LIMITED LIFETIME WARRANTY
Freestyle U.S.A. warrants, to the
original purchaser, that its watches
are free from defects in materials
and workmanship for the lifetime
of the watch (under normal use)
from date of original purchase.
The following are not covered under
warranty: battery, strap/bracelet/
band and crystal.
home time (TIME), home time alarm
(ALM1), stopwatch (STW) and
countdown timer (TMR).
2
3
Press the S1 button once to start
the stopwatch. The watch will start
counting from 00'00''00 if the
watch is cleared. Otherwise, it will
pick up from where it last left off.
The watch will count up to 59
minutes and 59.99 seconds before
starting from zero again.
HOW TO DISPLAY THE DATE
To display the date, press S1 when the
time is displayed. Press the button
again to go back to time display. The
watch will also do so automatically
after six seconds.
FOLLOW THESE 8 TIPS TO GET THE
MOST OUT OF YOUR NEW WATCH!
To change from one display mode to
another, press the S3 button once. The
mode description will appear for two
seconds before activating the selected
mode.
1. Never Pull out the crown or operate
the pushers/buttons under water.
HOW TO SET THE DAILY ALARMS
SHARK CLASSIC
To stop counting, press the S1
button once. Press the button
again to resume from where it left
off. To clear the stopwatch, press
the S1 button to stop counting and
then press the S2 button.
1
2
3
Select alarm function using the S3
button.
HOME AND FOREIGN DISPLAY
2. Make sure your crown is returned
to the original position before you
expose your watch to water.
Accidental breakage or damage
due to normal wear or misuse of
the product, including but not limited
to the mathematical accuracy of
the product, is not covered under
this warranty. Some states do not
allow limitations on how long an
implied warranty lasts, or the
exclusions of or limitations on
consequential damages, so the
above limitation may not apply to
you. This warranty gives you
FEATURES:
To display the foreign time, press S2
when the home time is displayed. The
mode description (TM-2) will appear
shortly before the foreign time is
displayed. To change back to the home
time, press S2.
Select home and foreign time alarm
using the S2 button.
• CURRENT TIME
• DAY/MONTH/DATE
• TWO DAILY ALARM
• HOURLY CHIME
• STOPWATCH
• OPTIONAL 24-HR. TIME
• WATER RESISTANT TO
300FT/100M
• NIGHT VISION™
BACK LIGHT
3. If your watch is exposed to
saltwater it is very important to
wash it thoroughly under tap water
and wipe dry with a soft cloth.
Keep it clean!
Hold the S2 button for two seconds.
The SET message will appear. The
minute digits will blink.
The stopwatch is equipped with a split
function for you to keep track of
individual lap time. To use the function,
4
5
Use the S1 button to set the
minutes.
To display the daily alarm for foreign
time, press S2 when the daily alarm
for home time is displayed. The mode
description (ALM 2) will appear shortly
before the foreign time alarm is
displayed.
1
While the stopwatch is running,
press the S2 button once whenever
you want to register a lap. The
stopwatch is still running in the
background. To display the
currently accumulated time, press
the S2 button.
4. Sever impacts or drops may affect
your watches water resistance
and performance.
Press the S3 button. The hour digits
will blink.
specific legal rights, and you may
have other rights, which vary from
state to state.
KEY TO SYMBOLS
6
7
Use the S1 button to set the hours.
5. Avoid exposing your Freestyle
watch to extreme temperatures
such as in a hot shower, Jacuzzi,
sauna or hot tub. The combination
of extreme heat and water may
cause your watch to lose some of
its water resistance.
Press the S2 button to confirm and
exit.
Under this warranty FREESTYLE
will make any necessary repairs, if
applicable, at no cost to you the
consumer. Any repair needed that
is not under warranty will be at the
cost of you the consumer. Proof
of purchase and / or original receipt
it needed to validate your warranty.
HOW TO SET THE TIME AND
DATE
2
3
Repeat the last step until you have
registered all the laps.
HOW TO USE THE DAILY ALARMS
AND HOURLY CHIMES
To display the alarm time, select ALM
1 or ALM 2 mode using the S2 button
in alarm mode.
