Sound That Will Move You
US PATENT # 6,675,931 B2
S H A L L O W
W O O F E R
S Y S T E M
SWS-6.5X (4-Ohm)
SWS-8X (4-Ohm)
SWS-8Xi (2-Ohm)
SWS-10X (4-Ohm)
SWS-12X (4-Ohm)
SWS-15X (4-Ohm)
Installation Reference Guide
The Sound That Will Move You.
Earthquake Sound reserves the right to amend details of the specifications without notice.
Copyright © Earthquake Sound Corporation
Earthquake Sound Corporation • 2727 McCone Avenue Hayward CA, 94545
Phone: 510-732-1000 Fax: 510-732-1095
SPECIFICATIONS
SWS Enclosures
SWS subwoofers are designed to bring bass virtually anywhere in a car: in front doors,
rear doors, dash board, center console, under seats, rear decks, and in any space limited
mounting depth. The following volumes shown below are created to give you optimized
"deep bass from the shallowest space".
Actual RMS power varies based on box design and on music played
SWS-15X
• Speaker diameter = 15"
• Mounting depth = 3 1/4"
• Cut out mounting hole = 13 3/4"
• Weight = 15Lbs
(81mm)
(3 1/4")
In order to match a box volume that bests suites your needs, you will need to find out the
amount of space that you have to work with, then use the formula below to find out which
range you will should be in based on our recommendations.
• Voice Coil diameter = 2.5"
• Aluminum bobbin / wire
• Power rating RMS = 400W
• Power rating MAX = 800W
• Revc = 3.76 Ohms
(350mm / 13 3/4")
(cut out hole diameter)
Choosing an enclosure type that perfectly tailors to your needs can sometimes be a hassle
and unfortunately choosing or building the wrong enclosure could potentially destroy the
sound quality of your system. The SWS subwoofers deliver truly prenominal bass response
from the shallowest of places. And in order to harness their greatness you will need to
make sure that your enclosure will be suffice for your application.
Actual RMS power varies based on box design and on music played
SWS-12X
• Speaker diameter = 12"
• Mounting depth = 3"
Sealed Enclosures:
• Cut out mounting hole = 11 3/8"
• Weight = 13Lbs
(75mm)
(3")
Do you often turn the bass down on a car or home stereo system because it sounds boomy
to you? If you do, a sealed enclosure is an excellent choice, especially if you listen to a
wide variety of music. This type of enclosure produces well-defined, strong, but not
overpowering bass.
• Voice Coil diameter = 2.5"
• Aluminum bobbin
• Power rating RMS = 300W
• Power rating MAX = 600W
• Revc = 3.76 Ohms
(288mm / 11 3/8")
(cut out hole diameter)
Bandpass Enclosures:
This bass is not really punchy, it's more like a massive, swampy force of low end that
powers the music which can be great for some tunes and extremely overwhelming on
others. If you prefer the harder stuff (metal, hard rock, industrial) or music with impact bass
content (reggae, hip hop) and you like your bass to be LOUD, the bandpass box is a great
way to go. And, if your amplifier is lacking in the power department, you'll get the most bang
for your buck from this design.
Actual RMS power varies based on box design and on music played
SWS-10X
• Speaker diameter = 10"
• Mounting depth = 2 11/16"
• Cut out mounting hole = 9"
• Weight = 11Lbs
• Voice Coil diameter = 2"
• Aluminum bobbin
• Power rating RMS = 200W
• Power rating MAX = 400W
• Revc = 3.76 Ohms
(68mm)
(2 11/16")
Ported Enclosure:
The ported box is also exceptionally loud, so it will also be a good choice if you have limited
power available. If you listen to a wide range of music and if you're always cranking up the
bass when you listen to tunes.
(228mm / 9")
(cut out hole diameter)
Actual RMS power varies based on box design and on music played
SWS-8X/8Xi
• Speaker diameter = 8"
• Mounting depth = 2 1/8"
CAUTION:
Earthquake Subwofoers are capable of generating high sound pressure
levels. You should exercise caution when operating these
subwoofer/amplifier systems. Long term exposures to high levels of sound
CAUTION:
THE 2-OHM SWS-8XI
(52mm)
(2 1/8")
• Cut out mounting hole = 7 7/8" IS FOR FACTORY
pressure will cause permanent damage to your hearing. Sound pressure levels exceeding
85dB can be dangerous with constant exposure. Set your audio system to a comfortable
loudness level. Earthquake Sound Corporation does not assume liability for damages
resulting from the direct use of Earthquake amplifiers or other Earthquake products , and
urges users toplay their music at moderate listening levels.
UPGRADED VEHICLES
• Weight = 8 Lbs
• Voice Coil diameter = 1.5"
• Aluminum bobbin
ONLY
(206mm / 8- 1/8")
(cut out hole diameter)
• Power rating RMS = 150W
• Power rating MAX = 300W
• Revc = 8=3.76 Ohms / 8Xi=1.76 Ohms
SOUND LEVEL DBA
DURATION IN HOURS
THE CHART (ON THE SIDE)
S H O W S T H E U . S .
