IMPORTANT FOR FUTURE REFERENCE
Please complete this information and retain this manual
for the life of the equipment:
Model #: _____________________________
Serial #: _____________________________
Date Purchased: ______________________
Installation & Operation Manual
PE14D: Floor Model Electric Pasta Cooker
RS14D: Floor Model Rinse Station
Built after 11/2003
L20-293, rev. 0 (1/06)
PE14D: Floor Model Electric Pasta Cooker
TABLE OF CONTENTS
1. INSTALLATION.........................................................................................1
1.1. CHECKING YOUR NEW APPLIANCE...................................................................................1
1.2. INSTALLATION CLEARANCES............................................................................................2
1.3. LEG/CASTER INSTALLATION AND LEVELING....................................................................2
1.4. PLUMBING CONNECTIONS.................................................................................................3
1.4.1.
1.4.2.
WATER INLET CONNECTIONS......................................................................................3
DRAIN CONNECTIONS..................................................................................................3
1.5. ELECTRICAL CONNECTIONS..............................................................................................3
1.6. VENTILATION AND FIRE SAFETY SYSTEMS ......................................................................4
1.7. INSPECTION........................................................................................................................5
1.8. INITIAL CLEANING ..............................................................................................................5
2. OPERATION..............................................................................................6
2.1. FILLING THE APPLIANCE....................................................................................................8
2.1.1.
2.1.2.
FILLING THE COOKER TANK ........................................................................................8
FILLING THE RINSE TANK ............................................................................................8
2.2. APPLIANCE START UP .......................................................................................................9
2.3. COOKING ............................................................................................................................9
2.3.1.
2.3.2.
2.3.3.
2.3.4.
2.3.5.
2.3.6.
SIMMER MODE .............................................................................................................9
BOIL MODE ................................................................................................................. 10
TIMER OPERATION..................................................................................................... 10
BASKET LIFT OPERATION.......................................................................................... 10
ADDITIONAL CONTROLLER FUNCTIONS ................................................................... 10
COOKING TIPS ........................................................................................................... 10
2.4. APPLIANCE SHUTDOWN................................................................................................... 10
3. PREVENTATIVE MAINTENANCE........................................................ 11
3.1. DAILY PREVENTATIVE MAINTENANCE ............................................................................ 11
3.1.1.
3.1.2.
APPLIANCE INSPECTION............................................................................................ 11
CLEANING THE COOK TANK (RINSE TANK IF EQUIPPED)......................................... 11
iii
TABLE OF CONTENTS
3.1.3.
CLEANING THE CABINET............................................................................................ 11
3.2. MONTHLY PREVENTATIVE MAINTENANCE...................................................................... 12
3.2.1.
DELIMING.................................................................................................................... 12
3.3. ANNUAL/PERIODIC PREVENTATIVE MAINTENANCE AND INSPECTION.......................... 12
3.3.1.
3.3.2.
3.3.3.
3.3.4.
3.3.5.
3.3.6.
HEATING ELEMENT.................................................................................................... 12
TEMPERATURE PROBE & HIGH LIMIT PROBE ........................................................... 12
CONTROLLER............................................................................................................. 12
CONTROL BOX & ELECTRICAL COMPONENTS.......................................................... 13
TANK........................................................................................................................... 13
DRAIN SYSTEM........................................................................................................... 13
4. TROUBLESHOOTING ........................................................................... 14
4.1. POWER FAILURE .............................................................................................................. 14
4.2. HIGH TEMPERATURE LIMIT.............................................................................................. 14
4.3. DRAIN VALVE INTERLOCK ............................................................................................... 14
4.4. TROUBLESHOOTING CHART............................................................................................ 15
4.5. CONTROLLER WARNING DISPLAYS ................................................................................ 15
iv
L20-293, rev. 0 (1/06)
PE14D: Floor Model Electric Pasta Cooker
INSTALLATION
1. INSTALLATION
1.1. CHECKING YOUR NEW APPLIANCE
Your new Pitco appliance has been carefully packed into one crate. Every effort has been made to
ensure that it is delivered to you in perfect condition. As you unpack your new appliance, inspect each
of the pieces for damage. If something is damaged, DO NOT sign the bill of lading. Contact the
shipper immediately; the shipper is only responsible for 15 days after delivery. Check the packing list
enclosed with your appliance to ensure that you have received all the parts to the appliance. If you
are missing any parts, contact the dealer from whom the appliance was purchased. As you unpack
the appliance and its accessories be careful to keep the weight of the appliance evenly distributed.
