Sylvania TV VCR Combo RSEC313E User Manual

OWNER’S

MANUAL

SYLVANIA

13-INCH COLOR TV/VCR

RSEC313E

INSTRUCCIONES EN ESPAÑOL INCLUIDAS.

As an ENERGY STAR^®

Partner, our company has

determined that this product meets

the ENERGY STAR^®guidelines for

energy efficiency. ENERGY STAR^®

is a U.S. registered mark.

If you need additional assistance for set-up or operating after

reading owner’s manual, please call TOLL FREE : 1-800-968-3429.

Please read before using this equipment

FIGURE A

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE

ANTENNA

LEAD I N

WI RE

GROUND

CL AMP

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

ELECTRI C

SERVICE

EQUIPMENT

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

NEC

NATIONAL ELECTRICAL CODE

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

S2898A

13. Outdoor Antenna grounding-If an outside antenna or

cable system is connected to the TV/VCR, be sure the

antenna or cable system is grounded so as to provide

some protection against voltage surges and built-up static

charges. Article 810 of the National Electrical Code,

ANSI/NFPA No. 70, provides information with respect to

proper grounding of the mast and supporting structure,

grounding of the lead-in wire to an antenna discharge

unit, size of grounding conductors, location of antenna-

discharge unit, connection to grounding electrodes, and

requirements for the grounding electrode. (Fig. A)

19. Damage Requiring Service-Unplug this TV/VCR from

the wall outlet and refer servicing to qualified service per-

sonnel under the following conditions:

a. When the power-supply cord or plug is damaged or

frayed.

b. If liquid has been spilled, or objects have fallen into the

TV/VCR.

c. If the TV/VCR has been exposed to rain or water.

d. If the TV/VCR does not operate normally by following

the operating instructions. Adjust only those controls that

are covered by the operating instructions, as improper

adjustment of other controls may result in damage and

will often require extensive work by a qualified technician

to restore the TV/VCR to its normal operation.

14. Lightning-For added protection for this TV/VCR receiv-

er during a lightning storm, or when it is left unattended

and unused for long periods of time, unplug it from the

wall outlet and disconnect the antenna or cable system.

This will prevent damage to the TV/VCR due to lightning

and power-line surges.

e. If the TV/VCR has been dropped or damaged in any way.

f. When the TV/VCR exhibits a distinct change in perfor-

mance-this indicates a need for service.

15. Power Lines-An outside antenna system should not be

located in the vicinity of overhead power lines or other

electric light or power circuits, or where it can fall into

such power lines or circuits. When installing an outside

antenna system, extreme care should be taken to keep

from touching such power lines or circuits as contact with

them might be fatal.

20. Replacement Parts-When replacement parts are required,

be sure the service technician has used replacement parts

specified by the manufacturer that have the same charac-

teristics as the original part. Unauthorized substitutions

may result in fire, electric shock, injury to persons or

other hazards.

16. Overloading-Do not overload wall outlets and extension

21. Safety Check-Upon completion of any service or repairs

to this TV/VCR, ask the service technician to perform

routine safety checks to determine that the TV/VCR is in

proper operating condition.

cords as this can result in a risk of fire or electric shock.

17. Object and Liquid Entry-Never push objects of any kind

into this TV/VCR through openings as they may touch

dangerous voltage points or short out parts that could

result in a fire or electric shock. Never spill liquid of any

kind on the TV/VCR.

22. Heat-This TV/VCR product should be situated away from

heat sources such as radiators, heat registers, stoves, or

other products (including amplifiers) that produce heat.

18. Servicing-Do not attempt to service this TV/VCR your-

self as opening or removing covers may expose you to

dangerous voltage or other hazards. Refer all servicing to

qualified service personnel.

CAUTION:TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY

INSERT.

ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE

LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

- 3 -

9I03

PRECAUTIONS

IMPORTANT COPYRIGHT INFORMATION

LOCATION

For safe operation and satisfactory performance of

your TV/VCR, keep the following in mind when

selecting a place for its installation:

Shield it from direct sunlight and keep it away

from sources of intense heat.

Avoid dusty or humid places.

Avoid places with insufficient ventilation for proper

heat dissipation. Do not block the ventilation holes

at the top or bottom of the unit. Do not place the

unit on a carpet because this will block the ventila-

tion holes.

Unauthorized recording or use of broadcast televi-

sion programming, video tape, film or other copy-

righted material may violate applicable copyright

laws. We assume no responsibility for the unautho-

rized duplication, use, or other acts which infringe

upon the rights of copyright owners.

•

FCC WARNING- This equipment may gener-

ate or use radio frequency energy. Changes or

modifications to this equipment may cause

harmful interference unless the modifications

are expressly approved in the instruction man-

ual. The user could lose the authority to oper-

ate this equipment if an unauthorized change

or modification is made.

Install unit in a horizontal position.

Avoid locations subject to strong vibration.

Do not place the TV/VCR near strong magnetic fields.

Avoid moving TV/VCR to locations where temper-

•

ature differences are extreme.

This equipment has been tested and found to com-

ply with the limits for a Class B digital device, pur-

suant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and

used in accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference to

radio or television reception, which can be deter-

mined by turning the equipment off and on, the

user is encouraged to try to correct the interfer-

ence by one or more of the following measures:

1) Reorient or relocate the receiving antenna.

2) Increase the separation between the equipment

and receiver.

AVOID THE HAZARDS OF

ELECTRICAL SHOCK AND FIRE

•

Do not handle the power cord with wet hands.

Do not pull on the power cord when disconnecting

it from an AC wall outlet. Grasp it by the plug.

If by accident, water is spilled on your unit, unplug

the power cord immediately and take the unit to our

Authorized Service Center for servicing.

Do not put your fingers or objects into the

TV/VCR cassette holder.

Do not place anything directly on top of the unit.

•

WARNING

Moisture condensation may occur inside the unit

when it is moved from a cold place to a warm place

or after heating a cold room or under conditions of

high humidity. If a tape is played in a TV/VCR

which has moisture, it may damage the tape and

TV/VCR. Therefore when the condensation occurs

inside the unit, turn the POWER button on and allow

at least 2 hours for the unit to dry out.

3) Connect the equipment into an outlet on a cir-

cuit different from that to which the receiver is

connected.

4) Consult the dealer or an experienced radio/TV

technician for help.

The serial number of this product may be found on the back of the unit. No other TV/VCR has the same serial

number as yours. You should record the number and other vital information here and retain this book as a per-

manent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.

Date of Purchase

Dealer Purchase from

Dealer Address

Dealer Phone No.

Model No.

Serial No.

- 4 -

9I03

TABLE OF CONTENTS

C IMPORTANT SAFEGUARDS . . . . . . . . . . . . .2

C PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . .17

NORMAL PLAYBACK . . . . . . . . . . . . . . . . . .17

AUTO REPEAT PLAYBACK . . . . . . . . . . . . .17

SEARCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

STILL PICTURE . . . . . . . . . . . . . . . . . . . . . . .18

PICTURE CONTROLS . . . . . . . . . . . . . . . . . .19

C PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . .4

LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

AVOID THE HAZARDS OF ELECTRICAL

SHOCK AND FIRE . . . . . . . . . . . . . . . . . . . . . .4

WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

C FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

C SUPPLIED ACCESSORIES . . . . . . . . . . . . . . .6

C OPERATING CONTROLS AND FUNCTIONS 7

C RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .19

NORMAL RECORDING . . . . . . . . . . . . . . . . .20

SKIPPING UNWANTED SCENES DURING

RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .20

OTR (One Touch Recording) . . . . . . . . . . . . . .20

TIMER RECORDING . . . . . . . . . . . . . . . . . . .21

TIMER PROGRAM EXTENSION . . . . . . . . .22

C PREPARATION FOR USE . . . . . . . . . . . . . . . .9

ANTENNA/CABLE CONNECTIONS . . . . . . .9

EXTERNAL INPUT MODE . . . . . . . . . . . . . .10

INSTALLING THE BATTERIES . . . . . . . . . . .10

HINTS FOR AUTOMATIC TIMER

RECORDING . . . . . . . . . . . . . . . . . . . . . . . . .23

C SET UP FOR USE . . . . . . . . . . . . . . . . . . . . .10

SELECTING THE LANGUAGE . . . . . . . . . . .10

CLOCK SET UP (AUTO / MANUAL) . . . . . .10

DAYLIGHT-SAVING TIME . . . . . . . . . . . . . .12

CHANNEL SET UP . . . . . . . . . . . . . . . . . . . .13

DELETING (OR ADDING) CHANNEL(S) . . .13

AUTO RETURN . . . . . . . . . . . . . . . . . . . . . . .23

WAKE UP TIMER . . . . . . . . . . . . . . . . . . . . . .23

SLEEP TIMER . . . . . . . . . . . . . . . . . . . . . . . . .24

C COPYING A VIDEO TAPE . . . . . . . . . . . . . . .24

C ON SCREEN DISPLAY . . . . . . . . . . . . . . . . .25

C SPECIAL FEATURES . . . . . . . . . . . . . . . . . .25

REAL TIME TAPE COUNTER . . . . . . . . . . . .25

AUTO REWIND-EJECT . . . . . . . . . . . . . . . . .25

C TV OPERATION . . . . . . . . . . . . . . . . . . . . . . .14

WATCHING A TV PROGRAM . . . . . . . . . . . .14

GAME MODE . . . . . . . . . . . . . . . . . . . . . . . . .14

DEGAUSSING . . . . . . . . . . . . . . . . . . . . . . . .14

PICTURE CONTROL . . . . . . . . . . . . . . . . . . .14

CLOSED CAPTION SYSTEM . . . . . . . . . . . .15

V-CHIP SET UP . . . . . . . . . . . . . . . . . . . . . . . .15

C MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . .25

C TROUBLESHOOTING GUIDE . . . . . . . . . . .26

C SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . .27

C CABLE CHANNEL DESIGNATIONS . . . . . .27

C WARRANTY . . . . . . . . . . . . . . . . . . .Back Cover

INDICE

CONTROLES DE OPERACIÓN Y

SUS FUNCIONES . . . . . . . . . . . . . . . . . . . . . . . .28

SELECCION DE IDIOMA . . . . . . . . . . . . . . . . .30

AJUSTE DE CANAL . . . . . . . . . . . . . . . . . . . . .31

AJUSTE DEL RELOJ . . . . . . . . . . . . . . . . . . . . .31

CONEXIONES DE ANTENA/CABLE . . . . . . . .30

MODO DE ENTRADA EXTERNA . . . . . . . . . . .30

A NOTE ABOUT RECYCLING

This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in

accordance with your local recycling regulations.

Batteries should never be thrown away or incinerated but disposed of in accordance with your local regula-

tions concerning chemical wastes.

- 5 -

9I03

FEATURES

Infrared remote control

Trilingual on screen menu display selectable in

English, Spanish, or French

Zero Return–The tape returns to counter of

•

0:00:00 by rewinding or fast forwarding.

Still–Freeze the picture at any time, for close view-

ing of a particular scene. Only tapes recorded in

SLP mode will show a fairly clear picture.

Digital Auto Tracking (DTR)–Automatically

adjusts the tracking for each tape you play.

Rental play mode–Improves playback picture

quality from worn tapes, such as rental tapes.

Auto repeat–Allows you to repeat the playing of a

tape indefinitely without pressing the PLAY button.

Time search–Lets you set the TV/VCR to advance

the tape by entering the desired playback time you

want to skip.

OTR (One Touch Recording)–Instant timed

recording from 30 to 480 minutes is possible at the

push of the REC/OTR button.

1 Year, 8 events (including Daily and Weekly

Timer Recording)–The built-in timer allows you to

record up to 8 programs at different times on dif-

ferent channels up to 1 year in advance. The Daily

timer allows recordings to be made of daily broad-

casts and the Weekly timer allows recording to be

made once a week up to the end of the tape.

Real time counter–This shows the elapsed record-

ing or playback time in hours, minutes and sec-

onds. The “–” indication will appear when the tape

is rewound further than the tape counter position

“0:00:00”.

