Patton electronic Switch FAQs User Manual

FAQs   
   
 
  
 
  
Applications  
What is the primary application for the Model 1058, 12.5 Mbps VDSL Ethernet Extender?  
LAN Extension & Service Integration  
Used in pairs, the Model 1058 establishes a high-speed, line sharing, symmetrical 12.5 Mbps voice and data  
link. The Model 1058 inter-connects two geographically separated LANs over a voice-grade twisted pair  
wire. Operation is simple: packets destined for the remote LAN are sent transparently, at full line rate, to the  
peered LAN. The Model 1058DV's built-in POTS/ISDN splitter allows users to simultaneously talk on the  
phone while surfing the WWW, downloading files, or receiving emails.  
Other Applications include:  
MTU/MDU Internet Services  
Network Backbones  
Remote Workstations and Equipment  
ISP Last Mile Extension  
1
 
FAQs   
   
 
  
 
  
Does the Model 1058 operate in pairs?  
Yes, the Model 1058 must operate in pairs. For each link, a Central Office (1058DV/CO/E) and Customer  
Premise (1058DV/CP/E) unit is required. For concentrated applications, the 1058DVRC/CP and  
1058DV/CP/E standalone can be used to operate with the VDSL Concentrator (Model 3324).  
Which end of the link should the “CO” Central Office unit and “CP” Customer Premise unit  
be located?  
The Model 1058DV/CO and 1058DV/CP should be located according to their descriptions. The 1058DV/CO  
unit should to be placed at the Central Location and the 1058DV/CP should be placed at the Customer  
Premise (Remote) due to special filtering requirements for each application.  
Does the Patton Model 1058 support VLAN?  
The Model 1058 will support VLAN (802.1Q) by passing the larger sized packets transparently. The Model  
1058 does not have configuration commands to add a VLAN tag to a packet.  
Does the Patton Model 1058 pass higher layer protocol such as TCP/IP packets?  
Yes, the Model 1058 does pass higher layer protocols such as TCP/IP. The Model 1058 does not read the  
TCP/IP packets, but will pass the packets on transparently.  
Is the Model 1058 capable of bridging?  
Yes, the Model 1058 will automatically learn, age, and filter 32 source addresses. Destination addresses of  
incoming frames are compared with the Source Address in the address table and discarded if an entry  
exists; otherwise, they are forwarded over the VDSL link.  
Can voice and data be used simultaneously?  
Yes, voice and data can be used simultaneously.  
Will the POTS/ISDN port on the Model 1058DV operate without power?  
The built-in POTS/ISDN Splitter is a passive element and does not require power to operate. The  
POTS/ISDN port is able to provide a “life-line” telephone link provided the physical connection between the  
CO and CP VDSL modems is still intact.  
3
 
FAQs   
   
 
  
 
  
Ethernet (10 or 100Base-T) Interface  
What devices typically connect to the Ethernet 10/100Base-TX port?  
Devices that typically connect to the Ethernet port are Ethernet Hubs/Switches, Remote PC’s, and any other  
network enabled device.  
How is the Ethernet port configured to accept 10 or 100Base-TX?  
The Ethernet port automatically senses 10 or 100Base-TX Ethernet connections.  
Does the Ethernet port require configuration for full or half-duplex connections?  
The Model 1058 will automatically sense full or half-duplex Ethernet connections. To fully utilize the  
100Base-TX Full-Duplex feature, your network enabled devices must support 802.3x flow control (pause  
packets). A switch setting is provided on the Model 1058 to transparently lock out the 100Base-TX full  
duplex communication if your network enabled devices do not support 802.3x flow control (pause packets).  
This feature will only allow Ethernet connections in 10Base-T full/half duplex or 100Base-TX half duplex and  
transparently avoid the 802.3x issue without degrading link performance.  
Do I use straight-through or crossover cables?  
The 1058 is equipped with an MDI-X switch that enables automatic connections to a hub (DCE) or PC (DTE)  
interface, thereby eliminating confusion over whether a straight-through or crossover cable is needed. The  
Ethernet port will automatically sense the required connection type.  
Power Supply  
What are the power supply options for the Model 1058’s?  
The Model 1058’s come standard with an external 120VAC or UI (100-240VAC) power supply. –48, -24, or  
-12VDC power supplies are optional and ordered separately.  
4
 

Peavey Musical Instrument Amplifier Renown User Manual
Philips Coffeemaker HD7854 User Manual
Philips Electric Shaver 5841XL User Manual
Philips Flat Panel Television 14PT3685 05 User Manual
Philips Hair Care Product HP8361 00 User Manual
Philips Stereo Amplifier BGY1916 User Manual
Philips Universal Remote SBC RU 510 00U User Manual
Planet Technology Printer PS 1010MG User Manual
Polk Audio Portable Speaker SC80 User Manual
Powerware Power Supply 15 KVA User Manual