Refer to the table below to identify which accessories should be included with your appliance.
Locate your Pitco model number and serial number on the inner door of the appliance and the find
the date purchased. Write this information on the front cover of this manual for future reference.
If you have completed the above steps that are applicable to the appliance you purchased, the
appliance is now ready to be installed. Although it may be possible for you to install and set up your
new appliance, it is STRONGLY recommended that you have this done by qualified professionals. A
qualified professional will ensure that the installation is safe and meets local building and fire codes.
Accessories
#
1
2
3
4
5
6
7
8
9
Description
Basket Hanger
PE14D
Standard
Standard
RS14D
Standard
N/A
WARNING
DO NOT sit or stand on this
appliance. The appliance’s front
panel, tank, splash back, tank
cover, workshelf, drain board is
not a step. Serious injury could
result from slipping, falling or
contact with hot liquids.
Element Rack
Drain Cleanout Rod
Small Bulk Pasta Basket
Large Bulk Pasta Basket
Small Round Pasta Basket
Large Round Pasta Basket
Oblong Pasta Basket
Portion Cups with Rack
Standard
Optional
Optional
Optional
Optional
Optional
Optional
Optional
Optional
Optional
Optional
Optional
Optional
1
INSTALLATION
1.2. INSTALLATION CLEARANCES
The clearances shown below are for combustible and non-combustible installations and will allow for
safe and proper operation of your appliance.
Combustible Construction
Inches (centimeters)
6.0" (15.24cm)
Non Combustible Construction
Inches (centimeters)
0.0" (0.0cm)
Back
Sides
Counter
6.0" (15.24cm)
6.0" (15.24cm)
0.0" (0.0cm)
6.0" (15.24cm)
In addition to the above clearances there must also be at least 16 inches (40.64cm) of aisle space in
front of the unit.
WARNING
WARNING
DO NOT obstruct the flow of ventilation, or air openings
around the appliance. Adequate clearance around the
appliance is necessary for servicing and proper
component ventilation. Ensure that you meet the
minimum clearance requirements specified in this manual.
DO NOT install this appliance next
to a deep fat fryer. A splash over of
water into the hot oil may cause a
flash fire.
CAUTION
To prevent equipment damage and/or personal injury, do not tilt the appliance
onto any two of its casters or legs, or pull the appliance by the splash back.
1.3. LEG/CASTER INSTALLATION AND LEVELING
When you receive your appliance it is completely assembled with the possible exception of the legs
(or casters). This appliance must be installed with legs or casters; it cannot be curb mounted. Curb
mounting will seriously inhibit this appliance’s ability to effect proper component ventilation. The
legs/casters must be installed before connecting the appliance to the power supply. The legs provide
the necessary height to meet sanitation requirements and assure adequate air supply for electrical
component ventilation. Use the following procedure.
WARNING
This appliance must be installed with the legs or casters provided by the manufacturer.
Required tools: 7/16 “ wrench and socket and a large pair of water pump pliers.
1. Lay the appliance on its back, being careful not to damage the splash back by pulling on it.
Protect the outside of the appliance with cardboard or a drop cloth when laying it down.
2. Attach each leg/caster with the hex head screws and nuts supplied. Each leg/caster requires
four ¼-20 x 5/8” hex head screws and nuts. Insure that all screws are tight.
3. Mount the screws from the inside of the appliance with the nut on the outside (bottom) of the
appliance. The nuts have lock washers attached to
them, therefore it is not necessary to use separate lock
washers.
WARNING
DO NOT install legs or casters, or perform
leveling procedure when appliance is in operation
or full of hot liquids. Serious injury could result.
4. When all four legs/casters are securely mounted, stand
the unit up, being careful not to put too much weight on any one leg. Adjust the height and level
the appliance by adjusting the leveling devices (B) with water pump pliers. On casters, loosen 2
screws (A) before leveling, make your height adjustments, then retighten.