181 channel capability PLL frequency synthesiz-

er tuner with direct station call–(A converter may

be necessary to view scrambled cable channels.)

Auto Clock Setting–Allows you to set the clock

function from a PBS broadcast station.

Closed caption system–You may view specially

labeled (cc) TV programs, movies, news, prere-

corded tapes, etc. with either a dialogue caption or

text display added to the program.

Game mode–Automatically sets external input

mode and allows TV/VCR display to be suitable

for use with TV games.

Auto power on and off system–Automatically

turns on the TV/VCR when you insert the cassette,

turns off after auto-rewind and ejects when the

beginning of the tape is reached.

•

Auto rewind when the end of a tape is

reached–This function doesn’t occur when using

timer recording.

2 Step picture search operation–You can view a

video program at a high speed or super high speed

in either a forward or reverse direction in LP and

SLP mode. For SP mode only high speed.

Three different playback tape speeds : SP/LP/SLP

Two different recording tape speeds : SP/SLP

Auto Head Cleaner–Automatically cleans video

heads as you insert or remove a cassette.

Auto return–After timer recording is finished, the

TV/VCR can return to the beginning of the record-

ing.

Wake up/Sleep timer–Allows you to have the

TV/VCR automatically turn on or off at a desired

time.

Timer Program Extension–Allows you to shift the

time schedule for automatic timer recording.

V-CHIP–Enables parents to prevent their children

from watching inappropriate material on TV.

•

SUPPLIED ACCESSORIES

Remote Control Unit

PART NO. (NE145UD)

2 AA Batteries

Rod Antenna

PART NO. (0EMN00673 or

0EMN01599 or 0EMN01755)

If you need to replace these accessories, please refer to the PART NO. under the illustrations and call 1-800-

968-3429.

Depending on your antenna system, you may need different types of Combiners (Mixer) or Separators

(Splitter). Contact your local electronics store for these items.

We do not recommend the use of universal remote controls. Not all of the functions may be controlled with

a universal remote control. If you decide to use a universal remote control with this unit, please be aware

that the code number given may not operate this unit. In this case, please call the manufacturer of the uni-

versal remote control.

•

- 6 -

9I03

OPERATING CONTROLS AND FUNCTIONS

NOTE:

We do not recommend the use of universal remote controls. Not all of the functions may be controlled with

a universal remote control.

•

If you decide to use a universal remote control with this unit, please be aware that the code number given

may not operate this unit. In this case, please call the manufacturer of the universal remote control.

- TV/VCR FRONT PANEL -

VIDEO

AUDIO

POWER

VOLUME

CHANNEL

STOP/EJECT REW

PLAY

F.FWD

REC/OTR

EARPHONE

1 2

7 8 9

11 12

- REMOTE CONTROL -

1 VIDEO input jack– Connect to the video output

jack of your video camera or another VCR.

2 AUDIO input jack– Connect to the audio output

jack of your audio equipment, video camera or

another VCR.

WAKE-UP

/SLEEP

POWER

EJECT

CHANNEL

RETURN

3 POWER button– Press to turn TV/VCR on and

off. Press to activate timer recording.

4 VOLUME X / Y buttons– Adjust the volume level.

5 CHANNEL K / L buttons– Press to select the

desired channels for viewing or recording.

You may display the main menu on the TV screen

by pressing repeatedly this button on the TV/VCR.

TRACKING function– Press to minimize video

‘noise’ (lines or dots on screen) during playback

mode. (See page 19.)

CHANNEL

VOLUME

+100

DISPLAY

MUTE

PLAY

REW

F.FWD

6 Remote Sensor Window– Receives the infrared

signals from the remote control.

STOP

SPEED PAUSE/STILL

RECORD

7 EJECT button– Press in the Stop mode to remove

tape from TV/VCR.

STOP button– Press to stop the tape motion.

L button–

T-PROG.

CLEAR

GAME

TIME SEARCH

COUNTER

RESET

Press to select setting modes from the on

screen menu.

•

Press to enter digits when setting program.

(for example: setting clock or timer program)

•

- 7 -

9I03

- REAR VIEW -

ANT.

+100 button– When selecting cable channels

which are higher than 99, press this button first,

then press the last two digits. (To select channel

125, first press the “+100” button then press “2”

and “5”).

8 REW button– Press to rewind the tape, or to view

the picture rapidly in reverse during playback

mode. (Rewind Search)

s button–

Press to select a mode from a particular menu.

•

16 MENU button– Press to display the main menu on

the TV screen.

17 DISPLAY button– Display the counter or the cur-

rent channel number and current time on the TV

screen. (See page 25.)

(for example: LANGUAGE or USER’S SET UP)

9 PLAY button– Press to begin playback.

K button–

Press to select setting modes from the on

screen menu.

•

18 SPEED button– Press to choose the desired

recording speed:SP/SLP.

19 T-PROG. CLEAR button– Press to cancel a setting

of timer program. (See page 23.)

Press to enter digits when setting program.

•

(for example: setting clock or timer program)

10 F.FWD button– Press to rapidly advance the tape,

or to view the picture rapidly in forward during

playback mode. (Forward Search)

COUNTER RESET button– Press to reset counter

to 0:00:00.

B button–

20 GAME button– Sets the game mode and external

input mode at the same time. (See page 14.)

21 TIME SEARCH button– Press to activate Time

Search mode.

When setting program (for example: setting

•

clock or timer program), press to determine

your selection and proceed to the next step you

want to input.

Press to determine setting modes from on

screen menu.

Press to select a mode from a particular menu.

22 PAUSE/STILL button– Press to temporarily stop

the tape during the recording or to view a still pic-

ture during playback.

23 MUTE button– Mutes the sound. Press it again to

resume sound.

24 CHANNEL RETURN button– Press to go back to

the previously viewed channel. For example,

pressing this button once will change channel dis-

play from 3 (present channel) to 10 (previously

viewed channel), and pressing it a second time

will return from 10 to 3.

•

(for example: LANGUAGE or USER’S SET UP)

11 RECORD(REC) button– Press for manual recording.

OTR button– Activates One Touch Recording.

(only on the TV/VCR)

12 RECORD indicator– Flashes during recording.

Lights up in the Stand-by mode for Timer

Recording.

13 EARPHONE jack– Connects to earphones (not

supplied) for personal listening. The size of jack is

1/8” monaural (3.5mm).

25 WAKE-UP/SLEEP button– Sets the Wake up or

Sleep Timer. (See page 23.)

26 Power cord– Connect to a standard AC outlet

(120V/60Hz).

27 ANT. terminal– Connect to an antenna or cable

system.

14 Cassette compartment

15 Number buttons– Press to select desired channels

for viewing or recording. To select channels from

1 to 9, first press the 0 button and then 1 to 9.

- 8 -

9I03

PREPARATION FOR USE

ANTENNA/CABLE CONNECTIONS

From Cable System or

Satellite Dish

Rod Antenna

(Supplied)

VHF/UHF Antenna

(Not supplied)

Satellite Box or

Cable Box

OUT

(Not supplied)

VHF Antenna

(Not supplied)

UHF Antenna

(Not supplied)

From

Cable System

ANT

VHF/UHF Combiner

(Not supplied)

ANT.

75-ohm Coaxial

Cable (Not supplied)

Flat twin-lead cable

VHF/UHF COMBINED ANTENNA

VHF/UHF SEPARATE ANTENNAS

The VHF/UHF Rod Antenna (supplied) is detach-

able. Insert the stem of the antenna into the hole on

the upper-back portion of the TV/VCR. Connect the

VHF/UHF Rod Antenna or VHF/UHF Combination

Antenna to the ANT. terminal of the TV/VCR as

shown in the diagram above.

For the best reception, fully extend the VHF/UHF

Rod Antenna and make the necessary adjustments.

(Avoid touching the top section when adjusting.)

NOTE:

In some areas it will be necessary to use an outdoor

antenna.

CABLE WITHOUT CONVERTER/

DESCRAMBLER BOX

Use this connection if your cable system connects

directly to your TV/VCR without a converter box.

By using this connection you can:

1) Use the TV/VCR remote to select channels.

2) Program one or more unscrambled channels for

Automatic Timer Recording.

NOTE: This unit will ONLY record and view the

same channel.

Before plugging the Rod antenna into antenna termi-

nal, check that the pin is not bent. If it is bent,

straighten the pin as illustrated, then plug the pin into

antenna terminal.

CABLE WITH CONVERTER/

DESCRAMBLER BOX OR SATELLITE

BOX

Bent pin

If your cable service supplies you with a converter

box or if you use a satellite system, you can use the

basic connection shown here.

Cable Plug

(Straight pin)

(Needs to be straightened)

By using this connection you can also record scram-

bled channels. However, channel selection must be

made with the converter box or satellite box. This

means that channels cannot be changed using the

TV/VCR Remote Control. Unattended timer record-

ing is limited to one channel at a time.

NOTE:

The connection of an indoor antenna may not always

give acceptable TV reception.

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that

provides guidelines for proper grounding and in particular, specifies that the cable ground shall be connect-

ed to the grounding system of the building as close to the point of cable entry as practical.

- 9 -

9I03

TO RECORD A SCRAMBLED/UNSCRAMBLED

CHANNEL

INSTALLING THE BATTERIES

1. Set the TV/VCR channel selector to the output

channel of the Cable Converter Box or Satellite

Box. (Ex. CH3)

2. Select the channel to record from your Cable

Converter Box or Satellite Box.

1) Open the battery compartment cover by pressing

the cover on the remote unit in the direction of the

arrow.

2) Insert 2 “AA” penlight batteries into the battery

compartment in the direction indicated by the

polarity (+/-) markings.

3) Replace the cover.

EXTERNAL INPUT MODE

When using an external input signal (another VCR or

camcorder), connect the player’s audio/video output

cables to the AUDIO IN/ VIDEO IN jacks of your

TV/VCR. Then press the CHANNEL K or L button

until “AUX” appears on the screen.

AUX

NOTE: “AUX” is found below the

lowest memorized channel.

(Example: CH2)

SET UP FOR USE

4 Exit the Language mode

SELECTING THE LANGUAGE

Press the MENU button on the remote control to

return to TV mode.

1 Plug in the TV/VCR power cord

Plug the TV/VCR power cord into a

standard AC outlet.

NOTE: If for some reason the menu is in Spanish or

French, press the MENU button on the remote con-

trol, press the PLAY/K button to point to “IDIOMA

[ESPAÑOL]” or “LANGAGE [FRANÇAIS]”, then

press the F.FWD/B button, then press the MENU

button on the remote control.

NOTE:

If some digits appear in the corner of

•

the screen, press the POWER button

without unplugging the power cord.

Make sure ...

Press the POWER button to turn on the TV/VCR.

NOTE: This function effects only the language on

the screen menu and not the audio source.

•

– M E N U –

2 Select “LANGUAGE”

CLOCK SET UP

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

Press the MENU button on the

(AUTO / MANUAL)

remote control.

Press the PLAY/K or STOP/L but-

ton to point to “LANGUAGE”.

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

The TV/VCR clock must be set correctly before VCR

timer recording is possible. It is suggested that the

clock be set manually when first setting up the

TV/VCR, then set to [ON] the auto clock setting

which will periodically correct the setting if necessary.

NOTE: If you cannot receive a station with time

signals, auto clock setting cannot be performed. Use

manual setting only.

TIME SEARCH

3 Select “ENGLISH”, “ESPAÑOL” or

“FRANÇAIS”

Select “ENGLISH”, “ESPAÑOL”= Spanish or

“FRANÇAIS”= French using the F.FWD/B or

REW/s button.

- 10 -

9I03

MANUAL CLOCK SETTING

8 Start the clock

Make sure ...

Press the MENU button on the

remote control.

The TV/VCR is turned on.

In the example below, the clock is to be set to:

•

5:40 PM

Although seconds are not displayed,

they begin counting from 00 when

you press the MENU button on the

remote control. Use this feature to

synchronize the clock with the correct time.

