INTRODUCTION
Thank you for purchasing a Honda engine. We want to help you to get
the best results from your new engine and to operate it safely. This
manual contains information on how to do that; please read it carefully
before operating the engine. If a problem should arise, or if you have
any questions about your engine, consult an authorized Honda
servicing dealer.
All information in this publication is based on the latest product
information available at the time of printing. American Honda Motor
Co., Inc. reserves the right to make changes at any time without notice
and without incurring any obligation. No part of this publication may be
reproduced without written permission.
OWNER’S MANUAL
GXV160
This manual should be considered a permanent part of the engine and
should remain with the engine if resold.
SAFETY MESSAGES
Your safety and the safety of others is very important. We have
provided important safety messages in this manual and on the engine.
Please read these messages carefully.
A safety message alerts you to potential hazards that could hurt you or
others. Each safety message is preceded by a safety alert symbol
and one of three words: DANGER, WARNING, or CAUTION.
These signal words mean:
WARNING:
You WILL be KILLED or SERIOUSLY
HURT if you don't follow instructions.
DANGER
The engine exhaust from this product
contains chemicals known to the State
of California to cause cancer, birth
defects or other reproductive harm.
You CAN be KILLED or SERIOUSLY
HURT if you don't follow instructions.
WARNING
POM51741G
25,000.2003.03
31ZE7614
00X31-ZE7-6140
IPC
You CAN be HURT if you don't follow
instructions.
EM3
PRINTED IN U.S.A.
CAUTION
CONTENTS
Each message tells you what the hazard is, what can happen, and
what you can do to avoid or reduce injury.
INTRODUCTION . . . . . . . . . . . . . . 1
SAFETY MESSAGES . . . . . . . . . 1
Damage Prevention
Messages . . . . . . . . . . . . . . . . . . 1
Safety Information. . . . . . . . . . . 1
COMPONENT & CONTROL
LOCATION . . . . . . . . . . . . . . . . . . 2
THROTTLE CABLE
CONNECTION. . . . . . . . . . . . . . . . 2
BEFORE OPERATION
CHECKS . . . . . . . . . . . . . . . . . . . . 2
Is Your Engine Ready To Go . . 2
OPERATION . . . . . . . . . . . . . . . . . 2
Safe Operating Precautions . . . 2
Starting the Engine . . . . . . . . . 3
Setting Engine Speed . . . . . . . . 3
Stopping the Engine . . . . . . . . 3
SERVICING YOUR ENGINE. . . . 3
The Importance of
Maintenance. . . . . . . . . . . . . . . . 3
Maintenance Safety . . . . . . . . . 3
Safety Precautions . . . . . . . . . . 3
Maintenance Schedule . . . . . . . 4
Refueling . . . . . . . . . . . . . . . . . . 4
Fuel Recommendations . . . . . . 4
Engine Oil . . . . . . . . . . . . . . . . . 5
Air Cleaner . . . . . . . . . . . . . . . . 6
Spark Plug . . . . . . . . . . . . . . . . . 6
Idle Speed Adjustment . . . . . . . 6
Spark Arrester . . . . . . . . . . . . . . 7
HELPFUL TIPS &
SUGGESTIONS. . . . . . . . . . . . . . . 8
Storing Your Engine . . . . . . . . . 8
Draining The Fuel Tank And
Carburetor . . . . . . . . . . . . . . . . . 8
Adding A Gasoline Stabilizer
To Extend Fuel Storage Life. . . 8
Transporting . . . . . . . . . . . . . . . 9
TAKING CARE OF UNEXPECTED
PROBLEMS. . . . . . . . . . . . . . . . . . 9
TECHNICAL & CONSUMER
INFORMATION . . . . . . . . . . . . . . . 9
TECHNICAL INFORMATION . . . . 9
Serial Number Location . . . . . . 9
High Altitude Operation . . . . . . 9
Oxygenated Fuels . . . . . . . . . . 9
Emission Control System
Information. . . . . . . . . . . . . . . . 10
Air Index. . . . . . . . . . . . . . . . . . 10
Specifications . . . . . . . . . . . . . 10
CONSUMER INFORMATION . . . 11
Honda Publications. . . . . . . . . 11
Distributor’s Limited Warranty11
Emission Control System
DAMAGE PREVENTION MESSAGES
You will also see other important messages that are preceded by the
word NOTICE.
This word means:
Your engine or other property can be
NOTICE
damaged if you don’t follow instructions.
The purpose of these messages is to help prevent damage to your
engine, other property, or the environment.
SAFETY INFORMATION
• Understand the operation of all controls and learn how to stop the
engine quickly in case of emergency. Make sure the operator
receives adequate instruction before operating the equipment.
• Your engine’s exhaust contains poisonous carbon monoxide. Do not
run the engine without adequate ventilation, and never run the
engine indoors.
• The engine and exhaust become very hot during operation. Keep
the engine at least 3 feet (1 meter) away from buildings and other
equipment during operation. Keep flammable materials away, and
do not place anything on the engine while it is running.
Warranty. . . . . . . . . . . . . . . . . . 11
Distributor/Dealer Locator
Information. . . . . . . . . . . . . . . . 12
Warranty Service
Information. . . . . . . . . . . . . . . . 12
© 2000 - 2003 American Honda Motor Co., Inc.—All Rights Reserved
1
STARTING THE ENGINE
SERVICING YOUR ENGINE
FUEL VALVE
1. Turn the fuel valve to the ON
position.
THE IMPORTANCE OF MAINTENANCE
Good maintenance is essential for safe, economical and trouble-free
operation. It will also help reduce pollution.
ON
OFF
WARNING
Improper maintenance, or failure to correct a problem
before operation, can cause a malfunction in which you
can be seriously hurt or killed.
2. FOR STARTING A COLD
ENGINE: Move the throttle
control to the choke position.
