Cateye Bicycle Accessories HL EL830RC User Manual

HL-EL830RC  
Pat. and Design Pat. Pending Copyright©2007 CATEYE Co., Ltd. ENG  
1
2
3
4
5
6
7
INTRODUCTION  
Before using the light, be sure to thoroughly read this instruction manual  
and accompanying "Lithium-ion Batteries".  
This product combines high-power LEDs, Cateye Opticube lens technology, and compact  
lithium ion battery to produce a super bright, extremely durable high-performance light.  
1 Light unit  
2 Battery unit (lithium-ion batteries)  
3 Battery rubber pad  
4 Battery charger  
5 Bracket H34  
6 Fixing strap  
7 Cable straps (x 2)  
HOW TO MOUNT  
1
Installing Bracket  
5
1
Bracket rubber pad  
Attach the bracket to the handlebar.  
1. Wrap the bracket strap around the handlebar, and put it in the dial.  
2. Securely tighten the strap by turning the dial.  
CAUTION!: • Make sure to tighten the dial by hand. If you tighten it too hard with  
a tool, the screw threads may be stripped.  
• When the angle adjustment on the right and left sides is loose,  
tighten the screw.  
3. Cut off the excess bracket strap extending from the dial.  
Dial  
Screw  
CAUTION!: Round off the cut edge of the bracket strap to prevent injury.  
Bracket strap  
Attaching/removing the Light unit  
2
1
2
• Attaching/removing the Light unit  
Slide the light unit into the bracket as shown.  
To remove unit after use, pull it out while pressing the button on the bracket.  
CAUTION!: Make sure the light unit is cool to the touch before removing it.  
• Attaching/removing the switch  
Button  
Attach the switch to the handlebar as shown.  
CAUTION!: Mount the switch unit where it does not interfere with the handling of  
the bicycle. Make sure that it is securely mounted.  
Rubber strap  
1. Hold the switch at the mounting position and hook the strap on the switch from  
under the bar.  
Switch  
Handlebar  
Installing Battery unit  
Mount the battery unit onto the bicycle frame as shown.  
1. Put the battery unit through the loop of the fixing strap.  
CAUTION!: Check that the position of the fixing strap is within the installation  
range of the battery rubber pad of the battery unit.  
2. Secure the battery unit by wrapping the fixing strap around the top tube so that the  
battery rubber pad comes into contact with the frame.  
CAUTION!: Do not wrap the fixing strap from above the cables.  
Doing so is dangerous because it may interfere with braking and gear  
shifting.  
3
3
4
Gear & Brake Cables  
6
To Top tube  
3
Installation range  
Top tube  
6
2
Connecting and Securing cables  
Connect the light unit with the battery as shown.  
1. Connect the plug of the light unit to the battery unit as shown in the figure.  
4
CAUTION!: Slide the ring of the plug forward and turn it to lock the plug. It must  
remain locked when in use.  
2. Fix the cables to your frame and/or stem to keep them secured.  
CAUTION!: • Pay attention to the arrangement of the cable so that it does not  
interfere with the handling of the bicycle. Do not secure the cable at  
an acute angle because the wire inside the cable may break.  
• Adjust the beam angle according to “How to Adjust the Beam Angle”  
in this manual.  
Ring  
7
LOCK  
 

Breville Blender BSB400 User Manual
Breville Printer Accessories BHM500RXL User Manual
Briggs Stratton Pressure Washer 73005 User Manual
Bryant Furnace 369RAN User Manual
Cal Flame Patio Furniture Woodcrest Series User Manual
Canon Photo Printer iP5200 User Manual
Cateye Bicycle Accessories ROAD User Manual
Chauvet Music Pedal FS 4200 User Manual
Chicago Electric Mixer 65760 User Manual
Cisco Systems Cordless Telephone SPA302D User Manual