TCD
USE & CARE INFORMATION
NOTE: LIFT THE DISPENSER USING THE HANDLES ONLY. DO NOT LIFT THE DISPENSER FROM THE BOTTOM.
BUNN-O-MATIC CORPORATION
POST OFFICE BOX 3227
SPRINGFIELD, ILLINOIS 62708-3227
PHONE: (217) 529-6601 FAX: (217) 529-6644
34106.0001B 01/05 © 2004 Bunn-O-Matic Corporation
INTRODUCTION
These dispensers are designed to mix liquid tea concentrate with water to produce iced tea by the glass or pitcher. The
concentrate can be stored either inside the dispenser. or outside with a hose connection to the dispenser. The dispenser
must be placed on a sturdy counter or shelf.
SET UP AND OPERATING PROCEDURES
1. Remove dispenser from the box and place on a sturdy, level counter.
2. Remove any packing and the brass cap from the end of the water inlet fitting located on the rear of the
dispenser.
3. Turn the dispenser upside down, loosen the faucet wing nut, anr rotate the faucet 180°. Tighten the faucet
wing nut (Do not overtighten).
4. Attach the stainless, 1/4" "L" tube to the water inlet fitting, then attach the water strainer to the tube; tighten
all flare nuts.
Note: The flow direction arrow on the strainer must point towards the dispenser.
5. Attach a 1/4" water line to the water strainer. This supply line must have at least 30 psi of pressure.
6. Using a screwdriver, turn the adjustment screw clockwise until the screw contacts the seat (DO NOT
OVERTIGHTEN).
7. Open the water inlet valve and check for leaks in the system.
8. Place a container under the faucet; fully open the faucet for approximately 10 seconds, then close the
faucet. Discard the water.
9. Place container back under the faucet; open the faucet fully. Adjust the pressure requlator by pulling out
knob to unlock, then rotate the knob clockwise for more pressure or counterclockwise for less pressure.
With the faucet open, pressure should be adjusted to 20 psi.
10. After the correct pressure is set, close the faucet and push the knob in to lock the pressure regulator.
11. Once the proper flow has been achieved, adjust the concentrate needle valve to provide the desired ratio of
concentrate to water.
12. Connect the proper Bag in a Box adapter to the concentrate inlet tube and clamp. If bottle concentrate is
used, connect the stainless formed tube to the inlet hose and clamp.
13. Attach the connector to the Bag in a Box/ or insert the bottle adapter into the bottle.
14. Place a container under the faucet and open faucet until the entire concentrate line is filled and tea is
despensed for approximately 5 seconds. Close the faucet.
15. Place a glass under the faucet and open to fill the glass. Adjust the screw to achieve the desired strength
of tea. To increase the amount of concentrate (stronger tea), turn the adjustment screw counterclockwise
slightly (1/16 to 1/8 of a turn at a time). To reduce the amount of concentrate (weaker tea) turn the adjust-
ment screw clockwise slightly (1/16 to 1/8 of a turn at a time).
16. Dispense a couple of 8 ounce glasses of tea after each adjustment and taste. Continue this process until
the taste profile is achieved.
NOTE: The ratio adjustment setting is very sensitive. Make very small adjustments with the screw, then
taste the results. You should not have to turn the screw very much to change the ratio.
17. Once the desired ratio of concentrate to water has been set, turn off the incoming water supply and open
faucet to relieve the pressure.
18. Turn the dispenser upright on the counter; loosen the faucet wing nut, rotate the handle 180° and tighten
the wing nut securely.
19. Turn the water supply on. The dispenser is now ready for use.
Refer to DISPENSER CLEANING AND SANITIZING card supplied with your dispenser for recom-
mended daily and weekly cleaning.
|