INSTRUCTION MANUAL
VHF TRANSCEIVER
iF15/S
UHF TRANSCEIVER
iF25/S
FOREWORD
PRECAUTION
READ ALL INSTRUCTIONS carefully and completely before
RWARNING! NEVER hold the transceiver so that the antenna
is very close to, or touching exposed parts of the body, especially
the face or eyes, while transmitting. The transceiver will perform
best if the microphone is 5 to 10 cm away from the lips and the
transceiver is vertical.
using the transceiver.
SAVE THIS INSTRUCTION MANUAL— This instruction
manual contains important operating instructions for the IC-F15/
F15S VHF TRANSCEIVER and IC-F25/F25S UHF TRANSCEIVER.
RWARNING! NEVER operate the transceiver with a headset
or other audio accessories at high volume levels.
CAUTION! NEVER short the terminals of the battery pack.
EXPLICIT DEFINITIONS
NEVER connect the transceiver to a power source other than the
BP-230, BP-231 or BP-232. Such a connection will ruin the trans-
ceiver.
DO NOT push the PTT when not actually desiring to transmit.
AVOID using or placing the transceiver in direct sunlight or in
areas with temperatures below –25°C or above +55°C.
WORD
RWARNING
CAUTION
NOTE
DEFINITION
Personal injury, fire hazard or electric shock
may occur.
Equipment damage may occur.
DO NOT modify the transceiver for any reason.
If disregarded, inconvenience only. No risk
of personal injury, fire or electric shock.
MAKE SURE the flexible antenna and battery pack are securely
attached to the transceiver, and that the antenna and battery pack
are dry before attachment. Exposing the inside of the transceiver
to water will result in serious damage to the transceiver.
The use of non-Icom battery packs/chargers may impair transceiver
performance and invalidate the warranty.
OPERATING NOTES
• When transmitting with a portable radio, hold the radio in a vertical
position with its microphone 5 to 10 centimeters away from your
mouth. Keep the antenna at least 2.5 centimeters from your head
and body.
• If you wear a portable two-way radio on your body, ensure that the
antenna is at least 2.5 centimeters from your body when transmit-
ting.
Icom, Icom Inc. and the
logo are registered trademarks of Icom Incorpo-
rated (Japan) in the United States, the United Kingdom, Germany, France, Spain,
Russia and/or other countries.
i
ii
ACCESSORIES
I Supplied accessories
1
1
TABLE OF CONTENTS
The following accessories are supplied:
Qty.
FOREWORD ……………………………………………………………… i
EXPLICIT DEFINITIONS ………………………………………………… i
OPERATING NOTES……………………………………………………… i
PRECAUTION …………………………………………………………… ii
TABLE OF CONTENTS ………………………………………………… iii
1 ACCESSORIES……………………………………………………… 1–5
‘ Supplied accessories………………………………………………… 1
‘ Accessory attachments……………………………………………… 2
2 PANEL DESCRIPTION …………………………………………… 6–11
‘ Front, top and side panels ………………………………………… 6
‘ LED indicator ………………………………………………………… 8
‘ Programmable function keys ……………………………………… 9
3 CONVENTIONAL OPERATION………………………………… 12–18
‘ Turning power ON ………………………………………………… 12
‘ Channel selection ………………………………………………… 12
‘ Call procedure ……………………………………………………… 13
‘ Receiving and transmitting ……………………………………… 14
‘ Scrambler function ………………………………………………… 16
‘ Setting the squelch level ………………………………………… 16
‘ Man Down Emergency Call ……………………………………… 17
4 OPTIONAL UNIT INSTALLATION……………………………… 18–19
‘ Optional unit installation …………………………………………… 18
‘ Scrambler unit installation ………………………………………… 19
5 BATTERY CHARGING ………………………………………… 20–25
‘ Battery charging …………………………………………………… 20
‘ Caution ……………………………………………………………… 21
‘ Optional battery chargers ………………………………………… 22
6 SWIVEL BELT CLIP……………………………………………… 26–29
‘ MB-93 contents …………………………………………………… 26
‘ To attach …………………………………………………………… 26
‘ To detach …………………………………………………………… 28
7 OPTIONS ………………………………………………………… 30–31
8 DOC………………………………………………………………… 32–33
q Flexible antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
w Battery pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
e Belt clip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
r Unit cover (double-sided tape)* . . . . . . . . . . . . . . . . . . . . . . . .1
t Jack cover (with screws) . . . . . . . . . . . . . . . . . . . . . . . . . . .1 set
* Use the unit cover as a spare. Ask your dealer for details.
