FP260 series
before using your Kenwood appliance
Read these instructions carefully and retain for future reference.
Remove all packaging and any labels.
Important – UK only
G
G
G
The wires in the cord are coloured as follows:
Green and Yellow = Earth,
Blue = Neutral,
Brown = Live.
safety
G
G
G
The appliance must be protected by a 13A approved (BS1362)
fuse.
WARNING: THIS APPLIANCE MUST BE EARTHED.
Note:
For non-rewireable plugs the fuse cover MUST be refitted when
replacing the fuse. If the fuse cover is lost then the plug must not
be used until a replacement can be obtained. The correct fuse
cover is identified by colour and a replacement may be obtained
from your Kenwood Authorised Repairer (see Service).
If a non-rewireable plug is cut off it must be DESTROYED
IMMEDIATELY. An electric shock hazard may arise if an
unwanted non-rewireable pug is inadvertently inserted into a 13A
socket outlet.
G
The blades and discs are very sharp, handle with care. Always
hold the knife blade by the finger grip at the top,
away from the cutting edge, both when handling and
cleaning.
G
G
G
Always remove the knife blade before pouring contents from the
bowl.
Keep hands and utensils out of the processor bowl and liquidiser
goblet whilst connected to the power supply.
Switch off and unplug:-
G
G
G
before fitting or removing parts;
G
when not in use;
G
before cleaning.
G
G
Never use your fingers to push food down the feed tube. Always
use the pusher/s supplied.
Before removing the lid from the bowl or liquidiser/mill from the
power unit:-
This appliance conforms to EC directive 2004/108/EC on
Electromagnetic Compatibility and EC regulation no. 1935/2004
of 27/10/2004 on materials intended for contact with food.
G
before using for the first time
switch off;
G
1 Remove all packaging including the plastic blade covers from the
knife blade. Take care the blades are very sharp. These
covers should be discarded as they are to protect the blade
during manufacture and transit only.
wait until the attachment/blades have completely stopped;
be careful not to unscrew the liquidiser goblet or mill jar from
the blade assembly.
G
G
G
G
Liquids should be allowed to cool to room temperature before
blending.
2 Wash the parts see ‘cleaning’
3 Push excess cord into the back of the machine.
Do not use the lid to operate the processor, always use the on/off
speed control.
This machine will be damaged and may cause injury
if the interlock mechanism is subjected to excessive
force.
G
G
G
Never use an unauthorised attachment.
Never leave the appliance unattended when it is operating.
Never use a damaged appliance. Get it checked or repaired: see
‘service and customer care’.
G
G
Never let the power unit, cord or plug get wet.
Don’t let excess cord hang over the edge of a table or worktop
or touch hot surfaces.
G
G
Do not exceed the maximum capacities stated in the
recommended speed chart.
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a
person responsible for their safety.
G
G
Children should be supervised to ensure that they do not play
with the appliance.
Only use the appliance for its intended domestic use. Kenwood
will not accept any liability if the appliance is subject to improper
use, or failure to comply with these instructions.
Misuse of your processor/liquidiser can result in injury.
G
G
Refer to the relevant section under “using the attachments” for
additional safety warnings for each individual attachment.
before plugging in
Make sure your electricity supply is the same as the one shown
on the underside of your machine.
2
important
key
G
G
Your processor bowl is not suitable for crushing or grinding
coffee beans, or converting granulated sugar to caster sugar.
When adding almond essence or flavouring to mixtures avoid
contact with the plastic as this may result in permanent marking.
processor
ቢ pusher
ባ feed tube
ቤ lid
ብ bowl
to use your liquidiser
1 Fit the sealing ring ቭ into the blade unit ቫ - ensuring the seal is
located correctly. Leaking will occur if the seal is
damaged or not fitted correctly.
2 Screw the goblet onto the blade assembly ᕤ.
The liquidiser will not work if incorrectly assembled.
3 Put your ingredients into the jug.
ቦ detachable drive shaft
ቧ speed + pulse control
ቨ power unit
ቩ safety interlock
ቪ cord storage
4 Fit the lid to the goblet and push down to secure ᕥ. Fit the filler
cap.
glass liquidiser
ቫ blade unit
ቭ sealing ring
ቮ goblet
5 Place the liquidiser onto the power unit and turn clockwise to
lock ᕧ.