IDLE
FAST
CHOKE
Always follow the inspection and maintenance
recommendations and schedules in this owner’s manual.
3. FOR RESTARTING A WARM
ENGINE: Do not use the choke
when the engine is warm.
To help you properly care for your engine, the following pages include
a maintenance schedule, routine inspection procedures, and simple
maintenance procedures using basic hand tools. Other service tasks
that are more difficult, or require special tools, are best handled by
professionals and are normally performed by a Honda technician or
other qualified mechanic.
Move the throttle control slightly
past the idle position.
4. FLYWHEEL BRAKE MODELS:
Move the flywheel brake lever
(located on equipment) to release the flywheel brake.
The maintenance schedule applies to normal operating conditions. If
you operate your engine under severe conditions, such as sustained
high-load or high-temperature operation, or use in unusually wet or
dusty conditions, consult your servicing dealer for recommendations
applicable to your individual needs and use.
5. Pull the starter grip lightly until resistance is felt, then pull briskly.
NOTICE
Do not allow the starter grip to snap back against the engine.
Return it gently to prevent damage to the starter.
Maintenance, replacement, or repair of the emission control
devices and systems may be performed by any engine repair
establishment or individual, using parts that are “certified” to
EPA standards.
6. If the choke was used to start the engine, move the throttle to the
fast (or high) position as soon as the engine warms up enough to
run smoothly without use of the choke.
MAINTENANCE SAFETY
7. FLYWHEEL BRAKE MODELS: Continue to hold the flywheel brake
lever (located on equipment). The engine will stop if you release the
flywheel brake lever.
Some of the most important safety precautions follow. However, we
cannot warn you of every conceivable hazard that can arise in
performing maintenance. Only you can decide whether or not you
should perform a given task.
SETTING ENGINE SPEED
Position the throttle control for the desired engine speed. For best
engine performance, it is recommended the engine be operated with
the throttle in the FAST (or high) position.
WARNING
Failure to properly follow maintenance instructions and
precautions can cause you to be seriously hurt or killed.
STOPPING THE ENGINE
IDLE
STOP
Always follow the procedures and precautions in this
owner’s manual.
1. Move the throttle control to the
slow (IDLE) position.
SAFETY PRECAUTIONS
• Make sure the engine is off before you begin any maintenance or
repairs. This will eliminate several potential hazards:
2. Move the throttle control to the
stop position.
3. FLYWHEEL BRAKE MODELS:
Release the flywheel brake lever
(located on equipment) to stop
the engine.
– Carbon monoxide poisoning from engine exhaust.
Be sure there is adequate ventilation whenever you operate
the engine.
– Burns from hot parts.
Let the engine and exhaust system cool before touching.
– Injury from moving parts.
4. Turn the fuel valve to the OFF
position if you do not intend to
restart the engine soon.
FUEL VALVE
Do not run the engine unless instructed to do so.
• Read the instructions before you begin, and make sure you have
the tools and skills required.
ON
• To reduce the possibility of fire or explosion, be careful when
working around gasoline. Use only a nonflammable solvent, not
gasoline, to clean parts. Keep cigarettes, sparks and flames away
from all fuel related parts.
OFF
Remember that an authorized Honda servicing dealer knows your
engine best and is fully equipped to maintain and repair it.
To ensure the best quality and reliability, use only new genuine Honda
parts or their equivalents for repair and replacement
3
MAINTENANCE SCHEDULE
REFUELING
Use unleaded gasoline with a pump octane rating of 86 or higher. This
engine is certified to operate on unleaded gasoline. Unleaded gasoline
produces fewer engine and spark plug deposits and extends exhaust
system life.
REGULAR SERVICE
PERIOD (4)
Before First Every 3 Every 6 Every Every
Each Month Months Months Year Two
Use
or
or
or
or
Years
ITEM
5 Hrs 25 Hrs 50 Hrs 100 or 250
Page
Perform at every indicated month or
operating hour interval, whichever comes
first.
Hrs
Hrs
WARNING
Gasoline is highly flammable and explosive, and you can
be burned or seriously injured when refueling.
Engine oil
Check
O
O
5
6
6
Replace
Check
O
O (2)
Air cleaner
• Stop engine and keep heat, sparks, and flame away.
• Refuel only outdoors.
Clean
O (1)
Replace
Check-adjust
Replace
Check
O
O
• Wipe up spills immediately.
Spark plug
O
Flywheel brake pad
Spark arrester
Idle speed
O
7
7
6
NOTICE
Clean
O
Fuel can damage paint and some types of plastic. Be careful not to
spill fuel when filling your fuel tank. Damage caused by spilled fuel is
not covered under the Distributor’s Limited Warranty (see page 11).
Check-adjust
Clean
O(3)
Fuel tank and filter
Shop
manual
O(3)
Fuel tube
Check
Every 2 years
(Replace if necessary) (3)
Shop
manual
Never use stale or contaminated gasoline or oil/gasoline mixture.
Avoid getting dirt or water in the fuel tank
Valve clearance
Combustion chamber
Check-adjust
Clean
Shop
manual
O(3)
Adding Fuel
After every 300 hours (3)
—
1. Remove the fuel tank cap.
(1) Service more frequently when used in dusty areas.
FUEL TANK CAP
(2) Change engine oil every 25 hours when used under heavy load or
in high ambient temperatures.
FUEL
LEVEL
LIMIT
(3) These items should be serviced by an authorized Honda servicing
dealer, unless you have the proper tools and are mechanically
proficient. Refer to the Honda shop manual for service
procedures.
(4) For commercial use, log hours of operation to determine proper
maintenance intervals.
2. Add fuel to the bottom of the fuel level limit in the neck of the fuel
tank. Do not overfill. Wipe up spilled fuel before starting the engine.
