SPLIT TYPE ROOM AIR CONDITIONER
OPERATION MANUAL
HSU-119M07
HSU-129M07
HSU-189M07
HSU-229M07
Please read this operation manual before using the air conditioner.
0010562346
Contents
Cautions
1
Parts and functions
2-4
Operation
Maintenance
5-12
13-15
16
Trouble shooting
Cautions
The machine is adaptive in following situation
I. Applicable ambient temperature range:
Maximum: D.B / W.B
Indoor
32oC/23oC
18oC/14oC
43oC/26oC
18oC
Minimum: D.B / W.B
Cooling
Maximum: D.B
Outdoor
Minimum: D.B
Maximum: D.B
27oC
15oC
24oC/18oC
-7oC/-8oC
Indoor
Minimum: D.B
Heating
Maximum: D.B / W.B
Outdoor
Minimum: D.B / W.B
2. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent
or a similar qualified person. The type of connecting wire is H05RN-F or H07RN-F
3. If the fuse on PC board is broken please change it with the type of T. 3.15A/250V.
4. The distance between the indoor unit and the floor should be more than 2m.
5. The wiring method should be in line with the local wiring standard.
6. After installation, the power plug should be easily reached.
7. The waste battery should be disposed properly.
8. The appliance is not intended to use by young children or infirm persons without supervision.
9.Young children should be supervised ensure that they do not play with the appliance.
10.The appliance must be installed on strong enough supporter.
11.The wiring diagram is attached inside the machine.
1
Parts and Functions
Indoor Unit
Test running switch(manual)
Used only for test running in cooling
when room temp. is below 16oC.
Don't use it in normal operation.
Inlet grille
Emergency switch(manual)
Used when remote controller is lost or
defective. Unit will run temporarily.
Remote signal receiver
A beeping sound is generated when
a signal from remote controller is
received.
Air filter
Vertical flap
Timer mode indicator
Power indicator
Operation mode indicator
Use remote controller to
adjust up and down air flow.
(Don't adjust it manually.)
Lights up when Timer operation
is selected.
Lights up during compressor
running.
Lights up when unit starts.
Actual inlet grille may vary from the one shown in the manual according to
the product purchased
Outdoor Unit
HSU-119M07
HSU-129M07
HSU-189M07
HSU-229M07
OUTLET
INLET
CONNECTING PIPING AND ELECTRICAL WIRING
DRAIN HOSE
2
Parts and Functions
Operation
Buttons and display of the remote controller.
1. Mode display
AUTO
COOL
DRY
FAN
2. SWING display
3. FAN SPEED display
4. SLEEP display
5. LOCK display
6. SIGNAL SENDING
7. TIMER OFF display
8. TIMER ON display
9. CLOCK display
1
5
AUTO
LO
MED
HI
6
7
8
9
10
2
3
ON
OFF
A
U
T
AM
PM
O
oC
4
ON/OFF
TEMP
10. TEMP display
11
12
11. POWER ON/OFF
18
19
Used for unit start and stop.
MODE
FAN
SET
12. MODE
Used to select AUTO run, COOL,
DRY and FAN operation
TIMER
13. FAN
Used to select fan speed LO, MED, HI, AUTO
13
14
20
21
14. HOUR
Used to set clock and timer setting.
CLOCK
SWING
15. SWING
15
Used to set auto fan direction.
16. SLEEP
Used to select sleep mode.
SLEEP
LOCK
17. LOCK
16
17
Used to lock buttons and LCD
display.
RESET
18. TEMP.
22
Used to select your desired temp.
19. SET
Used to confirm timer and clock settings.
20. TIMER
Used to select TIMER ON, TIMER OFF,
TIMER ON-OFF
21. CLOCK
Used to set correct time
22. RESET
Used to reset the controller back to
normal condition.
Clock set
When unit is started for the first time and after replacing batteries in remote controller,
clock should be adjusted as follows:
Press CLOCK button, "AM" or "PM" flashes.
Press or to set correct time. Each press will increase or decrease 1min. If the
button is kept depressed, time will change quickly.
After time setting is confirmed, press SET, "AM "and "PM" stop flashing, while clock
starts working.
NOTE: Cooling only unit do not have displays and functions related with heating
Hints
After replacing with new batteries, remote controller will conduct self-check, displaying
all information on LCD. Then, it will become normal.
3
Parts and Functions
Operation
Buttons and display of the remote controller.
