WO15Z-1
Receptacle, Series 300
Radio Frequency Controlled, 120 VAC, 15A, Duplex
GROUND
GREEN
TOTAL LOADS MUST NOT EXCEED
15 AMPS @ 120 VAC
(INCLUDES ALL LOADS PLUGGED INTO
THE RECEPTACLE)
ALWAYS POWERED
OUTLET
WHITE
CONTROLLED
OUTLET
NEUTRAL
BLACK
LINE 120 VAC
TOTAL LOADS MUST NOT EXCEED 15 AMPS @ 120 VAC (INCLUDES ALL LOADS PLUGGED
INTO THE RECEPTACLE
NOTE: This module must be “included in the Network” only where it will be permanently installed. The proper operation of this node in the
mesh network is dependent on it knowing its location with respect to other nodes.You cannot “test bench” configure this module, then install.
STEP 3. You should see an indication on your Controller that the
“DEVICE WAS INCLUDED” in the network.
WO15Z-1 DUPLEX RECEPTACLE
Linear’s family of Z-Wave certified wireless lighting controls (switches,
dimmers, outlets and plug-in modules) brings a new level of intelligent
wireless capability to commercial and residential environments.
NOTE: If you have trouble adding the WO15Z-1 to a group it may be
that the Home ID and Node ID were not cleared from it after testing.
You must first “RESET UNIT” with your controller to remove it from the
network.
The Z-Wave wireless protocol is an international wireless standard
for remote home automation, security and other applications.
Embedded in each device, the Z-Wave smart chip enables two-way RF
communication among hundreds of Z-Wave enabled devices, allowing
products and services from multiple manufacturers to work seamlessly.
Although adding it to a group includes it in the network, removing it from
a group does not remove it from the network. If removed from a group, it
functions as a repeater only.“RESET UNIT” removes it from the network
Linear Z-Wave products are easy to install, and allow dealers to create
an integrated wireless network with nearly limitless expansion and
interoperability with security and health monitoring systems, energy
management, home entertainment, appliances, and more.
Receptacle Configuration
TheWO15Z-1 Receptacle controls the ON and OFF of a load connected
to the controlled outlet (See Wiring Diagram for identification).The
other outlet remains powered all the time. A button on the face of the
receptacle is used to add the module to the wireless network and be
controlled from the wireless controller.With the Wireless Controller, the
WO15Z-1 Receptacle can be turned ON and OFF remotely, and can
be included in groups that operate at the same time (a group can be a
single module), and in scenes that set a lighting mood.
As part of a Z-Wave network, the WO15Z-1 will also act as a wireless
repeater to insure that commands intended for another device in the
network are received. This is useful when the device would otherwise
be out of the radio range of the wireless controller.
DANGER! SHOCK HAZARD. Read and understand these
instructions before installing. This device is intended for installation in
accordance with the National Electric code and local regulations in the
United States, or the Canadian Electrical Code and local regulations
in Canada. It is recommended that a qualified electrician perform this
installation. Make sure the total load controlled does not exceed 1800
watts. For indoor use only. Retain instructions for future use.
Local ON and OFF
When the button on the face of the WO15Z-1 is pressed, the power to
the controlled outlet will turn on. When the button is pressed again, the
controlled outlet will turn off.
Child Protection
The WO15Z-1 controlled outlet can be set in a child protect mode by the
Wireless Controller. When this mode is active, a user will have to press
the button on the face 3 times rapidly to activate the attached load. The
module operates normally when controlled by the Wireless Controller.
INSTALLATION
Wire this receptacle in place of a current receptacle according to the
diagram above. Use copper wire only, or equivalent.
Other Functions
INCLUDING WO15Z-1 TO THE NETWORK
The button on the face of theWO15Z-1 Receptacle can be used to carry
out inclusion (add to a group), association (operate simultaneously with
other nodes), exclusion (remove from group) or reset (remove from
network). The WO15Z-1 has a blue indicator LED. This LED will turn
on when the controlled outlet is on and will turn off when the controlled
outlet is off. However, its behavior can be configured as a “night light”
(LED ON when the controlled outlet is off). See Configuration section
below on how to do it.
STEP 1. Prepare the Controller to include a unit to the network, by
adding it to a group (method of adding a node to the network). Refer to
controller instructions.
STEP 2. The WO15Z-1 must be in its permanently installed
location. Tap the button on the face of the WO15Z-1 once when your
controller indicates (to include in the network).
1
|