Fuel tank capacity: 0.53 US gal (2.0 l)
4
ENGINE OIL
Oil Change
Recommended Oil
Drain the engine oil when the engine is warm. Warm oil drains quickly
and completely.
Use 4-stroke motor oil that meets or exceeds the requirements for API
service classification SH, SJ, or equivalent. Always check the API
service label on the oil container to be sure it includes the letters SH,
SJ, or equivalent.
OIL FILLER
CAP/
DIPSTICK
OIL FILLER
CAP/
DIPSTICK
UPPER
LIMIT
LOWER
LIMIT
100oF
SEALING WASHER
DRAIN BOLT
SAE 10W-30 is recommended for general use. Other viscosities
shown in the chart may be used when the average temperature in your
area is within the indicated range.
1. Turn the fuel valve to the OFF position to reduce the possibility of
fuel leakage (see page 3).
Oil Level Check
2. Place a suitable container next to the engine to catch the used oil.
1. Check the oil with the engine stopped and level.
2. Remove the oil filler cap/dipstick and wipe it clean.
3. Remove the drain bolt and drain the oil into the container by slightly
tipping the engine toward the oil filler cap/dipstick.
3. Insert the oil filler cap/dipstick into the oil filler neck as shown, but
do not screw it in, then remove it to check the oil level.
Please dispose of used motor oil in a manner that is compatible
with the environment. We suggest you take used oil in a sealed
container to your local recycling center or service station for
reclamation. Do not throw it in the trash, pour it on the ground, or
pour it down a drain.
4. If the oil level is near or below the lower limit mark on the dipstick,
fill with the recommended oil to the upper limit mark. Do not overfill.
5. Reinstall the oil filler cap/dipstick.
4. With the engine in a level position, fill to the upper limit mark on the
dipstick with the recommended oil (see above).
Engine Oil Capacity: 0.69 US qt (0.65 l)
NOTICE
Running the engine with a low oil level can cause engine damage.
5. Reinstall the oil filler cap/dipstick securely.
OIL FILLER CAP/DIPSTICK
UPPER LIMIT
LOWER LIMIT
5
AIR CLEANER
SPARK PLUG
A dirty air cleaner will restrict air flow to the carburetor and cause poor
engine performance. Inspect the elements each time the engine is
operated. You will need to clean the elements more frequently if you
operate the engine in very dusty areas.
Recommended spark plugs: BPR5ES (NGK)
W16EPR-U (DENSO)
The recommended spark plugs are the correct heat range for normal
engine operating temperatures.
NOTICE
NOTICE
Operating the engine without an air cleaner or with a damaged air
cleaner, will allow dirt to enter the engine, causing rapid engine wear.
This type of damage is not covered under the Distributor’s Limited
Warranty (see page 11).
Incorrect spark plugs can cause engine damage.
For good performance, the
SPARK PLUG
SPARK PLUG CAP
spark plug must be properly
WRENCH
gapped and free of deposits.
Inspection
WING BOLT
1. Disconnect the cap from
the spark plug, and
1. Remove the two wing bolts,
then remove the air cleaner
remove any dirt from the
spark plug area.
AIR CLEANER
cover. Be careful to prevent
COVER
dirt and debris from falling
into the air cleaner base.
2. Use the proper size spark
plug wrench to remove the
spark plug.
2. Remove the paper element
PAPER
ELEMENT
and the foam element from
the air cleaner base.
3. Inspect the spark plug. Replace it if
damaged, badly fouled, if the
sealing washer is in poor condition,
or if the electrode is worn. If the
spark plug is to be reused, clean it
with a wire brush.
0.028 ~ 0.031 in
(0.70 ~ 0.80 mm)
FOAM
ELEMENT
3. Remove the foam element
from the paper element.
4. Inspect the filter elements.
Replace damaged
AIR CLEANER
BASE
SEALING
WASHER
elements. Clean or replace
dirty elements.
4. Measure the electrode gap with a
suitable gauge. The correct gap is
0.028 - 0.031 in (0.70 - 0.80 mm). If
adjustment is needed, correct the
gap by carefully bending the side
electrode.
Cleaning
1. Remove the air cleaner
cover and foam element,
as described in the
INSPECTION procedure
above.
5. Install the spark plug carefully, by
hand, to avoid cross-threading.
2. Remove the paper element from the air cleaner base.
6. After the spark plug is seated, tighten with the proper size spark
plug wrench to compress the washer.
3. Paper element: Tap the element several times on a hard surface to
remove excess dirt, or blow compressed air [not exceeding 30 psi
(207 kPa)] through the element from the wire screen side. Never try
to brush off dirt; brushing will force dirt into the fibers. Replace the
paper element if it is excessively dirty.
7. When installing a new spark plug, tighten 1/2 turn after the spark
plug seats to compress the washer.
8. When reinstalling the original spark plug, tighten 1/8 - 1/4 turn after
the spark plug seats to compress the washer.
4. Foam element: Clean in warm, soapy water or nonflammable
solvent, rinse and dry thoroughly. Do not use gasoline as a cleaning
solvent, because that would create a risk of fire or explosion. Dip
the element in clean engine oil, then squeeze out all excess oil.
NOTICE
A loose spark plug can become very hot and can damage the
engine. Overtightening the spark plug can damage the threads in
the cylinder head.
Excess oil will restrict air flow through the foam element and may
transfer to the paper element, soaking and clogging it.
9. Attach the spark plug cap to the spark plug.
5. Wipe dirt from the air cleaner base and cover using a moist rag. Be
careful to prevent dirt from entering the air duct that leads to the
carburetor.
IDLE SPEED ADJUSTMENT
1. Start the engine outdoors,
and let it warm up to normal
operating temperature.
6. Reinstall the air cleaner elements, and make sure both elements
are properly positioned. Install the air cleaner cover and tighten the
two wing bolts securely.
2. Move the throttle control to
the slow (IDLE) position.