6 Select a speed or use the pulse control.
ቯ lid
ተ filler cap
safety
G
Liquids should be allowed to cool to room
temperature before blending.
Always take care when handling the blade assembly and avoid
touching the cutting edge of the blades when cleaning.
Only operate the liquidiser with the lid in place.
glass mill
ቱ jar
G
G
G
Only use the goblet with the blade assembly supplied.
Never run the liquidiser empty.
To ensure the long life of your liquidiser, do not run it for longer
than 60 seconds.
attachments
ቲ knife blade
G
G
ታ dough tool
ቴ twin beater geared whisk
ት thick slicing/coarse shredding disc
ቶ thin slicing/fine shredding disc
rasping disc
G
Smoothie recipes - never blend frozen ingredients that have
formed a solid mass during freezing, break it up before adding to
the goblet.
hints
geared citrus press (if supplied)
G
When making mayonnaise, put all the ingredients, except the oil,
into the liquidiser. Remove the filler cap. Then, with the appliance
running, add the oil slowly through the hole in the lid.
Thick mixtures, e.g. pâtés and dips, may need scraping down. If
the mixture is difficult to process, add more liquid.
Ice crushing - operate the pulse in short bursts until crushed to the
desired consistency.
The processing of spices is not recommended as they may
damage the plastic parts.
The appliance will not work if the liquidiser is incorrectly fitted.
to use your food processor
1 Fit the detachable shaft onto the power unit ᕡ.
2 Then fit the bowl. Place the handle towards the back and turn
clockwise until it locks ᕢ.
G
G
3 Fit an attachment over the drive shaft.
G
G
Always fit the bowl and attachment onto the machine before
adding ingredients.
4 Fit the lid ᕣ - ensuring the top of the drive shaft locates into the
centre of the lid.
G
G
To blend dry ingredients - cut into pieces, remove the filler cap,
then with the appliance running, drop the pieces down one by
one. Keep your hand over the opening. For best results empty
regularly.
Don’t use the liquidiser as a storage container. Keep it empty
before and after use.
G
Do not use the lid to operate the processor, always
use the on/off speed control.
5 Switch on and select a speed.
G
G
The processor won’t work if the bowl and lid are
fitted incorrectly.
Use the pulse control for short bursts. The pulse will operate as
long as the control is held in position.
G
Never blend more than 1.2 litres - less for frothy liquids like
milkshakes.
G
6 Reverse the above procedure to remove the lid, attachments and
bowl.
G
Always switch off before removing the lid.
3
G
G
Never remove the mill until the blades have completely stopped.
To ensure the long life of your mill, never run for longer than
30 seconds. Switch off as soon as you have got the right
consistency.
The processing of spices is not recommended as they may
damage the plastic parts.
to use your mill
Use the mill for milling herbs, nuts and coffee beans.
1 Put the ingredients into the jar ቱ.
G
2 Fit the sealing ring ቭ into the blade unit ቫ.
3 Turn the blade unit upside down. Lower it into the jar, blades
down.
4 Screw the blade unit onto the jar until finger tight ᕦ.
5 Place the mill onto the power unit and turn clockwise to lock ᕧ.
6 Switch onto maximum speed or use the pulse control.
G
G
The appliance will not work if the mill is incorrectly fitted.
Use for dry ingredients only.
hints
Herbs are best milled when clean and dry.
safety
G
Never fit the blade unit to your food processor without the jar
fitted.
G
Never unscrew the jar while the mill is fitted to your appliance.
G
Do not touch the sharp blades – Keep the blade unit away from
children.
recommended speed chart
tool/attachment
function
speed
maximum
capacities
knife blade
Cake making
1 – 2
2
1Kg/2lb 4oz total weight
250g/9oz flour weight
Rubbing fat into flour
Adding water to combine pastry ingredients
Chopping & pureeing
1 – 2
2
400g/14oz chopping lean
meat total weight
1 litre
Thick soup mixes (500mls liquid to 500g dry
ingredients)
1 – 2
Thinner soup mixes/milk
yeasted mixes
1 – 2
600 ml
dough tool
whisk
2
340g/12oz flour weight
Egg whites
2
4
Cream
1 – 2
250 ml
discs - slicing/shredding
rasping disc
Firm food items such as carrots, hard cheeses
Softer items such as cucumbers, tomatoes
Parmesan cheese, Potato for German
potato dumplings
2
1
2
–
–
–
citrus press
liquidiser
mill
Citrus fruits
All processing
1
2
2
2
–
1.2 litres
10g
50g
Herbs
Nuts and Coffee Beans
4
using the attachments
see chart above for speed of each attachment.
