®
©AMERIPHONE products are manufactured by Walker,
a Division of Plantronics, Inc.
12082 Western Avenue, Garden Grove, CA 92841
(800) 874-3005 VOICE • (800) 772-2889 TTY/TDD
(714) 897-4703 FAX
email: [email protected]
Table Of Contents
Safety Instructions . . . . . . . . .1
Operating Instructions . . . . . .7
Installation . . . . . . . . . . . . . .9
Specifications . . . . . . . . . . .13
Regulatory Compliance . . . .14
Warranty . . . . . . . . . . . . . .21
Your Satisfaction . . . . . . . . .23
E
N
G
L
I
S
H
Important Safety Instructions
When using your CA-100/200 Call Alert, basic
safety precautions should always be followed to
reduce the risk of fire, electric shock and persons
including the following:
1. Read and understand all instructions.
2. Follow all warnings and instruction
marked on the CA-100/200 Call Alert
.
3. Do not use this CA-100/200 Call Alert near
a bathtub, wash basin, kitchen sink or laundry
tub, in a wet basement, near a swimming
pool or anywhere else there is water.
4. Avoid using a telephone (other than a
cordless type) during a storm. There
may be a remote risk of electrical
shock from lightning.
5. Do not use the telephone to report a
gas leak in the vicinity of the leak.
6. Unplug the CA-100/200 Call Alert from the
wall outlets before cleaning. Do not use liquid
cleaners or aerosol cleaners on the product.
1
Use a damp cloth for cleaning.
7. Place this ringer on a stable surface.
Serious damage and/or injury may
result if the telephone falls.
8. Do not cover the slots and openings on this
product. It should never be placed near or
over a radiator or heat register. It should not
be placed in a built-in installation unless
proper ventilation is provided.
9. Operate this product using the electrical
voltage as stated on the base unit or the
owner’s manual. If you are not sure of the
voltage in your home, consult your dealer or
local power company.
10. Do not place anything on the power cord.
Install the product where no one will step or
trip on the cord.
11. Do not overload wall outlets or extension
cords as this can increase the risk of fire
or electrical shock.
12. Never push any objects through the
slots in the product. They can touch
2
E
N
G
L
I
S
H
dangerous voltage points or short out
parts that could result in a risk of fire
or electrical shock. Never spill liquid of
any kind on the product.
13. To reduce the risk of electrical shock, do
not take this product apart. Opening or
removing covers may expose you to
dangerous voltages or other risks. Incorrect
reassembly can cause electric shock when the
product is subsequently used.
14. Unplug this product from the wall outlets
and refer servicing to the manufacturer
under the following conditions:
A.When the power supply cord or plug is
frayed or damaged.
B. If liquid has been spilled into the product.
C.If the product has been exposed to
rain or water.
D.If the product does not operate
normally by following the operating
instructions. Adjust only those controls
that are covered by the operating
3
instructions. Improper adjustment may
require extensive work by a qualified
technician to restore the product to
normal operation.
E. If the ringer has been dropped or
the case has been damaged.
F. If the product exhibits a distinct
change in performance.
15. Never install telephone wiring during
a lightning storm.
16. Never install telephone jacks in wet
locations unless the jack is specifically
designed for wet locations.
17. Never touch uninsulated telephone
wires or terminals unless the telephone
line has been disconnected at the
network interface.
18. Use caution when installing or
modifying telephone lines.
19. Use only the power cord and batteries
indicated in this manual. Do not
dispose of batteries in a fire. They
4
E
N
G
L
may explode. Check with local codes
for possible special disposal instructions.
ADDITIONAL SAFETY NOTES FOR
CANADIAN USERS
I
S
H
The following items are included as part of the
CS-03 Requirements. The standard connecting
arrangement for the equipment is CA11A. This
product meets the applicable Industry Canada
technical specifications.
NOTICE: The Canadian Department of
Communications label identifies certified
equipment. This certification means that the
equipment meets certain telecommunications
network protective operational and safety
requirements. The Department does not
guarantee that the equipment will operate to the
user’s satisfaction. Before installing this equipment,
users should ensure that it is permissible to be
connected to the facilities of the local
5
telecommunications company. The equipment must
also be installed using an acceptable method of
connection. In some cases, the company’s inside
wiring associated with a single line individual
service may be extended by means of a certified
connector assembly (telephone extension cord). The
customer should be aware that compliance with the
above conditions may not prevent degradation of
service in some situations. Repairs to certified
equipment should be made by an authorized
Canadian maintenance facility designated by the
supplier. Any repairs or alterations made by the user
to this equipment, or equipment malfunctions, may
give the telecommunications company cause to
request the user disconnect the equipment.
6
E
N
G
L
I
S
H
Operating Instructions
Thank you for selecting this
product from Ameriphone.
Your Call Alert is manufactured
to exact performance, durability
and quality standards to provide
you years of convenient and
trouble free service.
Please read this guide before
connecting or using your Call
Alert and retain this guide for
future reference.