2
L20-293, rev. 0 (1/06)
PE14D: Floor Model Electric Pasta Cooker
1.4. PLUMBING CONNECTIONS
INSTALLATION
The plumbing installation should be done by a licensed plumber and must comply with local and
national codes.
1.4.1. WATER INLET CONNECTIONS
If a faucet or water fill option is equipped on your appliance connections to a potable water supply
will be required. If a single water connection is required it is recommended that the appliance is
connected to hot water supply. This will greatly decrease the time it takes for the appliance to
reach operating temperature. Prior to installation, a water treatment specialist should inspect the
water supply. Water hardness should contain no more then 2.0 grains/gallon. The pH level
should be between 6.5 and 8.0. These conditions can be obtained with the use of a properly
maintained water softener. The incoming water pressure should be between 20 psi (1.38 bars) to
60 psi (4.14 bars). For higher water pressures, a high-pressure regulator must be installed to
inlet plumbing to avoid damage caused by water hammer. The maximum allowable incoming
water temperature is 180°F (82°C). Have your water tested and record the measured values
below.
Water Quality Checklist
WARNING
When water is at a high
Measured
Range
OK
temperature and high
pressure, excessive
splashing of hot water
may occur that could
result in injury.
Temperature
Hardness
pH
180°F (82°C) Max.
2.0 Grains/Gal. Max.
6.5 to 8.0
Pressure
20 psi to 60 psi
1.4.2. DRAIN CONNECTIONS
Each tank has a drain that can be inserted into a drainage system. Each tank also has an
overflow line. The overflow connection is after the drain valve to provide an unobstructed
overflow path. The drain and overflow line for each tank may be connected together to form a
common drain line.
1.5. ELECTRICAL CONNECTIONS
It is advised that this power supply be plugged into a wall receptacle that is controlled by the
ventilation control. This will prevent the appliance from being operated without the ventilator on. If
your appliance requires an electrical connection, the power requirements are listed below.
WARNING
Voltage/Phase
KW Amps
All copper wiring for this appliance must be made
in accordance with the wiring diagram(s) located
on the appliance.
200VAC, single phase
208VAC, single phase
220VAC, single phase
240VAC, single phase
200VAC, three phase
208VAC, three phase
220VAC, three phase
240VAC, three phase
346/200VAC, three phase 11.6
380/220VAC, three phase 11.4
400/230VAC, three phase 12.5
415/240VAC, three phase 12.5
11.6
12.5
11.4
12.5
11.6
12.5
11.4
12.5
58
60
52
52
33
35
30
30
19
17
18
17
CAUTION
Connecting the appliance to the wrong power
supply may damage the appliance and void the
warranty.
WARNING
A country approved all pole circuit breaker with a
minimum open contact gap of 3mm must be used
for proper installation. (CE countries)
WARNING
This appliance must be connected to a power supply having the same voltage and phase as
specified on the data plate located on the inside of the appliance door.
3
INSTALLATION
WARNING
DO NOT attempt to connect the appliance to an electrical supply other then that indicated
on the data plate. Electrical connection should be performed by qualified personnel.
WARNING
The electrical connection used by this appliance must comply with local codes. If there are
no local codes that apply, refer to the National Electrical Code (NEC), ANSI/NFPA 70 for
installation in the US. In Canada, refer to CSA Standard C22.2 and local codes. In all other
cases, refer to local and national codes and regulations.
WARNING
The appliance must be grounded in accordance with local code; if there is no local code,
comply with the NEC and ANSI/NFPA No. 70 latest edition (for US and Canadian
installations). In all other cases, refer to local and national codes and regulations. To
comply with European requirements, European models are equipped with an equalization-
bonding clamp. An equalization bonding lead must be connected to this clamp to provide
sufficient protection against potential difference. This clamp, located on the rear of the
appliance is marked with the following universal symbol.
WARNING
This equipment must be installed so that the plug is
accessible unless other means for disconnection
from the power supply (e.g. a circuit breaker) is
provided.
