User’s guide
EKWE / EKWH
Contents
Safety instructions ............................................................................... 4
An overview of your honeycomb cooktop ........................................... 5
Before using the appliance for the first time ....................................... 5
Using the cooking zones ....................................................................... 6
Switching the honeycomb cooktop on
The cooking levels
6
6
Automatic boost function
Residual heat indicators
7
8
Dual-circuit cooking zones
The pan-on detection
8
9
The emergency switch
10
10
11
11
12
12
Minute minder and switch-off function
Childproof lock (sensor lock)
Time limit function (holiday function)
Other functions
Selecting pots and pans
Cleaning and care ............................................................................... 13
What to do if trouble occurs... ............................................................ 14
After Sales Service .............................................................................. 15
Users Guide - EKWE/EKWH - USA
3
Safety instructions
• The cooktop must be built into a countertop opening! Do • Never flambé under the cooker hood. The fat in the filter
not use the appliance if it has not been installed!
can ignite!
• Be sure the appliance is properly installed and grounded • The connecting cable must not come in contact with the
by a qualified technician. hot cooking surface.
• The appliance may only be installed and connected to the • CAUTION: Overheated greases and oils may ignite
power supply, maintained, and repaired by a qualified
electrician in accordance with safety regulations. Do not
repair or replace any part of the appliance unless
specifically recommended in this manual. Work performed
incorrectly puts your safety at risk.
themselves. Prepare meals with greases and oils very
carefully and control the heat. Should fats or oils ignite,
do not use water to extinguish them! Smother the fire or
flame or use a dry chemical or foam-type extinguisher.
• Don’t switch the cooking surface on unless you’re using
it for cooking. Never use a cooking zone without a pot or
pan set on it. Never use the appliance to heat a room!
• Immediately switch off the cooking zone after using with
the respective minus key and not just by pot recognition.
• This appliance is for residential use only. Use for any other
purpose is at the owner's risk and could be dangerous.
The manufacturer can’t be held responsible for damage
caused by improper use of this appliance.
• Danger of burning! The cook top
becomes hot during operation.
CAUTION: Keep children away from this
appliance.
• CAUTION! Items of interest to children should not be
stored in cabinets above a cooktop. A child can be
seriously injured by climbing on a cooktop to reach them.
• Never leave the cooking surface unattended at high heat
settings. Boilover can cause smoking and greasy
spillovers that may ignite.
• Wear proper apparel. Loose-fitting or hanging garments
should not come in contact with the cooking surface. Dish
cloths, potholders and aprons should not be stored near
the surface units.
• Do not leave children alone or unattended in the area
where the appliance is in use. They should never be
allowed to sit or stand on any part of the appliance.
• Don’t touch the cooking surface or areas near it. The
cooking surface may be hot even though it’s dark in color.
Areas near it may become hot enough to cause burns.
During and after use, do not touch the surface, or let
clothing or other flammable materials come in contact
with it until it’s had time to cool.
• To reduce the risk of burns, ignition of flammable
materials, and spillage due to unintentional contact with
the untensil, the handle of an utensil should be positioned
so that it is turned inward, and does not extend over
adjacent surface units.
• Use only dry potholders. Moist or damp potholders on hot
surfaces may result in burns from steam. Do not let
potholder touch a hot surface. Do not use a towel or other
bulky cloth.
• Use the proper pan size. This appliance is equipped with
different sized surface units. Use flat-bottomed cookware
that is large enough to cover the surface unit heating
element. The use of undersized cookware will leave a
portion of the heating element exposed and direct contact
could result in the ignition of clothing. Using a proper
relationship between cookware and burners will also
improve efficiency. Review “Selecting pots and pans“ on
page 12.
• CAUTION! Only certain types of glass, glass/ceramic,
ceramic, earthenware, or other glazed utensils can be
used on the range-top without breaking, due to the
sudden change in temperature. Follow the manufacturer's
instructions!
• Do not place non-food items on the cooking surface when
it's hot.
• Be careful when working with attachments! The
connecting cord must not come in contact with the hot
cooking surface.
• Flammable materials should not be stored near surface
units.
Don’t put combustible or flammable objects on the • Do not put plastic on the cooking surface. Things that
cooking top. They could be ignited if the burners are
unintentionally turned on.
can melt (i.e. plastics, foils or sugar), must be kept away
from the cooking surface. Be sure to immediately
remove or lift off any melted item from the hot
cooking surface. Use the supplied cleaning scraper in
order to avoid damage to the cooking surface.