q
w
e
t
r
iii
1
ACCESSORIES
ACCESSORIES
1
1
I Accessory attachments
1
DFlexible antenna
ï Battery pack
Connect the supplied flexible an-
tenna to the antenna connector.
To attach the battery pack:
Slide the battery pack on the back of the transceiver in the direc-
tion of the arrow (q), then lock it with the battery release button.
• Slide the battery pack until the battery release button makes a ‘click’
sound.
To release the battery pack:
Push the battery release button in the direction of the arrow (w) as
shown below. The battery pack is then released.
CAUTION:
• NEVER HOLD by the antenna
when carrying the transceiver.
• Transmitting without an antenna
may damage the transceiver.
NEVER release or attach the battery pack when the transceiver
is wet or soiled. This may result in water or dust getting into the
transceiver/battery pack and may result in the transceiver being
damaged.
q
w
2
3
ACCESSORIES
ACCESSORIES
1
1
ï Jack cover
DBelt clip
1
Attach the jack cover when the optional speaker-microphone is not
used.
To attach the belt clip:
q Release the battery pack if it is attached.
To attach the jack cover:
To detach the jack cover:
w Slide the belt clip in the direction of the arrow until the belt clip is
q Attach the jack cover to the q Unscrew the screws with a
locked and makes a ‘click’ sound.
[SP MIC] connector.
w Tighten the screws.
phillips screwdriver.
w Detach the jack cover for the
speaker-microphone connec-
tion.
q
w
To detach the belt clip:
w
w
q Release the battery pack if it is attached.
w Pinch the clip (q), and slide the belt clip in the direction of the
arrow (w).
q
w
q
q
4
5
2 PANEL DESCRIPTION
PANEL DESCRIPTION
2
I Front, top and side panels
2
e LED INDICATOR (p. 8)
q
IC-F15S/F25S
IC-F15/F25
➥ Lights red while transmitting.
➥ Lights green while receiving a signal, or when the squelch is
open.
➥ Lights/blinks orange when the matched 2/5-tone code is re-
ceived, according to the pre-programming.
r SPEAKER-MICROPHONE CONNECTOR [SP MIC]
Connects the optional speaker-microphone. (p. 31)
w
e
i
u
[SP MIC] jack cover
Speaker
NOTE: Attach the [SP MIC] jack
cover when the optional speak-
er-microphone is not used. (p. 4)
y
t
r
Microphone
t DEALER-PROGRAMMABLE KEY [Lower]
The desired function can be assigned by your dealer. (p. 9)
y PTT SWITCH [PTT]
Push and hold to transmit; release to receive.
u DEALER-PROGRAMMABLE KEY [Upper]
The desired function can be assigned by your dealer. (p. 9)
i ANTENNA CONNECTOR
Connects the supplied antenna.
DProgrammable key reference
q CHANNEL SW/SELECTOR
• IC-F15S/F25S: Toggle the channel switch to select the pre-pro-
grammed channel 1 or 2.
• IC-F15/F25 : Rotate the channel selector to select the pre-
programmed memory channels.
Upper
Lower
w VOLUME CONTROL [VOL]
Rotate to turn the power ON/OFF and adjust the audio level.
6
7
PANEL DESCRIPTION
PANEL DESCRIPTION
2
2
‘
‘
LED indicator
Programmable function keys
The LED indicator indicates several informa-
tion as follows;
The following functions can be assigned to [Upper] and [Lower]
programmable function keys.