WARNING
If this appliance is permanently connected to fixed
wiring, it must be connected by means of copper
wires having a temperature rating of not less then
167°F (75°C).
To Access Electrical Connections
Phillips Screwdriver Required
1) 1” (2.54cm) Access Hole
2) Connection Points
1/2” (1.27cm) Allen Wrench Required
3) Ground Connection
Flat head screwdriver required
1.6. VENTILATION AND FIRE SAFETY SYSTEMS
Your new appliance must have proper ventilation to function safely and properly. It is very important
to install a fire safety system. Your ventilation system should be designed to allow for easy cleaning.
Frequent cleaning and proper maintenance of the ventilation system and the appliance will reduce the
chances of fire. Ventilation and fire safety systems must comply to local and national codes. Refer to
ANSI 83.11 for a list of reference documents that will provide guidance on ventilation and fire safety
systems.
4
L20-293, rev. 0 (1/06)
PE14D: Floor Model Electric Pasta Cooker
1.7. INSPECTION
INSTALLATION
Before you begin filling and operating the appliance, perform the following visual checks:
ü After the appliance is in its permanent location, check
the levelness. Any additional leveling that is
necessary can be performed as previously described.
ü Ensure that the probe, heating element and high
temperature limit is in place and secure. Check the
high limit bulb mounting screws to ensure that they
are tight.
ü Review the installation portion of this manual and
ensure that all steps have been followed and
executed properly.
1) Probe
CAUTION
2) High Temperature Limit
(may be either style)
3) Heating Element
Be careful not to disturb the probe and
high temperature limit during operation
and cleaning of this appliance.
1.8. INITIAL CLEANING
When your appliance is shipped, many of its parts are covered with a thin coat of oil for protection.
Before the appliance is ready for cooking it must be cleaned. This will remove the oil coating and any
foreign matter that may have accumulated during storage and shipment. Refer to the following
procedure to clean the appliance.
WARNING
Wear protective gloves and clothing when cleaning and draining the appliance and
when disposing of water. The water is extremely hot and can cause severe injuries.
CAUTION
DO NOT leave the appliance unattended during cleaning. Never let the water level
go below the heating element.
1. Read the “operation” section of this manual prior to filling or operating the appliance.
2. The following steps should be followed using a grease dissolving commercial cleaner.
WARNING
Use a commercial grade cleaner formulated to effectively clean and sanitize food
contact surfaces. Read the directions and precautionary statements before use.
Particular attention must be paid to the concentration of cleaner and the length of
time the cleaner remains on the food contact surfaces.
3. Following the manufacturer’s directions, clean the tank interior and all other food contact
surfaces.
4. When cleaning is complete, rinse the inside of the tank thoroughly with cool water. Continue to
rinse the tank until the cleaner has been completely and thoroughly rinsed from the tank.
5. Using a clean dry cloth, wipe out all of the water.
6. Repeat the previous steps to clean the rinse station if equipped.
5
OPERATION
2. OPERATION
An operator’s manual for your appliance’s specific control type should be included with this manual.
Refer to that manual prior to operating this appliance.
2.1. OPERATIONAL FEATURES
The diagram below outlines some of the key operational components of your appliance. Refer to the
following sections of this manual to learn more about these features.
6
L20-293, rev. 0 (1/06)
PE14D: Floor Model Electric Pasta Cooker
OPERATION
1. Cook Tank
2. Controller (Not on all Models)
Controls the water temperature inside the cook tank. Optional timers are located on the controller
(if equipped). Includes button to switch between boil mode and simmer mode (not on all models).
If the controller has an ON/OFF button, it will be used to turn ON the controller as well as other
features on the appliance.
3. Door (Shown Open)
Provides access to the drain valve handle, and high temperature reset button.
4. Drain Valve Handle (Shown in the closed position)
Opens the drain valve so water can be drained from the cook tank. If the drain valve interlock
feature is equipped, the appliance will stop heating if the drain valve is opened.
5. Drain Outlet
Water exits the cook tank through the drain outlet when draining or overflowing.
6. Overflow Line
When the cook tank water level reaches the overflow, water will flow unobstructed through the
overflow line and eventually exit the appliance through the drain outlet.