7
CA-200 ONLY
The Call Alert CA-200 comes as a
Master Unit and a Remote Unit
(each sold separately). The Master
Unit must be connected to a phone
line. When the phone rings, the
Master Unit will flash a connected
lamp to let you know that your
phone is ringing; at the same time it
sends out a carrier signal (through
the electrical wiring in your home) to
the Remote Unit. The Remote Unit
picks up the carrier signal and
flashes its connected lamp. The
Master Unit can operate and
function with a Master Unit. Up to
three Remote Units can be used
with a Master Unit.
8
E
N
G
L
Installation
CA-100or CA-200M - MASTER UNIT
I
1. A lamp is required to be
connected to the Call Alert as a
signaler. Use a
S
H
light bulb that is
300 watts or less.
Before
connecting the
lamp to the Call Alert, turn the
lamp on.
2. Unplug the lamp
from the wall
outlet, and plug
the lamp into
the Call Alert.
9
3. Plug the T-adapter
into the wall
phone outlet and
plug the phone
cord of the Call
Alert into one of the adapter
outlets. Then plug the cord of your
telephone into the other outlet.
4. Use the switch on the top of the
Call Alert to operate
your lamp. The lamp
will flash whenever
your telephone rings
whether the switch
is in the On or Off
position.
10
E
N
G
L
I
S
H
CA-200RX - REMOTE UNIT
1. A lamp is required to be
connected to the Call Alert
as a signaler. Use a light bulb
that is 300 watts or less. Before
connecting the lamp to the
Call Alert, turn the lamp on.
2. Unplug the lamp
from the wall
outlet, and plug
the lamp into the
Call Alert 200-RX
unit.
11
3. Use the switch at the top of the
Call Alert to operate your lamp.
The lamp will flash whenever your
telephone rings whether the
switch is in the On or Off
position.
12
E
N
G
L
Specifications
MASTER UNIT
I
S
H
Maximum Load: 300 watts @ 110 VAC
Max. loop length: 1400 ohms
Ringing Voltages: 53-120 RMS
On-Hook Leakage current:
5 micro-amps max. @ 53 volts
Tip & Ring DC Voltage: 53 volts max.
Operating Temperature: 40˚ to 100˚F
Output carrier signal frequency: 100 KHz
(other frequencies available from factory).
REMOTE UNIT
Maximum load: 300 watts @ 110 VAC
Operating Temperature: 40˚ to 100˚F
Output carrier signal frequency: 100 KHz
(other frequencies available from factory).
13
Regulatory Compliance
CA-100 & CA-200 MASTER UNIT ONLY
Part 68 of FCC Rules Information
This equipment complies with Part 68 of the FCC
rules. On the bottom of this equipment is a label
that contains, among other information, the FCC
registration number and ringer equivalence
number (REN) for this equipment. If requested, this
information must be provided to the telephone
company.
A plug and jack used to connect this equipment
to the premises wiring and telephone network
must comply with the applicable FCC Part 68
rules and requirements adopted by the ACTA. A
compliant telephone cord and modular plug, RJ11
USOC, is provided with this product. It is
designed to be connected to a compatible
modular jack that is also compliant. See
14
E
N
G
L
I
S
H
installation instructions for details. The REN is
used to determine the number of devices that may
be connected to a telephone line. Excessive RENs
on a telephone line may result in the devices not
ringing in response to an incoming call. In most
but not all areas, the sum of RENs should not
exceed five (5.0). To be certain of the number of
devices that may be connected to a line, as
determined by the total RENs, contact the local
telephone company. For products approved after
July 23, 2001, the REN for this product is part of
the product identifier that has the format
US:AAAEQ##TXXXX. The digits represented by
## are the REN without a decimal point (e.g., 03
is a REN of 0.3). For earlier products, the REN is
separately shown on the label.
If this product, the CA100/200 Call Alert causes
harm to the telephone network, the telephone
company will notify you in advance that
temporary discontinuance of service may be
required. But if advance notice isn’t practical, the
15
telephone company will notify the customer as
soon as possible. Also, you will be advised of
your right to file a complaint with the FCC if you
believe it is necessary. The telephone company
may make changes in its facilities, equipment,
operations or procedures that could affect the
operation of the equipment. If this happens the
telephone company will provide advance notice
in order for you to make necessary modifications
to maintain uninterrupted service.
If trouble is experienced with this product, for
repair or warranty information, please
contact Walker / Ameriphone, 1-800-874-3005.
If the equipment is causing harm to the telephone
network, the telephone company may request that
you disconnect the equipment until the problem is
resolved.
DO NOT DISASSEMBLE THIS EQUIPMENT.
16
E
N
G
L
I
S
H
This telephone equipment is not intended to be
repaired and it contains no repairable parts.
Opening the equipment or any attempt to perform
repairs will void the warranty. For service or
repairs, call 1-800-874-3005.
Connection to party line service is subject to state
tariffs. Contact the state public utility commission,
public service commission or corporation
commission for information.