2
(Ref.; R=Red, G=Green, O=Orange)
Consult your Icom dealer or system operator for details concerning
your transceivers programming.
If the programmable function names are bracketed in the following
explanations, the specific key used to activate the function depends
on programming.
• TX: Turns Red while transmitting a signal.
R
SCAN A KEY
• RX: Turns Green while receiving a signal.
➥ This key’s operation depends on the Power ON Scan setting.
When the power ON scan function is turned OFF;
Push to start and cancel scanning operation. In case of trans-
mission during scan, cancels scanning.
G
• Call LED (ON): When receiving a matched 2/5-tone.
When the power ON scan function is turned ON;
Push to pause scanning. Scanning resumes after passing a
specified time period. In case of transmission during scan,
pauses scanning. Scanning resumes after passing a specified
time period.
O O
• Call LED (Blink): When receiving a matched 2/5-tone.
O
O
• Fast/Slow scan: Blinks while Fast/Slow scan is activated.
G
G
SCAN B KEY
Push to start and cancel scanning operation. In case of transmis-
sion during scan, pauses scanning. Scanning resumes after pass-
ing a specified time period.
• Low BATT1: You should charge the battery. (blinks slowly)
G
G
G
• Low BATT2: You must charge the battery. (blinks fast)
PRIORITY CHANNEL KEYS
➥ Push to select the Priority A or Priority B channel.
➥ Push and hold [Prio A (Rewrite)] to rewrite the Prio A channel.
G
G
G
• TX low BATT2: Low BATT2 was detected during TX mode.
MR-CH 1/2/3/4 KEYS
R
R
R
R
Push to select a memory channels 1 to 4 directly.
NOTE: The memory channels 3 and 4 are available for IC-
F15S/F25S when [MR-CH 3] and [MR-CH 4] keys are assigned.
• CH err: Non-programmed channel is selected.
R O R O R O R O R O R O R O R O
8
9
PANEL DESCRIPTION
PANEL DESCRIPTION
2
2
MONITOR KEY
DTMF AUTODIAL KEY
➥ Mute and release the CTCSS (DTCS) or 2-tone squelch mute.
Open any squelch/deactivate any mute while pushing this key.
(LMR operation only)
➥ Activates one of (or two of) the following functions on each chan-
nel independently: (PMR operation only)
Push to transmit the programmed DTMF code.
2
CALL KEYS
Push to transmit a 2/5-tone code.
• Call transmission is necessary before you call another station de-
pending on your signalling system.
• [Call A] and/or [Call B] keys may be available when your system em-
ploys selective ‘Individual/Group’ calls. Ask your dealer which call is
assigned to each key.
• Push and hold to un-mute the channel (audio is emitted; ‘Audible’
condition).
• Push to mute the channel (sets to ‘Inaudible’ only).
• Push to un-mute the channel (sets to ‘Audible’ only).
• Push after the communication is finished to send a ‘reset code’.
NOTE: The un-mute condition (‘Audible’ condition) may auto-
matically return to the mute condition (‘Inaudible‘ condition)
after a specified period.
EMERGENCY KEYS
➥ Push and hold to transmit an emergency call.
➥ When [Emergency Single (Silent)] or [Emergency Repeat
(Silent)] is pushed, an emergency call is transmitted without a
beep emission.
LOCK KEY
• If you want to cancel the emergency call, push (or push and hold)
the key again before transmitting the call.
• The emergency call is transmitted one time only or repeatedly until
receiving a control code depending on the pre-setting.
Push and hold to electronically lock all programmable keys except
the following:
[Call] (incl. Call A and Call B), [Moni(Audi)] and [Emergency] keys.
OUTPUT POWER SELECTION KEY
Select the transmit output power temporarily or permanently, de-
pending on the pre-setting.
• Ask your dealer for the output power level for each selection.
VOICE SCRAMBLER FUNCTION KEYS
➥ Push to turn the voice scrambler function OFF.