1
2
3
Select time display using the S3
button.
LIGHT
S3
S1
S2
Press S1 to stop counting. Press
the button again to resume or
press the S2 button to clear.
Select home time or foreign time
using the S2 button.
6. Avoid exposing your watch to
chemicals, soaps or solvents as
they deteriorate the water resist
seals in your watch.
Note: You can leave the stopwatch
running while switching over to other
operating modes. The STW indicator
will light up as a reminder.
Hold the S2 button for two seconds.
The SET message will appear
momentarily. The second digits
will blink.
Use the S1 button to set the status of
the alarm and chime functions of the
chosen alarm. Press the button once
to activate the daily alarm. Press the
button again to activate the hourly
chime. Press the button a third time
to activate both functions. To deactivate
both, press the S1 button a fourth time.
Your warranty is voided by any
servicing out by a non-authorized
agent. Any other form of guarantee
to you by the retailer is his / her
responsibility. This warranty applies
to watches purchased in the United
States. For watches purchased
outside the United States, please
contact you authorized
7. Never try to remove the caseback,
leave this to a certified watch repair
technician or Freestyle service
center. This will help in preventing
water leakage from improper
battery replacement.
4
5
6
Press the S1 button to reset the
second digits to 00.
HOW TO USE THE TIMER
To set the count down time,
1
INTRODUCTION
Select timer mode using the S3
button. The last selected timer
setting will be displayed.
Press the S3 button. The minute
digits will blink.
Congratulations on your purchasing
the Easy-Set Watch II. Designed for
easy operation, the watch
automatically tells you which button
to use in a setting procedure. The
watch has the following functions:
The chime and alarm indicators will
appear when their respective functions
are active.
FREESTYLE dealer for warranty
information.
Use the S1 button to set the
minutes. Press the button once to
increase the digits by one unit or
speed up the process by holding
down the button.
8. It is advisable to have your watch
pressure tested annually and to
re-furbish your watch every 2-3
years to extend the life of the watch.
2
Use the S2 button to alter the
setting. You can select among 1,
3, 5, 10, 15, 20, 25, 30, 45 and 60
minutes.
WHEN AN ALARM OR HOURLY
CHIME GOES OFF
•
•
•
Real-time calendar clock for home
time
To start a countdown, press the S1
button. Press the button again to stop
the countdown or a third time to
resume from where it left off.
7
Press the S3 button. The hour
digits will blink.
A tune will go off by the hour if the
hourly chime function is activated and
a 20-second alarm tune will be emitted
at the designated time when the alarm
is active. To stop either tune, press any
button.
Second calendar clock for foreign
time
8
9
Use the S1 button to set the hours.
Follow the same pattern to set the
day-of-the-month,month, day-of-
the-week, hour format and date
format.For the hour format, you
can choose 12-hour display with
P indicator or 24-hour display. As
for the date format, you can choose
M-D (month-day) or D-M (day-
month). The chosen formats will
apply to both home and foreign
settings.
Dual daily alarms and hourly
chimes
After reaching zero on a countdown,
a 20-second beep will go off. To stop
the beeping, press any button. The
timer will reload automatically.
•
•
Stopwatch with split function
10 preset countdown timers
To disable the functions, select ALM 1
or ALM 2 and use S1 button to turn off
the indicator of the function as desired.
The watch is also equipped with an EL
back light to facilitate time reading at
night or in dim light.
BATTERY INFORMATION
The watch uses a 3.0V lithium button
cell battery, which in normal
circumstances will be good for 1-2
years. However, the battery life will
vary due to shelf time and the manner
the watch is used.
HOW TO USE THE STOPWATCH
For a straight forward count-up,
HOW TO USE THE BACK LIGHT
Press the LIGHT button once to turn
on the back light for three seconds.
1
Select stopwatch mode using the
S3 button. The last recorded time
of the stopwatch will be
10 Press the S2 button to confirm the
settings and return to current time
display.
displayed.Press the S2 button to
clear the old record.
DISPLAY MODES
The watch has four display modes:
TRIM
|