NOTE:

When unplugging the AC cord or if there is a power

failure for more than 3 seconds, you may have to

reset the clock.

DATE

May 6th, 2004

SETTING TIME 5:40PM

1 Select “SETTING CLOCK”

Press the MENU button on the

remote control.

Press the PLAY/K or STOP/L

button to point to “SETTING

CLOCK”.

– M E N U –

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

TO CHANGE CLOCK SETTING

Then press the F.FWD/B button.

If you want to change the clock,

1) Follow steps [1] and [2].

2) Select where you want to change using the

F.FWD/B or REW/s button.

3) Enter correct numbers using the PLAY/K or

STOP/L button.

2 Select “MANUAL CLOCK SET”

Press the PLAY/K or STOP/L

button to point to “MANUAL

CLOCK SET”.

– SETTING CLOCK –

AUTO CLOCK

[ON]

AUTO CLOCK CH SEARCH

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[ 02 ]

[OFF]

Then press the F.FWD/B button.

4) Press the MENU button on the remote control to

start the clock.

– MANUAL CLOCK SET –

MONTH DAY YEAR

3 Select the month

Press the PLAY/K or STOP/L but-

ton until your desired month

appears. (Example: May → 05)

Then press the F.FWD/B button.

PLEASE NOTE:

0 5

– – – – – – – – –

If there is no local PBS station in your area or on

your cable system, select “AUTO CLOCK” and

press the F.FWD/B or REW/s button to turn [OFF]

this function. Then you can manually adjust the

clock.

HOUR

– –

MINUTE

– – – –

4 Select the day

Press the PLAY/K or STOP/L but-

ton until your desired day appears.

(Example: 6th → 06)

– MANUAL CLOCK SET –

MONTH DAY YEAR

AUTOMATIC CLOCK SETTING

Make sure ...

0 5

0 6 – – – – – – –

HOUR

– –

MINUTE

– – – –

The TV/VCR is turned on.

Confirm the TV/VCR is receiving a RF (Radio

Frequency) signal from either an antenna or cable

system connection using the ANT. terminal on the

rear of the TV/VCR.

•

Then press the F.FWD/B button.

5 Select the year

Press the PLAY/K or STOP/L but-

ton until your desired year appears.

(Example: 2004)

– MANUAL CLOCK SET –

MONTH DAY YEAR

0 5

0 6 THU 2 0 0 4

NOTE:

HOUR

– –

MINUTE

– – – –

If a cable converter box is being used, make sure it

is powered on.

•

Then press the F.FWD/B button.

You must use the TV/VCR remote control to per-

form the clock setting procedure.

•

6 Select the hour

– MANUAL CLOCK SET –

MONTH DAY YEAR

If the TV/VCR is connected directly to a cable

•

Press the PLAY/K or STOP/L but-

ton until your desired hour appears.

(Example: 5, PM)

converter box or satellite box, the local PBS station

must be selected on the cable box itself and the

TV/VCR must be set to the output channel of the

cable converter box or satellite box (usually chan-

nel 3 or 4), to be able to set up or correct the clock

automatically.

0 5

0 6 THU 2 0 0 4

HOUR

0 5

MINUTE

– – PM

Then press the F.FWD/B button.

– MANUAL CLOCK SET –

MONTH DAY YEAR

7 Select the minute

Press the PLAY/K or STOP/L but-

ton until the desired minute

appears. (Example: 40)

0 5

0 6 THU 2 0 0 4

HOUR

0 5

MINUTE

4 0 PM

- 11 -

9I03

1 Select “SETTING CLOCK”

Press the MENU button on the

remote control.

Press the PLAY/K or STOP/L but-

ton to select “SETTING CLOCK”.

Press the F.FWD/B button to enter

“SETTING CLOCK” menu.

5 Turn off the TV/VCR

Once the TV/VCR is turned off , it will periodically

check and set the correct date and time.

– M E N U –

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

DAYLIGHT-SAVING TIME

Select this feature and the TV/VCR’s clock automati-

cally will advance one hour in April, then reverse one

hour in October.

When Daylight-Saving Time is ON, the clock will

change automatically as follows:

– SETTING CLOCK –

2 Set “AUTO CLOCK” to [ON]

Press the F.FWD/B button until

“AUTO CLOCK [ON]” appears.

AUTO CLOCK

AUTO CLOCK CH SEARCH

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[ON]

[ 02 ]

[OFF]

First Sunday of April : At 2 AM the clock imme-

•

diately changes to 3 AM. Any timer programming

you have set to occur between 2 AM and 3 AM

will not record.

3 Begin “AUTO CLOCK CH SEARCH”

Last Sunday of October : At 2 AM the clock

immediately changes to 1 AM.

Make sure ...

Press the POWER button to turn on the TV/VCR.

•

Press the STOP/L button to select

– SETTING CLOCK –

“AUTO CLOCK CH SEARCH”.

AUTO CLOCK

AUTO CLOCK CH SEARCH

[ON]

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[ 02 ]

Press the F.FWD/B button.

•

[OFF]

The TV/VCR is now searching

•

for the station which contain the

auto clock set signal. The search

for a signal may take up to 20

seconds per channel.

1 Select “SETTING CLOCK”

Press the MENU button on the

– M E N U –

remote control.

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

“_ _” appears at the lower left of

the screen when the search has

ended.

– AUTO CLOCK CH SEARCH –

•

Press the PLAY/K or STOP/L but-

ton to point to “SETTING

CLOCK”.

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

Auto Clock station- write down

•

Then press the F.FWD/B button.

_ _

the number(s) that appear on the

screen. These are the auto clock

station(s) in your area. See item

4 below.

If no number(s) appear on the TV screen, there are

no stations in your area which contain the Auto

Clock signal. Auto Clock Setting is not possible.

Please use Manual Clock Setting on page 11.

2 Set “D.S.T.” (Daylight-Saving Time) to [ON]

Press the PLAY/K or STOP/L but-

ton to point to “D.S.T.”.

Then press the F.FWD/B or

– SETTING CLOCK –

AUTO CLOCK

[ON]

•

AUTO CLOCK CH SEARCH

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[ 02 ]

[ON]

REW/s button until [ON] appears.

Press the MENU button to exit the screen.

NOTE: During Auto Clock CH Search, the picture

may be distorted, this is normal.

3 Exit the Daylight-Saving Time mode

Press the MENU button on the remote control to

return to TV mode.

4 Enter the channel number that contains the

Automatic Clock Setting Signal

Press the MENU button on the remote control.

Press the PLAY/K or STOP/L but-

TO CANCEL THE DAYLIGHT-SAVING

TIME

Repeat steps [1] to [2], select [OFF] using the

– M E N U –

ton to select “SETTING CLOCK”.

Press the F.FWD/B button to

F.FWD/B or REW/s button.

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

enter “SETTING CLOCK” menu.

Press the STOP/L button to select

“AUTO CLOCK CH”.

Press the F.FWD/B or REW/s

buttons until you locate Auto

Clock Set station number. See

item 3 above.

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

– SETTING CLOCK –

AUTO CLOCK

AUTO CLOCK CH SEARCH

AUTO CLOCK CH

MANUAL CLOCK SET

D.S.T.

[ON]

[

45]

[OFF]

Press the MENU button to exit the

screen.

- 12 -

9I03

DELETING (OR ADDING)

CHANNEL(S)

The channels you no longer receive or seldom watch

can be deleted from the memory. (Of course, you

can add the deleted channel into the memory again.)

CHANNEL SET UP

You can program the tuner to scan all the channels

you receive in your area.

NOTE: Channel setup is NOT needed when connect-

ed to a cable box or satellite box. Just select the

TV/VCR channel selector to the output channel of

the cable box or satellite box (Ex CH3), then select

the channel to be viewed on the Cable Box or

Satellite Box.

1 Select “CHANNEL SET UP”

Press the MENU button on the

remote control.

Press the PLAY/K or STOP/L but-

ton to point to “CHANNEL SET

UP”.

– M E N U –

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

Make sure ...

Press the POWER button to turn on the TV/VCR.

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

•

TIME SEARCH

Then press the F.FWD/B button.

1 Select “CHANNEL SET UP”

Press the MENU button on the

remote control.

– M E N U –

2 Select “ADD/DELETE CH”

Press the PLAY/K or STOP/L but-

ton to point to “ADD/DELETE

CH”.

– CHANNEL SET UP –

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ADD / DELETE CH (CATV)

AUTO CH PROGRAMMING

Press the PLAY/K or STOP/L but-

ton to point to “CHANNEL SET

UP”.

ZERO RETURN

TIME SEARCH

Press the F.FWD/B button.

Then press the F.FWD/B button.

3 Enter the desired channel number

Press the PLAY/K or STOP/L but-

ton until your desired channel num-

ber appears. (You can also use the

number buttons or the CHANNEL

K/L button to enter it) (Example:

CH8)

2 Begin auto preset

– CHANNEL SET UP –

Press the PLAY/K or STOP/L but-

ton to point to “AUTO CH PRO-

GRAMMING”.

ADD / DELETE CH (CATV)

AUTO CH PROGRAMMING

ADD / DELETE

Then press the F.FWD/B button.

The tuner scans and memorizes all

the active channels in your area.

You must precede single-digit channel numbers

with a zero (Example: 02 ... 09).

•

When selecting cable channels which are higher

than 99, press the +100 button first, then press the

last two digits. (Example: to select channel 125,

first press the +100 button then press “2” and “5”).

•

3 After scanning

The tuner stops on the lowest memorized channel.

•

When AUTO CH PROGRAMMING is activated

where there is no TV signal input, “NO TV SIG-

NALS” will appear on the display after the com-

pletion of the channel scanning.

4 Delete (or add) it from (into) memory

Press the F.FWD/B or REW/s button. The channel

number changes to light red. The channel is deleted

from memory.

To delete another channel, repeat steps [3] and [4].

If you press the F.FWD/B or REW/s button

The TV/VCR may recognize TV channels to be

•

CATV channels by the receiving conditions. In this

case, try auto preset again in the fine receiving

conditions.

•

again, the channel is memorized again.

Added channel: Light blue.

Deleted channel: Light red.

5 Exit the channel setup mode

Press the MENU button on the remote control to

return to TV mode.

NOTE: To confirm that channel(s) has been deleted

or added, press the CHANNEL K or L button.

- 13 -

9I03

TV OPERATION

WATCHING A TV PROGRAM

PICTURE CONTROL

The TV/VCR’s picture controls – BRIGHT, CON-

TRAST, COLOR, TINT and SHARPNESS – are

preset to factory specifications. Although they are

usually the best, you may need to make some further

adjustments for a more natural looking image.

NOTES:

1 Turn on the TV/VCR

Press the POWER button to turn on the TV/VCR.

2 Select the channel number

Press the CHANNEL K or L button to select your

desired channel number or press the number buttons

on the remote control.

Remember: If the TV/VCR is connected to a cable

box or satellite box, the TV/VCR must be on CH3 or

CH4, then the channel to be viewed must be selected

on the cable box or satellite box.

Procedures must be followed within 5 seconds or

the Picture Control mode will be cancelled.

•

When setting the Picture Control, the Game mode

will be cancelled.

•

Make sure ...

TV/VCR power must be turned on.

•

1 Select “PICTURE CONTROL”

3 Adjust sound

Press the VOLUME X or Y button

to adjust the volume.

Press the MENU button on the

– M E N U –

remote control.

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

Press the PLAY/K or STOP/L but-

ton to point to “PICTURE CON-

TROL”.

VOLUME 20

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

Then, press the F.FWD/B button.

GAME MODE

2 Select item you want to adjust

Press the PLAY/K or STOP/L button until desired

This function enables you to decrease the TV screen

contrast and making it suitable for use with a TV

GAME.

control is displayed.

BRIGHT

CONTRAST

NOTE: This function can not be set during recording.

BRIGHT

COLOR

–

P +

TINT

Press the GAME button on the

GAME

remote control. “GAME” appears

on the screen.

SHARPNESS

3 Adjust the picture control

When you press the GAME button;

Press the F.FWD/B or REW/s button to adjust to

The TV/VCR comes on automatically if it is off.