➥ Push and hold to turn the voice scrambler function ON.
OPT OUT KEYS
➥ Push to inactivate the connected output signal level.
➥ Push and hold to activate the connected output signal level.
TALK AROUND KEY
➥ Push to turn the talk around function OFF.
➥ Push and hold to turn the talk around function ON.
• The talk around function equalizes the transmit frequency to the re-
ceive frequency for transceiver-to-transceiver communication.
SIREN KEY
Push to emit a siren. This function can be used for situations other
than an emergency alert such as a security alarm for example.
WIDE/NARROW KEY
➥ Push to select the IF bandwidth to wide.
• The wide passband width can be selected from 25.0 or 20.0 kHz
using the CS-F14 CLONING SOFTWARE (PMR operation only.) Ask
your dealer for details.
➥ Push and hold to select the IF bandwidth to narrow.
10
11
CONVENTIONAL OPERATION
I Turning power ON
CONVENTIONAL OPERATION
3
3
I Call procedure
➥ Rotate [VOL] to turn power ON.
When your system employs tone signalling (excluding CTCSS and
DTCS), the call procedure may be necessary prior to voice trans-
mission. The tone signalling employed may be a selective calling
system which allows you to call specific station(s) only and prevent
unwanted stations from contacting you.
[VOL]
3
q Select the desired TX code channel or 2/5-tone code according
to your System Operator’s instructions.
• This may not be necessary depending on programming.
w Push the call key (assigned to one of the dealer programmable
keys.) (p. 11)
e After transmitting a 2/5-tone code, the remainder of your com-
munication can be carried out in the normal fashion.
I Channel selection
IC-F15S/F25S:
Toggle [CHANNEL SWITCH] to select
the channel 1 or 2, or, push one of [MR-
CH 1] to [MR-CH 4] key to select a chan-
nel directly.
Selective calling
Non-selective calling
• The memory channels 3 and 4 are avail-
able when [MR-CH 3] and [MR-CH 4]
keys are assigned.
[CHANNEL SWITCH]
IC-F15/F25:
[CHANNEL
SELECTOR]
Rotate [CHANNEL SELECTOR] to se-
lect the desired operating channel, in se-
quence; or, push one of [MR-CH 1] to
[MR-CH 4] key to select a channel di-
rectly.
AUTOMATIC SCAN TYPE:
Channel setting is not necessary for this type. When turning the
power ON, the transceiver automatically starts scanning. Scanning
stops when receiving a call.
12
13
CONVENTIONAL OPERATION
CONVENTIONAL OPERATION
3
3
I Receiving and transmitting
NOTE: Transmitting without an antenna may damage the trans-
ceiver. See p. 2 for antenna attachment.
DTransmitting notes
• Transmit inhibit function
3
The transceiver has several inhibit functions which restrict trans-
mission under the following conditions:
- The channel is in mute condition.
Receiving:
q Rotate [VOL] to turn power ON.
w Toggle [CHANNEL SWITCH] (IC-F15S/F25S), rotate [CHAN-
NEL SELECTOR] (IC-F15/F25) or push one of [MR-CH 1] to
[MR-CH 4] key to select a channel.
- Channel is busy.
- Un-matched (or matched) CTCSS is received.
- The selected channel is a ‘receive only’ channel.
For IC-F15S/F25S:
The memory channels 3 and 4 are available when [MR-CH 3]
and [MR-CH 4] keys are assigned.
• Time-out timer
After continuous transmission for the pre-programmed time period,
the time-out timer activates, and causes the transceiver to stop
transmitting.
e When receiving a call, adjust the audio output level to a comfort-
able listening level.
• Penalty timer
Once the time-out timer activates, transmission is further inhibited
for a period determined by the penalty timer.
Transmitting:
Wait for the channel to become clear to avoid interference.
q While pushing and holding [PTT], speak into the microphone at
a normal voice level.
DDTMF transmission
If the transceiver has [DTMF Autodial] assigned to it, the automatic
DTMF transmission function is available.
