Scotts Spreader CD36C User Guide

Prizelawn CD36C  
®
COMMERCIAL DROP SPREADER  
MODEL CD36C  
OWNER’S MANUAL  
 
Operation  
1. Before filling Hopper, make sure spreader  
Handle Lever is in the “OFF” position. Always fill  
spreader on walk or drive, not on the lawn.  
4. Operate spreader at 3 MPH pace.  
(33.3 feet in 7.5 seconds)  
5. Apply two header strips at each end  
of area to treated and then proceed  
lengthwise between the header strips.  
Be sure to overlap the wheel tracks  
slightly to prevent streaking.  
2. Loosen Rate Control Knobs and move the Tie  
Bar to setting recommended for the product  
applied. If PrizeLAWN settings are not available,  
use Scotts® drop spreader settings. If setting is not  
known, refer to “DETERMINING APPLICATION  
RATES” section of this book. Retighten knobs after  
setting is made.  
6. When applying lime, do not use lime-  
stone that is so finely ground that it will  
pack inside the Hopper, or use hard,  
abrasive particles which will damage  
the spreader.  
3. Always push spreader, do not pull.  
Start spreader in motion and as it passes  
over the area to be treated, push Handle  
Lever to the “ON” position. Close Handle  
Handle Lever at the end of each pass.  
Use only compacted, free flowing, non-  
abrasive lime products.  
Determining Application  
Rates For Drop Spreaders  
Maintenance  
The following procedure provides a means of accurately  
determining drop spreader settings when settings do not  
appear on the package, or to “fine tune” the manufacturer’s  
recommend settings. Spreader rates can vary due to  
walking speed, condition of turf. humidity, physical characteristics  
of the product being applied, or condition of the spreader. It is  
good practice to double check settings using the following  
method:  
1. Never store unused material in spreader. Return  
unused product to its original container.  
2. Set Rate Slide on the highest number, open  
spreader and spin Wheels to remove excess material.  
3. Wash out Hopper thoroughly after each use to  
remove material clinging to surfaces. Pay close  
attention to area between the Shutoff Bar and Hopper.  
Allow spreader to completely dry.  
PROCEDURE  
EXAMPLE  
1. The manufacturer will recommend  
coverages on the product package.  
Generally, it is stated as applying  
a certain number of pounds of  
The contents of this  
package (25 lbs.)  
covers 2,000 square  
feet.  
4. Oil bottom of Hopper, Control Housing Spring and  
Agitators at the Center Bearing. Lubricate Axle  
Bearings with grease. Store spreader in open position.  
product per 1,000 square feet.  
2. Determine the amount of material  
in pounds to cover 100 square  
feet. Add two zeros to weight  
of bag and divide that by the  
square foot coverage.  
2,500 divided by 2,000  
square feet= 1.25 lbs.  
“Open”  
Oil  
Oil  
3. To change the decimal portion  
of answer in step #2 to ounces,  
multiply decimal portion by 16.  
0.25 x 16 oz. = 4 oz.  
Total weight = 1 lb.- 4 oz.  
4. On a clean walk of driveway, measure out 33.3 feet- the  
distance required to cover 100 square feet.  
5. Add a measured amount of product to the spreader- 2 to 3  
times the recommended rate. Operate spreader at a brisk walking  
speed (3 mph of 33.3 feet in 5. sec.) over the measured distance.  
Empty the spreader and weigh the amount left. Compare with the  
beginning amount; the difference is the amount applied. Adjust the  
setting up or down to achieve the correct application rate.  
Grease  
Oil  
Grease  
Scotts® is a registered trademark of The Scotts Company  
 
Parts List for Model CD36C  
19  
24  
20  
15  
24  
18  
21  
17  
14  
16  
13  
12  
1
22  
2
11  
3RH  
4
6
7
9
5
23  
3LH  
10  
8
ITEM  
1
2
3 RH.  
3 LH.  
4
5
6
7
8
PART #  
14211-1  
14414-2  
14643-1  
14644-1  
14231  
14235  
14227  
14007  
14222-1  
90005  
14006  
15032  
12714  
12704  
14237  
14286  
12708  
15029-1  
15046  
14047  
14870  
14415-1  
14409  
15066  
14236  
DESCRIPTION  
HOPPER ASSEMBLY  
SHUTOFF BAR ASSEMBLY*  
AGITATOR/AXLE ASSEMBLY-LH. *  
AGITATOR/AXLE ASSEMBLY-RH.*  
BEARING SUPPORT ASSEMBLY*  
AGITATOR BAFFLE* (2)  
END HANGER* (2)  
AXLE GREASE SEAL* (2)  
PLATE ASSEMBLY-BEARING END* (2)  
GREASE FITTING* (2)  
AXLE BEARING* (2)  
WHEEL & TIRE ASSEMBLY (2)  
LEG (2)  
RATE CONTROL KNOB* (2)  
TIE BAR*  
SPRING HOUSING ASSEMBLY* (2)  
POINTER*  
PART OF OUR SERVICE IS PROVIDING  
REPLACEMENT PARTS. Parts may be  
obtained through your local distributor.  
Be sure to give:  
1. SPREADER MODEL NUMBER  
2. SPREADER NAME  
3. PART NUMBER  
4. NAME OF PART AS SHOWN  
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
IF YOUR LOCAL  
DISTRIBUTOR CANNOT  
SUPPLY PARTS,  
CONTACT:  
HANDLE BRACE  
UPPER HANDLE ASSEMBLY  
HANDLE LEVER ASSEMBLY W/ CHAIN  
HANDLE GRIP (2)  
CONTROL TUBE  
PSB Company  
555 West Goodale Street P.O. Box 1089  
Columbus, Ohio 43216-1089  
614-228-5781 EXT. 2655  
CONTROL TUBE BRACE (2)  
FASTENER PACKAGE  
RATE PLATE* (2)  
15063  
PARTS PACKAGE (NOT SHOWN)  
*Parts included in hopper assembly  
© 2003 PSB COMPANY  
 

Quantum Data Projector 822S User Guide
Raymarine GPS Receiver Ray54E User Guide
ResMed Network Card 608140 20611 User Guide
Rinnai Water Heater REU V2526W US User Guide
Roland Electronic Keyboard HPi 6F User Guide
Rosewill Computer Hardware RC214 User Guide
Rosewill Network Card RNX N150PCe User Guide
Ruud Water Heater AP13370 2 User Guide
Samsung Tablet 700T1AA06 User Guide
Sceptre Technologies Flat Panel Television E248 User Guide