The TV/VCR will be in external input mode auto-

•

your desired level.

matically.

TO CANCEL THE GAME MODE

Press the GAME button or CHANNEL K or L but-

ton on the remote control.

REW/s

to decrease

brightness

to decrease

contrast

F.FWD/B

to increase

brightness

to increase

contrast

BRIGHT

CONTRAST

DEGAUSSING

Magnetism from nearby appliances might affect the

color of the TV picture.

If this happens, move this unit away from the appli-

ance. If the color is still not correct, disconnect

power cord from AC outlet then reconnect it after 30

minutes.

COLOR

TINT

to pale

to brilliant

to purple

SHARPNESS to soft

to green

to clear

If there is a power failure of any kind, the unit will

retain its memory for this feature.

•

- 14 -

9I03

TO CANCEL THE CLOSED CAPTION

SYSTEM

CLOSED CAPTION SYSTEM

You can view specially labeled (cc) TV programs,

movies, news and pre-recorded tapes with either a

dialogue caption or text display.

Repeat steps [1] and [2], select [OFF] using the

F.FWD/B or REW/s button. Press the MENU but-

ton on the remote control to return to TV mode.

CAPTION mode: By choosing the caption mode, you

can watch dramas, movies and news while captioning

the dialogues and the contents of news.

TEXT mode: By choosing the text mode, you can

watch half screen text information if you want.

1-2: You may get these captions or text information

by selecting either “1” or “2”. Caption “2” is used,

usually for a second language if available.

WHEN THE CLOSED CAPTION MODE

IS ON

The On-Screen Display will disappear after 5 sec-

onds.

This is also true when the MUTE button is pressed

or when the PAUSE/STILL button is pressed while

recording.

•

If there is a power failure of any kind, the unit will

retain its memory for this feature.

•

NOTE:

Not all programs are broadcast with closed captions.

Your television is designed to provide error free

closed captions from high quality antenna, cable and

VCR signals. Conversely, poor quality signals are

likely to result in caption errors or no captions at all.

Common signal conditions which may cause captions

errors are listed below:

V-CHIP SET UP

V-CHIP enables parents to prevent their children

from watching inappropriate material on TV.

V-CHIP reads the ratings for programming (except

for news and sports programs, unedited movies on

premium cable channels and Emergency Broadcast

System signals), then denies access to programming

if the program’s rating meets the limitations you

select. In this case, “PROTECTED PROGRAM by

...” message appears on the TV screen.

To block ratings, follow the steps below.

Programming may be rated by the Motion Picture

Association of America (MPAA) or according to

the Television Parental Guidelines. In order to

block any inappropriate programming, set your

limits in both places (MPAA RATING and TV

RATING).

Automobile ignition noise

Electric motor brush noise

Weak snowy reception on TV screen

Multiplex signal reception displaying picture

•

ghosts or airplane flutter.

Playback of poorly recorded or worn VCR tapes.

NOTE:

•

If the TV/VCR displays a black box on the TV

screen, this means that the TV/VCR

is set to the TEXT mode. To clear

screen, select [CAPTION1], [CAP-

TION2] or [OFF].

Make sure ...

TV/VCR power must be turned on.

•

TV RATING SET UP

Make sure ...

– M E N U –

1 Select “CAPTION”

TIMER PROGRAMMING

TV/VCR power must be turned on.

•

PICTURE CONTROL

Press the MENU button on the

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

remote control.

Press the PLAY/K or STOP/L but-

ton to point to “CAPTION”.

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

1 Select “V-CHIP SET UP”

– M E N U –

TIMER PROGRAMMING

Press the MENU button on the

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

remote control.

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

Press the PLAY/K or STOP/L but-

ton to point to “V-CHIP SET UP”.

Then press the F.FWD/B button.

2 Select your desired caption menu

Press the F.FWD/B or REW/s

button until your desired caption

menu appears.

([CAPTION1], [CAPTION2],

[TEXT1] or [TEXT2])

TIME SEARCH

– M E N U –

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [CAPTION1]

ZERO RETURN

2 Select “TV RATING”

Press the PLAY/K or STOP/L but-

ton to point to “TV RATING”.

Then press the F.FWD/B button.

– V-CHIP SET UP –

TIME SEARCH

TV RATING

MPAA RATING

3 Exit the caption setting mode

Press the MENU button on the remote control to

return to TV mode.

- 15 -

9I03

3 Select your desired item

Press the PLAY/K or STOP/L button to point to

your desired item.

4 Exit the V-Chip setting mode

Press the MENU button on the remote control to

return to original mode.

Then, press the F.FWD/B button to

select [BLOCK] or [VIEW].

TV–Y

TV–Y7

TV–G

TV–PG (

TV–14

TV–MA(

[VIEW]

MPAA RATING SET UP

(

)

(

Make sure ...

When you select the rating cate-

gory and change it to [BLOCK],

the higher rating will change to

•

TV/VCR power must be turned on.

•

[BLOCK] automatically. Also, the lower rating will

change to [VIEW] automatically.

When you change “TV-Y” to [VIEW], the all rat-

ings will change to [VIEW] automatically.

1 Select “V-CHIP SET UP”

– M E N U –

Press the MENU button on the

TIMER PROGRAMMING

•

PICTURE CONTROL

remote control.

Press the PLAY/K or STOP/L but-

ton to point to “V-CHIP SET UP”.

Then press the F.FWD/B button.

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

Selection

TV-Y

Rating Category Explanations

Appropriate for all children

TIME SEARCH

TV-Y7

TV-G

TV-PG

TV-14

Appropriate for children seven and older

General Audience

Parental Guidance suggested.

Unsuitable for children under 14

– V-CHIP SET UP –

2 Select “MPAA RATING”

Press the PLAY/K or STOP/L but-

ton to point to “MPAA RATING”.

Then press the F.FWD/B button.

TV RATING

MPAA RATING

TV-MA Mature audience only

When you select TV-Y7, TV-PG, TV-14 or TV-MA

and you press the F.FWD/B button, the sub-ratings

will appear on the TV screen.

If you select the rating category (example: TV-PG)

and change it to [BLOCK] or [VIEW], the sub-rat-

ings (example: V for Violence) will change to

[BLOCK] or [VIEW] automatically.

3 Select your desired item

Press the PLAY/K or STOP/L but-

ton to point to your desired item.

Then press the F.FWD/B button to

select [BLOCK] or [VIEW].

[VIEW]

PG–13

NC–17

[VIEW]

[BLOCK]

You can set the sub-ratings to [BLOCK] or [VIEW]

individually when the rating category is set to

[BLOCK].

To set the sub-ratings individually, follow the steps

below.

Selection

PG-13

Rating Category Explanations

General Audience

Parental Guidance suggested.

Unsuitable for children under 13

Restricted; under 17 requires accompa-

nying parent or adult guardian

No one under 17 admitted

When you select [TV-Y7]:

•

TV–Y7

[BLOCK]

Press the STOP/L or PLAY/K

button to select “FV” (Fantasy

Violence).

NC-17

Mature audience only

Then press the F.FWD/B button

to select [BLOCK] or [VIEW].

When you select the rating category and change it

to [BLOCK], the higher rating will change to

[BLOCK] automatically. Also, the lower rating

will change to [VIEW] automatically.

When you change “G” to [VIEW], all ratings will

change to [VIEW] automatically.

•

When you select [TV-PG], [TV-14] or [TV-MA]:

Press the STOP/L or PLAY/K

•

button to select “D”(Suggestive

Dialog), “L”(Coarse Language),

“S”(Sexual Situation) or

TV–PG

[BLOCK]

“V”(Violence). Then press the

F.FWD/B button to select

[BLOCK] or [VIEW].

Note: When you select [TV-MA], “D” does not

appear on the TV screen.

4 Exit the V-Chip setting mode

Press the MENU button on the remote control to

return to original mode.

The sub-ratings which set to

TV–Y

TV–Y7

TV–G

TV–PG (DLSV)

TV–14 (DLSV)

TV–MA ( LSV)

[VIEW]

(

)

[VIEW]

[BLOCK] appears next to the rat-

ing category in the TV RATING

menu.

[BLOCK]

- 16 -

9I03

PLAYBACK

This TV/VCR will operate with any cassette that has the

mark. For best results, we

recommend the use of high-quality tapes. Do not use poor quality or damaged tapes.

INSERTING A CASSETTE

Insert the cassette in the direction as shown. Push in

gently, but continuously, on the center-back of the

cassette until it is drawn into the TV/VCR. The

TV/VCR will automatically turn on.

AUTO REPEAT PLAYBACK

The TV/VCR has the auto repeat function that allows

you to repeat a tape indefinitely without touching the

PLAY button.

ALL REPEAT: Repeat playback from the beginning

to the end of the tape.

BLANK REPEAT: Repeat playback from the begin-

ning to a blank part, which is blank for more than

10 seconds.

Window

WRONG

CORRECT

1 Select “USER’S SET UP”

PRECAUTIONS

– M E N U –

Press the MENU button on the

TIMER PROGRAMMING

PICTURE CONTROL

Avoid moisture. Moisture condensation may occur

on the tape if it is moved from a cold place to a

warm place or visa versa. Before using a tape with

these conditions, to avoid damage of the tape and

your TV/VCR, wait until the tape has warmed to

room temperature and the moisture has evaporated.

Avoid extreme heat, high humidity and magnetic

fields.

•

remote control.

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

Press the PLAY/K or STOP/L but-

ton to point to “USER’S SET UP”.

Then press the F.FWD/B button.

•

2 Select “ALL” or “BLANK”

Press the PLAY/K or STOP/L button to point to

“REPEAT PLAY”.

Press the F.FWD/B or REW/s

button repeatedly until your desired

selection [ALL] or [BLANK]

appears.

Do not tamper with the cassette mechanism.

Do not touch the tape with your fingers.

•

USER’S SET UP

–

RENTAL

REPEAT PLAY

AUTO RETURN

[OFF]

[ALL]

[OFF]

NORMAL PLAYBACK

Make sure ...

TV/VCR power must be turned on.

•

3 Exit the Repeat Play setting

Press the MENU button on the remote control to

return to the TV mode.

1 Insert a prerecorded tape

If the erase-protection tab has been removed, the

TV/VCR will start playback automatically.

4 Start playback

Press the PLAY button to start the Repeat Play.

“REPEAT PLAY B” appears.

PLAY

2 To begin playback

Press the PLAY button.

Once you select the Repeat Play mode, it stays in

effect even after you turn off the TV/VCR.

If the Rental mode is set [ON], the “RENTAL

PLAY B” display has priority.

Note: If any menu is activated on

the screen, the PLAY button does

not function. Press the MENU but-

ton to clear the menu. then, press

the PLAY button.

•

STOP

3 To stop playback

Press the STOP button when play-

back is completed.

TO CANCEL THE REPEAT PLAY MODE

Repeat steps [1] and [2], select [OFF] using the

F.FWD/B or REW/s button on the remote control.

Press the MENU button on the remote control to

return to TV mode.

If there is a power failure of any kind, the unit

will retain its memory for this feature.

- 17 -

9I03

NOTES:

Time Search can be set up to a maximum of 9

•

hours 50 minutes (9:50) by 10 minutes at a time.

PICTURE SEARCH

This feature is very useful in finding or skipping over

a particular scene on a tape. In this mode, the sound

will be muted.

This function will not operate in recording mode.

•

In the example below: To watch a program after 2

hour 50 minutes from the present position, in either

direction.

1) You may view a video tape at a high speed in

either a forward or reverse direction by pressing

the F.FWD/B or REW/s button during playback.

(in the SP / LP / SLP modes)

2) Press it again and the TV/VCR will now search in

super high speed. (in the LP / SLP modes only)

NOTE: Tapes recorded in the SP or LP mode will

display a noise bar on the TV screen and the picture

may revert to Black and White. This is normal.

3) Press the PLAY/K button to return to normal

speed.

1 Insert a tape.

2 Select “TIME SEARCH” mode

Press the TIME SEARCH button (with each push it

will increase by 10 minute).