• When a tone signalling system is used, the call procedure de-
scribed on p. 13 may be necessary.
w Release [PTT] to return to receive.
➥ Push [DTMF Autodial] to transmit the DTMF code.
IMPORTANT!: To maximize the readability of your signal;
1. Pause briefly after pushing [PTT].
2. Hold the microphone 5 to 10 cm from your mouth, then speak
into the microphone at a normal voice level.
14
15
CONVENTIONAL OPERATION
CONVENTIONAL OPERATION
3
3
I Scrambler function
I Man Down Emergency Call
The optional voice scrambler units UT-109 (#01) and UT-110 (#01)
provide high performance private communication between stations
with the same scrambler codes.
The man down emergency call function transmits an emergency
call automatically, after the transceiver laying down in a horizontal
position for a pre-set time period. (The optional UT-113 MAN DOWN
UNIT is required.)
3
➥ Push and hold [Scrambler] to turn the scrambler function ON.
➥ Push [Scrambler] to turn the scrambler function OFF.
After the emergency call, the transceiver performs transmission and
reception alternately with the following conditions:
- Transmits the microphone signals.
I Setting the squelch level
- Receives the signal and emits audio.
The squelch circuit mutes the received audio signal depending on
the signal strength.
When the emergency cancel code is received, the function is can-
celled.
q While pushing [PTT] and [Lower],
rotate [VOL] to turn the power ON
to enter the squelch level adjust-
ment mode.
w Push [Upper] to increase the
squelch level (tight squelch) or
[Lower] to decrease the squelch
level (loose squelch).
[VOL]
IMPORTANT!: Set an emergency channel individually, to provide
certain emergency call operation is recommended.
[Upper]
[PTT]
[Lower]
e Rotate [VOL] to turn the power
OFF to fix the squelch level.
16
17
OPTIONAL UNIT INSTALLATION
I Optional unit installation
OPTIONAL UNIT INSTALLATION
4
4
I Scrambler unit installation
Install the optional unit as follows:
q Rotate [VOL] to turn the power OFF, and remove the battery
pack. (p. 3)
The following PC board modification is required when installing the
optional UT-109 or UT-110.
q Rotate [VOL] to turn the power OFF, and remove the battery
pack. (p. 3)
w Remove the unit cover.
4
NOTE: Use a flat head screw driver or a similar flat instru-
ment, and insert into the hollow of the chassis, then lift and
take away the unit cover. (The removed cover cannot be used
again.)
w Remove the unit cover as shown at left (Optional unit installation.)
e Cut the pattern on the PCB at the TX mic circuit (MIC) and RX
AF circuit (DISC) as shown below.
r Install the scrambler unit as shown at left (Optional unit installa-
tion.)
t Replace the unit cover and the battery pack, then rotate [VOL] to
turn the power ON.
e Install the unit as shown below.
*This illustration is
described with the
UT-110.
NOTE: When uninstalling the
scrambler unit
Be sure to re-solder the discon-
nected points at left, otherwise no
TX modulation or AF output is
available.
r Replace the unit cover and the battery pack, then rotate [VOL] to
turn the power ON.
NOTE: The optional UT-109/UT-110 SCRAMBLER UNITS requires
some PC board modifications. Please refer to the additional in-
stallation as at right.
18
19
BATTERY CHARGING
I Battery charging
BATTERY CHARGING
5
5
I Caution
Prior to using the transceiver for the first time, the battery pack must
be fully charged for optimum life and operation.
RDANGER Charge the specified Icom batteries only.
Only tested and approved for use with genuine Icom batteries. Fire
and/or explosion may occur when a third party battery pack or
counterfeit product is charged.
CAUTION: To avoid damage to the transceiver, turn it OFF while
charging.
• Recommended temperature range for charging:
+10°C to +40°C
CAUTION! NEVER insert battery pack/transceiver (with the bat-
tery pack attached) with wet or soiled into the charger. This may re-
sult in corrosion of the charger terminals or damage to the charger.
