User’s Guide
™
Models 3101-0 EASY VAC
™
Models 3102-0 EASY VAC PLUS
■
Assembly
Operation
■
■
Maintenance
■
Troubleshooting
Thanks for buying a BISSELL EASY VAC™ Bare Floor Vacuum System.
We’re glad you purch
Floor and Carpet vacuum.
care went into the design a
convenient, innovative hom
™
Your EASY VAC is we
with a comprehensive one-
behind it with a knowledge
Service department, so, sho
problem, you’ll receive fast,
My great-grandfather
in 1876. Today, BISSELL is
design, manufacture, and s
homecare products like you
Thanks again, from a
at BISSELL.
Mark J. Bissell
President and Chief Executive O
Crevice Tool
■
Cord Hook
Detachable
Canister Handle
Handle Release Buttons
1.
Quick-
Release
Cord Wrap
Hose Clip
5’ Stretch Hose
Crevice Tool
Attachment
Clip
Power
Cord
3.
Crevice Tool
Lightweight
Canister
Lower
Cord
Wrap
Hose Port
Dirt Cup
Floor Nozzle Surface Adjustment
Floor Brush
2.
Detachable
Floor Nozzle
Bottom View - Floor Nozzle
3
How to use this guide
Please read this Guide thoroughly before assembling
This User’s Guide has been designed to help you
get the utmost satisfaction from your BISSELL
your vacuum cleaner. Pay particular attention to the
assembly diagram, assembly instructions, and part
names. Locate and organize all parts before assembly.
Familiarize yourself with the parts and where they go.
Following this User’s Guide will greatly enhance your
ability to get the best performance from your BISSELL
™
EASY VAC Bare Floor and Carpet Vacuum. You’ll
find assembly and operating instructions, safety
precautions, as well as maintenance and
troubleshooting instructions.
™
EASY VAC for many years.
™
Your EASY VAC comes in four, easy to assemble components.
No tools are needed.
WARNING:
Do not plug in your
vacuum cleaner until
you have completely
assembled it per the
following instructions
and are familiar with
all instructions and
operating procedures.
Detachable Canister Handle
Lightweight Detachable Canister
Floor Nozzle
Crevice Tool
How to put it together
Attach Upright Handle to Canister Vacuum
1.
2.
Gently slide Handle over square end of Canister Vacuum, pushing until
buttons on Canister snap into place in opening on Handle. The Handle is
designed to attach and disassemble easily as you switch from upright to
canister style cleaning.
Attach Floor Nozzle to Canister Vacuum
Grasp Floor Nozzle with one hand, while holding Canister Vacuum firmly
with the other. With firm, even pressure, press Floor Nozzle into round
opening at end of Canister Vacuum. Continue pressing gently but firmly
until Floor Nozzle can go no further. As with the Upright Handle, the Floor
Nozzle is designed to attach and disassemble easily as you switch from level
floor to tool style cleaning.
Attach Crevice Tool to Tool Clip
Slide narrow end of Crevice Tool over angled post on the side of the
Canister, then press round end of Tool into semi-circular grip located just
below the Quick Release Cord Wrap.
3.
™
EASY VAC assembly is now complete.
4
™
How to use your BISSELL EASY VAC
Power Cord Quick Release
The Power Cord is stored at the side of the Canister,
looped around two Cord Wraps. A molded clip on
the polarized plug allows it to be clipped to the
Power Cord during storage.
1. Remove the plastic plug guard and dispose or
recycle it.
2. Unclip polarized plug from Power Cord.
3. Rotate the Upper Cord Wrap one-half turn
right or left, and slip Power Cord from Upper
and Lower Cord Wraps.
4. Connect Power Cord Plug with a polarized outlet.
5. To keep the Power Cord out of your way while
Index
Safety instructions . . . . . . . . . .2
Product view . . . . . . . . . . . . . .3
How to put it together . . . . . . .4
Index . . . . . . . . . . . . . . . . . . . .5
How to use your
Upper and
Lower Cord
Wraps
™
BISSELL EASY VAC . . . . . . .5-6
cleaning, place it in the cord hook at the top/back of the handle.
Maintenance . . . . . . . . . . . . . .7
Troubleshooting . . . . . . . . . . . .8
Replacement parts . . . . . . . . . .9
Warranty . . . . . . . . . . . . . . . .10
Consumer services . . . . . . . . . .10
Power Switch
The Power Switch is located just below the hand grip. Move the switch to
position “ ” [down] to vacuum, and “ ” [up] to turn unit off when
cleaning is complete.
Upright floor cleaning
Floor Nozzle Adjustment
You can adjust the brush on the underside of the Floor Nozzle to clean
bare floors or carpeted areas.
Floor Nozzle
Adjustment Lever
1. Move the lever on the Floor Nozzle to
the left ( ) for bare floor vacuuming,
and the brush will adjust to slight
variations in floor height.