If the unit which you purchased has healthy function, Remote controller should
like the following figure:
1. Mode display
AUTO
COOL
DRY
FAN
1
5
2. SWING display
3. FAN SPEED display
4. SLEEP display
5. LOCK display
6. SIGNAL SENDING
7. TIMER OFF display
8. TIMER ON display
9. CLOCK display
10. TEMP display
11. POWER ON/OFF
MED
HI
LO
AUTO
6
7
8
9
10
ON
OFF
2
3
A
U
T
AM
PM
O
oC
4
ON/OFF
TEMP
11
18
19
Used for unit start and stop.
12. MODE
MODE
FAN
SET
Used to select AUTO run, COOL,
DRY and FAN operation
12
13. FAN
Used to select fan speed LO, MED, HI, AUTO
14. HOUR
Used to set clock and timer setting.
15. SWING
Used to set auto fan direction.
16. SLEEP
Used to select sleep mode.
17. LOCK
Used to lock buttons and LCD
display.
18. TEMP.
Used to select your desired temp.
19. SET
Used to confirm timer and clock settings.
TIMER
13
14
20
21
SWING
CLOCK
15
16
17
SLEEP
LOCK
HEALTH
RESET
22
20. TIMER
Used to select TIMER ON, TIMER OFF,
TIMER ON-OFF
21. CLOCK
Used to set correct time
22. RESET
Used to reset the controller back to
normal condition.
23. HEALTH
Used to set healthy operation
BRIEF INTRODUCTION TO HEALTH OPERATION
The anion generator in the air conditioner can generate a lot of anion to
effectively balance the quantity of position and anion in the air and also to kill
bacteria and speed up the dust sediment in the room and finally clean the air
in the room.
NOTE: Cooling only unit do not have displays and functions related with heating
Hints
After replacing with new batteries, remote controller will conduct self-check, displaying
all information on LCD. Then, it will become normal.
4
Operation
Remote controller's operation
When in use, put the signal transmission head directly to the
receiver hole on the indoor unit.
The distance between the signal transmission head and the
receiver hole should be within 7m without any obstacle as well.
Don't throw the controller, prevent it from being damaged.
When electronic-started type fluorescent lamp or change-over
type fluorescent lamp or wireless telephone is installed in the
room, the receiver is apt to be disturbed in receivering the signals
so the distance to the indoor unit should be shorter.
Loading of the battery
Load the batteries as illustrated. 2 R-03 batteries, resetting key (cylinder)
Remove the battery cover:
Slightly press " " and push down the cover.
ÇëÑ¡ÓÃͬһƷÅÆÁ½½Ú
7#
µç³Ø,³¤Ê±¼ä²»ÓÃʱ,Ϊ
·Àֹ©ҹÇ뽫µç³ØÈ¡
ÇëÑ¡ÓÃͬһƷÅÆÁ½½Ú
7#
µç³Ø,³¤Ê±¼ä²»ÓÃʱ,Ϊ
·Àֹ©ҹÇ뽫µç³ØÈ¡
³ö¡£
ÔÚʹÓÃÖÐÈçÓöÒì³£,Çë
³ö¡£
ÔÚʹÓÃÖÐÈçÓöÒì³£,Çë
½«µç³ØÈ¡³ö,6·ÖÖÓºóÔÙ
×°Èëеç³Ø¡£
½«µç³ØÈ¡³ö,6·ÖÖÓºóÔÙ
×°Èëеç³Ø¡£
º£¶û¼¯ÍÅÇൺº£¶û
º£¶û¼¯ÍÅÇൺº£¶û
¿Õµ÷Æ÷ÓÐÏÞ×ܹ«Ë¾
¿Õµ÷Æ÷ÓÐÏÞ×ܹ«Ë¾
Load the battery:
Be sure that the loading is in line with the" + "/"-"
pole request as illustrated.
Put on the cover again
Confirmation indicator:
In disorderation, reload the batteries or load the new batteries after 6mins.
Note:
Use two new same-typed batteries when loading.
If the remote controller can't run normally or doesn't work at all,
use a sharp pointed item to press the reset key.
Hint:
Remove the batteries in case unit won't be in usage for a long period.
If there are any display after taking-out just need to press reset key.
Power failure resume(please set and apply as necessary)
If sudden power failure occurs, the unit will resume original operation when power is
supplied again.
Note: When sudden power failure happens during unit operation in power failure resume mode, if
the air conditioner is not desired for use in a long period, please shut off the power supply
in case that the unit automatically resume operation when power is re-supplied, or press
ON/OFF to turn off the unit when power resumes.
5
Operation
Enjoy yourself by just a gentle press.
Auto run, Fan operation
(1) Unit start
Press ON/OFF button, unit starts.
Previous operation status appears on display.
(Not Timer setting)
Power indicator on indoor unit lights up.