3 Enter your desired time

Press the PLAY/K or STOP/L but-

ton until your desired time appears.

(Example: “2:50” stands for 2 hours

50 minutes)

If you wish to cancel the Time Search at this point,

press the MENU button on the remote control.

TIME SEARCH

2 : 50

ZERO RETURN

This function allows you to search easily a beginning

point that you want to review by rewinding or fast

forwarding.

NOTE:

4 Begin Time Search

Zero Return WILL NOT work on a blank tape or a

blank portion of a tape.

By pressing the REW/s or F.FWD/B button, the

TV/VCR will rewind or fast forward to the specified

point.

1 Stop a tape at your desired point

Rewind or fast forward the tape to the beginning

point at which you want to review.

The time counts down as the searching progresses.

When 0:00 is reached, the tape will start playback

automatically.

2 Reset the counter to 0:00:00

Press the COUNTER RESET button repeatedly.

TO CANCEL THE TIME SEARCH at this

point

Press the STOP/EJECT button on the TV/VCR or the

remote control. This will delete the selected time.

3 Begin recording or playback

Press the RECORD or PLAY button.

Press the STOP button when recording or playback is

completed.

STILL PICTURE

You can view a still picture on the TV screen during

playback (the Still mode). Press the PAUSE/STILL

button during playback. Only tapes recorded in the

SLP mode will show the least amount of lines. Press

the PLAY button to return to playback.

NOTES:

4 To activate “ZERO RETURN” mode

Press the MENU button on the remote control.

Press the PLAY/K or STOP/L button to point to

“ZERO RETURN”.

– M E N U –

TIMER PROGRAMMING

Then press the F.FWD/B button.

PICTURE CONTROL

Usually there will be video “noise” lines (black

and white streaks or dots) on the screen. This is

normal.

SETTING CLOCK

•

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

The counter will appear on the TV

screen.

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

The tape will automatically stop

when the counter returns to 0:00:00.

TIME SEARCH

If the tape was originally recorded in SP or LP

mode, the still picture will be black and white in

addition to the “noise” lines.

This is not a fault of the machine, but is a by-

product of the technology involved in producing

a TV/VCR with 2 video heads.

TIME SEARCH

The Time Search function makes it possible to

quickly advance the tape to your desired position

simply by entering the exact amount of playback

time you want to skip.

If it is left in the Pause mode for more than five

minutes, the TV/VCR will automatically switch to

the Stop mode.

•

- 18 -

9I03

NOISE CANCEL (in the Still mode)

RENTAL PLAYBACK

This feature allows you to reposition or reduce the

noise lines of a still picture. Press the PAUSE/STILL

button so that the noise lines change position on the

screen so you can see the picture in its entirety with-

out distracting noise lines.

NOTE: This feature can be activated ONLY when

viewing a tape recorded in the SLP mode. If the tape

was originally recorded in the SP or LP mode, the

still picture may revert to black and white in addition

to the “noise bars”. This is normal.

This function enables you to improve the picture

quality when playing back worn cassettes such as

rented tapes.

1 Select “USER’S SET UP”

– M E N U –

TIMER PROGRAMMING

Press the MENU button on the

PICTURE CONTROL

SETTING CLOCK

remote control.

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

Press the PLAY/K or STOP/L but-

ton to point to “USER’S SET UP”.

Then press the F.FWD/B button.

VERTICAL HOLD CONTROL

If the picture begins to vibrate vertically while in

Pause/Still mode, stabilize the picture by pressing the

CHANNEL K or L button.

USER’S SET UP

–

2 Set “RENTAL” to [ON]

Press the PLAY/K or STOP/L but-

ton to point to “RENTAL”.

Press the F.FWD/B or REW/s

button until [ON] appears.

RENTAL

REPEAT PLAY

AUTO RETURN

[ON]

[OFF]

NOTE:

If there are video noise lines on the screen, reposition

or reduce them. Refer to “NOISE CANCEL”.

3 Exit the Rental setting

Press the MENU button on the remote control to

return to the TV mode.

PICTURE CONTROLS

TRACKING ADJUSTMENT

4 Start playback

Tracking adjustment will be set automatically

(Digital Tracking function) when you start play-

back.

•

Press the PLAY button to start playback. “RENTAL

PLAY B” appears.

Once you select the Rental mode, it stays in effect

even after you turn off the TV/VCR.

•

However when playing pre-recorded tapes or tapes

•

recorded on units other than your own, noise lines

(black and white streaks) may appear on the play-

back picture. If this occurs, you can adjust the

tracking control manually by pressing the CHAN-

NEL K or L button until the streaks disappear. To

return to the DTR function, stop the tape once and

start playback again.

TO CANCEL THE RENTAL MODE

Repeat steps [1] and [2], select [OFF] using the

F.FWD/B or REW/s button on the remote control.

Press the MENU button on the remote control to

return to TV mode.

If there is a power failure of any kind, the unit

will retain its memory for this feature.

RECORDING

TWO DIFFERENT TAPE SPEEDS

ERASE PREVENTION

Before recording, select the tape speed from : SP

mode (Standard Play) or SLP mode (Super Long

Play).

The table below shows the maximum recording/play-

back time using T60, T120 or T160 tapes in each

mode.

You can prevent accidental

erasing of recording by

breaking off the tab on the

back edge of the cassette.

Tab

Tape Speed

Type of tape

SP mode

Recording/Playback Time

If you decide to record on

the tape again, cover the

hole with plastic tape.

T60

1 hour

3 hours

T120

T160

2 hours 2-2/3 hours

6 hours 8 hours

SLP mode

Note: You can playback a tape recorded in LP mode

(Long Play).

Plastic Tape

- 19 -

9I03

Make sure ...

TV/VCR power must be turned on.

Insert a cassette tape with its erase prevention tab in place. (If necessary, rewind or fast forward the tape to

the point at which you want to begin recording.)

•

NOTE: This unit will ONLY record and view the same channel.

NORMAL RECORDING

OTR (One Touch Recording)

You can ONLY watch the same TV program that is

being recorded.

This function enables you to set a recording length

simply by pressing the REC/OTR button on the

TV/VCR.

Make sure ...

1 Select the channel to be recorded

TV/VCR power must be turned on.

Insert a cassette tape with its erase prevention tab

Press the number buttons on the

•

CH 10

remote control or the CHANNEL

K or L button.

in place. (If necessary, rewind or fast forward the

Remember: If the TV/VCR is con-

nected to a cable box or satellite

box, the TV/VCR must be on CH3

or CH4, then the channel to be recorded must be

selected on the cable box or satellite box.

tape to the point at which you want to begin

recording.)

NOTES:

You cannot start OTR with the remote control.

Recording starts immediately when the REC/OTR

button is pressed.

•

2 Select the tape speed

Press the SPEED button to select

the desired tape speed (SP/ SLP).

When the REC/OTR button is pressed 18 times, the

TV/VCR returns to the Normal Recording mode.

To stop the OTR operation, press the STOP button

on the TV/VCR or on the remote control.

•

To show the remaining time, press the DISPLAY

•

button on the remote control so that “OTR”

appears on the TV screen. (It will show up momen-

tarily then disappear.)

REC

3 Begin recording

Press the RECORD button.

Recording stops when 0:00 is reached.

Please note that in the SLP mode maximum record-

ing time, assuming the tape is started at the begin-

ning, is 8 hours using T-160 (or 6 hours using T-120).

•

If the tape runs out before the end time, the

TV/VCR will switch to the Stop mode immediate-

ly, ejects the tape and turns itself off.

•

4 Stop recording

Press the STOP button when recording is completed.

If you press the power button during OTR, the

TV/VCR continues recording until the selected

length is reached.

•

SKIPPING UNWANTED

SCENES DURING RECORDING

Press the PAUSE/STILL button to

temporarily stop recording.

Press the PAUSE/STILL or

RECORD button to resume record-

ing.

PAUSE

1 Select the channel to be recorded

Press the number buttons on the remote control or the

CHANNEL K or L button.

Remember: If the TV/VCR is connected to a cable

box or satellite box, the TV/VCR must be on CH3 or

CH4, then the channel to be recorded is selected on

the cable box or satellite box.

NOTES:

After five minutes, the TV/VCR will automatically

switch to the Recording mode to prevent tape dam-

age.

•

2 Select the tape speed

Press the SPEED button to select the desired tape

speed (SP/ SLP).

If “CLOSED CAPTION (ON)” is selected, the On-

Screen Display will appear for 5 seconds, then dis-

appear.

•

- 20 -

9I03

Avoid overlap of programs ...

There is a chance that a program will not be recorded

when programs overlap;

3 Begin OTR

OTR(2 : 30)

Press the REC/OTR button on the

TV/VCR as many times as needed.

The recording length will be deter-

mined by the number of times you

press the REC/OTR button. Each

The program with an earlier start has priority.

Once the earliest program finishes, the overlapping

programs will begin recording in sequence.

•

The illustration below demonstrates the sequence

of recordings.

•

additional push will increase the recording time by

30 minutes. It is set up to 8 hours.

Recording Sequence

Program 1

10:00AM-11:00AM

Program 2

9:00AM-10:00AM

Program 3

Push(es) Display

1 push

Recording length

(normal recording)

2 pushes

3 pushes

0:30

1:00

30 minutes

60 minutes

9:30AM-12:00PM

9:00AM

10:00AM

11:00AM

12:00PM

*Recording period is SHADED

17 pushes

8:00

480 minutes

1 Select “TIMER PROGRAMMING”

Press the MENU button on the

remote control.

Confirm “TIMER PROGRAM-

MING” is pointed by pressing the

PLAY/K button, then press the

F.FWD/B button.

– M E N U –

TIMER RECORDING

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

You may set the TV/VCR to start and end a record-

ing while you are away. You can set 8 programs to

record on specific days, daily or weekly within a 1

year period.

In the example below, the timer is being set to record:

July 4th, 2004

SETTING TIME: from 7:30PM to 8:50PM

ZERO RETURN

TIME SEARCH

If you have not yet set the clock, “MANUAL

CLOCK SET” appears. If so, follow steps [3] to

[8] on page 11. Then set the timer recording.

•

DATE:

CHANNEL:

TAPE SPEED:

CH61

2 Select your desired program position (1~8)

– TIMER PROGRAMMING –

Press the PLAY/K or STOP/L but-

ton to select the desired program

position.

CH DATE

BEGIN END

Make sure ...

- - -/- - - - - -:- -

-:- - - -

If a cable box or satellite box is connected with the

TV/VCR you will be limited to record only one

channel, and the channel selector on the TV/VCR

must be selected to the output channel of the boxes

CH 3 or CH 4 and then the actual channel to be

recorded must be selected on the boxes.

Clock must be set to the correct time and date

before setting the timer.

TV/VCR power must be turn on to program it.

Insert a cassette tape with its erase prevention tab

in place. (If necessary, rewind or fast forward the

tape to the point at which you want to begin

recording.)

•

Then press the F.FWD/B button.

3 Set the channel number

Press the PLAY/K or STOP/L but-

ton until the desired channel num-

ber appears.

– TIMER PROGRAMMING –

CH DATE BEGIN END

•

- - -/- - - - - -:- -

61 -/- - - - - -:- -

- - -/- - - - - -:- -

-:- - - -

•

(Example: CH61)

Then press the F.FWD/B button.

Remember: If the TV/VCR is connected to a cable

box or satellite box, the TV/VCR must be on CH3 or

CH4, then the channel to be recorded is selected on

the cable box or satellite box.

The channel you want to record is properly set in

advance.

•

4 Select once, every day or weekly recording

For once recording :

– TIMER PROGRAMMING –

CH DATE

BEGIN END

Press the PLAY/K (up) button

until the desired date appears.

(Example: “7/04” for July 4th).

Then press the F.FWD/B button.

- - -/- - - - - -:- -

61 7/04 SUN -:- -

- - -/- - - - - -:- -

-:- - - -

- 21 -

9I03

For every day recording : To record a TV program at

the same time on the same channel every day.