slicing/shredding discs
To use the discs.
reversible slicing/shredding discs - thick ት, thin ቶ
Use the shredding side for cheese, carrots, potatoes and foods
of a similar texture.
Use the slicing side for cheese, carrots, potatoes, cabbage,
cucumber, courgette, beetroot and onions.
ቲ knife blade/ታ dough tool
The knife blade is the most versatile of all the attachments. The
length of the processing time will determine the texture achieved.
For coarser textures use the pulse control.
rasping disc
Grates Parmesan cheese and potatoes for German potato
dumplings.
Use the knife blade for cake and pastry making, chopping raw
and cooked meat, vegetables, nuts, pate, dips, pureeing soups
and to also make crumbs from biscuits and bread.
Use the dough tool for yeasted mixes.
safety
hints
knife blade
Cut food such as meat, bread, vegetables into cubes
approximately 2cm/3/4in before processing.
G
Never remove the lid until the cutting disc has
completely stopped.
G
G
Handle the cutting discs with care - they are
extremely sharp
G
Biscuits should be broken into pieces and added down the feed
tube whilst the machine is running.
When making pastry use fat straight from the fridge cut into
2cm/3/4in.cubes.
Take care not to over-process.
to use the cutting discs
1 Fit the drive shaft and bowl onto the power unit.
2 Holding by the centre grip, place the disc onto the drive shaft with
the appropriate side uppermost.
3 Fit the lid.
4 Put the food in the feed tube.
G
G
dough tool
G
Place the dry ingredients in the bowl and add the liquid down the
feed tube whilst the machine is running. Process until a smooth
elastic ball of dough is formed this will take 60 secs.
Re-knead by hand only. Re-kneading in the bowl is not
recommended as it may cause the processor to become unstable.
5 Switch on and push down evenly with the pusher - never put
your fingers in the feed tube.
G
hints
G
ቴ twin beater geared whisk
Use fresh ingredients
Don’t cut food too small. Fill the width of the feed tube fairly full.
This prevents the food from slipping sideways during processing.
Food placed upright comes out shorter than food placed
G
Use for light mixtures only eg egg whites, cream, evaporated
milk and for whisking eggs and sugar for fatless sponges.
Heavier mixtures such as fat and flour will damage it.
G
horizontal.
G
using the whisk
1 Fit the drive shaft and bowl onto the power unit.
There will always be a small amount of waste on the disc or in
the bowl after processing.
2 Push each beater securely into the drive head.
3 Fit the whisk by carefully turning until it drops over the drive
shaft.
4 Add the ingredients.
5 Fit the lid - ensuring the end of the shaft locates into the centre
citrus press (if supplied)
Use the citrus press to squeeze the juice from citrus fruits (eg
oranges, lemons, limes and grapefruits).
cone
sieve
of the lid.
6 Switch on.
important
to use the citrus press
G
The whisk is not suitable for making one-stage cakes
or creaming fat and sugar as these mixes will
damage it. Always use the knife blade for cake
making.
1 Fit the drive shaft and bowl onto the power unit.
2 Fit the sieve into the bowl - ensuring the sieve handle is locked
into position directly over the bowl handle.
3 Place the cone over the drive shaft turning until it drops all the
way down.
hints
G
Best results are obtained when the eggs are at room
4 Cut the fruit in half. Then switch on and press the fruit onto the
cone.
temperature.
G
Ensure the bowl and whisks are clean and free from grease
before whisking.
G
The citrus press will not operate if the sieve is not
locked correctly.
5
care & cleaning
G
Always switch off and unplug before cleaning.
G
Handle the blades and cutting discs with care - they are
extremely sharp.