(2) Select operation mode
Press MODE button. For each press, operation
mode changes as follows:
ON/OFF
TEMP
1
4
MODE
SET
2
FAN
AUTO COOL
DRY
FAN
TIMER
Unit will run in selected mode.
3
Stop display at "
" AUTO or "
"FAN.
SWING
CLOCK
(3) FAN
SLEEP
LOCK
Press FAN button. For each press, fan speed changes
as follows:
RESET
AUTO
LO
MED
HI
(4) Unit stop
Press ON/OFF button.
Unit will run at selected fan speed.
Only time remains on LCD.
All indicators on indoor unit go out.
Vertical flap closed automatically.
Note:AUTO is not available in FAN mode.
Hints
Remote controller can memorize settings in each operation mode. To run it next time just
select the operation mode and it will start with the previous setting.
No reelecting is needed.(TIMER ON/OFF needs reelecting)
Cautions:
Note:
On cooling only unit, heating mode is not available,
After replacing batteries, press ON/OFF, and display
becomes as follows:
Operation mode: AUTO, Temp. No
Timer mode: No, Fan speed :AUTO
The above information is the
explanation of the displayed
information therefore varies
with those displayed in actual
operation.
6
Operation
COOL,HEAT and DRY operation
Recommendations:
Use COOL in summer.
Use DRY in spring, autumn and in damp climate.
(1) Unit start
Press ON/OFF button, unit starts.
Previous operation status appears on display.(Not Timer setting)
Power indicator on indoor unit lights up.
(2) Select operation mode
Press MODE button. For each press, operation
mode changes as follows:
ON/OFF
TEMP
AUTO COOL
DRY
FAN
3
1
6
3
Unit will run in operation mode displayed on LCD.
Stop display at your desired mode.
MODE
SET
2
FAN
TIMER
(3) Select temp. setting
Press TEMR button.
4
SWING
CLOCK
Every time the button is pressed, temp. setting increases 1oC
Every time the button is pressed, temp. setting decreases 1oC
Unit will start running to reach the temp. setting on LCD.
5
SLEEP
(4) Fan speed selection
LOCK
RESET
Press FAN button. For each press, fan speed changes
as follows:
AUTO
LO
MED
HI
COOL operation starts when room
temp. is higher than temp. setting.
Ultra-low air flow
Unit runs at the speed displayed on LCD.
Temp. setting+2o
C
Temp. setting
In DRY mode, when room temperature becomes
lower than temp.setting+2oC,unit will run intermittently
at LOW speed regardless of FAN setting.
On reaching temp. setting, unit
will run in mild DRY mode.
Hints
On cooling only unit, heating mode is not available.
Remote controller can memorize each operation status. When starting it next time,
just press ON/OFF button and unit will run in previous status.
7
Operation
(5) Air flow direction adjustment
After operation mode is selected, vertical flap will open automatically according to the mode.
Referring to the Fig.
COOL
About 10o
Up and down (Use remote controller)
Press SWING button, vertical flap will move within
the range shown in the Fig. Press SWING button
stop it at a fixed position.
Left and right air flow adjustment
(manual)
Move the horizontal blade by a knob on air
conditioner to adjust left and right direction
referring to Fig.
About 10o
COOL
About 45o
Cautions:
Cautions:
It is advisable not to keep vertical flap at
downward position for a long time in COOL
or DRY mode, otherwise, condensate
water might occur.
When humidity is high, condensate water
might occur at air outlet if all horizontal
louvers are adjusted to left or right.
Cautions:
(6) Unit stop
Unit won't restart until 3 minutes have
elapsed, due to system protection.
HEAT mode is not available on
cooling only unit.
Press ON/OFF button.
Only time remains on LCD.
All indicators on indoor unit go out.
Vertical flap closes automatically.
Hints
As cold air flows downward in COOL mode, adjusting air flow horizontally will be much more
helpful for a better air circulation.
Be careful not to catch a cold when cold air blows downward.
It is harmful to your health in summer to go frequently in and out of places where temp.
difference is above 7oC. Temp. difference of 3-5oC will remove your fatigue.
More than this, unit's load can be reduced and power consumption cut down as well. So, you'd
better set a temp. difference of 3-5oC between indoor and outdoor temp. in COOL mode.
8
Operation
TIMER Operation
Set Clock correctly before starting Timer operation
You can let unit start or stop automatically at following times: Before you wake up in the
morning, or get back from outside or after you fall asleep at night.
TIMER ON/OFF
(1)After unit start, select your desired operation mode.
Operation mode will be displayed on LCD.
Power indicator on indoor unit lights up.