7. High Temperature Reset Button
This button may need to be pressed in the event that the high temperature limit has tripped.
8. Basket Hanger
For hanging and/or draining baskets when they are outside of the cook tank.
9. ON/OFF Switch (Not on all Models)
Turns the appliance ON and OFF. Some controllers require that they are turned ON by another
button after the ON/OFF switch is in the ON position.
10. Boil/Simmer Switch
Switches the appliance between boil and simmer mode. May be part of controller on some
models.
11. Manual Water Fill Knob (Not on all Models)
Fills the cook tank with water. May be adjusted for the proper water flow into the cook tank.
12. Hot/Cold Faucet (Not on all Models)
Fills the cook tank or rinse tank (if equipped) with water.
13. Element Box
DANGER: High voltage present. Do NOT open.
This box covers the high voltage wires going to the heating element from the entrance box.
14. Entrance Box
DANGER: High voltage present. Do NOT open.
The main power for the appliance is connected inside this box.
Electrical components that control the heating elements are located inside this box.
7
OPERATION
2.2. FILLING THE APPLIANCE
2.2.1. FILLING THE COOKER TANK
It is recommended that the cooker tank is filled with hot water.
This will greatly decrease the time it takes for the appliance to
reach operating temperature. Refer to the following procedure to
fill the cook tank prior to operation.
CAUTION
DRAIN VALVE CLOSED
This appliance is not designed for cooking
with oil. Fill with potable water only.
Tank Capacity
1. Ensure that the drain valve is closed.
Model
PE14D
Capacity
12 Gal.
(45.5 Liters)
2. Fill the tank with water until the water reaches the water
level line(s).
WARNING
Water must completely cover the heating elements at all times while appliance is on.
2.2.2. FILLING THE RINSE TANK
Once pasta is cooked to the desired doneness it will continue to cook after being removed from
the cook tank until its internal temperature is lowered. Submerging the pasta in cold water or
rinsing it with cold water will lower the pasta’s internal temperature and stop the cooking process.
Rinsing or submerging will also prevent sticking and remove dissolved starch. If the appliance is
equipped with a rinse tank, it may be filled with cold (or ice) water for submerging the pasta after
it leaves the cook tank. Refer to the following procedure to fill the cook tank prior to operation.
1. Ensure that the drain valve is closed.
2. Fill the tank with cold water (and ice if desired) until the water reaches the water level line(s).
If the rinse tank does not have level lines, fill the tank so that the water is 4 inches
(10.16cm) below the overflow. The tank can be filled up beyond the desired level but water
may be lost through the overflow once pasta is placed into the tank.
8
L20-293, rev. 0 (1/06)
PE14D: Floor Model Electric Pasta Cooker
OPERATION
2.3. APPLIANCE START UP
Refer to the following procedure to start the appliance prior to operation.
1. Ensure that the drain valve is closed.
2. Fill the cook tank with water. (See section 2.1 “Filling the Appliance”)
3. If the appliance is equipped with a I/0 (ON/OFF) switch, turn it to the I (ON) position.
WARNING
NEVER operate the appliance with an empty cook tank. It may void the warranty.
Adding water after the elements have been heated may cause injuries from hot
splattering liquids and steam.
*
4. If the appliance is equipped with a controller it may need to be turned on. Press the
to turn the controller on.
button
*The specified button may appear slightly different then shown. Refer to the operator’s
manual for your appliance’s specific control type to determine the exact appearance of each
button and display.
5. The appliance is now on and heating the water in the cook tank.
WARNING
Water must completely cover the heating elements at all times while appliance is on.
2.4. COOKING
It is important to keep the cook tank full of water to minimize the chance of boiling the appliance dry
and to keep the water at a level that will provide optimum cooking performance. To keep the water at
its normal operating temperature, it is best to add water in small amounts. If the appliance is
equipped with manual water fill, it is recommended that the fill knobs are set so that water enters the
tank slowly during cooking.
WARNING
Dry fired elements are extremely hot, will shorten its service life and may void your warranty.
2.4.1. SIMMER MODE
Simmer mode maintains the water temperature to just below boiling. This mode can be used to
reheat pasta or as a “stand by” mode.
