Low Profile Universal TV Mount - 32" to 60"
Installation Instructions
Fixed LCD / TFT TV Wall Mount
Material: 2.0mm Cold Rolled Steel Plate
TV Size: 32" - 60"
Max load capacity:165 lbs / 75 kgs
Wall distance: 30mm / 1.2"
Bubble level system included
Universal Mounting Pattern
IMPORTANT: If you don't understand the installation instructions, please consult an installation
specialist
04-0528C
1
Tools Required:
Phillips head screw driver
1
2
3
4
Stud finder for drywall installation
5/16" Socket and Wrench
Electric drill and 5/16" (8mm) masonry bit for concrete/brick installation
Note: Please ensure that the bubble level is properly mounted on the wall plate prior to mounting the wall
plate.
Step1: Wall Plate Installation
a) Wood Stud Installation
NOTE: When mounting to wood studs, the two wood studs must be a minimum of 16" apart.
1
2
Use a high-quality electronic stud finder (commercially available) to
locate dead center of two studs and mark their locations with a pencil
(figure 1-a).
With the help of an assistant, and using the bubble level to ensure the
wall plate is level, position the wall plate against the wall in the desired
mounting location.
Mark the right (upper and lower) and the left (upper and lower) positions
3
of the small horizontalslots that are in alignmentwith the studs (figure 1-
b).
You should mark four positions total.
4
5
Next, pre-drill a 1/4" hole to a depth of 2" in the wall stud at each
marked location.
Place the wall plate against the wall and line up the mounting slots with the drilled holes. Check the bubble level to verify
that the wall plate is level.
6
For each location, insert a lag bolt (J) and washer (L) into the wall
7
8
Tighten the bolt with an open ended socket wrench by turning clockwise until tight.
CAUTION: Do not over-tighten bolts-doing so many cause unnecessary damage to the wall. Avoid excessive torque.
CAUTION: Do not release the wall plate until it is properly mounted and secured to the wall.
3
b) Concrete/Brick Installation
The concrete anchors must be used for concrete installation.
NOTE:
Begin by placing the wall plate into position against the wall, using the bubble level to keep it level.
Mark four holes to be used for securing the mount and place the wall plate aside.
Next, drill holes using an electric drill and 5/16" masonry bit to a depth of 2".
Insert a concrete anchor into each hole.
1
2
3
4
5
6
7
8
If necessary, a hammer can be used to lightly tap each anchor into place so that they are flush with the wall.
Once all of the anchors are in place, move the wall plate back into position
Insert bolt (J) with washer (L) into each concrete anchor in the wall.
Do not tighten until all screws are in place.
Step 2 Display Bracket Installation
1
2
To ensure optimal installation, this kit includes various screws of
different diameters and lengths.
Place your TV screen down on a soft, flat surface, and locate the
threaded mounting points that are located on the back of the display.
3
4
Determine which screw (A/B/C/D/E/F/G/H) is of the correct length by
carefully inserting a straw, or toothpick, and mark how deep the
mounting point is.
If your display has a curved back or a recessed thread mounting point, a spacer (M) must be used. Then choose screw
(F/G/H) to match.
5
6
Place the spacer (M) between the mounting bracket and display.
According to the size of display's hole, choose the corresponding screw and hole on the rectangle washer, then thread
them in line as shown (figure 2-a)
Step 3 Final Installation & Adjustment
1
2
Hook the TV Rails over the top of the wall plate (figure 3-a).
Then rotate the long screw at the bottom of the display rail to tighten.
Maintenance
Check the mounting screws every two months for tightness.
4
Blank Page
5
Blank Page
6
Technical Support and Warranty
QUESTIONS? SIIG’s Online Support has answers! Simply visit our web site at www.siig.com and click Support. Our onlinesupport
database is updated daily with new drivers and solutions. Answers to your questions could be just a few clicks away. You can also
submit questions online and a technical support analysts will promptly respond.
SIIG offers a 5-year manufacturer warranty with this product. This warranty covers the originalpurchaser and guarantees the product
to be free of any defects in materials or workmanship for five (5) years from the date of purchase of the product.
SIIG will, at our discretion, repair or replace (with an identicalproduct or product having similar features and functionality)the product if
defective in materials or workmanship. This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state. Please see our web site for more warranty details.
If you encounter any problems with this product, please follow the procedures below.
A) If it is within the store's return policy period, please return the product to the store where you purchased from.
B) If your purchase has passed the store's return policy period, please follow these steps to have the product repaired or replaced.
Step 1: Submit your RMA request.
Go to www.siig.com, click Support, then click RMA to submit a request to SIIG RMA or fax a request to 510-657-5962. If the product
is determined to be defective, an RMA number will be issued.
Step 2: After obtaining an RMA number, ship the product.
• Properly pack the product for shipping. All software, cable(s) and any other accessories that came with the originalpackage must be
included.
• Clearly write your RMA number on the top of the returned package. SIIG will refuse to accept any shipping package, and will not be
responsible for a product returned without an RMA number posted on the outside of the shipping carton.
• You are responsible for the cost of shipping to SIIG. Ship the product to the following address:
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
RMA #: ________________
• SIIG will ship the repairedor replacedproduct via Ground in the U.S. and InternationalEconomy outside of the U.S. at no cost to the
customer.
7
About SIIG, Inc.
Founded in 1985, SIIG, Inc. is a leading manufacturer of IT connectivity solutions (including Serial ATA and Ultra
ATA Controllers, FireWire, USB, and legacy I/O adapters) that bridge the connection between Desktop/Notebook
systems and external peripherals. SIIG continues to grow by adding A/V and Digital Signage connectivity solutions
to our extensive portfolio. All centered around the distribution and switching of A/V signals over CAT5/6, these
products include matrix switches, distribution amplifiers, extenders, converters, splitters, cabling, and more.
SIIG is the premier one-stop source of upgrades and is committed to providing high quality products while keeping
economical and competitive prices. High-quality control standards are evident by one of the lowest defective return
rates in the industry. Our products offer comprehensive user manuals, user-friendly features, and most products are
backed by a lifetime warranty.
SIIG products can be found in many computer retail stores, mail order catalogs, and e-commerce sites in the
Americas, as well as through major distributors, system integrators, and VARs.
PRODUCT NAME
Low Profile Universal TV Mount - 32" to 60"
Low Profile Universal TV Mount - 32" to 64" is a trademark of SIIG, Inc. SIIG and the SIIG logo are registered trademarks of SIIG, Inc. Other
names used in this publication are for identification only and may be trademarks of their respective owners.
September, 2010
Copyright © 2010 by SIIG, Inc. All rights reserved.
8
|