(Example: Monday through Sunday)

10 Finish setting the program

Press the F.FWD/B or REW/s button. The program

is now completed.

– TIMER PROGRAMMING –

Press the STOP/L (down) button

CH DATE

BEGIN END

To set another program, repeat steps [2] to [10].

Press the MENU button on the remote control to

•

until “EVRY DAY” appears.

Then press the F.FWD/B button.

- - -/- - - - - -:- -

61 EVRY DAY -:- -

- - -/- - - - - -:- -

-:- - - -

return to original mode.

11 Set the timer

For weekly recording : To record a TV program at

Press the POWER button to set automatic timer

recording. The RECORD indicator lights up.

the same time on the same channel every week.

(Example: every Monday)

– TIMER PROGRAMMING –

CH DATE

BEGIN END

You must turn off the TV/VCR to activate automat-

ic timer recording.

•

Press the STOP/L (down) button

until “EVRY” and your desired

day of the week appear together.

Then press the F.FWD/B button.

- - -/- - - - - -:- -

61 EVRY MON -:- -

- - -/- - - - - -:- -

-:- - - -

If power is not turned off and you continue watch-

ing TV, “TIMER REC STANDBY” starts flashing

on the TV screen 2 minutes before the programmed

start time.

– TIMER PROGRAMMING –

CH DATE BEGIN END

5 Set beginning hour

Press the PLAY/K or STOP/L but-

ton until the desired hour appears.

(Example: “7, PM” for 7:30PM)

Then press the F.FWD/B button.

- - -/- - - - - -:- -

-:- - - -

TIMER PROGRAM EXTENSION

61 7/04 SUN 7:12^P

- - -/- - - - - -:- -

To shift the time schedule of an automatic timer

recording.

1) Press the POWER button.

2) Repeat step [1] on page 21.

3) Press the RECORD button and select the desired

program using the PLAY/K or STOP/L button.

4) Press the RECORD button again.

6 Set beginning minute

– TIMER PROGRAMMING –

CH DATE BEGIN END

Press the PLAY/K or STOP/L but-

ton until the desired minute appears.

(Example: “30” for 7:30PM)

- - -/- - - - - -:- -

-:- - - -

61 7/04 SUN 7:30^P

- - -/- - - - - -:- -

Then press the F.FWD/B button.

Each additional push will shift forward the

begin/end time for recording by 10 minutes. When

the recording is already in progress, each addition-

al push will shift forward the end time only. If you

want to cancel while setting, press the

– TIMER PROGRAMMING –

CH DATE BEGIN END

7 Set end hour

Press the PLAY/K or STOP/L but-

ton until the desired hour appears.

(Example: “8, PM” for 8:50PM)

Then press the F.FWD/B button.

- - -/- - - - - -:- -

-:- - - -

61 7/04 SUN 7:30^P

- - -/- - - - - -:- -

8:30^P

-:- - - -

-:- - - - -

PAUSE/STILL button on the remote control. The

recording time returns to the original time.

NOTE: When you shift forward the time schedule

during recording, the recording speed will automati-

cally be set to the SLP mode.

5) Press the F.FWD/B or REW/s button to exit the

setting menu. Then press the MENU button on the

remote control to return to original mode.

– TIMER PROGRAMMING –

CH DATE BEGIN END

8 Set end minute

Press the PLAY/K or STOP/L but-

ton until the desired minute appears.

(Example: “50” for 8:50PM)

Then press the F.FWD/B button.

- - -/- - - - - -:- -

-:- - - -

61 7/04 SUN 7:30^P

- - -/- - - - - -:- -

8:50^P

-:- - - -

TO CORRECT A PROGRAM

– TIMER PROGRAMMING –

CH DATE BEGIN END

9 Set the tape speed

Press the PLAY/K or STOP/L but-

ton until the desired tape speed

appears. (Example: SP)

While setting a program; press the REW/s but-

ton to go back one step and enter the correct num-

•

- - -/- - - - - -:- -

-:- - - -

8:50^PMSP

-:- - - -

bers using the PLAY/K or STOP/L button.

61 7/04 SUN 7:30^P

- - -/- - - - - -:- -

After setting a program;

1) Press the POWER button.

•

2) Repeat steps [1] - [2] on page 21.

3) Press the F.FWD/B button (or press the

REW/s button to go back one step) until the

part you want to correct begins flashing, then

make the changes pressing the PLAY/K or

STOP/L button.

4) Press the POWER button to set automatic timer

recording.

- 22 -

9I03

TO CANCEL AN AUTOMATIC TIMER

RECORDING

USER’S SET UP

–

2 Set “AUTO RETURN” to [ON]

Press the PLAY/K or STOP/L but-

ton to point to “AUTO RETURN”.

Press the F.FWD/B or REW/s

button until [ON] appears.

RENTAL

REPEAT PLAY

AUTO RETURN

[OFF]

[ON]

After setting a program;

1) Press the POWER button.

•

2) Repeat steps [1] - [2] on page 21 and select a

program you want to cancel.

3) Press the T-PROG. CLEAR button.

4) Press the MENU button on the remote control

to return to TV mode.

3 Auto Return will begin

When all the timer recordings are completed, the

TV/VCR will rewind to the beginning of the recorded

While recording is in progress;

1) Press POWER button.

program(s).

NOTE:

•

2) Press the STOP/EJECT button on the TV/VCR.

If you press the POWER button while tape is

rewinding, the Auto Return will stop.

•

TO CHECK THE BEGIN/END TIME

4 Watch the recorded program

Press the PLAY/K button.

1) Press the POWER button so that the Recording

indicator goes off.

2) Press the MENU button on the remote control.

3) Confirm “TIMER PROGRAMMING” is pointed.

4) Press the F.FWD/B button. The details of pro-

grams appear on the TV screen.

5) Press the MENU button on the remote control to

return to TV mode.

TO CANCEL THE AUTO RETURN

MODE

Repeat steps [1] and [2], select [OFF] using the

F.FWD/B or REW/s button.

If there is a power failure of any kind, the unit

will retain its memory for this feature.

HINTS FOR AUTOMATIC

TIMER RECORDING

WAKE UP TIMER

The Wake Up Timer function turns on the TV/VCR

without using the POWER button after a desired

period of time.

Make sure the channel you want to record is prop-

erly set in advance.

It is not necessary to press the RECORD button for

timer recording.

Recording begins automatically at the Start time.

If you are recording using a Timer mode, you may

not operate the unit manually.

The erase-prevention tab on the cassette must be in

place (or you must put tape over the hole).

If the erase-prevention tab is removed, the cassette

will be ejected when the POWER button is pressed

to off.

•

NOTES:

Use the remote control for this procedure.

Clock must be set to the correct time before setting

•

the timer.

If you want to select [TAPE], you must insert a

cassette tape in the TV/VCR. The tape will start

playback automatically on your desired time.

•

If the tape runs out before the end time, the

TV/VCR will switch to the Stop mode immediately

and the tape will be ejected.

•

1 Select “WAKE-UP TIMER”

Press the WAKE UP/SLEEP button

on the remote control once, and

confirm “ON/OFF” is pointed.

AUTO RETURN

WAKE UP B ON/OFF

[ON]

TIMER

TV/TAPE

TIME

[TV]

Press the F.FWD/B or REW/s

[12:00AM]

button until [ON] appears.

With this feature, after timer recording is finished,

the beginning of the recorded program(s) can be

searched for automatically.

2 Select “TV” or “TAPE”

Press the PLAY/K or STOP/L but-

ton until to point to “TV/TAPE”.

Press the F.FWD/B or REW/s

button and select [TV] or [TAPE].

– M E N U –

1 Select “USER’S SET UP”

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

ZERO RETURN

TIME SEARCH

Press the MENU button on the

WAKE UP

TIMER

ON/OFF

B TV/TAPE

TIME

[ON]

remote control.

[TV]

[12:00AM]

Press the PLAY/K or STOP/L but-

ton to point to “USER’S SET UP”.

Then press the F.FWD/B button.

- 23 -

9I03

3 Set wake up time

1 Select “SLEEP TIMER”

Press the PLAY/K or STOP/L but-

ton until to point to “TIME”.

Press the F.FWD/B or REW/s

button until your desired wake up

time appears.

Press the WAKE UP/SLEEP button on the remote

control until “SLEEP TIMER” appears.

WAKE UP

TIMER

ON/OFF

[ON]

2 Set sleep time

Press the PLAY/K, STOP/L,

F.FWD/B or REW/s button until

your desired sleep time appears.

TV/TAPE

[TV]

B TIME

[12:00AM]

Each additional push will increase (or decrease) the

time by 10 minutes.

SLEEP TIMER [2:00]

Each additional push will increase

4 Exit the Wake Up Timer setting

Press the MENU button on the remote control to

return to TV mode.

the time by 30 minutes up to 120 minutes.

Press the MENU button on the remote control to exit

the Sleep Timer setting.

TO CANCEL THE WAKE UP TIMER

TO CANCEL THE SLEEP TIMER

Repeat step [1] but select [OFF].

Press the WAKE UP/SLEEP button on the remote

control until “SLEEP TIMER” appears.

To view the time left for sleep timer press the WAKE

UP/SLEEP button twice, then press the MENU but-

ton on the remote control to exit the sleep timer set-

ting.

SLEEP TIMER

The Sleep Timer function turns off the TV/VCR

without using the POWER button after a desired

period of time.

NOTE:

This function does not operate during Recording

mode.

•

COPYING A VIDEO TAPE

You can make copies of video tapes made by friends

or relatives for your enjoyment.

1) Insert a pre-recorded video cassette into the

source (Playing) VCR or camcorder.

2) Insert a blank video cassette or one you want to

record over, into the TV/VCR’s cassette compart-

ment.

3) Press the SPEED button on remote control for the

TV/VCR to select the desired recording speed

(SP/SLP).

WARNING: Unauthorized recordings of

copyrighted video tapes may be an

infringement of copyright laws.

Connect your TV/VCR and a Source (Playing) VCR

using the following diagram.

4) Press the CHANNEL K or L button on the

TV/VCR until “AUX” appears on the screen.

NOTE: “AUX” is found below the lowest memo-

rized channel. (Example: CH2)

VIDEO

AUDIO

[The TV/VCR]

5) Press the REC/OTR button on the TV/VCR.

6) Begin playback of the tape in the source (Playing)

VCR or camcorder.

NOTE: For best results during dubbing, use the

TV/VCR’s front panel controls whenever possible.

The remote control might affect the source (Playing)

VCR’s playback operation.

[Ex: Source (playing)

VCR or camcorder]

7) To stop copying, press the STOP/EJECT button

on the TV/VCR, then stop the tape on the source

VCR or camcorder.

AUDIO

Audio/Video

adapter cable

(not supplied)

OUT

VIDEO

- 24 -

9I03

ON SCREEN DISPLAY

To check the Counter, Clock, and Channel number on the TV screen, press the DISPLAY button on the remote

control. Each time you press the DISPLAY button on the remote control, the TV screen will change as follows:

WHEN THE CLOSED CAPTION MODE IS OFF:

Counter mode: After 5 seconds, only

the counter remains. To clear it, press

the DISPLAY button.

Clock mode: After 5 seconds, only

the clock and the channel number

remain. To clear them, press the DIS-

PLAY button.

•

5:40PM

CH2

Press

once

Press

once

COUNT 0:12:34

Press once

WHEN THE CLOSED CAPTION MODE IS ON:

OFF mode

Clock/Counter mode

The On Screen Display disappear after 5 seconds.

•

STOP

5:40 PM

CH2

This is true even if the MUTE button is pressed or the

PAUSE/STILL button is pressed while recording.

COUNT 0:12:34

SPECIAL FEATURES

REAL TIME TAPE COUNTER

AUTO REWIND-EJECT

This shows the elapsed recording or playback time in

hours, minutes and seconds. (The displayed time will

not change on a blank tape or blank portions on the

tape.)The “–” indication will appear when the tape

has rewound further than “0:00:00” on the tape

counter.