To enter simmer mode:
Models with electric thermostat: Press the boil/simmer switch to the simmer position.
*
*
All other Models: Press the
button until
is displayed.
If you are not ready to cook, enter simmer mode. This will conserve energy and keep water in the
tank longer then when in boil mode.
9
OPERATION
2.4.2. BOIL MODE
Boil mode consistently heats the water so that the water will boil. Once the water starts to boil the
appliance is ready to cook pasta.
To enter boil mode:
Models with electric thermostat: Press the boil/simmer switch to the boil position.
*
*
All other Models: Press the
button until
is displayed.
2.4.3. TIMER OPERATION
Not all control types include timers. Timers provide accurate cook times for multiple product
quantities and types. Refer to the operator’s manual for your appliance’s specific control type to
determine how to set the cook timers if equipped.
To start a timer: Press the appropriate timer button.
Typical Timer Buttons*
2.4.4. BASKET LIFT OPERATION
If the appliance is equipped with basket lifts, place the pasta basket onto the basket lift prior to
starting the timer(s). The basket(s) will be lowered into the cook tank when the timer cycle starts.
At the end of the preset cooking time, the basket lift will raise the basket out of the cook tank.
2.4.5. ADDITIONAL CONTROLLER FUNCTIONS
Some controllers have additional functions not described in this manual. If your appliance’s
controller has additional functions, refer to the controller’s operation manual to access these
functions.
*The specified buttons and/or displays may appear slightly different then shown. Refer to
the operator’s manual for your appliance’s specific control type to determine the exact
appearance of each button and display.
2.4.6. COOKING TIPS
ü
ü
ü
Rinse pasta after cooking only if it is for cold dishes or if the pasta will NOT be served
immediately.
Cooked Pasta Volumes
For best results when cooking dry pasta, use at least 1
gallon of water for every 1 lb. of dry pasta.
1lb. Dry =
Cooked
10 cups
8 cups
7 cups
9 cups
Pasta Type
Spaghetti
Angel Hair
Fettuccine
Ziti
Sticky cooked pasta can be avoided by increasing the
quantity of water per pound or use of the manual fill
option while cooking (if equipped). The manual fill
should be set to a trickle while cooking to allow the
water continue boiling.
Shells
8 cups
Bow Ties
This table is for reference only.
Please refer to the pasta
manufacturer’s specifications to
determine exact cooked quantity.
10 cups
ü
ü
When storing pasta, keep the sauce separate because
the pasta will continue to absorb liquids after cooking.
Cooking oil can be added to cooked pasta prior to
storage to prevent sticking. 1-2 tsp. of oil per pound
(cooked) is typical.
2.5. APPLIANCE SHUTDOWN
Refer to the following procedure to shutdown the appliance.
1. If the appliance is equipped with a controller it should be turned OFF. Refer to the operator’s
manual for your appliance’s specific control type to determine how to do this.
2. If the appliance is equipped with a I/0 (ON/OFF) switch, turn it to the 0 (OFF) position.
10
L20-293, rev. 0 (1/06)
PE14D: Floor Model Electric Pasta Cooker
PREVENTATIVE MAINTENANCE
3. PREVENTATIVE MAINTENANCE
3.1. DAILY PREVENTATIVE MAINTENANCE
Performing the preventative maintenance steps below on a daily basis will keep your equipment safe
and at peak performance. During the cooking process, starch build up will form on the temperature
probes, tank and heating element. If you are producing high quantities of pasta it may be necessary
to clean these components more then once a day.
WARNING
The power supply must be disconnected before cleaning and servicing this appliance!
3.1.1. APPLIANCE INSPECTION
ü
Check that the high temperature limit, temperature probe and elements are in the correct
position and secured in place.
ü
ü
Check that wires and cords are not frayed or loose in and out of the cabinet.
Check around the appliance for loose parts or accessories that need to be secured or other
foreign items (ex: Aerosol cans) that should be removed from the area.
ü
Check for water leaks around the drain lines and water supply in and out of the cabinet and
around the appliance.