(2)TIMER mode selection
ON
Press TIMER button to change TIMER mode.
Every time the button is pressed, display changes as follows:
blank
ON/OFF
TEMP
ON
OFF
ON
OFF
TIMER ON TIMER OFF
TIMER ON-OFF
1
MODE
Select your desired TIMER mode (TIMER ON or TIMER
OFF) ON or OFF will flash.
SET
3
4
FAN
TIMER
(3)Timer setting
3
Press HOUR
/
button.
2
SWING
CLOCK
Every time the button is pressed, time increases 10 min.
If button is kept depressed, time will change quickly.
Every time the button is pressed, time decreases 10 min.
If button is kept depressed, time will change quickly. Time
will be shown on LCD. It can be adjusted within 24 hours.
SLEEP
LOCK
RESET
(4)Confirming your setting
After setting correct time, press SET button to confirm, "ON"
or "OFF" stops flashing
Time displayed: Unit starts or stops at x hour x min. (TIMER
ON or TIMER OFF).
Timer mode indicator on indoor unit lights up.
To cancel TIMER mode
Just press TIMER button several times until TIMER mode disappears.
Hints
After replacing batteries or a power failure happens, Time setting should be reset.
Remote controller possesses memory function, when use TIMER mode next time, just
press SET button after mode selecting if timer setting is the same as previous one.
9
Operation
TIMER ON-OFF
(1)After unit start, select your desired operation mode
Operation mode will be displayed on LCD.
Power indicator on indoor unit lights up.
(2) Press TIMER button to change TIMER mode.
Every time the button is pressed, display changes as follows:
blank
ON
OFF
ON
OFF
TIMER ON TIMER OFF
TIMER ON-OFF
ON
Select TIMER ON-OFF. "ON" will flash.
(3)Time setting for TIMER ON
Press HOUR button.
ON/OFF
TEMP
1
MODE
FAN
Every time the button is pressed, time increases 10 min.
If button is kept depressed, time will change quickly.
Every time the button is pressed, time decreases 10 min.
If button is kept depressed, time will change quickly.
SET
6
3
TIMER
5
4
2
SWING
CLOCK
Time will be shown on LCD.
It can be adjusted within 24 hours.
AM refers to morning and PM to afternoon
SLEEP
LOCK
(4) Time confirming for TIMER ON
After time setting, press TIMER button to confirm.
"ON" stops blinking, While "OFF" starts blinking.
Time displayed: Unit starts at x hour x min.
RESET
(5)Time setting for TIMER OFF
Follow the same procedures in "Time setting for TIMER ON".
(6) Time confirming for TIMER OFF
After time setting, press SET button to confirm, "OFF" stops flashing
Time displayed: Unit stops at X hour X min.
To cancel TIMER mode
Just press TIMER button several times until TIMER mode disappears.
10
Operation
Emergency operation and test operation
Emergency Operation:
Carry out this operation only when the remote controller is defective or lost.
When the emergency operation switch is pressed, a" Pi "sound starts once, which
means the start of this operation.
In this operation, it is not possible to change the
settings of temperature and air flow speed, it is
Pi
also impossible to do an operation by the timer.
Follow the requirements below.
Room
Timer
mode
Designated
temperature
Air flow Operation
temperature
speed
mode
COOL
HEAT
More than 23o
C
26o
C
C
CONTINUOUS AUTO
CONTINUOUS AUTO
Less than 23o
C
23o
If an air conditioner is a model for both cooling and heating.
Cooling when the room temperature at the start of operation is above 23oC.
Heating when the room temperature at the start of operation is below 23oC
Test operation:
Use this switch in the test operation when the room
Pi Pi
temperature is less 16oC, do not use it in the normal
operation.
Continue to press the test operation switch for more
than 5 seconds. After you hear the "Pi" sound twice,
release your finger from the switch, the cooling
operation starts with the air flow speed setting "Hi".
Removal of the restriction of emergency or test operation:
Press once more the emergency operation switch, or manipulate through the remote
controller, a "Pi" sound causes the restriction of emergency or test operation to be
removed.
When the remote controller is manipulated for the removal, then the selected operation
by the remote controller.
11
Operation
Comfortable SLEEP
Before going to bed at night, you can simply press
the SLEEP button and unit will bring you a sound
sleep in selected mode.