3. Using a screwdriver, turn the
throttle stop screw to obtain
the standard idle speed or
the idle speed specified by
the equipment
manufacturer.
THROTTLE STOP SCREW
Standard Idle Speed:
N type: 1,700 ± 150 rpm
A type: 2,100 ± 150 rpm
6
FLYWHEEL BRAKE INSPECTION (A types only)
SPARK ARRESTER (optional equipment)
1. Check to see if the inspection
screw is contacting the brake
bracket.
In some areas, it is illegal to operate an engine without a USDA
(United States Department of Agriculture)-qualified spark arrester.
Check local laws and regulations. A USDA-qualified spark arrester is
available from an authorized Honda servicing dealer.
2. If the inspection screw is
contacting the brake bracket,
take the engine to an
The spark arrester must be serviced every 100 hours to keep it
functioning as designed.
authorized Honda engine
servicing dealer for flywheel
brake pad inspection.
If the engine has been running, the muffler will be hot. Allow it to cool
before servicing the spark arrester.
INSPECTION
SCREW
BRAKE
BRACKET
Spark Arrester Removal
3. Release the flywheel brake
lever (located on equipment),
and verify that there is a strong
resistance when pulling on the
recoil starter. Also verify that
the governor arm is moved to
the idle (slow), position and
there is freeplay in the cable.
The cable freeplay should be
10 - 15 mm from the centerline
as shown when the cable is
new.
1. Remove the two nuts from the muffler shield, using a 10 mm
wrench.
2. Remove the muffler shield, identification plate and muffler.
3. Remove the spark arrester from the muffler.
BRAKE
CABLE
CABLE
FREE
PLAY
MUFFLER
MUFFLER
SHIELD
4. Move the flywheel brake
lever to release the flywheel
brake, and verify that there
is clearance between the
governor arm and the
STOPPER
GASKET
SPARK
ARRESTER
throttle return rod when the
throttle is in the fast (or high)
position.
IDENTIFICATION
PLATE
6 mm NUTS
THROTTLE
RETURN
ROD
Also verify that there is at
least 2 mm clearance
between the stopper and the
brake cable bracket.
BRAKE
CABLE
BRACKET
Spark Arrester Cleaning & Inspection
GOVERNOR
ARM
CLEARANCE
1. Use a brush to remove carbon deposits
from the spark arrester screen. Be
careful not to damage the screen.
Replace the spark arrester if it has
breaks or holes.
2. Install the spark arrester in the reverse
order of removal.
7
HELPFUL TIPS & SUGGESTIONS
DRAINING THE FUEL TANK AND CARBURETOR
STORING YOUR ENGINE
Storage Preparation
WARNING
Gasoline is highly flammable and explosive, and you can
be burned or seriously injured when handling fuel.
Proper storage preparation is essential for keeping your engine
trouble-free and looking good. The following steps will help to keep
rust and corrosion from impairing your engine’s function and
appearance, and will make the engine easier to start when you use it
again.
• Stop engine and keep heat, sparks, and flame away.
• Refuel only outdoors.
• Wipe up spills immediately.
Cleaning
1. Place an approved gasoline container below the carburetor, and
use a funnel to avoid spilling fuel.
If the engine has been running, allow it to cool for at least half an hour
before cleaning. Clean all exterior surfaces, touch up any damaged
paint, and coat other areas that may rust with a light film of oil.
2. Remove the drain bolt, then move the fuel valve lever to the ON
position (see page 2).
3. After all the fuel has drained into the container, reinstall the drain
bolt and washer. Tighten the drain bolt securely.
NOTICE
Using a garden hose or pressure washing equipment can force water
into the air cleaner or muffler opening. Water in the air cleaner will
soak the air cleaner elements, and water that passes through the air
cleaner or muffler can enter the cylinder, causing damage.
Fuel
Gasoline will oxidize and deteriorate in storage. Deteriorated gasoline
will cause hard starting, and it leaves gum deposits that clog the fuel
system. If the gasoline in your engine deteriorates during storage, you
may need to have the carburetor, and other fuel system components,
serviced or replaced.
FLOAT BOWL
WASHER
DRAIN BOLT
The length of time that gasoline can be left in your fuel tank and
carburetor without causing functional problems will vary with such
factors as gasoline blend, your storage temperatures, and whether the
fuel tank is partially or completely filled. The air in a partially filled fuel
tank promotes fuel deterioration. Very warm storage temperatures
accelerate fuel deterioration. Fuel problems may occur within a few
months, or even less if the gasoline was not fresh when you filled the
fuel tank.
Engine Oil
1. Change the engine oil (see page 5).
2. Remove the spark plug (see page 6).
SPARK PLUG
HOLE
OIL
3. Pour a tablespoon (5 - 10 cc) of clean
engine oil into the cylinder.
4. Pull the recoil starter several times to
distribute the oil.
Fuel system damage or engine performance problems resulting from
neglected storage preparation are not covered under the Distributor’s
Limited Warranty (see page 11).
5. Reinstall the spark plug.
Storage Precautions
You can extend fuel storage life by adding a gasoline stabilizer that is
formulated for that purpose, or you can avoid fuel deterioration
problems by draining the fuel tank and carburetor.
If your engine will be stored with gasoline in the fuel tank and
carburetor, it is important to reduce the hazard of gasoline vapor
ignition. Select a well-ventilated storage area away from any appliance
that operates with a flame, such as a furnace, water heater, or clothes
dryer. Also avoid any area with a spark-producing electric motor, or
where power tools are operated.
ADDING A GASOLINE STABILIZER TO EXTEND FUEL
STORAGE LIFE
When adding a gasoline stabilizer, fill the fuel tank with fresh gasoline.
If only partially filled, air in the tank will promote fuel deterioration
during storage. If you keep a container of gasoline for refueling, be
sure that it contains only fresh gasoline.