The charger is not waterproof and water can easily get into it.
5
- The Li-Ion battery functions within –20°C to +60°C
• Use the specified chargers (BC-119N, BC-121N and BC-160).
NEVER use another manufacturer’s charger.
• Use the optional AC adapter. NEVER use another manufacturer’s
AC adapter.
NEVER incinerate used battery packs. Internal battery gas may
cause an explosion.
NEVER immerse the battery pack in water. If the battery pack be-
comes wet, be sure to wipe it dry immediately (particularly the bat-
tery terminals) BEFORE attaching it to the transceiver. Otherwise,
the terminals will become corroded, or cause connection failure,
etc.
Recommendation:
Charge the supplied battery pack for a maximum of up to
10 hours. Li-Ion batteries are different from Ni-Cd batteries in
that it is not necessary to completely charge and discharge them
to prolong the battery life. Therefore, charging the battery in in-
tervals, and not for extended periods is recommended.
NEVER short the terminals of the battery pack. Also, current may
flow into nearby metal objects, such as a necklace, etc. Therefore,
be careful when carrying with, or placing near metal objects, carry-
ing in handbags, etc.
AVOID leaving the battery pack in a fully charged, or completely
discharged condition for long time. It causes shorter battery life. In
case of leaving the battery pack unused for a long time, it must be
kept safely after discharge, or use the battery until the battery indi-
cator appears, then remove it from the transceiver.
If your battery pack seems to have no capacity even after being
charged, fully charge the battery pack again. If the battery pack still
does not retain a charge (or very little), a new battery pack must be
purchased.
20
21
BATTERY CHARGING
BATTERY CHARGING
5
5
I Optional battery chargers
DRapid charging with the BC-160
The optional BC-160 provides rapid charging of optional Li-Ion bat-
tery packs.
ï AD-106 installation
q Install the AD-106 desktop charger adapter into the holder space
of the BC-119N/121N.
• An AC adapter (may be supplied with BC-160 depending on ver-
sion) or the DC power cable (OPC-515L/CP-17L) is additionally
required.
AD-106
Connectors
5
AC adapter
(Not supplied with
some versions.)
BP-231
TRANSCEIVER
Plugs
Optional OPC-515L
(for 13.8 V power
source) or CP-17L
(for 12 V cigarette
lighter socket) can
be used instead of
the AC adapter.
w Connect the plugs of the BC-119N/BC-121N to the AD-106 with
the connector, then install the adapter into the charger with the
supplied screws.
Screws supplied
with the charger
adapter
IMPORTANT!:
Lobs
Ensure the guide
lobs on the bat-
tery pack are
correctly aligned
with the guide
rails inside the
charger adapter.
0
-16
c
b
Guide rail
22
23
BATTERY CHARGING
BATTERY CHARGING
5
5
DRapid charging with the BC-119N+AD-106
The optional BC-119N provides rapid charging of optional Li-Ion
battery packs.
The following items are additionally required:
• One AD-106 (purchase separately).
DRapid charging with the BC-121N+AD-106
The optional BC-121N allows up to 6 battery packs to be charged
simultaneously. The following items are additionally required.
• Six AD-106.
• An AC adapter (BC-124) or the DC power cable (OPC-656)
• An AC adapter (may be supplied with BC-119N depending on ver-
sion) or the DC power cable (OPC-515L/CP-17L).
TRANSCEIVER
5
TRANSCEIVER
BP-231
BP-231
AD-106 charger
adapters are installed
in each slot.
AC adapter
(Not supplied with
some versions.)
AC adapter
(Purchased
separately)
AD-106 charger
adapter is installed
in BC-119N.
Optional OPC-515L
(for 13.8 V power
source) or CP-17L
(for 12 V cigarette
lighter socket) can
IMPORTANT!:
be used instead of
the AC adapter.
IMPORTANT!:
Lobs
Ensure the guide
lobs on the bat-
tery pack are
correctly aligned
with the guide
rails inside the
charger adapter.
