fails due to a time out, try a direct connection  
from your workstation to the switch using an Ethernet cross-over cable.  
Step 10. Connect Devices and Switches  
Connect fiber optic cables between the installed transceivers and their corresponding devices. Each port  
auto-negotiates the proper port type with the connected device or switch.  
Congratulations  
You have successfully installed your QLogic SANbox 9000 Series Switch  
6
 
© 2007 QLogic Corporation. QLogic, the QLogic logo, SANbox, and Enterprise Fabric Suite 2007 are trademarks or  
registered trademarks of QLogic Corporation. Microsoft , Windows, and Internet Explorer are registered trademarks of  
the Microsoft Corporation. MacOS X is a registered trademark of Apple Computer, Inc. Linux is a registered trademark  
of Linus Torvalds. Mozilla and Firefox are trademarks or registered trademarks of the Mozilla Foundation. Netscape  
Navigator is a registered trademarks of Netscape Communications Corporation. Java and Solaris are registered  
trademarks of Sun Microsystems, Inc. All other brands and product names are trademarks or registered trademarks of  
their respective owners. Information supplied by QLogic is believed to be accurate and reliable. QLogic Corporation  
assumes no responsibility for any errors in this brochure. QLogic Corporation reserves the right, without notice, to  
makes changes in product design or specifications.  
 
*50688-03  A*  
QLogic Corporation  
949.389.6000  
26650 Aliso Viejo Parkway  
Aliso Viejo, CA 92656  
50688-03 A  
J
 

Grizzly Sander G0538 User Manual
Grizzly Sander G7297 User Manual
Hotpoint Dishwasher BFI68 User Manual
Hotpoint Washer WMD 942 P G A K User Manual
HP Hewlett Packard Car Video System D5063 User Manual
HP Hewlett Packard Electric Shaver HP6409 User Manual
HP Hewlett Packard Printer T3204 User Manual
HP Hewlett Packard Switch GbE2 User Manual
Husqvarna Lawn Mower YTH210XP User Manual
IBM Computer Drive DR550 User Manual