Actual RMS power varies based on box design and on music played
90
92
95
8
6
4
3
2
G
O
V
E
R
N
M
E
N
T
S
SWS-6.5X
OCCUPATIONAL SAFETY AND
HEA LTH A DMINISTRATION
(OSHA) REGULATIONS WHICH
WERE IN EFFECT AT THE TIME
OF THIS PUBLICATION FOR
• Speaker diameter = 6.5"
• Mounting depth = 1 3/4"
• Cut out mounting hole = 5 3/4"
• Weight = 5 Lbs
• Voice Coil diameter = 1"
• Aluminum bobbin
• Power rating RMS = 100W
• Power rating MAX = 200W
• Revc = 3.6 Ohms
(45mm)
(1 3/4")
97
100
102
105
110
115
1 - 1 1/2
1
1/2
(142mm / 5 3/4")
(cut out hole diameter)
P E R M I S S I B L E
N O I S E
EXPOSURE, PER 29CFR1910.95,
TABLEG-16.
1/4 or l es s
All Specifications Are Subject To Change Without Notice
4
5
Calculating Enclosure Dimensions
Examples Of Limited Space Applications
Finding Box Dimensions For Recommended Enclosure Volumes:
To find the volume best suited for you, you will need to measure the max and min Height,
Width and Depth of the area where you to plan to place the sub-enclosure. Then subtract
1.5" each dim to get the internal dims. Now use the internal H, W & D in the formula below
to match your dims with one of our recommended ranges.
Enclosure;
Made With 3/4" Medium
Density MDF
D
W
Volume
H
External Dims:
H=10 x W=10 x D=5
Internal Dims:
H=8.5 x W=8.5 x D=3.5
To Get The Internal Dims Simply Subtract
The Total Thickness Of The MDF From The
External Dims;
Which With 3/4" MDF Is 1-1/2"
FORMULA
8.5 x 8.5 x 3.5 + 1728 = 0.15cu.ft.
CAUTION: In some cases when the enclosure will be placed with the sub facing down or
the sub butted up against the back of seat (like the illustration). You will need to either add
a grille or use 1" strips of your MDF and place as shown above. This will create an
excursion cushion so that it doesn't rub or get damaged.
All Specifications Are Subject To Change Without Notice
6
7
SWS-6.5 Recommended Applications
Example Minimum Sealed Designs (8,10,12 & 15" Models)
The SWS 6.5 woofer is designed to replace any stock / factory installed 6.5" driver. It
brings bass virtually anywhere in a car: in front doors, rear doors, dash board, center
console, under seats, rear decks, and in any space less than 2" deep.
SWS-8/8Xi Minimum Sealed Example
11-1/2"
17-1/2"
19-1/2"
21-1/2"
External Dimensions: 11" x 11-1/2" x 5"
Internal Dimensions: 10" x 9" x 3-1/2"
Internal Volume: 0.19cu.ft. (5.44Ltr.)
5"
5-1/2"
5-1/2"
8"
Recommended Sealed Internal Volume (8,10,12 & 15" Models)
11"
0.19cu.ft. (5.44Ltr)
0.60cu.ft. (16.99Ltr)
Minimum:
Maximum:
SWS-8/8Xi
SWS-8/8Xi
0.38cu.ft. (10.76Ltr)
0.75cu.ft. (21.23Ltr)
Minimum:
Maximum:
SWS-10X
SWS-10X
SWS-10X Minimum Sealed Example
External Dimensions: 12" x 17-1/2" x 5.5"
Internal Dimensions: 12" x 16" x 4"
Internal Volume: 0.38cu.ft. (10.76Ltr.)
0.56cu.ft. (15.85Ltr)
1.25cu.ft. (35.39Ltr)
Minimum:
Maximum:
SWS-12X
SWS-12X
1.20cu.ft. (33.98Ltr)
2.5cu.ft. (70.79Ltr)
Minimum:
Maximum:
12"
SWS-15X
SWS-15X
Our Examples and Reccomendations Are Calculated Assuming That 3/4" MDF Is Being Used
3/4"
MDF
SWS-12X Minimum Sealed Example
External Dimensions: 15" x 19-1/2" x 5-1/2"
Internal Dimensions: 13-1/2" x 18" x 4"
Internal Volume: 0.56cu.ft. (15.85Ltr.)
In some cases when the enclosure will be placed with
the sub facing down or the sub butted up against the back
of seat. You will need to either add a grille or use 1" strips of
your MDF and place as shown above. This will create an
excursion cushion so that it doesn't rub or get damaged.
15"
1" - 1.5" Depending On The Woofer
SWS-15X Minimum Sealed Example
External Dimensions: 17-1/2" x 21-1/2" x 8"
Internal Dimensions: 16" x 20" x 6-1/2"
Internal Volume: 1.20cu.ft. (33.98Ltr.)