Lobs
DC power cable
(OPC-656)
(Connect with the
DC power supply;
13.8 V/at least 7 A)
Ensure the guide
lobs on the battery
pack are correctly
aligned with the
guide rails inside
the charger adapter.
Guide rails
Guide rails
24
25
SWIVEL BELT CLIP
I MB-93 contents
SWIVEL BELT CLIP
6
6
e Clip the belt clip to a part of your belt. And insert the transceiver
into the belt clip until the base clip inserted fully into the groove.
Qty.
q Belt clip …………………………………………………………… 1
w Base clip …………………………………………………………… 1
q
w
6
I To attach
q Release the battery pack if it is attached. (p. 3)
w Slide the base clip in the direction of the arrow until the base clip
is locked and makes a ‘click’ sound.
r Once the transceiver is locked in place, it swivels as illustrated
below.
26
27
SWIVEL BELT CLIP
SWIVEL BELT CLIP
6
6
I To detach
q Turn the transceiver upside down in the direction of the arrow
w Release the battery pack if it is attached. (p. 3)
and pull out from the belt clip.
e Pinch the clip (q), and slide the base clip in the direction of the
arrow (w).
q
w
6
CAUTION:
HOLD THE TRANSCEIVER TIGHTLY, WHEN HANGING OR
DETACHING THE TRANSCEIVER FROM THE BELT CLIP.
Otherwise the transceiver may not be attached to the holder or
swivel properly if the transceiver is accidentally dropped and the
base clip is scratched or damaged.
28
29
OPTIONS
OPTIONS
7
7
DBATTERY PACK
DBELT CLIPS
• MB-93 SWIVEL BELT CLIP
• MB-94 BELT CLIP
• BP-230 Li-Ion BATTERY PACK
7.4 V/800 mAh Li-Ion battery pack, allows approx. 5.5 hours* op-
eration.
Exclusive alligator-type belt clip. The same as supplied with the
transceiver.
• BP-231 Li-Ion BATTERY PACK
7.4 V/1150 mAh Li-Ion battery pack, allows approx. 8 hours* op-
eration. The same as supplied with the transceiver.
• BP-232 Li-Ion BATTERY PACK
7.4 V/2000 mAh Li-Ion battery pack, allows approx. 14 hours* op-
eration.
• MB-96*/96F LEATHER BELT HANGER
*MB-93’s base clip is required.
DDC CABLES
• CP-17L CIGARETTE LIGHTER CABLE
Allows charging of the battery pack through a 12 V cigarette
lighter socket. (For BC-119N)
*Typical operation; Tx:Rx:Stand-by duty cycle=5:5:90
7
DCHARGERS
• BC-119N DESKTOP CHARGER + AD-106 CHARGER ADAPTER
+ BC-145 AC ADAPTER
• OPC-515L/OPC-656 DC POWER CABLES
Allows charging of the battery pack using a 13.8 V power source
instead of the AC adapter.
For rapid charging of battery packs. An AC adapter is supplied
with the charger depending on versions. Charging time: approx. 2
hours when BP-231 is attached.
• BC-121N MULTI-CHARGER + AD-106 CHARGER ADAPTER (6 pcs.)
+ BC-124 AC ADAPTER
For rapid charging of up to 6 battery packs (six AD-106’s are re-
quired) simultaneously. An AC adapter should be purchased sep-
arately. Charging time: approx. 2 hours when BP-231 is attached.
• BC-160 DESKTOP CHARGER + BC-145 AC ADAPTER
For rapid charging of battery packs. An AC adapter is supplied
with the charger depending on versions. Charging time: approx. 2
hours when BP-231 is attached.
OPC-515L: For BC-119N
OPC-656 : For BC-121N
DOTHER OPTIONS
• SP-13 EARPHONE
Provides clear receive audio in noisy environment.
• HM-131L SPEAKER-MICROPHONE
Combination speaker-microphone that provides convenient oper-
ation while hanging the transceiver from your belt.