If possible, avoid storage areas with high humidity, because that
promotes rust and corrosion.
If there is gasoline in the fuel tank, leave the fuel valve in the OFF
position (see page 3).
1. Add gasoline stabilizer following the manufacturer’s instructions.
Keep the engine level in storage. Tilting can cause fuel or oil leakage.
2. After adding a gasoline stabilizer, run the engine outdoors for 10
minutes to be sure that treated gasoline has replaced the untreated
gasoline in the carburetor.
With the engine and exhaust system cool, cover the engine to keep
out dust. A hot engine and exhaust system can ignite or melt some
materials. Do not use sheet plastic as a dust cover. A nonporous cover
will trap moisture around the engine, promoting rust and corrosion.
3. Stop the engine, and turn the fuel valve to the OFF position (see
page 3).
Removal From Storage
Check your engine as described in the BEFORE OPERATION
CHECKS section of this manual (see page 2).
If the fuel was drained during storage preparation, fill the tank with
fresh gasoline. If you keep a container of gasoline for refueling, be
sure it contains only fresh gasoline. Gasoline oxidizes and deteriorates
over time, causing hard starting.
If the cylinder was coated with oil during storage preparation, the
engine will smoke briefly at startup. This is normal.
8
TRANSPORTING
Carburetor Modification For High Altitude Operation
Keep the engine level when transporting to reduce the possibility of
fuel leakage. Turn the fuel valve to the OFF position (see page 3).
At high altitude, the standard carburetor air-fuel mixture will be too rich.
Performance will decrease, and fuel consumption will increase. A very
rich mixture will also foul the spark plug and cause hard starting.
Operation at an altitude that differs from that at which this engine was
certified, for extended periods of time, may increase emissions.
TAKING CARE OF UNEXPECTED PROBLEMS
ENGINE WILL NOT
START
Possible Cause
Correction
High altitude performance can be improved by specific modifications to
the carburetor. If you always operate your engine at altitudes above
5,000 feet (1,500 meters), have your servicing dealer perform this
carburetor modification. This engine, when operated at high altitude
with the carburetor modifications for high altitude use, will meet each
emission standard throughout its useful life.
1. Check control positions. Fuel valve OFF.
Choke OFF.
Move lever to ON.
Move the choke/throttle
lever to CHOKE ON
position unless engine is
warm.
Ignition switch OFF.
Move the throttle lever to
FAST position.
(A type: flywheel brake
lever to RUN position.)
Even with carburetor modification, engine horsepower will decrease
about 3.5% for each 1,000-foot (300-meter) increase in altitude. The
effect of altitude on horsepower will be greater than this if no
carburetor modification is made.
2. Check fuel.
Out of fuel.
Refuel.
Bad fuel; engine stored
without treating or draining
Drain the fuel tank and
carburetor (p. 8). Refuel
gasoline, of refueled with bad with fresh gasoline.
gasoline.
NOTICE
3. Remove and inspect
spark plug.
Spark plug faulty, fouled, or
improperly gapped.
Clean or replace the spark
plug (p. 6).
When the carburetor has been modified for high altitude operation, the
air-fuel mixture will be too lean for low altitude use. Operation at
altitudes below 5,000 feet (1,500 meters) with a modified carburetor
may cause the engine to overheat and result in serious engine
damage. For use at low altitudes, have your servicing dealer return the
carburetor to original factory specifications.
Spark plug wet with fuel
(flooded engine).
Dry and reinstall spark
plug. Start engine with
choke/throttle lever in
FAST position.
4. Take engine to an
authorized Honda
Fuel filter clogged, carburetor Replace or repair faulty
malfunction, ignition
malfunction, valves stuck,
etc.
components as necessary.
servicing dealer, or
refer to shop manual.
Oxygenated Fuels
Some conventional gasolines are being blended with alcohol or an
ether compound. These gasolines are collectively referred to as
oxygenated fuels. To meet clean air standards, some areas of the
United States and Canada use oxygenated fuels to help reduce
emissions.
ENGINE LACKS POWER
Possible Cause
Correction
1. Check air cleaner.
Filter elements clogged.
Clean or replace filter
elements (p. 6).
2. Check fuel.
Bad fuel; engine stored
without treating or draining
gasoline, of refueled with bad with fresh gasoline.
gasoline.
Drain the fuel tank and
carburetor (p. 8). Refuel
If you use oxygenated fuel, be sure it is unleaded and meets the
minimum octane rating requirements.
3. Take engine to an
authorized Honda
Fuel filter clogged, carburetor Replace or repair faulty
malfunction, ignition
malfunction, valves stuck,
etc.
components as necessary.
Before using an oxygenated fuel, try to confirm the fuel’s contents.
Some states/provinces require this information to be posted on the
pump.
servicing dealer, or
refer to shop manual.
TECHNICAL & CONSUMER INFORMATION
The following are the EPA approved percentages of oxygenates:
TECHNICAL INFORMATION
Serial Number Location
ETHANOL — (ethyl or grain alcohol) 10% by volume
You may use gasoline containing up to 10% ethanol
by volume. Gasoline containing ethanol may be
marketed under the name Gasohol.
Record the engine serial number and type in the space below. You will
need this information when ordering parts and when making technical
or warranty inquiries.
MTBE
— (methyl tertiary butyl ether) 15% by volume
You may use gasoline containing up to 15% MTBE
by volume.
SERIAL NUMBER AND
TYPE LOCATION
METHANOL — (methyl or wood alcohol) 5% by volume
You may use gasoline containing up to 5%
methanol by volume as long as it also contains
cosolvents and corrosion inhibitors to protect the
fuel system. Gasoline containing more than 5%
methanol by volume may cause starting and/or
performance problems. It may also damage metal,
rubber, and plastic parts of your fuel system.
If you notice any undesirable operating symptoms, try another service
station or switch to another brand of gasoline.