One Subwoofer
Two Subwoofers
17-1/2"
SWS subwoofers will handle crazy amounts of power in any of the recommended enclosures,
minimum or maximum. The compact enclosures are best for use in limited-space applications.
The larger recommended enclosures will deliver
frequencies ranges.
a
bit more bass at the lowest
All Specifications Are Subject To Change Without Notice
8
9
EARTHQUAKE 5 YEAR LIMITED WARRANTY
Regarding Your Warranty:
(D) Warranty Limitations:
Warranty does not cover products that have been modified or abused. Including
but not limited to the following:
• Damages to speaker cabinet and cabinet finish due to misuse, abuse, or use of improper
use of cleaning materials/methods.
Thank you for choosing Earthquake Sound’s line of SWS subwoofers for superior
enhancement of your vehicle’s audio system from any location. With proper installation and
responsible listening, your SWS subs will give you years of phenomenal listening
enjoyment.
• Bent speaker frame, broken speaker connectors, holes in speaker cone, surround & dust
cap, burnt speaker voice coil.
• Fading, deterioration of speaker components & finish due to improper exposure to
elements.
• Bent amplifier casing, damaged finish on the casing due to abuse, misuse, or improper
use of cleaning material.
• Burnt tracers on PCB.
We strongly recommend you to have your new SWS subs installed by an authorized
Earthquake Sound dealer: Installation professionals employed by your dealer have the
correct tools and knowledge to install your speakers neatly and successfully. Also, when
your new products are installed by an authorized dealer, your product will include a FIVE
YEAR LIMITED WARRANTY. If you choose to perform your own installation, your warranty
will be subject to limitations. Over the counter authorized dealer warranties may very from
one dealer to the next. Please read the warranty information in its entirety and use good
judgment when making these vital decisions.
• Product/part damaged due to poor packaging or abusive shipping conditions.
• Subsequent damage to other products.
A warranty claim will not be valid if the warranty registration card is not
properly filled & returned to Earthquake with a copy of the sales invoice.
Five (5) year limited warranty:
(E) Service Request:
Earthquake warrants the original purchaser that all Factory Sealed New Audio
Products be free from defects in material and workmanship under normal and proper use
for a period of five (5) years from the date of purchase (as shown on the original bill of sale
with serial number affixed/written on it). The five (5) year warranty period is valid only if an
authorized Earthquake dealer properly installs the product and the warranty registration
card is properly filled out and sent to Earthquake Sound Corporation. If a non-authorized
party installs the product a ninety (90) day warranty period will be applied.
To receive product/s service, contact Earthquake service department at (510)
732-1000 and request an RMAnumber (Return MaterialAuthorization), items shipped without
a valid RMA number will be refused. Make sure you provide us with your complete/correct
shipping address, a valid phone number, and a brief description of the problem you are
experiencing with the product. In most cases, our technicians might be able to resolve the
problem over the phone, thus eliminating the need toship the product.
(F) Shipping Instructions:
(A) Five (5) years limited warranty plan coverage guidelines:
Product/s must be packaged in its original protective box(s) to minimize
transport damage. Shipper claims regarding items damaged in transit must be presented to
carrier. Earthquake Sound Corporation reserves the right to refuse product improperly packed.
Original bill of sale must accompany product returned for service. We encourage you to include
with the package a written description of the problem. Ship product to: Earthquake Sound
Corp. 2727 Mc ConeAvenue, Hayward, CA94545. Ph (510) 732-1000. You are responsible for
the cost of shipping the product toEarthquake Sound Corporation.
• First year: Earthquake pays for labor, parts, and ground freight (only in US mainland, not
including Alaska and Hawaii).
• Second year: Earthquake pays for labor and parts only, customer must pay freight both
ways.
• Third, fourth & fifth year: Earthquake pays labor only. Customer must pay for parts and
freight both ways.
(B) Warning:
(G) Disputes Resolution:
Products (sent for repair) that are tested by Earthquake technicians and deemed
to have no problem(s) will not be covered by the five (5) year limited warranty. Customer
will be charged a minimum of one (1) hour of labor (ongoing rates) plus shipping charges
back to customer.
All disputes - between clients and Earthquake Sound Corporation - resulting
from the five (5) years limited warranty policy must be resolved according to the laws &
regulations of the county ofAlameda -California.
(C) Earthquake will repair or replace - at our option - all defective products/parts
subject to the following provisions:
• Defective products/parts have not been altered or repaired by other than an Earthquake
factory approved technician.
• Products/parts are not subjected to negligence, misuse, improper use, or accident,
damaged by improper line voltage, used with incompatible products, or have its serial
number or any part of it altered, defaced or removed, or have been used in any way that
is contrary to Earthquake's written instructions.
Alternatively you may register your products online at
Warranty Continued On Next Page
All Specifications Are Subject To Change Without Notice
10
11
|