HM-131L has a moisture proof construction.
• HS-94/HS-95/HS-97 HEADSET + VS-1L VOX/PTT CASE
HS-94: Ear hook type
HS-97: Throat microphone
HS-95: Neck-arm type
DOPTIONAL UNITS
• UT-108 DTMF DECODER UNIT
VS-1L: VOX/PTT switch box for hands-free operation, etc.
• FA-SC73US/FA-SC56VS/FA-SC57VS STUBBY ANTENNAS
Provides pager and code squelch capabilities.
• UT-109 (#01)/UT-110 (#01) SCRAMBLER UNITS
Non-rolling type (UT-109)/Rolling type (UT-110) voice scrambler
unit provides higher communication security.
• UT-113 MAN DOWN UNIT
FA-SC73US: 450–490 MHz
FA-SC57VS: 160–174 MHz
• FA-SC25U/FA-SC57U/FA-SC72U/FA-SC25V/FA-SC55V ANTENNAS
FA-SC25U: 400–430 MHz
FA-SC72U: 470–520 MHz
FA-SC55V: 146–174 MHz
FA-SC56VS: 150–162 MHz
FA-SC57U: 430–470 MHz
FA-SC25V: 136–155 MHz
Provides a measure of safety when working in a hazardous envi-
ronment, etc.
Some options may not be available in some countries. Please ask your
dealer for details.
30
31
DOC
DOC
8
8
CE versions of the IC-F15/S which display the “CE”
This warning symbol indicates that this equipment op-
erates in non-harmonised frequency bands and/or may
be subject to licensing conditions in the country of use.
Be sure to check that you have the correct version of
this radio or the correct programming of this radio, to
comply with national licensing requirement.
symbol on the serial number seal, comply with the
essential requirements of the European Radio and
Telecommunication Terminal Directive 1999/5/EC.
DECLARATION
DECLARATION
OF CONFORMITY
OF CONFORMITY
We Icom Inc. Japan
We Icom Inc. Japan
1-1-32, Kamiminami, Hirano-ku
Osaka 547-0003, Japan
1-1-32, Kamiminami, Hirano-ku
Osaka 547-0003, Japan
0168
0168
8
Declare on our sole responsibility that this equipment complies with the
essential requirements of the Radio and Telecommunications Terminal
Equipment Directive, 1999/5/EC, and that any applicable Essential Test
Suite measurements have been performed.
Declare on our sole responsibility that this equipment complies with the
essential requirements of the Radio and Telecommunications Terminal
Equipment Directive, 1999/5/EC, and that any applicable Essential Test
Suite measurements have been performed.
Düsseldorf 30th June 2004
Düsseldorf 30th July 2004
Place and date of issue
Place and date of issue
Kind of equipment: VHF TRANSCEIVER
Kind of equipment: UHF TRANSCEIVER
Type-designation:
iC-f15/s
Type-designation:
iC-f25/s
Authorized representative name
Authorized representative name
136 174 MHz 12.5 kHz/20 kHz/25 kHz
400–470 MHz 12.5 kHz/20 kHz/25 kHz
Version (where applicable):
Version (where applicable):
This compliance is based on conformity with the following harmonised
standards, specifications or documents:
i) EN 301 489-1 v1.3.1 (Sept 2001)
ii) EN 301 489-5 (August 2000)
This compliance is based on conformity with the following harmonised
standards, specifications or documents:
i) EN 301 489-1 v1.3.1 (Sept 2001)
ii) EN 301 489-5 (August 2000)
iii) EN 60950 (August 1992+A11)
iii) EN 60950 (August 1992+A11)
iv) EN 300 086-2 (March 2001)
iv) EN 300 086-2 (March 2001)
v) EN 300 219-2 (March 2001)
v) EN 300 219-2 (March 2001)
Signature
Signature
vi) EN 300 113-2 (March 2001)
vi) EN 300 113-2 (March 2001)
32
33
MEMO
MEMO
|