If your home has specially wired alarm equipment
connected to the telephone line, ensure the
installation of this telephone equipment does not
disable your alarm equipment. If you have
questions about what will disable alarm
equipment, consult your telephone company or a
qualified installer. This telephone equipment is
hearing aid compatible.
We recommend the installation of an AC surge
arrester in the AC outlet to which this equipment
17
is connected. The telephone companies report
that electrical surges, typically lighting transients,
are very destructive to customer terminal
equipment connected to AC power sources.
Customer-Owned Coin/Credit Card Phones:
To comply with state tariffs, the telephone
company must be given notification prior to
connection. In some states, the state public utility
commission, public service commission or
corporation commission must give prior approval
of connection.
18
E
N
G
L
CA-100 , CA-200 MASTER UNIT & CA-200RX
Part 15 of FCC Rules Information
I
S
H
This device complies with part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference, and (2)
this device must accept any interference
received, including interference that may
cause undesired operation.
Your telephone equipment has been tested
and found to comply with the limits of a
Class B digital device, pursuant to Part 15 of
FCC rules. These limits are designed to
provide reasonable protection against
harmful interference in residential installation.
This equipment generates, uses, and can
radiate radio frequency energy and, if not
installed and used in accordance with the
19
instructions, may cause harmful interference
to radio communications. However, there is
no guarantee that interference will not occur
in a particular installation; if this equipment
does cause harmful interference to radio or
television reception, which can be
determined by turning the equipment off and
on, you are encouraged to try to correct the
interference by one of the following
measures:
Where it can be done safely, reorient the
receiving television or radio antenna.
To the extent possible, relocate the television,
radio or other receiver with respect to the
telephone equipment. (This increases the
separation between the telephone equipment
and the receiver.)
Connect the telephone equipment into an
outlet on a circuit difference from that to
which the television, radio, or other receiver
20
E
N
G
L
is connected.
Consult the dealer or an experienced
radio/TV technician for help.
I
S
H
CAUTION: Changes or modifications not
expressly approved by the manufacturer
could void the user’s authority to operate the
equipment.
THE PARTY RESPONSIBLE FOR PRODUCT
COMPLIANCE
Ameriphone Products by Walker,
A Division of Plantronics, Inc.
12082 Western Avenue
Garden Grove, CA 92841
Telephone: 800-874-3005
21
Industry Canada Technical Specifications
This product meets the applicable Industry
Canada technical specifications.
Before installing this equipment, users should
ensure that it is permissible to be connected to
the facilities of the local telecommunications
company. The equipment must also be installed
using an acceptable method of connection. In
some cases, the company’s inside wiring
associated with a single line individual service
may be extended by means of a certified
connector assembly (telephone extension cord).
The customer should be aware that compliance
with the above conditions may not prevent
degradation of service in some situations.
Repairs to certified equipment should be made
by an authorized Canadian maintenance facility
designated by the supplier. Any repairs or
alterations made by the user to this equipment,
or equipment malfunctions, may give the
22
E
N
G
L
I
S
H
telecommunications company cause to request
the user to disconnect the equipment.
Users should ensure for their own protection that
the electrical ground connections of the power
utility, telephone lines and internal metallic water
pipe system, if present, are connected together.
This precaution may be particularly important in
rural areas.
Caution: Users should not attempt to make such
connections themselves, but should contact the
appropriate electric inspection authority, or
electrician, as appropriate.
The Ringer Equivalence Number is an indication
of the maximum number of terminals allowed to
be connected to a telephone interface. The
termination on an interface may consist of any
combination of devices subject only to the
requirement that the sum of the Ringer
Equivalence Numbers of all the devices does not
exceed five.
23
[The term “IC:” before the certification/registration
number only signifies that the Industry Canada
technical specifications were met.]
24
E
N
G
L
I
S
H
Warranty
Ameriphone will repair or replace your
Call Alert for one year from the date of
purchase if the unit is defective in
workmanship or materials. Proof of
purchase is required. All applicable
implied warranties, including the
implied warranty of merchantability
and fitness for a particular purpose,
given to you by law are hereby limited
in duration of this warranty. UNDER
NO CIRCUMSTANCES WILL
AMERIPHONE BE LIABLE FOR ANY
INCIDENTAL OR CONSEQUENTIAL
DAMAGES.
You may also have other warranty
rights which vary from state to state.
25
OUT OF WARRANTY SERVICE:
After the one year warranty period
Ameriphone will repair or replace
parts for your unit at a minimal
charge. Contact our service
department for details.
26
E
N
G
L
I
S
H
Your Satisfaction
Your satisfaction with our product
is very important to us. We would
like to know what you like and
what you don’t like about this
product and what we can do to
make this even more beneficial to
you. Please give us your comments
by calling our Customer Service
Department toll free at (800) 874-
3005 VOICE, or (800) 772-2889
TTY. We value your comments and
thank you again.
27
|