SERIALNUMBER TYPE
Fuel system damage or performance problems resulting from the use
of an oxygenated fuel containing more than the percentages of
oxygenates mentioned above are not covered under the Distributor’s
Limited Warranty (see page 11).
MODEL
SERIAL NUMBER
ENGINE TYPE
GXV160
GJ03– ___ ___ ___ ___ ___ ___ ___
___ ___ ___ ___
9
Emission Control System Information
Source of Emissions
Air Index
An Air Index Information hang tag/label is applied to engines certified
to an emission durability time period in accordance with the
requirements of the California Air Resources Board.
The combustion process produces carbon monoxide, oxides of
nitrogen, and hydrocarbons. Control of hydrocarbons and oxides of
nitrogen is very important because, under certain conditions, they
react to form photochemical smog when subjected to sunlight. Carbon
monoxide does not react in the same way, but it is toxic.
The bar graph is intended to provide you, our customer, the ability to
compare the emissions performance of available engines. The lower
the Air Index, the less pollution.
Honda utilizes lean carburetor settings and other systems to reduce
the emissions of carbon monoxide, oxides of nitrogen, and
hydrocarbons.
The durability description is intended to provide you with information
relating the engine’s emission durability period. The descriptive term
indicates the useful life period for the engine’s emission control
system. See your Emission Control System Warranty (page 11) for
The U.S. and California Clean Air Acts
additional information.
EPA and California regulations require all manufacturers to furnish
written instructions describing the operation and maintenance of
emission control systems.
Descriptive Term
Moderate
Applicable to Emissions Durability Period
50 hours (0–65 cc)
125 hours (greater than 65 cc)
The following instructions and procedures must be followed in order to
keep the emissions from your Honda engine within the emission
standards.
Intermediate
Extended
125 hours (0–65 cc)
250 hours (greater than 65 cc)
300 hours (0–65 cc)
Tampering and Altering
500 hours (greater than 65 cc)
Tampering with or altering the emission control system may increase
emissions beyond the legal limit. Among those acts that constitute
tampering are:
The Air Index Information hang tag/label must remain on the engine
until it is sold. Remove the hang tag before operating the engine.
Specifications
• Removal or alteration of any part of the intake, fuel, or exhaust
systems.
Length x Width x Height
16.3 x 14.1 x 13.9 in
(415 x 359 x 354 mm)
• Altering or defeating the governor linkage or speed-adjusting
mechanism to cause the engine to operate outside its design
parameters.
Dry weight
32.6 lb (14.8 kg)
32.1 lb (14.6 kg)
Engine type
4-stroke, overhead valve, single cylinder
9.9 cu in (163 cm3)
[2.7 x 1.8 in (68 x 45 mm)]
Problems That May Affect Emissions
Displacement
[Bore x Stroke]
If you are aware of any of the following symptoms, have your engine
inspected and repaired by your servicing dealer.
Maximum output
Maximum torque
Fuel consumption
Cooling system
Ignition system
5.5 bhp at 3,600 rpm
7.59 ft-lb (1.05 kg/m) at 2,500 rpm
0.56 lb/hph (340 g/kWh)
Forced air
• Hard starting or stalling after starting.
• Rough idle.
• Misfiring or backfiring under load.
• Afterburning (backfiring).
Transistorized magneto
Counterclockwise
PTO shaft rotation
• Black exhaust smoke or high fuel consumption.
Replacement Parts
Tuneup Specifications
The emission control systems on your Honda engine were designed,
built, and certified to conform with EPA and California emission
regulations. We recommend the use of genuine Honda parts
whenever you have maintenance done. These original-design
replacement parts are manufactured to the same standards as the
original parts, so you can be confident of their performance. The use of
replacement parts that are not of the original design and quality may
impair the effectiveness of your emission control system.
ITEM
SPECIFICATION
MAINTENANCE
Spark plug gap
0.028 – 0.031 in (0.7 – 0.8 mm) Refer to page 6.
Valve clearance
(cold)
IN: 0.15 ± 0.04 mm
EX: 0.20 ± 0.04 mm
See your authorized
Honda dealer
Other specifications
No other adjustments needed.
A manufacturer of an aftermarket part assumes the responsibility that
the part will not adversely affect emission performance. The
manufacturer or rebuilder of the part must certify that use of the part
will not result in a failure of the engine to comply with emission
regulations.
Maintenance
Follow the maintenance schedule on page 4. Remember that this
schedule is based on the assumption that your machine will be used
for its designed purpose. Sustained high-load or high-temperature
operation, or use in unusually wet or dusty conditions, will require
more frequent service.
10
Emission Control System Warranty
CONSUMER INFORMATION
Your new Honda Power Equipment engine complies with both the U.S. EPA and State of
California emission regulations. American Honda provides the same emission warranty
coverage for engines sold in all 50 states.
Honda Publications
These publications will give you additional information for maintaining
and repairing you engine.You may order them from an authorized
Honda engine servicing dealer.
Your Warranty Rights And Obligations:
California
The California Air Resources Board and American Honda Motor Co., Inc. are pleased to
explain the emission control system warranty on your Honda Power Equipment engine. In
California, new utility and lawn and garden equipment engines must be designed, built and
equipped to meet the State's stringent anti-smog standards.
Shop Manual
This manual covers complete maintenance and overhaul
procedures. It is intended to be used by a skilled
technician.
Other States
In other areas of the United States your engine must be designed, built, and equipped to
meet the U.S. EPA emission standards for spark-ignited engines at or below 19 kilowatts.
Parts Catalog
This manual provides complete, illustrated parts lists.
All States
Distributor’s Limited Warranty
American Honda Motor Co., Inc. must warrant the emission control system on your power
equipment engine for the period of time listed below provided there has been no abuse,
neglect or improper maintenance of your power equipment engine. Where a warrantable
condition exists, American Honda Motor Co., Inc. will repair your power equipment engine
at no cost to you including diagnosis, parts and labor.