WARNING
Wear protective gloves and clothing when cleaning and draining the appliance and
when disposing of water. The water is extremely hot and can cause severe injuries.
3.1.2. CLEANING THE COOK TANK (RINSE TANK IF EQUIPPED)
1. Turn the appliance off.
WARNING
Read the operation section of this manual prior to filling or operating the appliance.
2. Scrub the tank, basket hanger, baskets, heating element and temperature probe using a
Scotchbrite™ or other abrasive pad with a commercial type cleaner specifically designed for
cleaning and sanitizing food contact surfaces. Follow the directions and familiarize yourself
with the safe use of this cleaner prior to using it to clean the appliance. Care must be taken
to remove all the foreign material on the tank and on components in the tank.
WARNING
DO NOT leave the appliance unattended during cleaning.
3. When cleaning is complete, rinse the inside of the tank and its components thoroughly with
cool water. Continue to rinse at least twice or until the cleaner has been completely and
thoroughly rinsed from the tank.
3.1.3. CLEANING THE CABINET
1. The inside of the cabinet should be cleaned with a clean dry cloth removing oil, dust, dirt and
cooking debris on all accessible surfaces and components.
2. The outside of the cabinet should be cleaned with a wetted cloth and mild detergent to
remove oil, dust, dirt and debris. Be careful not to introduce the detergent into the tank and
food zone regions of the appliance.
11
PREVENTATIVE MAINTENANCE
3.2. MONTHLY PREVENTATIVE MAINTENANCE
Water can leave mineral deposits inside the tank. Performing the monthly preventative maintenance
steps below will keep your equipment safe and at peak performance. If you are producing high
quantities of pasta or your water is heavily mineral based, then it may be necessary to clean these
components more then once a month.
3.2.1. DELIMING
1. Read the “operation” section of this manual prior to filling or operating the appliance.
2. Following the manufacturer’s deliming instructions, remove deposits from the tank’s interior.
3. When cleaning is complete, rinse the inside of the tank and its components thoroughly with
cool water. Continue to rinse at least twice or until the cleaner has been completely and
thoroughly rinsed from the tank.
4. Using a clean dry cloth, wipe out all of the water.
5. Repeat the previous steps to clean the rinse tank (if equipped).
3.3. ANNUAL/PERIODIC PREVENTATIVE MAINTENANCE AND INSPECTION
This section should ONLY be performed by a qualified service technician as part of a regular kitchen
maintenance program. This inspection should take place a minimum of once a year by an Authorized
Service Technician recommended by Pitco. It may be
WARNING
necessary perform this inspection more then once a year.
The power supply must be
disconnected before cleaning
and servicing this appliance!
3.3.1. HEATING ELEMENT
ü
Check if the element is mechanically strong and in
good condition. Look for scale build up and inspect for
signs of repeated dry firing.
ü
ü
ü
Verify element wires are in good working condition. Look for damage to wires or frayed
insulation. Check that the insulation is dry.
Verify that bulkhead connections/nut is tight and leak free. Look for water stains and wet
surfaces.
Verify amp-draw is within range as compared to the information on the data plate.
3.3.2. TEMPERATURE PROBE & HIGH LIMIT PROBE
ü
Verify probes are in good working condition. Check for damage and that the fasteners are
tightly secured to the tank.
ü
ü
Verify compression fittings are leak free.
Check wiring for loose electrical connections.
3.3.3. CONTROLLER
Perform the following inspection if the appliance is equipped with a temperature controller.
ü
Verify that the controller is in good mechanical condition. Check all lights, displays and
switches to assure that they are working properly. Examine overlay for damage that could
allow moisture to enter.
ü
ü
Check for loose electrical connections.
Verify simmer temperature. Check temperature 1” above controller probe, if necessary check
probe resistance.
ü
Check drain valve interlock (if provided) to ensure that the appliance stops heating when the
drain valve is open.
12
L20-293, rev. 0 (1/06)
PE14D: Floor Model Electric Pasta Cooker
PREVENTATIVE MAINTENANCE
3.3.4. CONTROL BOX & ELECTRICAL COMPONENTS
ü
Verify that heating contactors are in good condition. Check for worn or pitted contacts. Verify
that wires are tight and in good condition.