ON/OFF
TEMP
In COOL mode
MODE
FAN
SET
One hour after SLEEP mode starts, temp. will
become 1oC higher than temp. setting. After
running for another 1 hour, temp. rises by 1oC
further. Unit will run for 6 hours then stops
automatically. Temp. is higher than temp.
setting so that room temp. won't be too low
for your sleep.(As shown in Fig.l)
TIMER
SWING
CLOCK
SLEEP
LOCK
RESET
Power Failure Resume Function
SLEEP operation starts
SLEEP operation stops
Approx. 6 hrs
If the unit is started for the first time, the
compressor will not start running unless 3
minutes have elapsed. When the power
resumes after power failure, the unit will run
automatically, the power indicator lights up, and
3 minutes later the compressor starts running
with the indicator lighting up.
1 hr
Rises 1oC
1 hr
Rises 1oC
Temp. setting
Unit stop
Note:
Fig.1
In AUTO mode, unit will run in SLEEP
function according to operation mode.
In FAN mode, comfortable sleep is not
available.
12
Maintenance
Different models have different appearance
Cleaning of unit casing
Cut off power supply
before cleaning unit casing with soft cloth.
In case of heavy stain, clean it with neutral detergent.
squeeze water in the cloth, wipe off the detergent on unit
casing completely.
Cleaning of remote controller
Don't use water to wash unit casing, please use dry cloth.
Don't use glass cleaner or cloth soaked with chemicals.
Cleaning of air filter
Air Filter
1.Open inlet grille by pulling it upward. 2.Remove air filter
Push up the filter's center tab
slightly until it is caesura of
the stopper. Remove it by
pulling down.
3.Clean the filter
Use a vacuum
cleaner to remove
dust,or wash the
filter with water.
After washing,
dry the filter
completely in the shade.
4.Attach the filter
Attach filter behind the stopper so that
the "Front" indication is facing to the front. Make sure
that it is completely behind the stopper, otherwise
problems might occur.
5.Close the inlet grille.
13
Maintenance
Replacement of Air Purifying Filter
NOTE: Air purifying filter is optional part
1.Open the lnlet Grille
Open the inlet grille by pushing each ends of
the inlet grille upward.(use thumbs to push
up)
2.Detach the standard air filter
Slide the knob slightly upward to release the
filter, then withdraw it.
3.Detach the Air Purifying Filter
Replace the old filter with
new one into the frame.
4.Attach new Air Purifying Filter
Attaching each of the Air Purifying Filter to the
indoor unit as its white side faces to the front .
5.Attach the standard air filter as its
front side faces to the front
Operating without standard air filter may
cause troubles with the machine.
6.Close the Inlet Grille
Close the Grille surely
NOTE:
Please replace the air Purifying Filter when color of the filter become same levle of
sample attached in the indoor unit.
Please replace the air Purifying Filter in 3-6 months as standard.
Stuffed filter are not usable even washing.Please purchase new one at sales shop.
14
Maintenance
Better use of air conditioner
Proper room temperature.
Cleaning of the air filter.
Once every
two weeks
Proper
temperature
Effective use of the timer.
Closing of doors and windows
during operation
Curtains or blinds
for windows
Avoid time-wasteful
operation
Never fail to observe the followings
Do not sprinkle water over
the unit.
Do not block the inlet or outlet.
Do not pull power plug.
Do not use for other purposes.
Such as food preservation
plant cultivation or animal
breeding.
15
Trouble shooting
Before asking for service, check the following first.
Phenomenon
Cause or check points
The system does not restart
immediately.
When unit is stopped, it won't restart
immediately until 3 minutes have elapsed
to protect the system.
When the electric plug is pulled out and
reinserted, the protection circuit will work
for 3 minutes to protect the air conditioner.
During unit operation or at stop, a swishing
or gurgling noise may be heard. At first 2-3
minutes after unit start, this noise is more
noticeable. (This noise is generated by
refrigerant flowing in the system.)
Noise is heard
Normal
Performance
inspection
During unit operation, a cracking noise may
be heard. This noise is generated by the
casing expanding or shrinking because of
temperature changes
Should there be a big noise from air flow in
unit operation, air filter may be too dirty.
This is because the system circulates smells
from the interior air such as the smell of
furniture, cigarettes.
Smells are generated.
Mist or steam are blown out.
During COOL or DRY operation, indoor unit
may blow out mist. This is due to the sudden
cooling of indoor air.
Does not work at all.
Poor cooling
Is power plug inserted?
Is there a power failure?
Is fuse blown out?
Multiple
check
Is the air filter dirty? Normally it should be
cleaned every 15 days.
Are there any obstacles before inlet and outlet?
Is temperature set correctly?
Are there some doors or windows left open?
Is there any direct sunlight through the
window during the cooling operation?(Use
curtain)
Are there too much heat sources or too many
people in the room during cooling operation?
Application temp. range of air conditioner -7oC~43oC.
16
|