PRODUCTS COVERED BY THIS
WARRANTY:
LENGTH OF WARRANTY:
(FROM DATE OF ORIGINAL
PURCHASE)
Your emission control system may include such parts as the carburetor or fuel injection
system, the ignition system, and catalytic converter. Also included may be hoses,
connectors and other emission-related assemblies.
PRODUCT
APPLICATIONS
NONCOMMERCIAL/ COMMERCIAL/
NONRENTAL
RENTAL
GXV Series
Engines
ALL (1)
24 months
24 months
Manufacturer's Warranty Coverage:
The 1995 and later power equipment engines are warranted for two years. If any emission-
related part on your engine is defective, the part will be repaired or replaced by American
Honda Motor Co., Inc.
(1) Honda GXV series general purpose engines have a 3 months warranty period when
installed on concession type vehicles.
Owner's Warranty Responsibility:
To Qualify for this Warranty:
As the power equipment engine owner, you are responsible for the performance of the
required maintenance listed in your owner's manual. American Honda Motor Co., Inc.
recommends that you retain all receipts covering maintenance on your power equipment
engine, but American Honda Motor Co., Inc. cannot deny warranty coverage solely for the
lack of receipts or for your failure to ensure the performance of all scheduled maintenance.
The Honda general purpose engine must be purchased from a Honda general purpose
engine dealer or distributor authorized to sell that product in the United States, Puerto Rico,
or the U.S. Virgin Islands. This limited warranty applies to first retail purchaser and each
subsequent owner during the applicable warranty time period.
What American Honda Will Repair or Replace Under Warranty:
As the power equipment engine owner, you should however be aware that American
Honda Motor Co., Inc. may deny you warranty coverage if your power equipment engine or
a part has failed due to abuse, neglect, improper maintenance, or unapproved
modifications.
American Honda will repair or replace, at its option, any part that is proven to be defective
in material or workmanship under normal use during the applicable warranty time period.
Warranty repairs and replacements will be made without charge for parts or labor. Anything
replaced under warranty becomes the property of American Honda Motor Company, Inc.
All parts replaced under warranty will be considered as part of the original product and any
warranty on those parts will expire coincident with the original product warranty.
You are responsible for presenting your power equipment engine to a Honda Power
Equipment dealer as soon as a problem exists. The warranty repairs should be completed
in a reasonable amount of time, not to exceed 30 days.
To Obtain Warranty Service:
If you have any questions regarding your warranty rights and responsibilities, you should
write or call the Honda Power Equipment Customer Relations Department. Refer to
page 12 for contact information.
You must take your Honda general purpose engine, or the equipment in which it is
installed, together with proof of original retail purchase date, at your expense, to a Honda
engine dealer or distributor authorized to sell that product in the United States, Puerto Rico,
or the U.S. Virgin Islands, during their normal business hours. Many Honda engine dealers
and distributors are listed in the yellow pages of the telephone directory under gasoline
engines, lawn & garden equipment & supplies, etc.
Warranty Coverage:
Honda power equipment engines manufactured after January 1, 1995 and sold in the State
of California, and U.S. EPA certified engines manufactured on or after September 1, 1996
and sold in all of the United States, are covered by this warranty for a period of two years
from the date of delivery to the original retail purchaser. This warranty is transferable to
each subsequent purchaser for the duration of the warranty period.
If you are unable to obtain warranty service, or are dissatisfied with the warranty service
you receive, take the following steps: First contact the owner of the dealership or distributor
involved. Normally this should resolve the problem. However, if you are dissatisfied with
the decision made by the dealership's management, contact the Honda Regional Engine
Distributor for your area. You can find their name, address, and phone number using the
426-7701. If you are still dissatisfied after speaking with the Regional Engine Distributor,
you may contact the Honda Power Equipment Customer Relations Department of
American Honda Motor Co., Inc. Refer to page 12 for contact information.
Warranty repairs will be made without charge for diagnosis, parts or labor. All defective
parts replaced under this warranty become the property of American Honda Motor Co., Inc.
A list of warranted parts is on the reverse side of this warranty statement. Normal
maintenance items, such as spark plugs and filters, that are on the warranted parts list are
warranted up to their required replacement interval only.
American Honda Motor Co., Inc. is also liable for damages to other engine components
caused by a failure of any warranted part during the warranty period.
Exclusions:
THIS WARRANTY DOES NOT EXTEND TO PARTS AFFECTED OR DAMAGED BY THE
PRODUCT IN WHICH THE ENGINE IS INSTALLED, OR BY ACCIDENT AND/OR
COLLISION, MISUSE, NEGLECT, PARTS WORN BEYOND SERVICE LIMITS DUE TO
NORMAL WEAR/NORMAL SERVICE LIFE, PARTS AFFECTED OR DAMAGED BY THE
CONVERSION TO OR USE OF FUEL OTHER THAN THE FUEL(S) WHICH THE
ENGINE IS ORIGINALLY MANUFACTURED TO USE, POOR OPERATION RELATED TO
FUEL CONTAMINATION OR FUEL QUALITY, PARTS DAMAGED BY FUEL
CONTAMINATION, THE INCORPORATION OF, OR USE OF, UNSUITABLE
ATTACHMENTS OR PARTS, THE UNAUTHORIZED ALTERATION OF ANY PART OR
ANY CAUSES OTHER THAN DEFECTS IN MATERIAL OR WORKMANSHIP OF THE
ENGINE. USE OF THE HONDA GENERAL PURPOSE ENGINE FOR RACING OR
COMPETITION WILL VOID THIS WARRANTY.