When the end of a tape is reached during record-

ing, playback or fast-forward, the tape will auto-

matically rewind to the beginning. After rewinding

finishes, the TV/VCR will eject the tape and turn

itself to off.

This function is operative when Repeat Play is set

to the [OFF] position.

•

The tape will not auto-rewind during timer record-

ing or One Touch Recording.

MAINTENANCE

back, the video heads in your TV/VCR may need

to be cleaned.

CABINET CLEANING

Wipe the front panel and other exterior surfaces of

the TV/VCR with a soft cloth immersed in luke-

warm water and wrung dry.

•

1. Please visit your local Audio/Video store and pur-

chase a good quality VHS Video Head Cleaner.

2. If a Video Head Cleaner does not solve the prob-

lem, please call our help line at 1-800-968-3429,

to locate an Authorized Service Center.

NOTES:

Remember to read the instructions included with

the video head cleaner before use.

Clean video heads only when problems occur.

Never use a solvent or alcohol. Do not spray insec-

•

ticide liquid near the TV/VCR. Such chemicals

may cause damage and discoloration to the

exposed surfaces.

•

AUTO HEAD CLEANING

•

Automatically cleans video heads as you insert or

remove a cassette, so you can see a clear picture.

•

SERVICING

Should your TV/VCR become inoperative, do not

try to correct the problem by yourself. There are no

user-serviceable parts inside. Turn off, unplug the

power cord and please call our help line at 1-800-

968-3429, to locate an Authorized Service Center.

Playback picture may become blurred or interrupt-

•

ed while the TV program reception is clear. Dirt

accumulated on the video heads after long periods

of use or the usage of rental or worn tapes can

cause this problem.

If a streaky or snowy picture appears during play-

- 25 -

9I03

TROUBLESHOOTING GUIDE

If you have followed the instructions contained in this manual, and have difficulty operating your TV/VCR,

locate the PROBLEM in the left column below. Check the corresponding CORRECTIVE ACTION column to

remedy the problem.

PROBLEM

CORRECTIVE ACTION

Make sure the AC cord is connected to an AC outlet.

Make sure the power is turned on.

Make sure the AC cord is connected to an AC outlet.

Check antenna connection.

Let the TV/VCR program its tuner memory.

Adjust direction or replace antenna.

Adjust picture controls.

Adjust volume control on remote control or main unit.

Press the MUTE button to restore sound.

Make sure the timer recording is set correctly.

Make sure the power is off.

Make sure the TV/VCR clock is set correctly.

Make sure the tape has an erase-prevention tab. If needed, cover the

hole with plastic tape.

No power.

•

No picture and sound.

No picture or poor picture on

TV/VCR.

No sound or poor sound.

•

Timer recording is not possible.

Cannot go into Record mode.

•

Playback picture is partially noisy.

Adjust tracking control for a better picture using the CHANNEL

or L button on the TV/VCR.

Head cleaning may be necessary. Refer to “AUTO HEAD

CLEANING” on page 25.

•

No picture but the audio is OK in

playback.

•

No operation by infrared Remote

Control.

Video or color fades in and out

when making a copy of a video tape

Different color marks on screen.

Make sure the AC cord is connected to an AC outlet.

Check batteries in remote control.

You can not copy a copyrighted video tape. You are experiencing

copy guard protection.

Magnetism from nearby appliances and geomagnetism might affect

the color of the TV picture. Move the TV/VCR away from the appli-

ances, the TV/VCR can repair itself automatically. If you want to

repair immediately, unplug the TV/VCR power cord, then plug it in

again 30 minutes or so later.

•

CLOSED CAPTION PROBLEM

My TV/VCR is showing captions

that are misspelled.

POSSIBLE REMEDY

• You are watching a live broadcast and spelling errors made by the

• closed captioning production company may pass through uncorrected.

• A prerecorded program will not show any misspelled words because

• of the normal time available for editing the captions.

My TV/VCR will not show the text • Captions that are delayed a few seconds behind the actual dialogue

in its entirety or there is a delay of • are common for live broadcast. Most captioning production companies

what is being said.

• can display a dialogue to a maximum of 220 words per minute. If a

• dialogue exceeds that rate, selective editing is used to insure that the

• captions remain up-to-date with the current TV screen dialogue.

• Interference caused by building, power lines, thunderstorms, etc.

• may cause scrambled or incomplete captions to appear.

My captions are scrambled with

white boxes on the TV screen.

My program guide listed a TV show • Broadcasters may at times use a time compression process to speed

as being closed captioned but none • up the actual program so that additional advertising time can be

of the captions were displayed.

• given. Since the decoder cannot read the compressed information,

• captions will be lost.

My prerecorded video tape does not • The video tape was either an illegal copy or the tape duplicating

show any captions. The tape box • company accidentally left out the captioning signals during the

mentions it being closed captioned. • copying process.

My TV screen shows a black box

on certain channels.

• You are in the TEXT mode. Select CAPTION mode to CAPTION

• [OFF].

- 26 -

9I03

SPECIFICATIONS

GENERAL SPECIFICATIONS

ELECTRICAL SPECIFICATIONS

CRT :

13 inch in-line gun, 90˚

deflection tube

NTSC-M

Video input level :

Audio input level :

0.5~2.0Vp-p

-15dBs

Television system :

Closed caption system :§15.119/FCC

Video S/N ratio : More than 46dB

Audio S/N ratio : More than 43dB

Video Heads :

Tape width :

Tape speed

SP :

LP :

SLP :

Tuner channel

TV VHF Low :

TV VHF High :

TV UHF :

CATV

Rotary two-head

1/2 inch

OTHER SPECIFICATIONS

Power requirement : AC 120V/60Hz

Power consumption : 60W

33.40mm/sec.

16.67mm/sec.

11.12mm/sec.

Dimensions :

H:15-5/16” (389mm)

W:14-7/16” (367mm)

D:14-7/8” (377mm)

23.1bs (10.5kg)

#2~#6

#7~#13

#14~#69

Weight :

Designs and specifications are subject to change

without notice.

If there is a discrepancy between languages, the

default language will be English.

•

VHF :

MID band :

SUPER band :

HYPER band :

Terminals

A5~A1, A~I

J~W

W+1~W+84

Antenna input :

VHF/UHF 75 ohms

unbalanced

Video input :

Audio input :

Earphone :

RCA connector [ 1

1/8” monaural (3.5 mm)

CABLE CHANNEL DESIGNATIONS

If you subscribe to cable TV, the channels are displayed as 1-125. Cable companies often designate channels

with letters or letter-number combinations. Please check with your local cable company. The following is a

chart of common cable channel designations.

CATV channel

TV Display

CATV channel

TV Display

CATV channel

W+1

W+2

W+3

W+4

W+5

W+6

W+7

W+8

W+9

TV Display

CATV channel

W+10 W+11 W+12 W+13 W+14 W+15 W+16 W+17 W+18 W+19 W+20 W+21 W+22 W+23 W+24

46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

W+25 W+26 W+27 W+28 W+29 W+30 W+31 W+32 W+33 W+34 W+35 W+36 W+37 W+38 W+39

61 62 63 64 65 66 67 68 69 70 71 72 73 74 75

W+40 W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48 W+49 W+50 W+51 W+52 W+53 W+54

TV Display

CATV channel

TV Display

CATV channel

TV Display

W+59 W+60 W+61 W+62 W+63 W+64

100 101 102 103 104 105

W+55 W+56 W+57 W+58

A-5

A-4

A-3

A-2

A-1

CATV channel

TV Display

CATV channel

W+65 W+66 W+67 W+68 W+69 W+70 W+71 W+72 W+73 W+74 W+75 W+76 W+77 W+78 W+79

TV Display

106

W+80 W+81 W+82 W+83 W+84

121 122 123 124 125

107

108

109

110

111

112

113

114

115

116

117

118

119

120

CATV channel

TV Display

- 27 -

9I03

CONTROLES DE OPERACIÓN Y SUS FUNCIONES

NOTA:

No recomendamos utilizar mandos a distancia universales. No todas las funciones pueden ser controladas mediante un

mando a distancia universal. Si decide utilizar un mando a distancia universal con esta unidad, tenga en cuenta que con el

número de código dado tal vez no se pueda controlar la unidad. En este caso, póngase en contacto con el fabricante del

mando a distancia universal.

VIDEO

AUDIO

POWER

VOLUME

CHANNEL

STOP/EJECT REW

PLAY

F.FWD

REC/OTR

EARPHONE

1 2

7 8 9

11 12

)–

4 Botones de volumen (VOLUME

Ajustan el nivel del volumen.

5 Botones de canales (CHANNEL K/ L)–

Púlselos para seleccionar los canales deseados

para ver o grabar.

WAKE-UP

POWER

/SLEEP

EJECT

CHANNEL

RETURN

Se puede mostrar el menú principal en la pantalla

del televisor pulsando repetidamente este botón

del televisor/videograbadora.

Función de seguimiento– Pulse los botones

para minimizar el ruido de vídeo (líneas o puntos

en la pantalla) durante la reproducción.

6 Ventanilla sensora del mando a distan-

cia– Recibe las señales infrarrojas procedentes

del mando a distancia.

7 Botón de expulsión (EJECT)–Púlselo en el

modo de parada para expulsar la cinta del televi-

sor/videograbadora.

CHANNEL

VOLUME

+100

DISPLAY

MUTE

PLAY

REW

F.FWD

STOP

Botón de parada (STOP)– Púlselo para

detener la cinta.

Botón L–

SPEED PAUSE/STILL

RECORD

T-PROG.

CLEAR

GAME

TIME SEARCH

Púlselo para seleccionar los modos de ajuste

desde el menú de la pantalla.

•

COUNTER

RESET

Púlselo para introducir dígitos cuando establez-

ca un programa.

•

(Por ejemplo: Para ajustar el reloj o establecer un

programa de temporizador)

8 Botón de rebobinado (REW)– Púlselo para

rebobinar la cinta, o para ver la imagen en retro-

ceso rápido durante el modo de reproducción.

(Búsqueda con rebobinado)

1 Toma de entrada de vídeo (VIDEO)–

Conéctela a la toma de salida de vídeo de su

videocámara u otra videograbadora.

2 Toma de entrada de audio (AUDIO)–

Conéctela a la toma de salida de audio de su

equipo de audio, videocámara u otra

videograbadora.

Botón s–

Púlselo para seleccionar un modo desde un

menúparticular.

•

(Por ejemplo: IDIOMA o ADJUST DE USER)

9 Botón de reproducción (PLAY)– Púlselo

para iniciar la reproducción.

3 Botón de la alimentación (POWER)–

Botón K–

Púlselo para encender y apagar el

televisor/videograbadora. Púlselo para activar la

grabación con temporizador.

Púlselo para seleccionar los modos de ajuste

desde el menú de la pantalla.

•

- 28 -

0I29

ANT.

Púlselo para introducir dígitos cuando establez-

ca un programa.

(Por ejemplo: Para ajustar el reloj o establecer

un programa de temporizador)

16 Botón de menú (MENU)– Púlselo para visu-

alizar el menú principal en la pantalla del televi-

sor.

17 Botón del visualizador (DISPLAY)–

Visualiza el contador o el número del canal actu-

al y la hora actual en la pantalla del televisor.

18 Botón de velocidad de cinta (SPEED)–

Púlselo para elegir la velocidad de grabación

deseada: SP/SLP.

•

10 Botón de avance rápido (F.FWD)– Púlselo

para avanzar rápidamente la cinta, o para ver la

imagen en avance rápido durante el modo de

reproducción. (Búsqueda con avance rápido)

Botón B–

Cuando establezca un programa (por ejemplo:

19 Botón T-PROG. CLEAR– Púlselo para cance-

•

para ajustar el reloj o para establecer un pro-

grama de temporizador), púlselo para determi-

nar su elección y vaya al paso siguiente que

quiera introducir.

lar un programa de temporizador.

Botón de reposición del contador

(COUNTER RESET)– Púlselo para reponer el

contador a 0:00:00.

Púlselo para determinar los modos de ajuste

•

20 Botón de juego (GAME)– Establece el modo

del juego y el modo de entrada externa al mismo

tiempo.