G
Some foods may discolour the plastic. This is perfectly normal
and won’t harm the plastic or affect the flavour of your food. Rub
with a cloth dipped in vegetable oil to remove the discolouration.
IMPORTANT INFORMATION FOR CORRECT DISPOSAL
OF THE PRODUCT IN ACCORDANCE WITH EC
DIRECTIVE 2002/96/EC.
At the end of its working life, the product must not be disposed of as
urban waste.
power unit
G
Wipe with a damp cloth, then dry. Ensure that the interlock area
is clear of food debris.
It must be taken to a special local authority differentiated waste
collection centre or to a dealer providing this service.
Disposing of a household appliance separately avoids possible
negative consequences for the environment and health deriving
from inappropriate disposal and enables the constituent materials
to be recovered to obtain significant savings in energy and
resources. As a reminder of the need to dispose of household
appliances separately, the product is marked with a crossed-out
wheeled dustbin.
G
Store excess cord in the storage area at the back of the machine
ቪ.
liquidiser/mill
1 Empty the goblet/jar before unscrewing it from the blade
assembly.
2 Wash the goblet/jar by hand.
3 Remove and wash the sealing ring.
4 Don’t touch the sharp blades – brush them clean using hot
soapy water, then rinse thoroughly under the tap. Don’t
immerse the blade unit in water.
5 Leave to dry upside down.
guarantee UK only
If your food processor goes wrong within one year from the date
you bought it, we will repair it (or replace it if necessary) free of
charge provided:
twin beater geared whisk
Detach the beaters from the drive head by gently pulling them
free. Wash in warm soapy water.
Wipe the drive head with a damp cloth, then dry. Do not
G
G
you have not misused, neglected, or damaged it;
G
it has not been modified (unless by Kenwood);
G
G
it is not second hand;
immerse the drive head in water.
G
it has not been used commercially;
bowl/lid and attachments
Wash by hand, then dry.
Alternatively they can be washed on the top rack of your
dishwasher. A short low temperature program is recommended.
G
you have not fitted a plug incorrectly; and
G
G
you supply your receipt to show when you bought it.
G
This guarantee does not affect your statutory rights.
service and customer care
G
If the cord is damaged it must, for safety reasons, be replaced
by Kenwood or an authorised Kenwood repairer.
UK
If you need help with:
G
Using your machine
G
Servicing or repairs (in or out of guarantee)
టcall Kenwood on 023 92392333 and ask for customer care.
Have your model number ready - it’s on the underside of
the processor.
G
spares and attachments
టcall 0844 557 3653.
other countries
Contact the shop where you brought the food processor.
G
Designed and engineered by Kenwood in the UK.
G
Made in China.
6
recipes
victoria sandwich
shortcrust pastry
250g (9oz) plain flour
150g (6oz) Soft margarine
150g (6oz) caster sugar
150g (6oz) self raising flour
5mls (1tsp) baking powder
3 eggs
125g (5oz) mixture of lard and margarine cut into small pieces
1
2.5 mls ( ⁄2 tsp) salt
45mls (3tbsp) cold water
15mls (1tbsp) warm water
filling & decoration
3tbsp strawberry jam
1 Fit the knife blade and add the flour, salt and fat. Process for
approximately 10 seconds or until the mixture looks like coarse
breadcrumbs.
1
150mls ( ⁄4pt) double cream whipped (optional)
2 Then add the water down the feed tube until the mixture looks
like it is about to stick together.
3 Turn out the mixture onto a worksurface and shape by hand.
Use as required.
1tbsp icing sugar or caster sugar
1 Pre-heat the oven to 180°C/350°F/Gas mark 4 and grease two
18cm(7”) shallow cake tins.
2 Fit the knife blade. Place all the ingredients for the sponge in the
bowl and process for 5 seconds. Using a spatula, scrape the
mixture into the centre of the bowl and process for a further 5
seconds.
G
For best results allow the pastry to rest before use. Place in a
plastic bag or wrap in clingfilm and chill in the fridge for 20
minutes.
3 Pour the mixture into the prepared tins and bake for 20-25
minutes or until firm to a light touch and coming away from the
edges slightly. If you are unsure whether the cake is cooked
insert a thin skewer in the centre and it should come out clean.