Only Honda approved replacement parts may be used in the performance of any warranty
repairs and must be provided without charge to the owner. The use of replacement parts
not equivalent to the original parts may impair the effectiveness of your engine emission
control system. If such a replacement part is used in the repair or maintenance of your
engine, and an authorized Honda dealer determines it is defective or causes a failure of a
warranted part, your claim for repair of your engine may be denied. If the part in question is
not related to the reason your engine requires repair, your claim will not be denied.
To Obtain Warranty Service:
You must take your Honda Power Equipment engine or the product on which it is installed,
along with your warranty registration card or other proof of original purchase date, at your
expense, to any Honda Power Equipment dealer who is authorized by American Honda
Motor Co., Inc. to sell and service that Honda product during his normal business hours.
Claims for repair or adjustment found to be caused solely by defects in material or
workmanship will not be denied because the engine was not properly maintained and
used.
Disclaimer of Consequential Damage and Limitation of Implied Warranties:
AMERICAN HONDA DISCLAIMS ANY RESPONSIBILITY FOR LOSS OF TIME OR USE
OF THE ENGINE, OR THE EQUIPMENT IN WHICH THE ENGINE IS INSTALLED,
TRANSPORTATION, COMMERCIAL LOSS, OR ANY OTHER INCIDENTAL OR
CONSEQUENTIAL DAMAGE. ANY IMPLIED WARRANTIES ARE LIMITED TO THE
DURATION OF THIS WRITTEN LIMITED WARRANTY. Some states do not allow
limitations on how long an implied warranty lasts and/or do not allow the exclusion or
limitation of incidental or consequential damages, so the above exclusions and limitations
may not apply to you.
If you are unable to obtain warranty service, or are dissatisfied with the warranty service
you receive, see To Obtain Warranty Service on page 12.
This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state.
11
Exclusions:
Distributor/Dealer Locator Information
FAILURES OTHER THAN THOSE RESULTING FROM DEFECTS IN MATERIAL OR
WORKMANSHIP ARE NOT COVERED BY THIS WARRANTY. THIS WARRANTY DOES
NOT EXTEND TO EMISSION CONTROL SYSTEMS OR PARTS WHICH ARE
AFFECTED OR DAMAGED BY OWNER ABUSE, NEGLECT, IMPROPER
MAINTENANCE, MISUSE, MISFUELING, IMPROPER STORAGE, ACCIDENT AND/OR
COLLISION, THE INCORPORATION OF, OR ANY USE OF, ANY ADD-ON OR MODIFIED
PARTS, UNSUITABLE ATTACHMENTS, OR THE UNAUTHORIZED ALTERATION OF
ANY PART.
To find an Authorized Honda Engine Distributor/Dealer anywhere in
the United States:
Call (800) 426-7701
or visit our website: www.honda-engines.com
Customer Service Information
THIS WARRANTY DOES NOT COVER REPLACEMENT OF EXPENDABLE
MAINTENANCE ITEMS MADE IN CONNECTION WITH REQUIRED MAINTENANCE
SERVICES AFTER THE ITEM'S FIRST SCHEDULED REPLACEMENT AS LISTED IN
THE MAINTENANCE SECTION OF THE PRODUCT OWNER'S MANUAL, SUCH AS:
SPARK PLUGS AND FILTERS.
Servicing dealership personnel are trained professionals. They should
be able to answer any questions you may have. If you encounter a
problem that your dealer does not solve to your satisfaction, please
discuss it with the dealership's management. The Service Manager,
General Manager, or Owner can help. Almost all problems are solved
in this way.
Disclaimer of Consequential Damage and Limitation of Implied Warranties:
AMERICAN HONDA MOTOR CO., INC. DISCLAIMS ANY RESPONSIBILITY FOR
INCIDENTAL OR CONSEQUENTIAL DAMAGES SUCH AS LOSS OF TIME OR THE USE
OF THE POWER EQUIPMENT, OR ANY COMMERCIAL LOSS DUE TO THE FAILURE
OF THE EQUIPMENT; AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE
DURATION OF THIS WRITTEN WARRANTY. THIS WARRANTY IS APPLICABLE ONLY
WHERE THE CALIFORNIA OR U.S. EPA EMISSION CONTROL SYSTEM WARRANTY
REGULATION IS IN EFFECT.
If you are dissatisfied with the decision made by the dealership's
management, contact the Honda Regional Engine Distributor for your
area. You can find their name, address, and phone number using the
dealer/distributor locator on our website at (www.honda-engines.com)
or by calling 1-800-426-7701.
Emission Control System Warranty Parts:
SYSTEMS COVERED
BY THIS WARRANTY:
PARTS
DESCRIPTION:
If you are still dissatisfied after speaking with the Regional Engine
Distributor, you may contact the Honda Power Equipment Customer
Relations Office. You can write to:
Carburetor assembly, Fuel injection pump,
Fuel injection nozzle, Fuel regulator
Fuel Metering
Exhaust
Catalyst
American Honda Motor Co., Inc.
Power Equipment Division
Customer Relations Office
4900 Marconi Drive
Air filter housing, Air filter element*,
Crankcase breather tube
Air Induction
Flywheel magneto, Ignition pulse generator,
Ignition coil assembly, Ignition control
module, Spark plug cap, Spark plug*
Alpharetta, GA 30005-8847
Ignition
Or telephone: (770) 497-6400, 8:30 am - 6:00 pm EST
When you write or call, please give us this information:
Tubing, fittings, seals, gaskets, and clamps
associated with these listed systems.
Miscellaneous Parts
* Covered up to the first required replacement only.
See the Maintenance Schedule on page 4.
• Equipment manufacturer’s name and model number that the
engine is mounted on
• Engine model, serial number, and type (see page 9)
• Name of dealer who sold the engine to you
• Name, address, and contact person of dealer who services your
engine
• Name of Distributor you contacted and the contact person
• Date of purchase
• Your name, address and telephone number
• A detailed description of the problem
12
|