2. Move the lever to the right ( ) and the brush will lock in position
for more effective cleaning of carpeted surfaces.
Cleaning with the Canister
™
Your BISSELL EASY VAC is not only a convenient upright bare floor
and carpet cleaner, it’s also a versatile floor/above floor vacuum
cleaner when you detach the lightweight canister.
Floor Cleaning
1. Detach the Upright Handle by pressing your thumb and fore
on the lock buttons on Canister (using a “pinching” motion
gently pulling Handle off square end of Canister.
2. For floor surface cleaning, use the Floor Nozzle, following th
surface adjustment instructions.
3. For edge cleaning or cleaning small areas, you need only to:
■
Detach the Hose from the Hose Port at the bottom/ back of the
Canister. Press the lock button and pull the Hose from the Port,
then insert the Crevice Tool into the end of the Hose. The Crevice
Tool also can be placed in the round opening of the canister for
added versatility.
5
Cleaning with the Canister - continued
Above Floor Cleaning
For quick and easy above floor cleaning:
1. Detach the Hose from the Hose Port at the bottom/back of the
Canister. Press the lock button and pull the Hose from the Port,
then insert the Crevice Tool into the end of the Hose.
To resume normal floor vacuuming:
1. Remove Crevice Tool and store in Crevice Tool Clip.
2. Reconnect Hose to the Hose Port, making certain it is locked
fully in place.
Tip:
Before cleaning
under low furni-
ture, check for
objects that
might block the
vacuum hose.
Do not pick up
hard or sharp
objects such as
glass, nails,
3. Attach Floor Nozzle and Upright Handle, following
instructions in “How To Put It Together,” page 4.
screws, coins,
paper clips, etc.
Emptying the Dirt Cup
™
Your EASY VAC features a translucent plastic Dirt Cup, so
you can easily see when it needs to be emptied. For best
performance, empty when debris reaches halfway up the cup.
1. Press the lock button down and forward
(away from the Canister Handle) while
Power Cord Storage
When you are done using your BISSELL
™
EASY VAC, store the Power Cord.
lifting the upper portion of the Dirt Cup
™
1. Turn EASY VAC off by moving
away from the Canister.
2. Grasp the Filter frame and pull it straight
from the Cup. Empty the Cup, and check
switch to “ ” position.
2. Unplug Power Cord by grasping the
polarized plug [NOT the cord) and
disconnect from outlet.
3. Loop Power Cord around Cord Wraps
on side of cleaner, making certain
Quick Release Cord Hook is pointed
up toward the Handle.
both the filter and the Cup for cleanliness
and damage. You may wash the Cup with
warm (not hot) water and mild liquid dish
soap only. Rinse and dry thoroughly before
reattaching it.
3. If the surface of the filter looks dirty or
discolored, now’s the time to clean or
4. Clip molded plug to Power Cord
to secure.
replace it. To clean the filter, remove any debris still clinging
to the filter. After a time, it will be necessary to replace your
filter. See “Routine Maintenance” for instructions.
4. With filter in place at the top of the Cup*, place the small
tab at the bottom of the Canister cavity, then press the upper
portion of the Cup into place until the lock button can
easily be pushed back into position.
*Push filter down tight to ensure gasket is in place.
6
Maintenance
™
To maintain maximum performance from your EASY VAC,
perform these simple maintenance checks periodically.
WARNING:
To
reduce the risk of electric
shock, turn Power Switch
OFF and disconnect
For average household use, follow this maintenance schedule:
polarized plug from
electrical outlet before
performing maintenance.
Weekly:
Check the debris level in the Dirt Cup and
empty if necessary.
Monthly:
Check the filter for wear and tear.
Remove debris from the filter. It may also
be necessary to use and old toothbrush to
clean off any debris. Replace as needed.
Tip:
Vacuuming new
carpet or fine
powders such as
drywall dust may
clog the filter, so
check it more
frequently. Shake
out or replace
as necessary.
Replace Filter
As you vacuum, dirt and debris are deposited in the Dirt Cup
while air passes through the filter before being returned to
the room. This process enhances the vacuum path while
dramatically reducing dust, dirt, and potential allergens from
the air you breathe. Replacing the filter periodically enhances
vacuum power and air quality. To replace the filter:
1. Remove the Dirt Cup.
2. Grasp the filter frame and pull it straight from the Cup.
Empty the Cup.
3. Replace the filter. Push new filter into place at the top of the
Cup, place the small tab at the bottom of the Cup into the
slot at the bottom of the Canister cavity, then press the upper
portion of the Cup into place until the lock button snaps
into place. Use only BISSELL Style 6, #32047 Filters
™
[package of 2] in your BISSELL EASY VAC Model 3101-0.