21 Botón de búsqueda con tiempo (TIME

SEARCH)– Púlselo para activar el modo de

búsqueda con tiempo.

desde el menú de la pantalla.

Púlselo para seleccionar un modo desde un

menúparticular.

•

(Por ejemplo: IDIOMA o ADJUST DE USER)

11 Botón de grabación (REC)– Púlselo para

iniciar la grabación manual.

22 Botón de pausa/imagen fija

(PAUSE/STILL)– Púlselo para detener tempo-

ralmente la cinta durante la grabación o para ver

una imagen fija durante la reproducción.

23 Botón de silenciamiento (MUTE)– Silencia

el sonido. Púlselo de nuevo para recuperar el

sonido.

24 Botón de retorno de canal (CHANNEL

RETURN)– Púlselo para volver al canal anteri-

or. Por ejemplo, pulsando una vez este botón, la

visualización del canal cambiará de 3 (canal

actual) a 10 (canal anterior), y al pulsarlo por

segunda vez, el canal cambiará del 10 al 3.

25 Botón del temporizador despertador/para

dormir (WAKE-UP/SLEEP)– Ajusta el tem-

porizador para despertarse/dormir.

Botón de grabación de un toque (OTR)–

Activa la grabación de un toque. (Sólo en el tele-

visor/videograbadora)

12 Indicador de grabación (RECORD)–

Parpadea durante la grabación.

Se enciende en el modo de espera de la

grabación con temporizador.

13 Toma de auriculares (EARPHONE)– Para

conectar los auriculares (no suministrados) y

escuchar en privado. La toma es mono y tiene un

tamaño de 1/8”(3.5 mm).

14 Compartimiento del videocasete

15 Botones numerados– Púlselos para selec-

cionar los canales deseados para ver o grabar.

Para seleccionar canales del 1 al 9, pulse primero

el botón 0 y luego el botón 1 a 9.

26 Cordón de alimentación– Conéctelo a la

toma de CA estándar (120V/60Hz).

Botón +100– Cuando seleccione canales de

televisión por cable cuyo número sea superior al

99, pulse primero este botón, y luego pulse los

dos últimos dígitos. (Para seleccionar el canal

125, pulse primero el botón “+100” y luego el

“2” y el “5”.)

27 Terminal de antena (ANT.)– Para conectar

una antena o sistema de televisión por cable.

- 29 -

0I29

CONEXIONES DE ANTENA/CABLE

Desde el cable coaxil o

caja de emisiones vía

satélite de 75 ohm del

sistema de Cable

Caja de CATV

o caja de emi-

siones vía satélite

(no incluído)

Antena combinada de

VHF/UHF

(no incluído)

Antena de varilla UHF/VHF

(incluído)

OUT

Antena VHF

(no incluído)

Antena UHF

(no incluído)

Desde el

sistema de Cable

ANT.

Combinador de

VHF/UHF

(no incluído)

ANT.

Cable coaxil

de 75 ohm (no incluído)

Cable bifilar plano

MODO DE ENTRADA EXTERNA

2 Seleccione “LANGUAGE”

Pulse el botón MENU en el mando

a distancia.

Pulse el botón PLAY/K o STOP/L

para señalar “LANGUAGE”.

– M E N U –

TIMER PROGRAMMING

PICTURE CONTROL

SETTING CLOCK

CHANNEL SET UP

USER’S SET UP

V-CHIP SET UP

LANGUAGE [ENGLISH]

CAPTION [OFF]

Cuando utilice una señal de entrada externa (otra

videograbadora o una videocámara), conecte los cables

de salida de audio/vídeo del equipo de reproducción a

las tomas AUDIO IN/VIDEO IN de su

televisor/videograbadora. Y luego pulse el botón

CHANNEL K o L hasta que “AUX” aparezca en la

pantalla.

ZERO RETURN

TIME SEARCH

Seleccione “ENGLISH”, “ESPAÑOL” o “FRANÇAIS”

Seleccione “ENGLISH”, “ESPAÑOL” o

“FRANÇAIS” con el botón F.FWD/B y pulse el

botón REW/s en el mando a distancia.

Usted puede programar el temporizador para que explore

todos los canales que puedan recibirse en su zona.

SELECCION DE IDIOMA

4 Salga del modo de idioma

Pulse el botón MENU en el mando a distancia para

volver al modo del televisor.

1 Enchufe el cordón de alimentación

del televisor/videograbadora

Enchufe el cordón de alimentación del

televisor/videograbadora en una toma de

CA estándar.

NOTA: Si, por alguna razón, el menú está en español

o francés, pulse el botón MENU en el mando a dis-

tancia, pulse el botón PLAY/K para señalar el

“IDIOMA (ESPAÑOL)” o “LANGAGE

(FRANÇAIS)”, a continuación, pulse el botón

F.FWD/B y pulse el botón MENU en el mando a

distancia.

NOTA:

•

Si aparecen algunas cifras en la esquina

de la pantalla, pulse el botón POWER sin desench-

ufar el cordón de alimentación.

Asegúrese de que ...

Pulse el botón POWER para encender el televi-

sor/videograbadora.

•

NOTA: Esta función afecta sólo el idioma en el

menú de la pantalla y no la fuente de audio.

- 30 -

0I29

AJUSTE DE CANAL

AJUSTE DEL RELOJ

Puede programar el sintonizador para buscar todos

los canales que recibe en su localidad.

Cerciórese...

La alimentación del televisor/videograbadora

deberá estar conectada.

En el ejemplo de abajo, el reloj va a ajustarse así:

FECHA: 6 de mayo de 2004

HORA: 5:40 PM

1) Pulse el botón MENU en el mando a distancia.

Pulse el botón PLAY/K o STOP/L para indicar

“AJUSTE RELOJ”.

Luego, pulse el botón F.FWD/B.

2) Pulse el botón PLAY/K o STOP/L para indicar

“AJUSTE MANUAL RELOJ”.

•

NOTA: El canal preparado NO es necesario cuando

esté conectado a una caja de cable o caja de satélite.

Sólo tiene que seleccionar con el selector de canal

del televisor/videograbadora al canal de salida de la

caja de cabe o caja de satélite (por ejemplo el canal

CH3). Seleccione el canal a ver en la caja de cable o

caja de satélite.

Asegúrese de que ...

Pulse el botón POWER para encender el televi-

sor/videograbadora.

•

Luego, pulse el botón F.FWD/B.

1 Seleccione “AJUSTE DE CANAL”

3) Pulse el botón PLAY/K o STOP/L hasta que

aparezca el mes deseado. (Ejemplo: Mayo - 05)

Luego, pulse el botón F.FWD/B.

4) Pulse el botón PLAY/K o STOP/L hasta que

aparezca el día del mes deseado. (Ejemplo: 6 -

06)

Pulse el botón MENU en el mando

– M E N U –

COMO PROGRAMAR

a distancia.

CONTROL DE IMAGEN

AJUSTE RELOJ

AJUSTE DE CANAL

AJUSTE DE USER

AJUSTE DE V-CHIP

IDIOMA [ESPAÑOL]`

TITULO [OFF]

Pulse el botón PLAY/K o el botón

STOP/L para señalar “AJUSTE DE

CANAL”.

RETORNO A CERO

BUSQUEDA DE HORA

A continuación, pulse el botón

F.FWD/B.

Luego, pulse el botón F.FWD/B.

5) Pulse el botón PLAY/K o STOP/L hasta que

aparezca el año deseado. (Ejemplo: 2004)

Luego, pulse el botón F.FWD/B.

6) Pulse el botón PLAY/K o STOP/L hasta que

aparezca la hora deseada. (Ejemplo: 5, PM)

Luego, pulse el botón F.FWD/B.

2 Empiece el prefijado automático

Pulse el botón PLAY/K o STOP/L

para señalar “AUTOPROGRAMA-

AJUSTE DE CANAL

–

AGREGAR/BORRAR (CATV)

B AUTOPROGRAMACION DE CA.

CION DE CA”.

7) Pulse el botón PLAY/K o STOP/L hasta que

aparezca el minuto deseado. (Ejemplo: 40)

8) Pulse el botón MENU en el mando a distancia.

Aunque los segundos no se visualizan, éstos

empiezan a contar desde 00 cuando se pulsa

MENU en el mando a distancia. Utilice esta fun-

ción para sincronizar el reloj con la hora correcta.

A continuación, pulse el botón

F.FWD/B.

El sintonizador busca y memoriza todos los canales

activos en su localidad.

3 Después de buscar

El sintonizador se detiene en el canal memorizado

más bajo.

Cuando se activa AUTOPROGRAMACION DE

•

CA, donde no hay entrada de señal del televisor,

aparecerá “NO HAY SEÑAL DE TV” en la pan-

talla después de terminar la búsqueda de canales.

El televisor/videograbadora puede reconocer los

•

canales de TV para que sean canales de TV de

antena de cable con las condiciones de recepción.

En este caso, pruebe nuevamente con el prefijado

automático en las condiciones de recepción fina.

- 31 -

LIMITED WARRANTY

FUNAI CORP. will repair this product, free of charge in the USA in the event of defect in materials or workmanship as follows:

DURATION:

PARTS:

FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the date of orig-

inal retail purchase. Two (2) years for Picture Tube. This warranty does not cover any cosmetic parts or complete

assembly parts.

LABOR:

FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of original retail

purchase.

LIMITS AND EXCLUSIONS:

This warranty is extended only to the original retail purchaser. A purchase receipt or other proof of original retail purchase will be

required together with the product to obtain service under this warranty.

This warranty shall not be extended to any other person or transferee.

This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing or if service was

attempted by an unauthorized service center. This FUNAI Limited warranty does not apply to any product not purchased and used in

the United States.

This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It does not cover dam-

age which occurs in shipment, or failures which are caused by repairs, alterations or product not supplied by FUNAI CORP., or dam-

age which results from accident, misuse, abuse, mishandling, misapplication, alteration, faulty installation, improper maintenance,

commercial use such as hotel, rental or office use of this product or damage which results from fire, flood, lightning or other acts of

God.

THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE CONTROL), ANY

COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.

FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY GENERAL, INDI-

RECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE USE OF OR THE INABILITY TO

USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, AND

OF ALL OTHER LIABILITIES ON THE PART OF FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF

MERCHANTABILITY, AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS

REPRESENTATIVES IN THE UNITED STATES. ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED

BYA FUNAI AUTHORIZED SERVICE CENTER. THIS WARRANTY IS VALID WHEN THE UNIT IS CARRIED-IN OR DELIV-

ERED TO A FUNAI AUTHORIZED SERVICE FACILITY.

IMPORTANT:

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS., YOU MAY HAVE OTHER RIGHTS THAT VARY

FROM STATE TO STATE, IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE UNABLE TO OBTAIN SATIS-

FACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI CORP. IN WRITING

SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION

OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGE SO THE ABOVE LIMITATION OR EXCLUSIONS MAY

NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER

RIGHTS WHICH VARY FROM STATE TO STATE.

ATTENTION:

FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT WITHOUT

PRIOR NOTICE.

To locate your nearest FUNAI Authorized Service Center or for general service procedure, please call 1-

800-968-3429 or write to the following:

FUNAI CORPORATION, INC. Service Center

19900 Van Ness Avenue, Torrance, CA 90501

Tel : 1-800-968-3429

Printed in Malaysia

1EMN20052

★★★★★

T5510UL

Sony Computer Accessories SMP N100 User Manual
Sony CRT Television KV 24FV300 User Manual
Sony Home Theater System VGX XL2A User Manual
Sony Portable Speaker SS FCRW115 User Manual
Sony Radio XDR S55DAB User Manual
Speco Technologies Digital Camera HTD8FFI HTB11FFI HT7248FFI User Manual
Stanton CD Player C402 User Manual
StarTechcom Network Card usb to rs232 serial adapter User Manual
Swann Security Camera Maxi Brite Cam User Manual
Sylvania Flat Panel Television LC370SS9 User Manual