• Do not use aluminium foil to line the surface unit drip
bowls.
• The glass ceramic surface is very durable and can easily
withstand light to medium impacts and loads distributed
over large areas. Be sure to avoid concentrated loads (i.e.
• Clean and remove any burned-on materials. Don’t heat
these materials repeatedly.
spice bottles) from falling on the surface to avoid cracking • Lime deposits are harmful to the cooking surface.
or breaking of the cooking surface.
• If a wet sponge or cloth is used to wipe spills on a hot
• CAUTION! If the cooking surface becomes cracked or
fractured, quit using the appliance immediately.
Disconnect the power and call Customer Service. Cleaning
solutions and spills may penetrate the broken cooktop and
create a risk of electric shock.
cooking area, be careful to avoid steam burn. Some
cleaners can produce noxious fumes if applied to a hot
surface.
• Please follow the cleaning and maintenance instructions
carefully!
4
Users Guide - EKWE/EKWH - USA
An overview of your honeycomb cooktop
Cooking zones
Control honeycomb
The honeycomb cooktop is equipped with an easy-to-operate sensor control
system which is operated via the control honeycomb.
The layout of the cooking zones is shown in the control honeycomb. The
control honeycomb itself is not indicated.
The cooking zones can be activated by the touch of a fingertip on the control
honeycomb.
The control honeycomb consists of the following touch controls and sensors:
A and B Touch controls for the minute minder with plus and minus sensors
C
D
Minute minder with a control function
Touch controls for the cooking zones with plus and minus sensors
and, if required, additional sensors for dual-circuit cooking zones
E
F
Key sensor for the childproof lock
Off sensor
G
Stand-by sensor
Before using the appliance for the first time
– Before using the appliance the first time, be sure to clean the cooking
surface with a mixture of water and mild detergent on a clean cloth. Then
wipe the surface dry with a non-fluffy cloth.
Users Guide - EKWE/EKWH - USA
5
Using the cooking zones
Please note the safety instructions!
Subsequent to initial connection and after a power failure “'%0” will appear
briefly in the LED displays. Rotating, circling symbols will then be indicated.
This means that various sensors have been checked automatically and that
the touch sensitivity has also been newly set.
Touch the “off” sensor in order to confirm that there were no objects on the
cooking zones or on the sensors. These symbols will be switched off
immediately if there are no objects on the sensors. Otherwise remove any
objects and disconnect the cooking zone briefly from the mains (fuse) once
again.
Important!
There may not be any objects on the sensors or on the cooking zones while
the sensor sensitivity is automatically being set.
Switching the honeycomb cooktop on
Before you start to use a cooking zone, put the cook top into the stand-
by mode.
F
– Touch the stand-by sensor key for about 2 seconds. The touch controls
of the cooking zones will light up and the appliance will be ready for
operation (stand-by mode).
– Each cooking zone can now be operated individually.
Cooking zones on which a pan has been placed will indicate a small “u”.
The stand-by mode automatically switches itself off
– if no cooking zone is activated within 20 seconds (after 10 seconds an
acoustic buzzer will indicate that the appliance will switch off after another
10 seconds) or
– if it remains unused for one minute after operation.
The cooking levels
There exist 9 cooking levels.
The cooking setting required can be activated by means of the plus or the
minus sensor. It is shown in the display.
In order to be able to set a cooking level, a pan suitable for the pan-on
detection must have been placed on the cooking zone or the pan-on
detection must be deactivated.
F
or
F
The “0” setting remains visible for approx. 2 seconds after switch-off.
Cooking level
Suitable for
heating up, keeping warm defrosting
steaming, soaking, cooking
frying, deep-fat frying
1-3
4-5
6-8
9
heating large quantities
6
Users Guide - EKWE/EKWH - USA
If you touch the plus key, the cooking zone starts at setting 5, without an
automatic boost.
If you touch the minus key, the cooking zone starts at setting 9.
In this case the automatic boost function is automatically activated too.
Switching off the cooking zone:
press the plus sensor and the minus sensor simultaneously.
and
Automatic boost function
All cooking zones have an automatic boost function. The booster cooking
phase is activated at full power. The booster cooking time depends on the
subsequent cooking level which has been selected after the activation. The
cooking zone automatically changes to the selected subsequent cooking level
as soon as the set booster cooking time has elapsed.