ü
Verify that all components (transformer, terminal block, relays, drain switches, etc…) are in
good condition. Verify that wires are tight and in good condition.
Verify enclosures are free of leaks. Check for water stains and wet surfaces.
Verify that the covers and panels are in tact and provide a safe condition. Check for loose
parts.
ü
ü
ü
Verify power cord is in good condition. Check for frayed or exposed wires. Verify that the
insulation is in good condition and the attachment to the appliance is tight.
3.3.5. TANK
Verify that the tank is in good condition. Check for scale build up and inspect for signs of
ü
corrosion. Verify that tank is leak free. Check drain overflow (if equipped) for scale build up
and debris blockage.
3.3.6. DRAIN SYSTEM
ü
ü
Verify that drain valve is in good condition. Check for leaks in the seal area and fitting region.
Verify that drain lines are leak free, kink free and in good condition. Check for scale build up
and debris blockage. Verify that the clamps and connections are securely tightened.
13
TROUBLESHOOTING
4. TROUBLESHOOTING
4.1. POWER FAILURE
If electric power is removed for any reason, the appliance will shut down To restart the appliance,
follow the appliance start up procedure in section 2.2.
4.2. HIGH TEMPERATURE LIMIT
This appliance is equipped with a high temperature limit switch. The high temperature limit switch will
stop the appliance from functioning if the internal cook tank reaches an unsafe temperature. In the
event that the high temperature limit has tripped, Please refer to the following procedure to reset the
switch.
1. Turn the appliance off.
2. Allow the appliance ample time to cool to room
temperature.
3. Add water to the cook tank as needed.
4. Press the high temperature reset button if equipped.
High Temperature Reset Button
5. The high limit switch is now reset and the appliance is
(Not on all models)
ready for start up.
WARNING
DO NOT add water to the tank until it has been given ample time to cool down. Failure
to do so may result in damage to the appliance and/or injury to the operator.
4.3. DRAIN VALVE INTERLOCK
If your appliance is equipped with a drain valve interlock circuit, the appliance will stop heating if the
tank drain valve is opened. In some cases the appliance will turn off. Refer to the following
procedure to resume operation after the drain valve interlock is tripped.
1. Turn the appliance OFF (if not already OFF).
2. Close the tank drain valve and fill the tank with water.
3. Turn the appliance ON.
14
L20-293, rev. 0 (1/06)
PE14D: Floor Model Electric Pasta Cooker
4.4. TROUBLESHOOTING CHART
TROUBLESHOOTING
Problem
Probable Causes
No power to appliance.
Circuit Breaker tripped.
Corrective Actions
Check main building power supply.
Reset circuit breaker.
Flip I/0 switch to I position and turn
on controller.
Turn on controller.
Controller does not
activate.
I/0 Switch in 0 position.
Controller not turned on.
Power Cord loose or not connected. Connect power cord.
Allow appliance to cool and reset
High temperature limit.
Controller displays
that it is heating but
water will not heat.
High temperature limit has tripped
4.5. CONTROLLER WARNING DISPLAYS
If your appliance is equipped with a temperature controller it may display the following warnings on its
display.
Display
Problem
Action
Water temperature Wait for appliance to heat up.
is low.
Incorrect probe
reading.
Contact Authorized Service Company.
Water level is low.
Turn off appliance. Allow ample time for appliance to
cool before filling with water and turning on.
Incorrect probe
reading.
Contact Authorized Service Company.
Drain valve is open Turn off appliance. Close drain valve before turning
while controller is
appliance back on.
on.
15
In the event of problems with or
questions about your order, please
contact the Pitco Frialator factory at:
(800) 258-3708 US and Canada only or
(603) 225-6684 World Wide
In the event of problems with or questions
about your equipment, please contact the
Pitco FrialatorAuthorized Service and Parts
representative (ASAP) covering your area, or
contact Pitco at the numbers listed to the left.
MAILING ADDRESS – P.O. BOX 501, CONCORD, NH 03302-0501
SHIPPING ADDRESS – 10 FERRY ST., CONCORD, NH 03301
L20-293, rev. 0 (1/06)
|