™
™
4. EASY VAC PLUS Model #3102-0 features a high efficiency
Filter for EASY-VAC Model 3101-0
3M Filtrete™ Filter. To keep your cleaner operating at peak
efficiency and to remove irritating allergens from your
home, you should change the FILTRETE filter every six
™
months. Use only BISSELL Style 6, #32046 Filters [package
of 2]. The cup-shaped filter lifts out from the top of the
Dirt Cup, and the new one fits into place.
You may purchase these filters:
■
at your local retailer
with the order form in this User’s Guide
by calling
■
■
™
™
BISSELL Consumer Services
1-800-237-7691
FILTRETE Filter for EASY-VAC PLUS Model 3102-0
Monday - Friday
Saturday
8 a.m. — 7 p.m. EST
9 a.m. — 2 p.m. EST
■
or from the BISSELL website —
http://www.bissell.com
7
Troubleshooting
WARNING:To reduce
the risk of injury from moving
parts, and/or electrical shock,
turn Power Switch OFF (position
“
”) and disconnect polarized
plug from electrical outlet
before performing
troubleshooting checks.
Vacuum cleaner won’t run.
Possible Causes
Remedies
Vacuum cleaner is not plugged in
Check electrical plug
Household fuse/breaker
Check/replace fuse or reset breaker switch
Call BISSELL Consumer Services
Vacuum cleaner won’t pick up dirt.
Possible Causes
Remedies
Dirt Cup is full
Empty Dirt Cup
Filter dirty
Check and remove debris. Replace if necessary
Check fit and tighten
Hose not secure in Hose Nozzle
Dirt Cup not sealed against Canister
Open Dirt Cup, then press firmly until you
hear lock button snap into place
Vacuum path clogged
Visually check: (1) Floor Nozzle, (2) Hose Port,
(3) Crevice Tool and (4) Hose for hair, pine
needles, small toys, large pieces of paper that
may be obstructing the vacuum path.
Carefully remove blockage
8
Part Numbers and Descriptions
Item Part No. Part Name
1
2
3
4
5
6
7
8
010-0031 Crevice Tool
010-0032 Filter (Polyester Fiber, 2/package)
010-0033 Filter (FILTRETE, 2/package)
010-0034 Dirt Cup (Blue) EASY VAC
™
™
™
010-0035 Dirt Cup (Purple) EASY VAC PLUS
010-0036 Upright Handle
010-0037 Floor Nozzle
010-0038 Floor Strip Brush
1
NOTE: Not all attachments pictured are included
with every model, but they are available.
To order replacement parts or additional
attachments call:
BISSELL Consumer Services
1-800-237-7691
Monday - Friday 8 a.m. — 7 p.m. EST
Saturday
9 a.m. — 2 p.m. EST
Or visit our Website @ http://www.bissell.com
2 & 3
Please have your model and part numbers of unit ready.
7
4 & 5
6
8
9
About your warranty
This warranty gives you specific legal rights, and you may also have other
rights which may vary from state to state. If you need additional instruction
regarding this warranty or have questions regarding what it may cover, call
BISSELL Consumer Services.
One Year Warranty
BISSELL Inc., upon receipt of the product, will repair or replace, free of charge,
any part which is defective or malfunctioning within one year of the purchase
date, provided that it is used for personal and not commercial or rental service.
If the vacuum cannot be repaired, BISSELL Inc. will replace the product or
refund the full price, at your option.
If your BISSELL product should require service:
1. Call BISSELL Consumer Services at 1-800-237-7691 and we will
give you the name and address of an authorized BISSELL Service
Center in your area.
2. If there is not an authorized BISSELL Service Center in
your area, one of our Service Representatives will be happy
to assist you. You can also visit the BISSELL website at
http://www.bissell.com to locate a Service Center near you.
— The product should be returned with a photocopy of
your proof of purchase. (Your dated sales receipt is your
warranty - send a photocopy, not the original.)
— Insure the product when shipping for your protection
from loss.
BISSELL Consumer Services
For information about repairs or replacement parts, or
questions about your warranty, call:
BISSELL Consumer Services
1-800-237-7691
Monday - Friday 8 a.m. — 7 p.m. EST
Saturday
9 a.m. — 2 p.m. EST
Visit our web site at http://www.bissell.com
Or write:
BISSELL INC
PO Box 3606
Grand Rapids MI 49544
ATTN: Consumer Services
©1998 BISSELL Inc
Grand Rapids, Michigan
All rights reserved. Printed in China.
Part Number 010-0039
Rev 12/98
When contacting BISSELL, have model number of unit available.
Please record your Model Number: ___________________
Please record your Purchase Date: ___________________
Visit our web site at:
NOTE: Please keep your original sales receipt. It is your warranty.
http://www.bissell.com
10
|