If the pan-on detection function is activated and the pan is removed from
F
the cooking zone, the automatic boost function will be cut off. When a
pan is replaced on the cooking zone the automatic boost function
resumes operation again.
Selecting the required setting by means of the minus sensor will automatically
activate the automatic boost function.
During automatic operation an “A” will flash in the display in alternation with
the cooking level set.
If the automatic boost function is to be activated when the required setting is
selected by means of the plus sensor, the plus sensor must be touched again
once power level 9 has been reached.
2X
Users Guide - EKWE/EKWH - USA
7
Then set it at the required cooking level.
An “A” will flash in the display in alternation with the cooking level set.
Residual heat indicators
As long as the cooking zone is still hot an “H” will appear in the display when
the cooking zone has been switched off.
Dual-circuit cooking zones
Dual-circuit cooking zones are indicated by means of a flashing cooking zone
symbol under the plus/minus sensors.
Depending on the size of the pan on the cooking zone, the pan-on detection
will activate either the inner cooking zone circuit alone or both circuits. The
cooking zone symbol stops flashing when both circuits have been activated.
If the pan-on detection has been switched off, the smaller cooking zone
will always heat up.
Switch on the outer circuit for large pans.
– Touch the cooking zone symbol under the plus/minus sensors.
The cooking zone symbol will stop flashing on activation.
Touching the cooking zone symbol again will deactivate the dual-circuit zone.
8
Users Guide - EKWE/EKWH - USA
The pan-on detection
All of the cooking zones have a pan-on detection and the dual-circuit zone
also has a pan size detection.
The pan-on detection will recognize pans made of metal.
In order to be able to use glass or ceramic cookware the pan-on
detection must be deactivated.
F
When a pan suitable for the pan-on detection is placed onto a cooking zone
which is switched off, the display will indicate a “U”.
If no pan or a pan unsuitable for the pan-on detection function has been
placed on the activated cooking zone, an underlined “U” appears in the
display.
Then the cooking zone switches off automatically after 1 minute.
Switching off the pan-on detection
The pan-on detection must be switched off when glass cookware or any other
cookware unsuitable for the pan-on detection is being used.
– Before setting the power level of the cooking zone, touch the plus and
minus sensors simultaneously.
The display will show a dot. This dot remains visible next to the power level
set.
and
If the dot blinks, it is an indication that the pan-on detection has developed a
defect. The cooking zone can still be operated with the pan-on detection
switched off. Select the circuit manually for dual-circuit cooking zones.
The automatic pan size detection for dual-circuit cooking zones
Dual-circuit cooking zones have a sensor which recognises the size of the pan
being used.
Only the inner circuit will be switched on if a small pan is placed on the
cooking zone. If the cooking zone is fully covered by a pan, both circuits will
be switched on.
Please ensure that the outer circuit is always fully covered, even in the case
of pans with a rounded base.
Moving the pan around during the cooking procedure may result in the outer
cooking circuit being switched off if it is not fully covered.
The outer cooking zone circuit can also be switched on or off manually if the
pan-on detection or the pan size detection is activated.
Users Guide - EKWE/EKWH - USA
9
The emergency switch
All of the cooking zones can be switched off quickly with the ON/OFF sensor.
Minute minder and switch-off function
The minute minder operates as a switch-off and as a reminder for a maximum
of 99 minutes. The time is set in minutes.
The minute minder also operates if the control honeycomb has been switched
off.
Adjusting the minute minder
– Touch the plus sensor lightly to switch on the minute minder.
The display will show “0”.
– Set the required time by touching the plus sensor again, if necessary for
longer. The time set can be reduced again by touching the minus sensor.
When the time set has elapsed, “0” will flash in the display and an acoustic
signal will sound. If you wish to stop the acoustic signal, press one of the
clock sensors.
Should you wish to switch the minute minder off before the time has elapsed,
touch the plus and minus sensors of the clock simultaneously.
Setting the switch-off function for a cooking zone
The switch-off function can be used to switch a cooking zone off after a
required period of time. The switch-off is a function of the minute minder and
can only be activated if a cooking zone has also been activated.
– Set a power level for the cooking zone selected.
– Set the minute minder to the time required.
– Now touch the clock sensor and the plus sensor of the selected cooking
zone simultaneously.