Turn out onto a wire cooling rack.
lasagne
300g (12oz) braising steak, cubed.
400g can of tomatoes
30mls (2tbsp) tomato puree
1 onion
4 When cool spread the jam and cream over one of the cakes,
top with the other cake and sprinkle with the sugar.
5mls (1tsp) basil
100g (4oz) lasagne
200g (8oz) mozzarella cheese
15mls (1tbsp) oil
salt and pepper
fruit cake
125g (5oz) block margarine (cut into cubes)
125g (5oz) caster sugar
2 eggs
80 - 100mls (5-6tbsp) milk
275g (11oz) mixed fruit
200g (8oz) self raising flour
5mls (1tsp) mixed spice
1 Grate the cheese using the shredding disc.
2 Then separately chop the meat and onions with the knife blade.
3 Pre-heat the oil and fry the onions until softened, add the meat
and fry until brown.
4 Then add the tomatoes, tomato puree and seasonings.
5 Stir well, cover and simmer gently for about 40minutes.
6 Cook the lasagne in plenty of salted boiling water until tender.
Then drain well.
7 Place layers of meat, lasagne and cheese in a 1litre/2pint oven
proof dish. Finish with a layer of cheese.
8 Bake at 190°C/375°F/Gas Mark 5 for 30minutes or until golden
and bubbling.
1 Fit the knife blade and place the cubed margarine and sugar in
the bowl.
2 Mix until smooth, light and fluffy, scraping down as necessary.
3 Add the eggs one at a time.
4 Add the flour, spices and milk. Pulse until ingredients combined.
5 Add the fruit using the pulse.
6 Pour the mixture into a greased and lined 7”/18cm round cake
tin. Bake in a preheated oven 150°C/300°F/Gas Mark 2 for
approximately 2 hours or until cooked. Turn out of the tin when
cool.
7
white bread
300g(10oz) strong white bread flour
5mls (1tsp) salt
1
6g( ⁄4oz) lard
1
15g ( ⁄2oz) fresh yeast or 10mls(2tsp) dried yeast + 5mls (1tsp)
caster sugar.
175mls (6 fl oz) warm water
1 Dried yeast (the type that needs reconstituting): Add
the yeast and sugar to the warm water. Leave to stand for 5 - 10
minutes until frothy.
Fresh yeast: crumble into the flour
Other types of yeast: follow the manufacturer’s instructions.
2 Fit the dough tool or knife blade and add the flour (with fresh
yeast if used), salt and lard. Process for a few seconds to evenly
distribute the ingredients.
3 Then with the motor running quickly pour the liquid in a steady
stream down the feed tube until the mixture forms an elastic soft
dough. This will take about 60 - 90 seconds.
4 Remove the dough, place in a bowl, cover with an oiled piece of
clingfilm or a plastic bag, and leave in a warm place for 45 - 60
minutes or until doubled in size.
5 Re-knead by hand for 2 - 3 minute. Re-kneading in the
bowl is not recommended as it may cause the
processor to become unstable. Shape into a loaf or 15
rolls and place on greased baking trays and leave until double in
size.
6 Then bake in a pre-heated oven at 230°C/450°F/Gas mark 8 for
20 - 25 minutes for the loaf or 10 - 15 minutes for bread rolls.
When ready they should sound hollow when tapped on the
base.
carrot and coriander soup
25g (1oz) butter
1 onion chopped
1 clove garlic crushed
590g carrot cut into 1 cm cubes
cold chicken stock
10-15ml (2-3tsp) ground coriander
salt and pepper
1 Melt the butter in a pan, add the onion and garlic and fry until
soft.
2 Place the carrot into the liquidiser, add the onion and garlic. Add
sufficient stock to reach the 1.2L level marked on the goblet. Fit
the lid and filler cap.
3 Blend on maximum speed for 5 seconds for a coarse soup or
longer for a finer result.
4 Transfer the mixture to a saucepan, add the coriander and
seasoning and simmer the soup for 30 to 35 minutes or until
cooked.
5 Adjust the seasoning as necessary and add extra liquid if
required.
8
Head Office Address: Kenwood Limited, New Lane, Havant, Hampshire PO9 2NH, UK
Designed and engineered by Kenwood in the UK
19251/4
Made in China
|