The bordering around the cooking zone and an LED display in the clock sensor
will flash simultaneously.
In order to deactivate the switch-off function, touch the plus and minus sensor
of the minute minder or switch off the cooking zone.
10
Users Guide - EKWE/EKWH - USA
Childproof lock (sensor lock)
The childproof lock can be used to protect the appliance against unauthorized
use. The cooktop must be switched on.
Activating the childproof lock:
– Touch the key sensor for approx. 2 seconds.
The childproof lock may also be activated while the appliance is in operation.
In this case, however, the settings of the cooking zone can only be turned
down or switched off.
An activated childproof lock will be indicated by means of flashing plus and
minus sensors of one of the operating fields not required for your honeycomb
layout and the flashing control lamp of the locking sensor.
Please note:
The touch control not in use which is used to indicate the childproof lock
depends on the layout of your honeycomb cooking zones and varies from
model to model.
Attention:
Switching the cooktop off does not cancel the childproof lock!
Cancelling the childproof lock:
– Touch the flashing plus and minus sensors simultaneously until an
acoustic signal sounds.
simultaneously,
– Then touch the key sensor within a period of 2 seconds.
after max. 2 sec.
Note:
The childproof lock will no longer be activated after a power failure.
Time limit function (holiday function)
The appliance has an automatic time limit function. It prevents the appliance
from being in operation for a longer period of time.
The timer of the time limit function depends on the setting of the cooking
level:
The higher the setting of the cooking level the faster it switches off.
Cooking level
Appliance switches off after
9
8
7
6
2 hours
5
4
3 hours
4 hours
5 hours
3
2
1
10 hours
Users Guide - EKWE/EKWH - USA
11
Other functions
• If two or more sensor keys are pressed at the same time – e.g. when a
pan is mistakenly put onto a sensor key – no function is activated. An
audible signal sounds after 10 seconds. The appliance switches off
automatically after 20 seconds.
Exceptions:
– Cancelling the childproof lock.
– Switching off the cooking zones.
– Switching off / activating the minute minder of a cooking zone.
• If you continue to press a sensor key after having set the highest cooking
setting, an audible signal sounds after 10 seconds. After 20 seconds the
appliance switches off automatically.
• The appliance does not automatically switch on again after a power failure.
A childproof lock which was activated prior to a power failure it will be de-
activated.
• The cooktop is switched off if the electronics become overheated. All 4
LED displays flash and a cyclical signal sounds.
Selecting pots and pans
CAUTION! Only certain types of glass, glass/ceramic, ceramic, earthenware,
or other glazed cookware are suitable for range-top service without breaking
due to the sudden change in temperature. Follow the manufacturer's
instructions!
Only pots and pans made of metal can be used with the pan recognition
function. To use other kinds of utensils, please deactivate the pan
recognition function.
F
You can save time and power by using ideal pots and pans.
• Use pots and pans with flat, smooth bottoms.
Uneven bottom surfaces can increase energy usage and the amount of
time needed to start the cooking process.
• Pans with rough bottom surfaces will scratch the glass-ceramic cooking
area when they are moved around.
• Use a pan with a diameter at least as large as the cooking area.
Using undersized cookware will expose a portion of the heating element
to direct contact and may result in ignition of clothing.
• Whenever possible, always place a lid on the pan.
It will help you save a lot of energy. Liquids and foods will only boil over
if the temperature is set too high. The cooking zones enable you to set
the required temperature precisely. With a little practice, you’ll learn how
to choose the perfect cooking settings so nothing will boil over--even when
a lid is on.
12
Users Guide - EKWE/EKWH - USA
Cleaning and care
Sugar and food containing sugar (i.e. marmalade) and melted plastic must
immediately be removed from the hot cooking surface with the cleaning
scraper. If not, the cooking surface can be ruined while it’s cooling down.
Steam and/or pressure cleaning machines can’t be used to clean the
appliance! This can damage the unit, and result in the risk of personal injury.
Risk of burning! Make sure the appliance has cooled down before cleaning.
If a wet sponge or cloth is used to wipe spills on a hot surface, you could be
burned by the resulting steam. Be aware that some cleaners can produce
noxious fumes if applied to a hot surface.
Please note the instructions regarding cleansers.
Clean the cooking surface after every use. Food residue that hasn’t been
removed will burn into the surface the next time it’s turned on and then
these incrustations may be permanent.
F
Cleanser residues can cause discoloration the next time you turn on the
cook top. Cloths and sponges that have been used to clean other
surfaces can cause discoloring, too.
F
VSR O-FIX-C is the perfect cleanser for glass ceramic. You can get it
from KÜPPERSBUSCH Customer Service.
F
Do not use any
– aggressive or bleaching cleaning agents that contain active oxygen,
chlorine or corrosive components.
– abrasive or aggressive cleaning or scouring agents like steel wool, soap-
filled steel wool, metal or plastic sponges or similar agents with an
abrasive surface.
Please note the information for the cleaning scraper
CAUTION! Risk of cutting! The blade of the cleaning scraper is very sharp!
Always keep the cleaning scraper flat on the surface and push the caking
away.
Do not scratch the surface with the edge of the scraper and don’t damage
the sealing with the edge.
Cleaning the cooking surface
– Use the cleaning scraper to remove all food residue and fat splashes from
the hot cooking surface.
– When the cooking surface has cooled, clean it with water and a small
amount of detergent, with a cleanser for glass ceramic surfaces or with
VSR O-FIX-C. A soft brush or a soft sponge can also be used.
– Wipe off the surface with clear water.
– Dry it thoroughly.
Remove caking
Heavy food residue should be soaked first. Use a wet cloth for best results.
It will be easier to remove the food residue.
Care of the cooking surface
Clean the glass ceramic surfaces with a cleanser to protect it from discoloring,
and reduce the danger of damage from sugar. It can also remove stains and
discoloration.
Users Guide - EKWE/EKWH - USA
13
What to do if trouble occurs...
Never unscrew the appliance! Only a qualified technician should
perform repairs!!
However, there are some problems that you can handle yourself. First, check
and see if there have been any operating errors. Remember – repairs during
the warranty period are not free of charge if they are caused by operating
errors or non-observance of the following instructions:
Problem
Possible cause
Solution
Circling symbol lines in LED displays.
No fault;
normal display after power cuts.
If there were no objects on the sensors
confirm by means of the “off”sensor.
Horizontal lines in the displays running from top Faulty electronic component.
to bottom.
Disconnect the fuse,
call Customer service.
Not possible to switch off the cooktop.
Faulty electronic component.
Disconnect the fuse,
call Customer service.
LED display for cooking settings and heat display LED display defective.
does not come on or only partially.
Call Customer service.
Risk of burning, as the temperature
warning is not guaranteed.
Cooking zone does not heat up.
Household fuse defective.
Child-proof lock not unlocked.
Cooking zone defective.
Check and replace fuse, if necessary.
Unlock child-proof lock.
Call Customer service.
Inner circuit of a dual-circuit cooking Under no circumstances continue to
zone defective.
use the outer circuit which is still
working!
Immediately call Customer service.
The plug is not inserted in the power Put the plug in again.
component or in the control
honeycomb.
Individual sensors or all of the sensors no longer Power failure or fault in the
react to touch. electronics system.
Brief disconnection of the cooktop
from the power source (by means of
the fuse).
Pan-on detection reacts to the wrong cooking No start or faulty start.
zone / the wrong cooking zone heats up / dual-
circuit zones incorrectly allocated
Start-up once again. See “Installation
instructions”.
If this dot blinks, it is an indication that the pan-on detection has developed
a defect. The cooking zone can still be operated with the pan-on detection
switched off.
Should you need to contact Customer service or order spare parts, always
quote the information printed on the model identification plate. It is located
underneath the control honeycomb. You will also find it stuck onto the front
page of the operating instructions enclosed.
14
Users Guide - EKWE/EKWH - USA
After Sales Service
In the event of a problem that you can’t easily fix yourself, or for spare part
service, please contact the Küppersbusch Customer Care line at
.ꢀꢁꢂꢃꢃꢁꢄꢅꢆꢁꢃꢂꢄꢄ
Always have the information from the identification panel handy when
calling Customer Service.
F
The panel is located on the underside of the cook top and on the cover page
of this manual.
Production number
Model
Users Guide - EKWE/EKWH - USA
15
KÜPPERSBUSCH USA
4920 West Cypress Street,
Tampa, Florida 33607
Telephone: 813-288-8890 Fax: 813-288-8604
Customer Care line: 1 - 800 - 459 - 0844
KÜPPERSBUSCH IS A BRAND OF TEKA USA, INC.
|